View EL5364IUZ-T13_9102639.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 ? fn7389.3 caution: these devices are sensitive to electrosta tic discharge; follow proper ic handling procedures. 1-888-intersil or 321-724-7143 | intersil (and design) is a registered trademark of intersil americas inc. copyright ? intersil americas inc. 2002-2004. all rights reserved. elantec is a registered trademark of elantec semiconductor, inc. all other trademarks mentioned are the property of their respective owners. el5164, el5165, el5364 600mhz current feedback amplifiers with enable the el5164, el5165, and el5364 are current feedback amplifiers with a very high bandwidth of 600mhz. this makes these amplifiers ideal for today?s high speed video and monitor applications. with a supply current of just 5ma and the ability to run from a single supply voltage from 5v to 12v, the amplifiers are also ideal for hand held, portable or battery-powered equipment. the el5164 also incorporates an enable and disable function to reduce the supply current to 100a typical per amplifier. allowing the ce pin to float or applying a low logic level will enable the amplifier. the el5165 is offered in the 5-pin sot-23 package, el5164 is available in the 6-pin sot-23 and the industry-standard 8- pin so packages, and the el5364 in a 16-pin so and 16-pin qsop packages. all operate over the industrial temperature range of -40c to +85c. features ? 600mhz -3db bandwidth ? 4700v/s slew rate ? 5ma supply current ? single and dual supply operation, from 5v to 12v supply span ? fast enable/disable (el5164 & el5364 only) ? available in sot-23 packages ? dual (el5264 & el5265) and triple (el5362 & el5363) also available ? high speed, 1ghz product available (el5166 & el5167) ? 300mhz product available (el5162 family) ? pb-free available applications ? video amplifiers ? cable drivers ? rgb amplifiers ? test equipment ? instrumentation ? current to voltage converters ordering information part number package tape & reel pkg. dwg. # el5164is 8-pin so - mdp0027 el5164is-t7 8-pin so 7? mdp0027 el5164is-t13 8-pin so 13? mdp0027 el5164iw-t7 6-pin sot-23 7? (3k pcs) mdp0038 el5164iw-t7a 6-pin sot-23 7? (250 pcs) mdp0038 el5165iw-t7 5-pin sot-23 7? (3k pcs) mdp0038 el5165iw-t7a 5-pin sot-23 7? (250 pcs) mdp0038 el5165ic-t7 5-pin sc-70 7? (3k pcs) p5.049 el5165ic-t7a 5-pin sc-70 7? (250 pcs) p5.049 el5364is 16-pin so (0.150?) - mdp0027 el5364is-t7 16-pin so (0.150?) 7? mdp0027 el5364is-t13 16-pin so (0.150?) 13? mdp0027 el5364iu 16-pin qsop - mdp0040 el5364iu-t7 16-pin qsop 7? mdp0040 el5364iu-t13 16-pin qsop 13? mdp0040 el5364iuz (see note) 16-pin qsop (pb-free) - mdp0040 el5364iuz-t7 (see note) 16-pin qsop (pb-free) 7? mdp0040 el5364iuz- t13 (see note) 16-pin qsop (pb-free) 13? mdp0040 note: intersil pb-free products employ special pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which is compatible with both snpb and pb-free soldering operations. intersil pb-free products are msl classified at pb-free peak reflow temperatures that meet or exceed the pb-free requirements of ipc/jedec j std-020b. data sheet june 22, 2004
2 pinouts el5164 (8-pin so) top view el5165 (5-pin sot-23, sc-70) top view el5364 (16-pin so, qsop) top view el5164 (6-pin sot-23) top view 1 2 3 4 8 7 6 5 - + nc in- in+ vs- ce vs+ out nc 1 2 3 5 4 - + out vs- in+ vs+ in- 1 2 3 4 16 15 14 13 5 6 7 12 11 10 8 9 - + - + - + ina+ cea vs- ceb inb+ nc cec inc+ ina- outa vs+ outb inb- nc outc inc- 1 2 3 6 4 - + out vs- in+ vs+ in- 5ce el5164, el5165, el5364
3 absolute maxi mum ratings (t a = 25c) supply voltage between v s + and v s - . . . . . . . . . . . . . . . . . . . 13.2v maximum continuous output current . . . . . . . . . . . . . . . . . . . 50ma pin voltages . . . . . . . . . . . . . . . . . . . . . . . . . v s - -0.5v to v s + +0.5v operating junction temperature . . . . . . . . . . . . . . . . . . . . . . . 125c power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see curves storage temperature . . . . . . . . . . . . . . . . . . . . . . . .-65c to +150c ambient operating temperature . . . . . . . . . . . . . . . .-40c to +85c caution: stresses above those listed in ?absolute maximum ratings? may cause permanent damage to the device. this is a stress o nly rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. important note: all parameters having min/max specifications are guaranteed. typical values are for information purposes only. u nless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: t j = t c = t a electrical specifications v s + = +5v, v s - = -5v, r f = 750 ? for a v = 1, r f = 375 ? for a v = 2, r l = 150 ? , v enable = v s + - 1v, t a = 25c unless otherwise specified. parameter description conditions min typ max unit ac performance bw -3db bandwidth a v = +1, r l = 500 ?, r f = 510 ? 600 mhz a v = +2, r l = 150 ?, r f = 412 ? 450 mhz bw1 0.1db bandwidth a v = +2, r l = 150 ?, r f = 412 ? 50 mhz sr slew rate v out = -3v to +3v, a v = +2, r l = 100 ? (el5164, el5165) 3500 4700 7000 v/s v out = -3v to +3v, a v = +2, r l = 100 ? (el5364) 3000 4200 6000 v/s t s 0.1% settling time v out = -2.5v to +2.5v, a v = +2, r f = r g = 1k ? 15 ns e n input voltage noise f = 1mhz 2.1 nv/ hz i n - in- input current noise f = 1mhz 13 pa/ hz i n + in+ input current noise f = 1mhz 13 pa/ hz hd2 5mhz, 2.5v p-p -81 dbc hd3 5mhz, 2.5v p-p -74 dbc dg differential gain error (note 1) a v = +2 0.01 % dp differential phase error (note 1) a v = +2 0.01 dc performance v os offset voltage -5 1.5 +5 mv t c v os input offset voltage temperature coefficient measured from t min to t max 6v/c r ol transimpedance 1.1 3 m ? input characteristics cmir common mode input range guaranteed by cmrr test 3 3.3 v cmrr common mode rejection ratio v in = 3v 506275db -icmr - input current common mode rejection -1 0.1 +1 a/v +i in + input current -10 2 +10 a -i in - input current -10 2 +10 a r in input resistance + input 300 650 1200 k ? c in input capacitance 1pf el5164, el5165, el5364
4 output characteristics v o output voltage swing r l = 150 ? to gnd 3.6 3.8 4.0 v r l = 1k ? to gnd 3.9 4.1 4.2 v i out output current r l =10 ? to gnd 100 140 190 ma supply i son supply current - enabled no load, v in = 0v 3.2 3.5 4.2 ma i soff+ supply current - disabled, per amplifier 0 +75 a i soff- supply current - disabled, per amplifier no load, v in = 0v -75 -14 0 a psrr power supply rejection ratio dc, v s = 4.75v to 5.25v 65 79 db -ipsr - input current power supply rejection dc, v s = 4.75v to 5.25v -1 0.1 +1 a/v enable (el5164 only) t en enable time 200 ns t dis disable time 800 ns i ihce ce pin input high current ce = v s +110+25a i ilce ce pin input low current ce = (v s +) -5v -1 0 +1 a v ihce ce input high voltage for power-down v s + - 1 v v ilce ce input low voltage for power-down v s + - 3 v note: 1. standard ntsc test, ac signal amplitude = 286mv p-p , f = 3.58mhz electrical specifications v s + = +5v, v s - = -5v, r f = 750 ? for a v = 1, r f = 375 ? for a v = 2, r l = 150 ? , v enable = v s + - 1v, t a = 25c unless otherwise specified. (continued) parameter description conditions min typ max unit el5164, el5165, el5364
5 typical performance curves figure 1. frequency response for various r f and c l figure 2. frequency response for various r f figure 3. frequency response for various r f figure 4. frequency response for various r f figure 5. frequency response for various power supply voltages figure 6. rise time (ns) 1m 100m 1g frequency (hz) 100k normalized gain (db) 1 0 -1 -2 -3 -4 -5 2 3 4 5 10m r f =1.2k, c l =5pf r f =1.2k, c l =3.5pf r f =1.2k, c l =2.5pf r f =1.2k, c l =0.8pf r f =1.5k, c l =0.8pf r f =2.2k, c l =0.8pf r f =1.8k, c l =0.8pf v cc , v ee = 5v a v = +2 1m 100m 1g frequency (hz) 100k normalized gain (db) 1 0 -1 -2 -3 -4 -5 2 3 4 5 10m r f =160, r g =41 r f =220, r g =55 r f =300, r g =75 r f =360, r g =87 r f =397, r g =97 r f =412, r g =100 r f =560, r g =135 v cc , v ee = 5v c l = 2.5pf a v = +5 1m 100m 1g frequency (hz) 100k normalized gain (db) 2 1 0 -1 -2 -3 -4 3 4 5 6 10m r f = 510 ? r f = 681 ? r f = 750 ? r f = 909 ? r f = 1201 ? v cc , v ee = 5v c l = 2.5pf a v = +1 1m 100m 1g frequency (hz) 100k normalized gain (db) 2 1 0 -1 -2 -3 -4 3 4 5 6 10m v cc = +5v v ee = -5v c l = 5pf a v = +2 r l = 150 ? r f = 562 ? r f = 412 ? r f = 681 ? r f = 866 ? r f = 1.2k ? r f = 1.5k ? 100k frequency (hz) 10m 100m 1g normalized gain (db) 1 0 -1 -2 -3 -4 -5 2 3 4 5 1m 2.5v 3v 4v 5v 6v v cc , v ee= r l = 150 ? r f = 422 ? r g = 422 ? input output amplitude (v) v cc , v ee = 5 v a v = +2 r l = 150 ? ns 2v/div 1v/div el5164, el5165, el5364
6 figure 7. psrr figure 8. distortion vs frequency (a v = +1) figure 9. distortion vs frequency (a v = +2) figure 10. output impedance figure 11. r ol for various v cc , v ee figure 12. voltage noise typical performance curves (continued) 10m 1g frequency (hz) 10k -20 -40 -60 -80 0 100k 1m 100m v ee v cc = +5v v ee = -5v a v = +1 psrr (db) -30 -50 -70 -10 v cc -90 -80 -70 -60 -50 -40 -30 -20 -10 0 0 1020304050 60 frequency (mhz) distortion (db) v cc = +5 v v ee = -5 v a v = +1 v out = 2v p-p r l = 100 ? third harmonic second harmonic thd -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 0102030405060 frequency (mhz) distortion (db) third harmonic second harmonic thd v cc = +5 v v ee = -5 v a v = +2 v out = 2v p-p , r l = 100 ? 10k 100k 1m 100m freqency (hz) 10m output impedance ( ? ) 0.01 0.1 1 10 v cc = +5 v v ee = -5 v a v = +2 10m 1g frequency (hz) 10k 10k 1k 100 10 100k 1m 100k 6v 5v 4v 3v 2.5v v cc , v ee = 1m 100m r ol ( ? ) 100 1k 10k 1m freqency (hz) 100k voltage noise (nv/ hz ) v cc , v ee = 5v 1 0 10 el5164, el5165, el5364
7 figure 13. current noise figure 14. turn on delay figure 15. turn off delay figure 16. differential gain/phase vs dc input voltage at 3.58mhz figure 17. frequency response for various channels figure 18. channel crosstalk between channels typical performance curves (continued) 100 1k 10k 100k frequency (hz) current noise ( pa) v cc = +5v v ee = -5v 10 1 100 v cc = +5v, v ee = -5v a v = +2 r l = 150 ? ch1 ch2 v cc = +5v v ee = -5v a v = +2 r l = 150 ? ch1 ch2 1v 0 -1v dc input differential gain (db) 0 -100 -200 -300 100 200 300 -0.002 -0.003 -0.004 -0.005 -0.001 0.00 0.001 0.002 differential phase () phase magnitude v cc = +5v, v ee = -5v a v = +2 test frequency, 3.58mhz frequency (hz) normalized gain (db) c v cc = +5v v ee = -5v r l = 100 ? r f = 860 ? r g = 860 ? c l = 5pf b a -70 -80 -90 -100 -110 -120 -130 -60 -50 -40 -30 10k 1m 10m 1g 100k 100m 10k frequency (hz) 1m 10m 1g crosstalk (db) -70 -80 -90 -100 -110 -120 -130 -60 -50 -40 -30 100k c to b v cc = +5v v ee = -5v r l = 100 ? r f = 422 ? r g = 422 ? 100m a to c a to b el5164, el5165, el5364
8 figure 19. package power dissipation vs ambient temperature figure 20. package power dissipation vs ambient temperature figure 21. package power dissipation vs ambient temperature figure 22. package power dissipation vs ambient temperature typical performance curves (continued) 909mw 1.4 1.2 1 0.8 0.6 0.2 0 0 25 50 75 100 150 ambient temperature (c) power dissipation (w) 125 85 jedec jesd51-7 high effective thermal conductivity test board 0.4 435mw ja =230c/w sot23-5/6 1.250w ja =80c/w so16 (0.150?) ja =110 c/w so8 1.4 1.2 1 0.8 0.6 0.2 0 0 25 50 75 100 150 ambient temperature (c) power dissipation (w) 125 85 jedec jesd51-7 high effective thermal conductivity test board 0.4 893mw qsop16 ja =112c/w 625mw ja =160c/w so8 1 0.9 0.8 0.6 0.4 0.1 0 0 25 50 75 100 150 ambient temperature (c) power dissipation (w) 125 85 jedec jesd51-3 low effective thermal conductivity test board 0.2 0.7 0.3 0.5 391mw ja =256c/w sot23-5/6 633mw ja =158c/w qsop16 1.2 1 0.8 0.6 0.4 0 0 255075100 150 ambient temperature (c) power dissipation (w) 125 85 jedec jesd51-3 low effective thermal conductivity test board 0.2 1.136w ja =110c/w so16 (0.150?) el5164, el5165, el5364
9 applications information product description the el5164, el5165, and el5364 are current-feedback operational amplifiers that of fers a wide -3db bandwidth of 600mhz and a low supply current of 5ma per amplifier. the el5164, el5165, and el5364 work with supply voltages ranging from a single 5v to 10v and they are also capable of swinging to within 1v of eit her supply on the output. because of their current-feedback topology, the el5164, el5165, and el5364 do not have the normal gain-bandwidth product associated with voltage-feedback operational amplifiers. instead, its -3db bandwidth to remain relatively constant as closed-loop gain is increased. this combination of high bandwidth and low power, together with aggressive pricing make the el5164, el5165, and el5364 ideal choices for many low-power/high-bandwidth applications such as portable, handheld, or bat tery-powered equipment. for varying bandwidth needs, consider the el5166 and el5167 with 1ghz on a 8.5ma supply current or the el5162 and el5163 with 300mhz on a 8.5ma supply current. versions include single, dual, and triple amp packages with 5-pin sot-23, 16-pin qsop, and 8-pin or 16-pin so outlines. power supply bypassing and printed circuit board layout as with any high frequency device, good printed circuit board layout is necessary for optimum performance. low impedance ground plane construction is essential. surface mount components are recommended, but if leaded components are used, lead lengths should be as short as possible. the power supply pins must be well bypassed to reduce the risk of oscillation. the combination of a 4.7f tantalum capacitor in parallel with a 0.01f capacitor has been shown to work well when placed at each supply pin. for good ac performance, parasitic capacitance should be kept to a minimum, especially at the inverting input. (see the capacitance at the inverting input section.) even when ground plane construction is used, it should be removed from the area near the inverting input to minimize any stray capacitance at that node. carb on or metal-film resistors are pin descriptions el5164 (8-pin so) el5164 (6-pin sot-23) el5165 (5-pin sot-23) pin name function equivalent circuit 1, 5 nc not connected 2 4 4 in- inverting input circuit 1 3 3 3 in+ non-inverting input (see circuit 1) 4 2 2 vs- negative supply 6 1 1 out output circuit 2 7 6 5 vs+ positive supply 85 ce chip enable, allowing the pin to float or applying a low logic level will enable the amplifier. circuit 3 in- in+ v s + v s - v s + v s - out v s + v s - ce el5164, el5165, el5364
10 acceptable with the metal-film resistors giving slightly less peaking and bandwidth because of additional series inductance. use of sockets, pa rticularly for the so package, should be avoided if possible. sockets add parasitic inductance and capacitance which will result in additional peaking and overshoot. disable/power-down the el5164 amplifier can be disabled placing its output in a high impedance state. when disabled, the amplifier supply current is reduced to < 150a. the el5164 is disabled when its ce pin is pulled up to within 1v of the positive supply. similarly, the amplifier is enabled by floating or pulling its ce pin to at least 3v below the positive supply. for 5v supply, this means that an el5164 amplifier will be enabled when ce is 2v or less, and disabled when ce is above 4v. although the logic levels are not standard ttl, this choice of logic voltages allows the el5164 to be enabled by tying ce to ground, even in 5v sing le supply applications. the ce pin can be driven from cmos outputs. capacitance at the inverting input any manufacturer?s high-speed voltage- or current-feedback amplifier can be affected by stray capacitance at the inverting input. for inverting gains, this parasitic capacitance has little effect because the inverting input is a virtual ground, but for non-inverting gains, this capacitance (in conjunction with the feedback a nd gain resistors) creates a pole in the feedback path of the amplifier. this pole, if low enough in frequency, has the same destabilizing effect as a zero in the forward open-loop response. the use of large- value feedback and gain resistors exacerbates the problem by further lowering the pole frequency (increasing the possibility of oscillation.) the el5164, el5165, and el5364 have been optimized with a tbd ? feedback resistor. with the high bandwidth of these amplifiers, these resistor values might cause stability problems when combined with parasitic capacitance, thus ground plane is not recommended around the inverting input pin of the amplifier. feedback resistor values the el5164, el5165, and el5364 have been designed and specified at a gain of +2 with r f approximately 412 ? . this value of feedback resistor gives 300mhz of -3db bandwidth at a v = 2 with 2db of peaking. with a v = -2, an r f of 300 ? gives 275mhz of bandwidth with 1db of peaking. since the el5164, el5165, and el5364 are current-feedback amplifiers, it is also possible to change the value of r f to get more bandwidth. as seen in the curve of frequency response for various r f and r g , bandwidth and peaking can be easily modified by varying the value of the feedback resistor. because the el5164, el5165, and el5364 are current- feedback amplifiers, their gain-bandwidth product is not a constant for different closed-loop gains. this feature actually allows the el5164, el5165, and el5364 to maintain about the same -3db bandwidth. as gain is increased, bandwidth decreases slightly while stability increases. since the loop stability is improving with hi gher closed-loop gains, it becomes possible to reduce the value of r f below the specified tbd ? and still retain stability, resulting in only a slight loss of bandwidth with increased closed-loop gain. supply voltage range and single-supply operation the el5164, el5165, and el5364 have been designed to operate with supply voltages having a span of greater than 5v and less than 10v. in practical terms, this means that they will operate on dual supplies ranging from 2.5v to 5v. with single-supply, the el5164, el5165, and el5364 will operate from 5v to 10v. as supply voltages continue to decrease, it becomes necessary to provide input an d output voltage ranges that can get as close as possible to the supply voltages. the el5164, el5165, and el5364 have an input range which extends to within 2v of either supply. so, for example, on 5v supplies, the el5164, el5165, and el5364 have an input range which spans 3v. the output range of the el5164, el5165, and el5364 is also quite large, extending to within 1v of the supply rail. on a 5v supply, the output is therefore capable of swinging fr om -4v to +4v. single-supply output range is larger because of the increased negative swing due to the external pull-down resistor to ground. video performance for good video performance, an amplifier is required to maintain the same output impedance and the same frequency response as dc levels are changed at the output. this is especially difficult when driving a standard video load of 150 ? , because of the change in output current with dc level. previously, good differential gain could only be achieved by running high idle currents through the output transistors (to reduce variat ions in output impedance.) these currents were typically comparable to the entire 5.5ma supply current of each el5164, el5165, and el5364 amplifiers. special circuitry has been incorporated in the el5164, el5165, and el5364 to reduce the variation of output impedance with current output. this results in dg and dp specifications of tbd% and tbd, while driving 150 ? at a gain of 2. video performance has also been measured with a 500 ? load at a gain of +1. under these conditions, the el5164, el5165, and el5364 have dg and dp specifications of 0.01% and 0.01, respectively. output drive capability in spite of their low 5.5ma of supply current, the el5164, el5165, and el5364 are capable of providing a minimum of 75ma of output current. with a minimum of 75ma of output drive, the el5164, el5165, and el5364 are capable of driving 50 ? loads to both rails, making it an excellent el5164, el5165, el5364
11 choice for driving isolation transformers in telecommunications applications. driving cables and capacitive loads when used as a cable driver, double termination is always recommended for reflection-free performance. for those applications, the back-termination series resistor will decouple the el5164, el5165, and el5364 from the cable and allow extensive capacitive drive. however, other applications may have high capacitive loads without a back- termination resistor. in these applications, a small series resistor (usually between 5 ? and 50 ? ) can be placed in series with the output to elim inate most peaking. the gain resistor (r g ) can then be chosen to make up for any gain loss which may be created by this additional resistor at the output. in many cases it is also possible to simply increase the value of the feedback resistor (r f ) to reduce the peaking. current limiting the el5164, el5165, and el5364 have no internal current- limiting circuitry. if the output is shorted, it is possible to exceed the absolute maximum rating for output current or power dissipation, potentially resulting in the destruction of the device. power dissipation with the high output drive cap ability of the el5164, el5165, and el5364, it is possible to exceed the 125c absolute maximum junction temperature under certain very high load current conditions. generally speaking when r l falls below about 25 ? , it is important to calc ulate the maximum junction temperature (t jmax ) for the application to determine if power supply voltages, load conditions, or package type need to be modified for the el5164, el5165, and el5364 to remain in the safe operating area. these parameters are calculated as follows: where: ?t max = maximum ambi ent temperature ? ja = thermal resistance of the package ? n = number of amplifiers in the package ?pd max = maximum power dissipation of each amplifier in the package pd max for each amplifier can be calculated as follows: where: ?v s = supply voltage ?i smax = maximum supply current of 1a ?v outmax = maximum output voltage (required) ?r l = load resistance typical application circuits figure 23. inverting 200ma output current distribution amplifier figure 24. fast-settling precision amplifier t jmax t max ja npd max () + = pd max 2 ( v s i smax ) v s ( v outmax ) v outmax r l ---------------------------- ? + = in+ in- v s + v s - out in+ in- v s + v s - out 0.1f +5v 0.1f -5v 375 ? 5 ? 5 ? 375 ? 375 ? v out v in 0.1f 0.1f +5v -5v in+ in- v s + v s - out in+ in- v s + v s - out 0.1f +5v 0.1f -5v 0.1f 0.1f 375 ? 375 ? 375 ? 375 ? v out v in +5v -5v el5164, el5165, el5364
12 all intersil u.s. products are manufactured, asse mbled and tested utilizing iso9000 quality systems. intersil corporation?s quality certifications ca n be viewed at www.intersil.com/design/quality intersil products are sold by description only. intersil corpor ation reserves the right to make changes in circuit design, soft ware and/or specifications at any time without notice. accordingly, the reader is cautioned to verify that data sheets are current before placing orders. information furnishe d by intersil is believed to be accurate and reliable. however, no responsibility is assumed by intersil or its subsidiaries for its use; nor for any infringements of paten ts or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of intersil or its subsidiari es. for information regarding intersil corporation and its products, see www.intersil.com figure 25. differential line driver/receiver in+ in- v s + v s - out in+ in- v s + v s - out 0.1f +5v 0.1f -5v 375 ? 162 ? 162 ? 375 ? 375 ? v out + v in 0.1f 0.1f +5v -5v v out - in+ in- v s + v s - out in+ in- v s + v s - out 0.1f +5v 0.1f -5v 375 ? 375 ? 375 ? v out 0.1f 0.1f +5v -5v 375 ? 1k ? 1k ? 240 ? 0.1f 0.1f receiver transmitter el5164, el5165, el5364

▲Up To Search▲

Price & Availability of EL5364IUZ-T13

	To Download EL5364IUZ-T13 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .