View TQP7M9102_9139371.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 1 of 26 www.qorvo.com ? 3 pin sot-89 package general description the TQP7M9102 is a high linearity driver amplifier in a low- cost, rohs compliant, surface mount package. this ingap/gaas hbt delivers high performance across a broad range of frequencies with +44 dbm oip3 and +27.5 dbm p1db while only consuming 135 ma quiescent current. all devices are 100% rf and dc tested. the TQP7M9102 incorporates on-chip features that differentiate it from other products in the market. the amplifier integrates an on-chip dc over-voltage and rf over-drive protection. this protects the amplifier from electrical dc voltage surges and high input rf input power levels that may occur in a system. on-chip esd protection allows the amplifier to have a very robust class 1c hbm esd rating. the TQP7M9102 is targeted for use as a driver amplifier in wireless infrastructure where high linearity, medium power, and high efficiency are required. the device an excellent candidate for transceiver line cards in current and next generation multi-carrier 3g / 4g base stations. functional block diagram top view product features ? 400? C? 40 00?mhz ? +2 7.5 ? dbm p1db ? + 44 ? dbm output ip3 ? 17. 8 ?db gain at 2140?mhz ? +5?v single supply, 135 ? ma current ? internal rf overdrive protection ? internal dc overvoltage protection ? on -chip esd protection ? sot-89 package applications ? repeaters ? mobile infrastructure ? cdma / wcdma / lte ? general purpose wireless ordering information part no. description TQP7M9102 0.5 w high linearity amplifier TQP7M9102-pcb900 869? C?960 mhz evaluation board TQP7M9102-pcb2140 2.11?C?2.17 ghz evaluation board TQP7M9102-pcb2600 2.5 C 2.7 ghz evaluation board standard t/r size = 1000 pieces on a 7 reel rf in gnd rf out / v cc 1 2 3 backside paddle - gnd downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 2 of 26 www.qorvo.com ? recommended operating conditions parameter min typ max units device voltage (v cc) +4.75 +5 +5.25 v t case - 40 +105 c tj for >10 6 hours mttf +170 c electrical specifications are measured at specified test cond itions. specifications are not guaranteed over all recommended operating conditions. absolute maximum ratings parameter rating storage temperature -65 to 150 ? c rf input power, cw, 50, t=25c +2 7 ? dbm device voltage (v cc ) +8 ? v exceeding any one or a combination of the absolute maximu m rating conditions may cause permanent damage to the device. ext ended application of absolute maximum rating conditions to the devic e may reduce device reliability. electrical specifications parameter conditions ? (1) min typ max units operational frequency range 400 40 00 mhz test frequency 2140 mhz gain 15. 5 17.8 db input return loss 12 db output return loss 10 db output p1db +2 6.4 +27.5 dbm output ip3 pout = ?+8 dbm/tone, ?f =? 1 mhz + 41 +43.8 dbm wcdma channel power ?50? dbc aclr, note 2 +18.5 dbm noise figure 3.9 db quiescent current, i cq 115 137 155 ma thermal resistance, jc junction to case 50 c/w notes: 1. test conditions unless otherwise noted: vcc?=?+5?v, temp.?=? +25?c, matched 2140?mhz reference circuit 2. a cl r test set-up: 3gpp wcdma, tm1+64 dpch, +5 mhz offs et, par = 10.2 db at 0.01% probability performance summary table frequency 635 768 869 960 1540 1840 1960 2140 2140 2350 2600 3500 mhz gain 22.4 20.9 21.8 21.7 20.2 20.0 18.4 15.5 17.8 16.0 14.5 14.5 db input return loss 12 9 10 17 15 17 13 8 12 17 14.5 17 db output return loss 14 8 12 9 6 7.5 7 8 11 8 8 11 db output p1db +27.3 +28.4 +27.3 +27.4 +28.2 +27.5 +27.0 +30.7 +27.6 +27.2 +28.0 +26.2 dbm output ip3 +44 +44 +43 +44 +51 +42 +46 +38 +44 +44 +44 +45 dbm notes: 1. test conditions unless otherwise noted: v cc ?=?+5?v, temp.?=?+25?c, matched reference circuit 2. reference designs for the various frequencies are either included on this datasheet or may be obtained by contacting appsupport@qorvo.com downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 3 of 26 www.qorvo.com ? device characterization data note: the gain for the unmatched device in a 50 ohm system is shown as the black trace labeled "gain (s2 1)". in a circuit tuned for a particular frequency, it is expected that actual gain will be higher, up to the maximum stable gain. the maximum stable gain is shown as the red trace [gmax]. the impedance smith chart plots are shown from 0.01 to 4 ghz. s-parameters freq (mhz) s11 (db) s11 (ang) s21 (db) s21 (ang) s12 (db) s12 (ang) s22 (db) s22 (ang) 50 -2.55 176.64 20.38 156.15 -35.04 -9.37 -5.88 -159.98 100 -2.91 172.21 18.15 151.53 -35.97 -20.12 -4.45 -167.94 200 -5.79 172.18 14.52 160.74 -41.94 -60.14 -3.20 177.62 400 -1.41 -163.37 19.80 154.97 -34.61 49.55 -7.14 165.58 600 -0.52 179.77 18.56 125.67 -33.11 19.10 -6.55 178.58 800 -0.45 171.80 16.85 108.86 -32.96 8.46 -5.41 178.08 1000 -0.49 165.43 15.28 95.36 -32.92 -1.08 -4.76 174.13 1200 -0.60 160.30 13.79 85.52 -33.15 -4.65 -4.38 171.06 1400 -0.60 157.51 12.55 77.70 -33.23 -9.05 -4.24 167.58 1600 -0.67 152.76 11.49 69.57 -33.03 -15.12 -4.15 163.37 1800 -0.74 148.28 10.53 62.39 -32.96 -19.02 -4.00 159.18 2000 -0.72 143.55 9.75 54.69 -33.03 -20.90 -3.89 155.31 2200 -0.78 139.03 8.88 48.56 -32.96 -25.51 -3.77 150.66 2400 -0.71 135.24 7.99 42.25 -32.88 -27.98 -3.40 146.69 2600 -0.74 131.98 7.23 36.47 -33.43 -30.45 -3.38 144.96 2800 -0.75 128.79 6.58 31.19 -33.15 -33.43 -3.44 142.02 3000 -0.80 126.32 6.09 26.41 -33.23 -36.48 -3.50 139.73 3200 -0.75 122.75 5.69 20.73 -33.43 -37.86 -3.39 137.14 3400 -0.81 118.06 5.30 14.38 -33.39 -44.57 -3.48 130.99 3600 -0.82 113.62 4.59 7.77 -33.03 -43.44 -3.34 124.40 3800 -0.71 108.88 4.07 1.73 -32.92 -50.92 -3.04 120.16 4000 -0.68 105.86 3.64 -2.85 -33.15 -54.00 -2.92 118.44 test conditions: v cc ?=?+5 v, i cq ?=? 135 ma, temp. ?=?+25?c, unmatched 50 ohm system, reference plane at device lea ds 0 5 10 15 20 25 30 0 0.5 1 1.5 2 2.5 3 3.5 4 gain (db) frequency (ghz) gain and maximum stable gain gain (max) gain (s21) -1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 0.8 1 -1 -0.75-0.5-0.25 0 0.25 0.5 0.75 1 input smith chart 0.01 ghz 4 ghz output smith chart 0.01 ghz 4 ghz downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 4 of 26 www.qorvo.com ? 617 C 652 mhz reference design notes: 1. see evaluation board pcb information for material and stack up. 2. the recommended component values are dependent upon t he frequency of operation. 3. all components are of 0603 size unless stated on the s chematic. 4. critical component placement locations: ? distance from u1 pin pad 1 (left edge) to r1 (right edge ): 20 mils ? distance from u1 pin pad 1 (left edge) to l2 (right edge): 90 mils ? distance from u1 pin pad 1 (left edge) to c5 (right edge ): 235 mils ? distance from u1 pin pad 3 (right edge) to l3 (left edg e): 120 mils ? distance from u1 pin pad 3 (right edge) to c6 (left edge ): 255 mils typical performance 617 ?C? 652 mhz reference design test conditions unless otherwise noted: v cc =+5?v, i cq =137 ma (typ.), temp.=+25?c parameter conditions typical value units frequency 617 635 652 mhz gain 22.3 22.4 22.4 db input return loss 10 12 14 db output return loss 16 14 12 db output p1db +27.1 +2 7.3 +2 7.3 dbm output ip3 pout= +15 dbm/tone, ? f= 1 mhz +43.0 +4 3.8 +4 3.7 dbm lte chan. power (1) ?50 dbc aclr +1 5.8 +1 6.3 +1 6.5 dbm notes: 1. aclr test set-up: 1 ch, 20?mhz bw, lte e -tm1.1, 9.5 db par at 0.01% probability bill of material 617 ?C? 652 mhz reference design reference des. value description manuf. part number n/a n/a printed circuit board qorvo u1 n/a ? w high linearity amplifier qorvo TQP7M9102 c1 , c2 , c3 100 pf cap, 0603, +/-5%. 100v npo/cog various c5 12 pf cap, 0603, +/-2%. 50v. npo/cog various c6 3.9 pf cap, 0603, +/-0.1pf. 100v. npo/cog various c4 1.0 uf cap, 0603, 10%, x5r, 10v various l1 82 nh ind, 0805, 5%, ceramic coilcraft 0805cs- 82 0xjl l2 1.5 nh ind, 0603 various l3 4.7 nh ind, 0603 various r1 2.7 resistor, chip, 0603, 5%, 1/16w various j4 j3 u1 l1 c2 c3 c4 c1 r1 c5 l2 c6 l3 u1 TQP7M9102 j4 gnd j3 vcc 1 2,4 3 j1 rf input j2 rf output l1 82 nh 0805 c1 100 pf c4 1 uf c3 100 pf c2 100 pf c5 12 pf c6 3.9 pf r1 2.7 ? l3 4.7 nh l2 1.5 nh downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 5 of 26 www.qorvo.com ? performance plots 617?C?652 mhz reference design test conditions unless otherwise noted: v cc =+5v, i cq =137 ma (typ.) 19 20 21 22 23 24 617 624 631 638 645 652 gain (db) frequency (mhz) gain vs. frequency temp.=+25c -15 -10 -5 0 617 624 631 638 645 652 |s11| (db) frequency (mhz) input return loss vs. frequency temp.=+25c -20 -15 -10 -5 0 617 624 631 638 645 652 |s22| (db) frequency (mhz) output return loss vs. frequency temp.=+25c 24 25 26 27 28 29 617 624 631 638 645 652 p1db (dbm) frequency (mhz) p1db vs. frequency temp.=+25c 35 40 45 50 9 10 11 12 13 14 15 16 17 18 19 oip3 (dbm) pout/tone (dbm) oip3 vs. pout/tone TQP7M9102 652 mhz 635 mhz 617 mhz temp.=+25c -60 -55 -50 -45 -40 -35 14 15 16 17 18 19 20 aclr (dbc) pout (dbm) aclr vs. output power 652 mhz 635 mhz 617 mhz temp.=+25c lte 1ch 20mz, adj ch ibw 18.02mhz, par 9.5db no clipping downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 6 of 26 www.qorvo.com ? typical performance 746?C?768 mhz reference design test conditions unless otherwise noted: v cc =+5?v, i cq =137 ma (typ.), temp.=+25?c parameter conditions typical value units frequency 746 768 mhz gain 20.9 20.9 db input return loss 8 9 db output return loss 10 8 db output p1db +28.2 +28.4 dbm output ip3 pout= +18 dbm/tone, ? f= 1 mhz +47 +44 dbm bill of material 746?C?768 mhz reference design reference des. value description manuf. part number n/a n/a printed circuit board qorvo u1 n/a ? w high linearity amplifier qorvo TQP7M9102 c1, c2, c3 100 pf cap, 0603, +/-5%. 100v npo/cog various c5 12 pf cap, 0603, +/-2%. 50v. npo/cog various c6 4.7 pf cap, 0603, +/-0.1pf. 100v. npo/cog various c4 1.0 uf cap, 0603, 10%, x5r , 10v various l1 33 nh ind, 0805, 5%, ceramic coilcraft 0805cs- 33 0xjl l2 4.7 nh ind, 0603, +/-0.3. >5600mhz toko ll1608-fsl4n7s r1 3.0 resistor, chip, 0603, 5%, 1/16w various 746 C 768 mhz reference design notes: 5. see evaluation board pcb information for material and stack up. 6. the recommended component values are dependent upon t he frequency of operation. 7. all components are of 0603 size unless stated on the s chematic. 8. critical component placement locations: ? distance from u1 pin pad 1 (left edge) to r1 (right edge ): 0 mils ? distance from u1 pin pad 1 (left edge) to c6 (right edge ): 60 mils ? distance from u1 pin pad 1 (left edge) to c5 (right edge ): 230 mils ? distance from u1 pin pad 3 (right edge) to l2 (left edg e): 0 mils j4 j3 u1 l1 c2 c3 c4 c1 r1 c5 l2 c6 u1 TQP7M9102 j4 gnd j3 vcc 1 2,4 3 j1 rf input j2 rf output l1 0805 33 nh c1 100 pf c4 1.0 uf c3 100 pf r1 0402 3.0 ? c6 4.7 pf c2 100 pf l2 4.7 nh c5 12 pf downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 7 of 26 www.qorvo.com ? performance plots 746?C?768 mhz reference design test conditions unless otherwise noted: v cc =+5v, i cq =137 ma (typ.) 18 19 20 21 22 745 750 755 760 765 770 gain (db) frequency (mhz) gain vs. frequency temp.=+25c -15 -10 -5 0 745 750 755 760 765 770 |s11| (db) frequency (mhz) input return loss vs. frequency temp.=+25c -15 -10 -5 0 745 750 755 760 765 770 |s22| (db) frequency (mhz) output return loss vs. frequency temp.=+25c 30 35 40 45 50 15 16 17 18 19 20 21 oip3 (dbm) pout/tone (dbm) oip3 vs. pout/tone temp.=+25c 768 mhz 746 mhz downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 8 of 26 www.qorvo.com ? typical performance TQP7M9102?pcb900 test conditions unless otherwise noted: v cc =+5v, i cq =137?ma (typ.), temp.=+25?c parameter conditions typical value units frequency 869 920 960 mhz gain 21.8 21.9 21.7 db input return loss 10 16 17 db output return loss 12 10 9 db output p1db +27.3 +27.4 +27.4 dbm oip3 pout= +19 dbm/tone, f=1 mhz +42.7 +43.4 +43.9 dbm wcdma channel power (1) ?50 dbc aclr +18.0 +18.2 +18.1 dbm noise figure 5.9 5.9 5.9 db notes: 1. aclr test set-up: 3gpp wcdma, tm1+64 dpch, +5 mhz offset , par = 10.2 db at 0.01% probability 869? C?960 mhz evaluation board (TQP7M9102?pcb900) notes: 1. see evaluation board pcb information for material and stack up. 2. components shown on the silkscreen but not on the s chematic are not used. 3. the recommended component values are dependent upon t he frequency of operation. 4. all components are of 0603 size unless stated on the s chematic. 5. critical component placement locations: ? distance from u1 pin 1 (left edge) to r1 (right edge): 9 0 mils (4.3 deg. at 920 mhz) ? distance from r1 (left edge) to c5 (right edge): 70 mi ls (3.3 deg. at 920 mhz) ? distance from u1 pin 3 (right edge) to l2 (left edge): 120 mils (5.7 deg. at 920 mhz) ? distance from u1 pin 3 (right edge) to c6 (left edge): 370 mils (17.6 deg. at 920 mhz) bill of material TQP7M9102?pcb900 reference des. value description manuf. part number n/a n/a printed circuit board qorvo u1 n/a TQP7M9102 amplifier, sot-89 pkg. qorvo TQP7M9102 r1 1.8 resistor, chip, 0603, 5%, 1/16w various l2 3.3 nh inductor, 0603, +/-0.3 nh toko ll1608-fsl3n3s l1 33 nh inductor, 0805, 5%, coilcraft cs series coilcraft 0805cs-330xjlb c5 8.2 pf cap., chip, 0603, +/-0.1pf. 200v. npo/cog avx 06032u8r2bat2a c6 3.3 pf cap., chip, 0603, +/-0.1pf. 200v. npo/cog avx 06032u3r3bat2a c1, c2, c3 100 pf cap., chip, 5%, 50v, npo/cog various c4 1.0 uf cap., chip, 10%, 10v, x5r various j4 j3 u1 l1 c2 c3 c4 c1 r1 c5 l2 c6 u1 TQP7M9102 j4 gnd j3 vcc 1 2,4 3 j1 rf input j2 rf output l1 33 nh 0805 c1 100 pf c4 1 uf c3 100 pf c2 100 pf c5 8.2 pf c6 3.3 pf r1 1.8 ? l2 3.3 nh downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 9 of 26 www.qorvo.com ? performance plots TQP7M9102?pcb900 test conditions unless otherwise noted: v cc =+5v, i cq =137 ma (typ.) 19 20 21 22 23 24 860 880 900 920 940 960 gain (db) freq (mhz) gain vs. frequency +85c +25c ?40 c -25 -20 -15 -10 -5 0 860 880 900 920 940 960 |s11| (db) freq (mhz) input return loss vs. frequency +85c +25c ?40 c -25 -20 -15 -10 -5 0 860 880 900 920 940 960 |s22| (db) freq (mhz) output return loss vs. frequency +85c +25c ?40 c - 65 - 60 - 55 - 50 - 45 - 40 - 35 12 13 14 15 16 17 18 19 20 aclr (dbc) pout (dbm) aclr vs. output power +85 c +25 c ?40 c w-cdma 3gpp test model 1+64 dpch par = 10.2 db @ 0.01% probability 3.84 mhz bw freq.=920 mhz 36 38 40 42 44 46 11 13 15 17 19 21 oip3 (dbm) pout/tone (dbm) oip3 vs. pout/tone +85 c +25 c ?40 c freq.=920 mhz 1 mhz tone spacing 25 26 27 28 29 30 860 880 900 920 940 960 p1db (dbm) frequency (mhz) p1db vs. frequency ?40 c +25 c +85 c - 65 - 60 - 55 - 50 - 45 - 40 - 35 12 13 14 15 16 17 18 19 20 aclr (dbc) pout (dbm) aclr vs. output power 960 mhz 920 mhz 869 mhz w-cdma 3gpp test model 1+64 dpch par = 10.2 db @ 0.01% probability 3.84 mhz bw temp.=+25 c 30 35 40 45 50 11 13 15 17 19 21 oip3 (dbm) pout/tone (dbm) oip3 vs. pout/tone 960 mhz 920 mhz 869 mhz 1 mhz tone spacing temp.=+25 c 19 21 23 25 27 29 -3 -1 1 3 5 7 pout (dbm) pin (dbm) output power vs. input power ?40 c +25 c +85 c freq.= 920 mhz 120 140 160 180 200 220 240 260 12 14 16 18 20 22 24 26 28 icc (ma) pout (dbm) icc vs. output power +85c +25c ?40 c frequency = 920 mhz downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 10 of 26 www.qorvo.com ? bill of material 700?C?1000?mhz reference design reference des. value description manuf. part number n/a n/a printed circuit board qorvo u1 n/a ? w high linearity amplifier qorvo TQP7M9102 c1,c2,c3 100?pf 0603, 5%, 50?v, npo/cog various c4 0.1?f 0603, 10%, 50?v, x7r various c5 1.0?f 0603. 10%, 10?v, x5r various ll -1608-fsl1n2s l1 33?nh 0805, 5%, cer core,0805 coilcraft coilcraft 0805cs- 33 0xjl l2 5.6?nh 0603, ?0.3?nh, multilayer, toko toko ll1608-fsl5n6s l3 2.7?nh 0603, ?0.3?nh, multilayer, toko toko ll1608-fsl2n7s c6 4.7?pf 0603, ?0.1?pf, 200?v, npo/cog, avx u series avx 06032u4r7bat2a c7 12?pf 0603, 2%, 50?v, npo/cog various c8 3.3?pf 0603, ?0.1?pf, 200?v, npo/cog, avx u series avx 06032u3r3bat2a 700? C?1000?mhz reference design notes: 1. the recommended component values are dependent upon the freq uency of operation. 2. all components are of 0603 size unless stated on the schematic . 3. entire bias network values are critical of linearity performance. 4. critical component placement locations: distance from u1 pin 1 (left edge) to r1 (right edge): 10 mils (0.5 deg at 920 mhz) distance from r1 (left edge) to c7 (right edge): 10 mils (0.5 deg at 920 mhz ) distance from c7 (left edge) to l2 (right edge): 10 mils (0.5 deg at 920 m hz) distance from l2 (left edge) to c6 (right edge): 20 mils (1.0 deg at 920 mhz ) distance from u1 pin 3 (right edge) to l3 (left edge): 290 mils (13.8 deg at 9 20 mhz) distance from l3 (right edge) to c8 (left edge): 20 mils (1.0 deg at 920 m hz) j4 j3 u1 l2 c7 c8 l1 c2 c3 c4 c1 r1 c6 l3 c5 u1 TQP7M9102 j4 gnd j3 vcc 1 2,4 3 c7 12.0 pf j1 rf input j2 rf output l1 33 nh 0805 c5 1.0 uf c3 100 pf r1 1.2 ? ???? c8 3.3 pf c2 100 pf c1 100 pf c6 4.7 pf l2 5.6 nh l3 2.7 nh c4 0.1 uf downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 11 of 26 www.qorvo.com ? performance plots 700?C?1000?mhz reference design test conditions unless otherwise noted: v cc =+5?v, i cq =137 ma (typ.), temp.=+25?c typical performance 700? C?1000?mhz reference design test conditions unless otherwise noted: v cc? =?+5??v, i cq =135?ma , temp?=?+25?c, 50? system parameter conditions typical value units frequency 700 850 1000 mhz gain 22.2 21.8 21.1 db input return loss 6.3 7.7 7.2 db output return loss 18.8 14.2 15.2 db output p1db +27.4 +28 +28.3 dbm output ip3 pout= +16 dbm?/?tone, ? f= 1 mhz +42.3 +43 +41.3 dbm 19 20 21 22 23 24 700 750 800 850 900 950 1000 gain (db) frequency (mhz) gain vs. frequency -20 -15 -10 -5 0 700 750 800 850 900 950 1000 return loss (db) frequency (mhz) return loss vs. frequency input return loss output return loss 30 35 40 45 50 11 13 15 17 19 21 oip3 (dbm) pout/tone (dbm) oip3 vs. pout/tone 700 mhz 850 mhz 1000 mhz 25 26 27 28 29 30 700 750 800 850 900 950 1000 p1db (dbm) frequency (mhz) p1db vs. frequency downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 12 of 26 www.qorvo.com ? bill of material 1800?C?2200 mhz 1 watt reference design reference des. value description manuf. part number n/a n/a printed circuit board qorvo u1 n/a ? w high linearity amplifier qorvo TQP7M9102 c2 , c3 22 pf cap, 0603, +/-1%. 200v npo/cog various c1, c5 1.5 pf cap, 0603, +/-0.1pf. 200v. npo/cog various l2 2.2 nh ind, chip, 0603, +/-0.3nh >6000mhz toko ll -1608-fsl1n2s c4 1.0 uf cap, 0603, 10%, x5r , 10v various l1 18 nh ind, 0805, 5%, ceramic coilcraft 0805cs- 18 0xjl c6 1.8pf cap, 0603, +/-0.1pf. 200v. npo/cog various r1 2.7 res, 0603, 5% various typical performance 1800?C?2200 mhz 1 watt reference design test conditions unless otherwise noted: v cc =+5v, i cq =137 ma (typ.), temp= +25c parameter conditions typical value units frequency 1800 2000 2200 mhz gain 15.3 15.5 15.4 db input return loss 7.5 8 9 db output return loss 7 8 8 db output p1db +29.7 +30.7 +29.9 dbm output ip3 pout= +15 dbm/tone, ? f= 1 mhz +38 +38 +38 dbm 1800? C?2200 mhz 1?watt reference design notes: 1. see evaluation board pcb information for material and stack up. 2. components shown on the silkscreen but not on the s chematic are not used. 3. 0 resistors (r2) may be replaced with copper trace in th e target application layout. 4. the recommended component values are dependent upon t he frequency of operation. 5. all components are of 0603 size unless stated on the schematic. 6. critical component placement locations: ? distance from u1 pin 1 (left edge) to r1 (right edge): 2 5 mils ? distance from u1 pin 1 (left edge) to c1 (right edge): 1 45 mils ? distance from u1 pin 1 (left edge) to c5 (right edge): 9 0 mils ? distance from u1 pin 3 (right edge) to c6 (left edge): 145 mils j4 j3 u1 c6 l1 c2 c3 l2 c5 c4 r1 c1 u1 TQP7M9102 j4 gnd j3 +5v 1 2,4 3 c5 1.5 pf j1 rf input j2 rf output l1 18 nh (0805) c2 22 pf c1 1.5 pf c4 1.0 uf c6 1.8 pf c3 22 pf r1 2.7 ? l2 2.2 nh downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 13 of 26 www.qorvo.com ? performance plots 1800?C?2200 mhz 1 watt reference design test conditions unless otherwise noted: v cc =+5?v, i cq =137 ma (typ.), temp.=+25?c 10 12 14 16 18 20 1800 1900 2000 2100 2200 gain (db) frequency (mhz) gain vs. frequency temp.=+25c -25 -20 -15 -10 -5 0 1800 1900 2000 2100 2200 |s11| (db) frequency (mhz) input return loss vs. frequency temp.=+25c temp.=+25c -20 -15 -10 -5 0 1800 1900 2000 2100 2200 |s22| (db) frequency (mhz) output return loss vs. frequency temp.=+25c 25 30 35 40 45 9 10 11 12 13 14 15 16 17 18 19 oip3 (dbm) pout/tone (dbm) oip3 vs. pout/tone temp.=+25c 2200 mhz 2050 mhz 1900 mhz 1800 mhz downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 14 of 26 www.qorvo.com ? typical performance TQP7M9102?pcb2140 test conditions unless otherwise noted: v cc =+5?v, i cq =137 ma (typ.), temp=+25?c parameter conditions typical value units frequency 2110 2140 2170 mhz gain 17.9 17.8 17.7 db input return loss 12 12 11 db output return loss 12 11 10 db output p1db +27.8 +27.6 +27.4 dbm oip3 pout= +9 dbm/tone, f=1 mhz +43.6 +43.5 +43.6 dbm wcdma channel power (1) ?50 dbc aclr +18.5 +18.4 +18.3 dbm noise figure 3.8 3.9 4.0 db notes: 1. aclr test set-up: 3gpp wcdma, tm1+64 dpch, +5 mhz offse t, par = 10.2 db at 0.01% prob 2110? C?2170 mhz evaluation board (TQP7M9102?pcb2140) notes: 1. see evaluation board pcb information for material and stack up. 2. components shown on the silkscreen but not on the s chematic are not used. 3. the recommended component values are dependent upon t he frequency of operation. 4. all components are of 0603 size unless stated on the s chematic. 5. critical component placement locations: ? distance from u1 pin 1 (left edge) to c5 (right edge): 3 5 mils (3.9 deg. at 2140 mhz) ? distance from u1 pin 1 (left edge) to c1 (right edge): 9 0 mils (9.9 deg. at 2140 mhz) ? distance from u1 pin 3 (right edge) to c6 (left edge): 210 mils (23.2 deg. at 2140 mhz) bill of material TQP7M9102?pcb2140 reference des. value description manuf. part number n/a n/a printed circuit board qorvo u1 n/a TQP7M9102 amplifier, sot-89 pkg. qorvo TQP7M9102 r1 39 pf cap., chip, 0603, +/-1%. 200v npo/cog various l1 18 nh inductor, 0805, coilcraft cs series coilcraft 0805cs-180xjlb c1 1.5 pf cap., chip, 0603, +/-0.1pf. 200v. npo/cog various 06032u1r5bat2a c2 3.3 pf cap., chip, 0603, +/-0.1pf. 200v. npo/cog various 06032u3r3bat2a c3 22 pf cap., chip, 5%, 50v, npo/cog various c4 1.0 uf cap., chip, 10%, 10v, x5r various c5 1.8 pf cap., chip, 0603, +/-0.1pf. 200v. npo/cog various 06032u1r8bat2a c6 0.8 pf cap., chip, 0603, +/-0.05pf, 50v various 06032u0r8bat2a j4 j3 u1 l1 c2 c3 c4 r1 c1 c5 c6 u1 TQP7M9102 j4 gnd j3 vcc 1 2,4 3 c5 1.8 pf j1 rf input j2 rf output l1 18 nh c2 3.3 pf c1 1.5 pf c4 1.0 uf c3 22 pf c6 0.8 pf r1 39 pf downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 15 of 26 www.qorvo.com ? performance plots TQP7M9102?pcb2140 test conditions unless otherwise noted: v cc =+5?v, i cq =137 ma (typ.) 15 16 17 18 19 20 2110 2120 2130 2140 2150 2160 2170 gain (db) freq (mhz) gain vs. frequency +105c +85c +25c ?40 c -20 -15 -10 -5 0 2110 2120 2130 2140 2150 2160 2170 |s11| (db) freq (mhz) input return loss vs. frequency +105c +85c +25c ?40 c -20 -15 -10 -5 0 2110 2120 2130 2140 2150 2160 2170 |s22| (db) freq (mhz) output return loss vs. frequency +105c +85c +25c ?40 c - 65 - 60 - 55 - 50 - 45 - 40 - 35 14 15 16 17 18 19 20 aclr (dbc) pout (dbm) aclr vs. output power +85 c +25 c ?40 c w-cdma 3gpp test model 1+64 dpch par = 10.2 db @ 0.01% probability 3.84 mhz bw freq.= 2140 mhz 38 40 42 44 46 7 9 11 13 15 17 oip3 (dbm) pout/tone (dbm) oip3 vs. pout/tone freq.=2140 mhz 1 mhz tone spacing +105c +85c +25c ?40 c 25 26 27 28 29 30 2110 2120 2130 2140 2150 2160 2170 p1db (dbm) frequency (mhz) p1db vs. frequency +105c +85c +25c ?40 c - 65 - 60 - 55 - 50 - 45 - 40 - 35 14 15 16 17 18 19 20 aclr (dbc) pout (dbm) aclr vs. output power 2170 mhz 2140 mhz 2110 mhz w-cdma 3gpp test model 1+64 dpch par = 10.2 db @ 0.01% probability 3.84 mhz bw temp.=+25 c 30 35 40 45 50 7 9 11 13 15 17 oip3 (dbm) pout/tone (dbm) oip3 vs. pout/tone 2170 mhz 2140 mhz 2110 mhz 1 mhz tone spacing temp.=+25 c 19 21 23 25 27 29 2 4 6 8 10 12 pout (dbm) pin (dbm) output power vs. input power freq.=2140 mhz +105c +85c +25c ?40 c -65 -60 -55 -50 -45 -40 -35 14 15 16 17 18 19 20 aclr (dbc) pout (dbm) aclr vs output power temp.=+25c 2170 mhz 2140 mhz 2110 mhz lte 1ch 20mhz, adj ch ibw 18.02mhz, par 9.5db no clipping 120 140 160 180 200 220 240 260 12 14 16 18 20 22 24 26 28 icc (ma) pout (dbm) icc vs. output power frequency = 2140 mhz +105c +85c +25c ?40 c -65 -60 -55 -50 -45 -40 -35 14 15 16 17 18 19 20 aclr (dbc) pout (dbm) aclr vs output power freq = 2140 mhz lte 1ch 20mhz, adj ch ibw 18.02mhz, par 9.5db no clipping +105c +85c +25c ?40 c downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 16 of 26 www.qorvo.com ? 2300? C?2700 mhz reference design notes: 1. see evaluation board pcb information for material and stack up. 2. components shown on the silkscreen but not on the schematic ar e not used. 3. 0 resistors (r2) may be replaced with copper trace in the target application layout. 4. the recommended component values are dependent upon the freq uency of operation. 5. all components are of 0603 size unless stated on the schematic . 6. critical component placement locations: distance from u1 pin 1 (left edge) to r1 (right edge): 10 mils distance from u1 pin 1 (left edge) to c1 (right edge): 80 mils distance from u1 pin 1 (left edge) to c5 (right edge): 235 mils distance from u1 pin 3 (right edge) to c6 (left edge): 165 mils bill of material 2300 C 2700 reference design reference des. value description manuf. part number n/a n/a printed circuit board qorvo u1 n/a ? w high linearity amplifier qorvo TQP7M9102 c1 1.8 pf cap, 0603, 0.05 pf, 50v, accu-p avx 06035j1r8abstr c5 1.5 pf cap, 0603, 0.05 pf, 50v, accu-p avx 06035j1r5abstr c2, c3 22 pf cap, 0603, 5%, 50v, npo/cog various c4 1.0 uf cap, 0603, 10%, x5r , 10v various c6 0.9 pf cap, 0603 avx 06035j0r9abstr r1 2.2?? res, 0402 various r2 0 ? res, 0603, 5%, 1/16w, chip various l1 18 nh ind, 0805, 5%, ceramic coilcraft 0805cs-180xjl j4 j3 u1 c6 l1 c2 c3 r2 c5 c4 r1 c1 u1 TQP7M9102 j4 gnd j3 +5v 1 2,4 3 c5 1.5 pf j1 rf input j2 rf output l1 18 nh (0805) c2 22 pf c1 1.8 pf c4 1.0 uf c6 0.9 pf c3 22 pf r1 2.2 ? ?????? downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 17 of 26 www.qorvo.com ? typical performance 2300 C 2700 reference design test conditions unless otherwise noted: v cc =+5?v, i cq =137 ma (typ.), temp=+25?c parameter conditions typical value units frequency 2300 2500 2700 mhz gain 13.8 14.7 13.6 db input return loss 5.5 13.3 7.9 db output return loss 12.6 12 10.6 db output p1db +27.7 +27.8 +27.1 dbm oip3 pout= +9 dbm?/?tone, f?=?1?mhz +43.8 +44.0 +45.9 dbm performance plots 2300 C 2700 reference design test conditions unless otherwise noted: v cc =+5?v, i cq =137 ma (typ.), temp.=+25?c 11 12 13 14 15 16 2300 2400 2500 2600 2700 gain (db) frequency (mhz) gain vs. frequency temp.=+25c -20 -15 -10 -5 0 2300 2400 2500 2600 2700 |s11| (db) frequency (mhz) input return loss vs. frequency temp.=+25c -15 -10 -5 0 2300 2400 2500 2600 2700 |s22| (db) frequency (mhz) output return loss vs. frequency temp.=+25c 35 40 45 50 9 11 13 15 17 19 oip3 (dbm) pout / tone (dbm) oip3 vs. pout / tone 2300 mhz 2500 mhz 2700 mhz temp.=+25c downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 18 of 26 www.qorvo.com ? bill of material TQP7M9102?pcb2600 reference des. value description manuf. part number n/a n/a printed circuit board qorvo u1 n/a ? w high linearity amplifier qorvo TQP7M9102 c1 1.8 pf cap, 0603, 0.05 pf, 50v, accu-p avx 06035j1r8abstr c5 1.5 pf cap, 0603, 0.05 pf, 50v, accu-p avx 06035j1r5abstr c2, c3 22 pf cap, 0603, 5%, 50v, npo/cog various c4 1.0 uf cap, 0603, 10%, x5r , 10v various c6 0.6 pf cap, 0603, 0.05 pf, 50v, accu-p avx 06035j0r6abstr r1 1.0 ? res, 0402, 1%, 1/16w. chip. various r2 0 ? res, 0603, 5%, 1/16w, chip various l1 18 nh ind, 0805, 5%, ceramic coilcraft 0805cs-180xjl typical performance TQP7M9102?pcb2600 test conditions unless otherwise noted: v cc =+5?v, i cq =137 ma (typ.), temp.=+25?c parameter conditions typical value units frequency 2500 2600 2700 mhz gain 14.3 14.5 14.1 db input return loss 8.5 14.5 12 db output return loss 8.5 8 7.5 db output p1db +28.0 +28.0 +28.0 dbm oip3 pout= +11 dbm/tone, f=1 mhz +44.0 +43.7 +43.0 dbm wcdma channel power (1) ?50 dbc aclr +17.5 +17.5 +17.5 dbm notes: 1. aclr test set-up: 3gpp wcdma, tm1+64 dpch, +5 mhz offse t, par = 10.2 db at 0.01% prob. 2.5?C?2.7 ghz evaluation board (TQP7M9102?pcb2600) notes: 1. see evaluation board pcb information for material and stack up. 2. components shown on the silkscreen but not on the s chematic are not used. 3. 0 resistors (r2) may be replaced with copper trace in the target applicat ion layout. 4. the recommended component values are dependent upon t he frequency of operation. 5. all components are of 0603 size unless stated on the s chematic. 6. critical component placement locations: ? distance from u1 pin 1 (left edge) to r1 (right edge): 1 3 mils ? distance from u1 pin 1 (left edge) to c1 (right edge): 7 0 mils ? distance from u1 pin 1 (left edge) to c5 (right edge): 1 48 mils ? distance from u1 pin 3 (right edge) to c6 (left edge): 78 mils j4 j3 u1 c6 l1 c2 c3 r2 c5 c4 r1 c1 u1 TQP7M9102 j4 gnd j3 +5v 1 2,4 3 c5 1.5 pf j1 rf input j2 rf output l1 18 nh (0805) c2 22 pf c1 1.8 pf c4 1.0 uf c6 0.6 pf c3 22 pf r1 1.0 ? ?????? downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 19 of 26 www.qorvo.com ? performance plots TQP7M9102?pcb2600 test conditions unless otherwise noted: v cc =+5?v, i cq =137 ma (typ.), temp.=+25?c 10 11 12 13 14 15 16 17 2300 2400 2500 2600 2700 2800 2900 gain (db) frequency (mhz) gain vs. frequency temp.=+25c -20 -15 -10 -5 0 2300 2400 2500 2600 2700 2800 2900 |s11| (db) frequency (mhz) input return loss vs. frequency temp.=+25c -20 -15 -10 -5 0 2300 2400 2500 2600 2700 2800 2900 |s22| (db) frequency (mhz) output return loss vs. frequency temp.=+25c 25 26 27 28 29 30 2500 2550 2600 2650 2700 p1db (dbm) frequency (mhz) p1db vs. frequency temp.=+25c 30 35 40 45 50 8 9 10 11 12 13 14 15 oip3 (dbm) pout/tone (dbm) oip3 vs. pout/tone temp.=+25c 2700 mhz 2600 mhz 2500 mhz -65 -60 -55 -50 -45 -40 -35 11 12 13 14 15 16 17 18 19 20 21 aclr (dbc) pout (dbm) aclr vs. output power temp.=+25c 2700 mhz 2600 mhz 2500 mhz wcdma test model 1+64 channels, par=10.3db @ .01% probability, 3.84mhz bw, 5mhz offset downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 20 of 26 www.qorvo.com ? bill of material 3400?C?3600 mhz reference design reference des. value description manuf. part number n/a n/a printed circuit board qorvo u1 n/a 0.25 w high linearity amplifier qorvo TQP7M9102 r2 0 res , 0603, 5pct. 1/16w. chip various c1 , c6 0.7 pf cap, 0603, 0.1 pf, 50v various c5 0.8 pf cap, 0603, 0.1 pf, 50v various c2 , c3 22 pf cap, 0603, 5%, 50v, npo/cog various c4 1.0 uf cap, 0603, 10%, x5r , 10v various l1 18 nh inductor, 0805, 5%, coilcraft cs series coilcraft 0805cs-180xjlb typical performance 3400?C?3600 mhz reference design test conditions unless otherwise noted: v cc =+5v, i cq =137 ma (typ.), temp.=+25c parameter conditions typical value units frequency 3400 3500 3600 mhz gain 14.2 14.5 13.8 db input return loss 9 17 9 db output return loss 15 11 8 db output p1db +27.1 +26.7 +26.2 dbm oip3 pout= +11 dbm/tone, f=1 mhz +43.3 +44.6 +44.6 dbm wcdma channel power (1) ?50 dbc aclr +18.0 +17.5 +17.0 dbm notes: 1. aclr test set-up: 3gpp wcdma, tm1+64 dpch, +5 mhz offse t, par = 10.2 db at 0.01% prob 3400? C?3600 mhz reference design notes: 7. see evaluation board pcb information for material and stack up. 8. components shown on the silkscreen but not on the s chematic are not used. 9. 0 resistors (r2) may be replaced with copper trace in th e target application layout. 10. the recommended component values are dependent upon t he frequency of operation. 11. all components are of 0603 size unless stated on the s chematic. 12. critical component placement locations: ? distance from u1 pin 1 (left edge) to c1 (right edge): 8 7 mils ? distance from u1 pin 1 (left edge) to c5 (right edge): 2 10 mils ? distance from u1 pin 3 (right edge) to c6 (left edge): 105 mils j4 j3 u1 c6 l1 c2 c3 r2 c5 c4 c1 u1 TQP7M9102 j4 gnd j3 +5v 1 2,4 3 c5 0.8 pf j1 rf input j2 rf output l1 18 nh (0805) c2 22 pf c1 0.7 pf c4 1.0 uf c6 0.7 pf c3 22 pf r2 0 ? downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 21 of 26 www.qorvo.com ? performance plots 3400?C?3600 mhz reference design test conditions unless otherwise noted: v cc =+5?v, i cq =137 ma (typ.), temp=+25c 12 13 14 15 16 3400 3450 3500 3550 3600 gain (db) frequency (mhz) gain vs. frequency temp.=+25c -20 -15 -10 -5 0 3400 3450 3500 3550 3600 |s11| (db) frequency (mhz) input return loss vs. frequency temp.=+25c -20 -15 -10 -5 0 3400 3450 3500 3550 3600 |s22| (db) frequency (mhz) output return loss vs. frequency temp.=+25c 30 35 40 45 50 9 10 11 12 13 14 15 16 17 18 19 oip3 (dbm) pout/tone (dbm) oip3 vs. pout/tone TQP7M9102 3600 mhz 3500 mhz 3400 mhz temp.=+25c -60 -55 -50 -45 -40 -35 -30 11 12 13 14 15 16 17 18 19 20 21 aclr (dbc) pout (dbm) acrl vs. pout 3600 mhz 3500 mhz 3400 mhz temp.=+25c wcdma test model 1+64 channels, par=10.3db @ .01% probability, 3.84mhz bw, 5mhz offset 22 23 24 25 26 27 28 29 3400 3450 3500 3550 3600 p1db (dbm) frequency (mhz) p1db vs. frequency temp.=+25c downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 22 of 26 www.qorvo.com ? application note?? 1.8-2.2 ghz (1/2 watt - 1 watt) tunable reference design this application note describes the ability to take the TQP7M9102 1.8-2.2 ghz design and tune it from 1/2 watt to 1 watt simply by changing the output match (one component). by use of load-pull data we were able to see the capability of this part to be tuned from +27 dbm p1db to +30 dbm by trading off oip3 performance. this gives th e end user the option to run the TQP7M9102 as a 1 watt device over a wide frequency band. below are the different reference design options which show the performance trade-offs betw een p1db and oip3 by changing the value and placement of c6. evaluation board notes: 1. all components are of 0603 size unless stated on the s chematic. 2. the recommended component values are dependent upon t he frequency of operation. 3. critical component placement locations: ? distance between u1 pin 1 pad to r1 (right edge): 10 mi l ? distance between u1 pin 1 pad to c1 (right edge): 110 mil ? distance between u1 pin 1 pad to c5 (right edge): 65 mi l ? distance between u1 pin 3 pad to c6 (left edge): see b elow: component placement option p1db c6 value (pf) line length (mils) electrical length at 2 ghz (degrees) 1 30.0 2.0 145 15.0 2 29.0 1.8 170 17.6 3 28.0 1.2 230 23.8 4 27.0 0.8 290 30.0 j4 j3 u1 c6 l1 c2 c3 l2 c5 c4 r1 c1 j1 j2 u1 TQP7M9102 j4 gnd j3 +5v 1 2,4 3 c5 1.5 pf j1 rf input j2 rf output l1 18 nh (0805) c2 22 pf c1 1.8 pf c4 1.0 uf c6 0.8 - 2.0 pf c3 22 pf r1 2.7 ? l2 2.2 nh downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 23 of 26 www.qorvo.com ? performance plots 1.8-2.2 ghz (1/2 watt - 1 watt) tunable reference design test conditions unless otherwise noted: v cc =+5?v, i cq =137 ma (typ.), temp=+25c 13 14 15 16 17 1800 1900 2000 2100 2200 gain (db) frequency (mhz) gain vs. frequency temp.=+25c option 1 option 2 option 3 option 4 -20 -15 -10 -5 0 1800 1900 2000 2100 2200 input return loss (db) frequency (mhz) input return loss vs. frequency temp.=+25c option 1 option 2 option 3 option 4 -20 -15 -10 -5 0 1800 1900 2000 2100 2200 output return loss (db) frequency (mhz) output return loss vs. frequency temp.=+25c option 1 option 2 option 3 option 4 35 40 45 50 55 9 10 11 12 13 14 15 16 17 18 19 oip3 (dbm) pout/tone (dbm) oip3 vs. pout/tone TQP7M9102 temp.=+25c option 1 option 2 option 3 option 4 freq = 1805 mhz 35 40 45 50 55 9 10 11 12 13 14 15 16 17 18 19 oip3 (dbm) pout/tone (dbm) oip3 vs. pout/tone TQP7M9102 temp.=+25c option 1 option 2 option 3 option 4 freq = 1960 mhz 35 40 45 50 55 9 10 11 12 13 14 15 16 17 18 19 oip3 (dbm) pout/tone (dbm) oip3 vs. pout/tone TQP7M9102 temp.=+25c option 1 option 2 option 3 option 4 freq = 2170 mhz 25 26 27 28 29 30 31 1800 1900 2000 2100 2200 p1db (dbm) frequency (mhz) p1db vs. frequency option 1 option 2 option 3 option 4 temp.=+25c downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 24 of 26 www.qorvo.com ? evaluation board pcb information pc board layout pcb material (stackup): 1 oz. cu top layer 0.014 inch nelco n-4000- 13, r =3.7 1 oz. cu middle layer 1 core nelco n-4000- 13 1 oz. cu middle layer 2 0.014 inch nelco n-4000- 13 1 oz. cu bottom layer finished board thickness is 0.062.006 50 ohm line dimensions: width = .028, spacing = .028. the pad pattern shown has been developed and tested for optimized assembly at qorvo. the pcb land pattern has been developed to accommodate lead and package tolerances. since surface mount processes vary from supplier to supplier, careful process development is recommended. pin configuration and description pin no. label description 1 rf in rf input. external dc block required. requires conjugate match for optimal performance. 2, backside paddle gnd rf/dc ground. use recommended via pattern to minimize inductance and thermal resistance. see pcb mounting pattern for suggested footprint. 3 rf out?/?v cc rf output, matched to 50 ohms. external dc block and bias voltage required. rf in gnd rf out / v cc 1 2 3 backside paddle - gnd downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 25 of 26 www.qorvo.com ? package marking and dimensions package marking product id: 7m9102 trace code : x xxx notes: 1. the terminal #1 identifier and terminal numbering conform to jesd 9 5-1 spp- 012. 2. trace code up to 4 characters to be assigned by sub-contractor pcb mounting pattern notes: 1. all dimensions are in millimeters. angles are in degrees. 2. use 1 oz. copper minimum for top and bottom layer metal. 3. via holes are required under the backside paddle of this devi ce for proper rf/dc grounding and thermal dissipation. 4. do not remove or minimize via hole structure in the pcb. thermal and rf gro unding is critical. 5. we recommend a 0.35mm (#80/.0135") diameter bit fo r drilling via holes and a final plated thru diameter of 0.25 mm (0.10). 6. ensure good package backside paddle solder attach for best el ectrical and thermal performance. downloaded from: http:///
TQP7M9102 1/2 w high linearity amplifier datasheet december 26, 2017 | subject to change without notice 26 of 26 www.qorvo.com ? handling precautions parameter rating standard caution! esd -sensitive device esd?C?human body model (hbm) class 2 esda?/?jedec js - 00 1- 20 14 esd?C?charged device model ( cd m) class c3 esda / jedec js -002-2014 msl?C?moisture sensitivity level level 1 ipc/jedec j-std- 020 solderability compatible with lead-free (260c max. reflow temp.) soldering process. solder profiles available upon request. contact plating: annealed matte tin or nickel palladium gold (nipdau) rohs compliance this part is compliant with 2011/65/eu rohs directive (restrictions on the use of cert ain hazardous substances in electrical and electronic equipment) as amended by directive 2015/863/eu. this product also has the following attributes: ? lead free ? halogen free (chlorine, bromine) ? antimony free ? tbbp-a (c 15 h 12 br 4 0 2 ) free ? pfos free ? svhc free contact information for the latest specifications, additional product information, worl dwide sales and distribution locations: web: www.qorvo.com tel: 1- 844 -890-8163 email: customer.support@qorvo.com for technical questions and application information: email: appsupport@qorvo.com important notice the information contained herein is believed to be reli able; however, qorvo makes no warranties regarding the informa tion contained herein and assumes no responsibility or liability whatsoe ver for the use of the information contained herein. all infor mation contained herein is subject to change without notice. customers shoul d obtain and verify the latest relevant information before pl acing orders for qorvo products. the information contained herein or any u se of such information does not grant, explicitly or imp licitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anythin g described by such information. this information does not constitute a warranty with respect to the products described herein, and qorvo hereby disclaims any and all warranties with respect to such products whether express or implied by law, course of dealing, course of performance, usage of trade or otherwise, including the implied warranties of merchantability and fitness for a particular purpose. without limiting the generality of the foregoing, qorvo pro ducts are not warranted or authorized for use as critical compo nents in medical, life-saving, or life-sustaining applications, or other appl ications where a failure would reasonably be expected to cause severe personal injury or death. copyright 2017 ? qorvo, inc. | qorvo is a registered trademark of qorvo, in c. pb downloaded from: http:///

▲Up To Search▲

Price & Availability of TQP7M9102

	To Download TQP7M9102 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .