View FL10801_9041203.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

file loader FL10801 power led driver for automotive applications power saving low side coil driver electronic fuse 390121080101 rev. 00 7 page 1 / 12 2 4/nov /03 author: alx/tfr/buv , rev is ed: ssz 1. scope the following document describes the use of the file loader FL10801. the file loader is intended for use as a programming tool for a single mlx10801 ic as well as an in - circuit - programm er for a completely assembled module. 2. usage the tool has been developed for engineering reasons in order to modify the pretrimmed melexis standard parameter set. it is not intended to be used as a production programming solution. 2.1. programming procedure for a single chip 1) insure that the power supply switch (s1) of th e FL10801 is in off state (refer chapter 3.4.1 for additional information) . 2) plug the FL10801 with a standard lpt cable (connect ed to j2) to a lpt port of a pc . 3) connect the power supply of the FL10801 (j1) . 4) switch on the power su pply . 5) start the FL10801 software on a win95/98/xp pc. the software may also run under winnt/2000, however melexis does not guarantee that. 6) configure the software as described in section 4 . 7) insert a mlx10801 in the emp ty socket of the FL10801 (u200) . 8) select/edit a mlx10801 parameter set out of the FL10801 file loader software package. 9) modify the parameter set to the requirements of the application. 10) program th e modified parameter set . 11) rem ove the mlx10801 ic from the socket of th e FL10801 . 12) check out the programmed ic in the application . 13) repeat steps 7)?12) again to refine the parameter set if necessary . 2.2. programming procedure for a module connected to the FL10801 (e.g. the evb10801) 1) execute step 1)...3) from section 2.1 above . 2) c onnect a module via j3 of the FL10801 according to section 3.4.2 . 3) switch on the power supply . 4) start the FL10801 software on a win95/98/xp pc. the software may also run under winnt/2000, however melexis does not guarantee that. 5) configure the software as described in section 4 . 6) select a mlx10801 parameter set . 7) modify the pretri m med parameter set to the requirements of the application . 8) program the modified paramete r set into the connected module . 9) check out the connected module (led current, light output etc.). 10) repeat steps 7)?9 ) agai n to refine the parameter set .
file loader FL10801 power led driver for automotive applications power saving low side coil driver electronic fuse 390121080101 rev. 00 7 page 2 / 12 2 4/nov /03 author: alx/tfr/buv , rev is ed: ssz 3. h ardware kit 3.1. revision the documentation is valid for the hardware revision FL10801 rev. 2 .0. 3.2. schematics figure 1 : FL10801 schematics
file loader FL10801 power led driver for automotive applications power saving low side coil driver electronic fuse 390121080101 rev. 00 7 page 3 / 12 2 4/nov /03 author: alx/tfr/buv , rev is ed: ssz 3.3. p cb of the FL10801 solder top side solder bottom side figure 2: FL10801 pcb layout pin 1 of the mlx10801 so8 package must be located this way figure 3 : FL10801 pcb c omponent view
file loader FL10801 power led driver for automotive applications power saving low side coil driver electronic fuse 390121080101 rev. 00 7 page 4 / 12 2 4/nov /03 author: alx/tfr/buv , rev is ed: ssz supply connector j1 (+ 10 v..+ 16 v) supply connector j1 ( gnd ) power supply switch pc lpt connector j2 FL10801 status leds mlx10801 ic pins for debugging purpose s and connect ion to a module to be calibrated (j3): pin out : ?1 ?2 ?3 ?4 ?5 ?6 ?7 ?8 ?9 ? 10 (see section 3.4.2 ) socket for mlx10801 to be figure 4 : FL10801 top view programmed figure 5: FL10801 connected to melexis evaluation board evb10801
file loader FL10801 power led driver for automotive applications power saving low side coil driver electronic fuse 390121080101 rev. 00 7 page 5 / 12 2 4/nov /03 author: alx/tfr/buv , rev is ed: ssz 3.4. additional description 3.4.1. FL10801 supply power supply range: + 10? + 16v dc . the FL10801 is reverse polarity protected. the power supply is switched on/off as shown in the following diagram: FL10801 power supply switch j1 supply connector j2 lpt connector pcb FL10801 power supply on FL10801 power supply off figure 6 : location of the FL10801 connectors and the power supply switch no te: the lpt cable between j2 and the pc is a standard 1 : 1 cable ( male/female connector ) . the user has to connect the power supply lines to the mat ch ing connector of j1 which is supplied with the FL10801. this is achieved the following way: insert strip ped ends of the supply leads into the round holes of the connector. on top of the connector there are 2 other holes where the metallic wire holder can be seen. press the wire holder down with a screwdriver or the like and insert the wires into j1. releas e the wire holders to fix the connection.
file loader FL10801 power led driver for automotive applications power saving low side coil driver electronic fuse 390121080101 rev. 00 7 page 6 / 12 2 4/nov /03 author: alx/tfr/buv , rev is ed: ssz 3.4.2. pin out of connector j3: (refer to chapter 3.3 , component view, for the pin order) nr. pin nr pin 1 FL10801 supply 2 ic pin contr 3 FL10801 gnd 4 ic pin drvout 5 ic pin test 6 ic pin rsense 7 ic pin calib 8 ic pin dsense 9 vcc (5v supply) 10 ic pin gnd in case a module is connected to j3, the following connections are nece s sary: j3 pin nr. FL10801 signal connected to the module signal of the module connected to j3 of the f l10801 1 FL10801 supply module pin vbat 1 FL10801 supply module pin control 3 FL10801 gnd module pin gnd 7 ic pin calib calibration point calib 3.4.3. led status indication led meaning led on green mlx10801 ic supply f l10801 power supply on and fileload er software started (standby) yellow read indicator r ead operation in progress (function is not available for the customer) red write indicator w rit e operation in progress
file loader FL10801 power led driver for automotive applications power saving low side coil driver electronic fuse 390121080101 rev. 00 7 page 7 / 12 2 4/nov /03 author: alx/tfr/buv , rev is ed: ssz 4. s oftware kit 4.1. revision th is documentation is valid for the software version s 3 . x . 4.2. content of the setup program installation program: FL10801_ setup.exe (this executable will install all below mentioned files in a specified directory.) main program: mlx10801 .exe help file: readme.txt config file: holds lpt port address and defa ult parameter file example trim files: eva10801_100u_0.47r_100ma.led (sets an application with l=100h and eva10801_100u_0.47r_ 2 00ma.led r shunt =0.47r to a led current of about eva10801_100u_0.47r_350ma.led 100ma, 200ma or 350ma) eva10801_ 22 0u_0.47r _100ma.led (sets an application with l= 22 0h and eva10801_ 22 0u_0.47r_ 2 00ma.led r shunt =0.47r to a led current of about eva10801_220u_0.47r_350ma.led 100ma, 200ma or 350ma) eva10801_ 470 u_ 1 r_100ma.led (sets an application with l= 47 0h and eva10801 _ 47 0u_ 1 r_ 2 00ma.led r shunt = 1 r to a led current of about eva10801_470u_1r_350ma.led 100ma, 200ma or 350ma)
file loader FL10801 power led driver for automotive applications power saving low side coil driver electronic fuse 390121080101 rev. 00 7 page 8 / 12 2 4/nov /03 author: alx/tfr/buv , rev is ed: ssz 4.3. the m ain w indow f igure 7 : FL10801 software main window status of data sent to the mlx10801 p ort address selection load parameter set to the main window save parameter set to file send parameter set to the mlx10801 programmable p arameters ( s ee section 4.3.1 below ) check box es for in - circuit programming of the evb10801
file loader FL10801 power led driver for automotive applications power saving low side coil driver electronic fuse 390121080101 rev. 00 7 page 9 / 12 2 4/nov /03 author: alx/tfr/buv , rev is ed: ssz 4.3.1. progra m mable parameters parameter range / status remarks int ernal /ext ernal temperature sensor internal / external selection of the internal or external temperarture sensor jitter enabled enabled / disabled jitter mode can be enabled or disabled delay generatio n 1ms - 63ms / disabled only used in coil driver mode , defines the start up delay in order to pull relays, microvalves etc. stays otherwise disabled temperature shutoff voltage 300mv - 600mv / disabled temperature switch off point, can be disabled if no tempe rature switch off is desired monoflop time 1s - 63s ( * ) / disabled selection of the drivers off time, coil discharging (passive) state. disabled only in electronic fuse mode peak current threshold voltage 90 - 540mv defines maximum load current , driver sw itches off when threshold voltage is reached (*) if jitter mode is enabled, monoflop time is not selectable with a stepwide of 1 s. as a result of jitter mode , an average monoflop time arises for each time segment. only these average time s (5s, 12s, 20 s, ... etc.) are therefore selectable and thus, displayed in the monoflop time panel. for deta ils about this parameter, see section 14.2 in the datasheet for the mlx10 801 .
file loader FL10801 power led driver for automotive applications power saving low side coil driver electronic fuse 390121080101 rev. 00 7 page 10 / 12 2 4/nov /03 author: alx/tfr/buv , rev is ed: ssz 4.4. t he s oftware u s age before any programming can be executed , the file loader boa rd FL10801 must be powered and switched on as described under 3.4. 4.4.1. programming a single mlx10801 with the FL10801 1) select the lpt port to which the FL10801 is connected. by default this is lpt1. the chosen port will b e displayed in the related panel. 2) p ress the ?load settings? button to select a parameter set file that should be written to the ic. in the example below this is e va10801_220u_0.47r_ 200 ma.led . open the selected file. the name of the selected file is displayed in the ?configuration file? pane l. all individual parameters of this file are shown in the related panels and check boxes. 3) trim the ic with the selected *. led file by pressing the ?trim mlx10801? button . this will upload the displayed parameters to the ic. f igure 8 : opening a mlx10801 parameter set file
file loader FL10801 power led driver for automotive applications power saving low side coil driver electronic fuse 390121080101 rev. 00 7 page 11 / 12 2 4/nov /03 author: alx/tfr/buv , rev is ed: ssz 4.4.2. programming a module connected to the FL10801 this option can be used for in - circuit - programming of the mlx10801 in an assembled module ( e.g. th e melexis evaluation board evb10801). only the module pins v s , gnd and calib need to be available. th ese lines must be connected to the ir respective counterparts on the FL10801 via the j3 connector. connect vs, gnd and calib of the assembled module to j3 of the FL10801. (s ee section 3.4.2 for the pin out of j3) note: make sure that t he mlx10801 socket of the FL10801 is empty if a module is connected t o the FL10801! during programming the module is only driven by the supply of the FL10801. therefore it is necessary to remove/switch off the supply of the module. 1) select the lpt port to which the FL10801 is connected. by default this is lpt1. the chosen port is displayed in the related panel. 2) press the ?load settings? button to select a parameter set file that should be written to the ic. in the example given above this is eva10801_220u_0.47r_200ma.led . open the selected file. the name of the selected file is displayed in the ?configuration file? panel. all individual parameters of this file are shown in the related p anels and check boxes. 3) click the check box ?evb10801 connected? in the upper right corner. after that , the check box ?power supply stays on? becomes active and can be set . if set, the FL10801 supply remains on after the programming cycle. thus, the result of a programming can be easily observed. 4) trim the ic with the selected *.led file by pressing the ?trim mlx10801? button. 5) if necessary, re - trim the ic by making changes to the displayed parameters and upload the changes to the chip by pressing the ?t rim mlx10801? . repeat until the optimal parameters are found.
file loader FL10801 power led driver for automotive applications power saving low side coil driver electronic fuse 390121080101 rev. 00 7 page 12 / 12 2 4/nov /03 author: alx/tfr/buv , rev is ed: ssz for the latest version of this document, go to our website at: www.melexis.com or for additional information contact melexis direct: europe and japan: all other locations: phone: +32 13 61 16 31 phone: +1 603 223 2362 e - mail: sales_europe@melexis.com e - mail: sales_usa@melexis.com qs9000, vda6.1 and iso14001 certified

▲Up To Search▲

Price & Availability of FL10801

	To Download FL10801 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .