View SIT9386_9030526.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

sit 9386 aec - q100, ultra - low jitter differential oscillator preliminary features ? aec - q100 with extended temperature range ( - 40 c to 10 5c) ? any frequency between 1 mhz and 220 mhz , accurate to 6 decimal places . for frequency between 220 and 725 mhz, see sit9387 ? lvpecl, lvds and hcsl output signaling types ? 0.23 ps rms (typ) phase jitter (random, 12 khz to 20 mhz) ? frequency stability as low a s 2 5 ppm C ? industry - standard packages: 3.2 x 2.5, 7.0 x 5.0 mm contact si time for 5.0 x 3.2 mm package applications ? automotive, and other high rel iability electronics ? infotainment syste ms, collision detection devices and in - vehicle 10/40/100 gbps ethernet electrical characteristics all min and max limits in the electrical c haracteristics tables are specified over temperature and rated operating voltage with standard output termination show in the termination diagrams. typical values are at 25c and nominal supply voltage. table 1 . electrical character istics D common to lvpecl, lvds and hcsl parameter symbol min. typ. max. unit condition frequency range output frequency range f 1 C 220 mhz accurate to 6 decimal places frequency stability frequency stability - 25 C +25 ppm inclusive of initial tolera nce, operating temperature, rated power supply voltage and load variations. contact sitime for 25 ppm. - 50 C +50 ppm inclusive of initial tolerance, operating temperature, rated power supply v oltage and load variations. first year aging f_1y C 1 C ppm at 25c temperature range operating temperature range t_use - 40 C +85 c industrial - 40 C +105 c extended industrial supply voltage supply voltage vdd 2.97 3.3 3.63 v 2.7 3.0 3.3 v 2.52 2.8 3.08 v 2.25 2.5 2.75 v input characteristics input voltage high vih 70% C C vdd pin 1, oe input voltage low vil C C 30% vdd pin 1, oe input pull - up impedance z_in C 100 - k pin 1, oe logic high or logic low output characteristics d uty cycle dc 45 C 55 % startup and oe timing start - up time t_start C C 3.0 ms measured from the time vdd reaches its rated minimum value. oe enable/disable time t_oe C C 3.8 s f = 156.25 mhz. rev 0.90 november 24, 2017 www.sitime.com
sit9 3 8 6 aec - q100, ultra - low jitter differential oscillator preliminary rev 0.90 page 2 of 12 www.s itime.com table 2 . electrical characteristics C lvpecl parameter symbol min. typ. max. unit condition current consumption current consumption idd C C 89 ma excluding load termination current, vdd = 3.3v or 2.5v oe disable supply current i_oe C C 58 ma oe = low output disable leakage current i_leak C 0.15 C ? a oe = low maximum output current i_driver C C 32 ma maximum average current drawn from out+ or out - output c haracteristics output high voltage voh vdd - 1.1 C vdd - 0.7 v see figure 2 output low voltage vol vdd - 1.9 C vdd - 1.5 v see figure 2 output differential voltage swing v_swing 1.2 1.6 2.0 v see figure 3 rise/fall time tr, tf C 225 ps 20% to 80%, see figure 2 jitter rms phase jitter (random) t_phj C 0.220 ps f = 156.25 mhz, integration bandw i dth = 12 khz to 20 mhz, all vdd levels, includes spurs, 7.0 x 5.0 mm package. C 0.225 ps f = 156.25 mhz, integration bandwidth = 12 khz to 20 mhz, all vdd levels, i ncludes spurs, 3.2 x 2.5 mm package. C 0.1 C ps f = 156.25, ieee802.3 - 2005 10gbe jit ter mask integration b andwidth = 1.875 mhz to 20 mhz , includes spurs, all vdd levels. rms period jitter [ 1 ] t_jitt C 1.0 ps f = 100, 156.25 or 212.5 mhz, vdd = 3.3v or 2.5v notes: 1. measured accordin g to jesd65b table 3 . electrical characteristics C lvds parameter symbol min. typ. max. unit condition current consumption current consumption idd C C 79 ma excluding load termination current, vdd = 3.3v or 2.5v oe disable suppl y current i_oe C C 58 ma oe = low output disable leakage current i_leak C 0.15 C ? a oe = low output characteristics differential output voltage vod 250 C 455 mv see figure 4 vod magnitude change vod C C 50 mv see figure 4 offset voltage vos 1.125 C 1.375 v see figure 4 vos magnitude change vos C C 50 mv see figure 4 rise/fall time tr, tf C 400 ps measured with 2 pf capacitive loading to gnd, 20% to 80%, see figure 4 jitter rms phase jitter (random) t_phj C 0.215 ps f = 156.25 mhz, integration bandwi dth = 12 khz to 20 mhz, all vdd levels, includes spurs, 7.0 x 5.0 mm package. 0.235 ps f = 156.25 mhz, integration ban dwidth = 12 khz to 20 mhz, all vdd levels, i ncludes spurs, 3.2 x 2.5 mm package. C 0.1 C ps f = 156.25, ieee802.3 - 2005 10gbe jitter mask integration b andwidth = 1.875 mhz to 20 mhz , includes spurs, all vdd levels. rms period jitter [ 2 ] t_jitt C 1.0 ps f = 100, 156.25 or 212.5 mhz, vdd = 3.3v or 2.5v notes: 2. measured according to jesd65b
sit9 3 8 6 aec - q100, ultra - low jitter differential oscillator preliminary rev 0.90 page 3 of 12 www.s itime.com table 4 . electrical characteristics C hcsl parameter symbol min. typ. max. unit con dition current consumption current consumption idd C C 89 ma excluding load termination current, vdd = 3.3v or 2.5v oe disable supply current i_oe C C 58 ma oe = low output disable leakage current i_leak C 0.15 C ? a oe = low maximum output current i_driver C C 35 ma maximum average current drawn from out+ or out - output characteristics output high voltage voh 0.60 C 0.90 v see figure 2 output low voltage vol - 0.05 C 0.0 8 v see figure 2 output differential voltage swing v_swing 1.2 1.4 1.80 v see figure 3 rise/fall time tr, tf C 360 ps measured with 2 pf capacitive loading to gnd, 20% t o 80%, see figure 2 jitter rms phase jitter (random) t_phj C 0.220 ps f = 156.25 mhz, integration bandwi dth = 12 khz to 20 mhz, all vdd levels, includes spurs, 7.0 x 5.0 mm package. C 0.230 ps f = 156.25 mh z, integration bandwidth = 12 khz to 20 mhz, all vdd levels, i ncludes spurs, 3.2 x 2.5 mm package. C 0.1 C ps f = 156.25, ieee802.3 - 2005 10gbe jitter mask integration b andwidth = 1.875 mhz to 20 mhz , includes spurs, all vdd levels. rms period jitter [ 3 ] t_jitt C 1.0 ps f = 100, 156.25 or 212.5 mhz, vdd = 3.3v or 2.5v notes: 3. measured according to jesd65b table 5 . pin description pin map functionality 1 oe/nc output enable (oe) h [ 4 ] : specified frequency output l: output is high impedance non connect (nc) h or l or open: no effect on output frequenc y or other device functions 2 nc na no connect; leave it floating or connect to gnd for better heat dissipation 3 gnd power vdd power supply ground 4 out+ output oscillator output 5 out - output complementary oscillator output 6 vdd power power supply voltage [ 5 ] notes: 4. in oe mode, a pull - u p resistor of 10 k or less is recommended if pin 1 is not externally driven. 5. a capacitor of value 0.1 f or higher between vdd and gnd is required. an additional 10 f capacitor between vdd and gnd is required for the best phase jitter performance top vie w figure 1 . pin assignments 4 3 1 6 g n d v d d o u t + 5 2 n c o u t - o e / n c
sit9 3 8 6 aec - q100, ultra - low jitter differential oscillator preliminary rev 0.90 page 4 of 12 www.sitime.com table 6 . absolute maximum ratings attempted operation outside the absolute maximum ratings may cause permanent damage to the part. actual pe rformance of the ic is only guaranteed within the operational specifications, not at absolute maximum ratings. parameter min. max . unit vdd - 0.5 4 .0 v vih vdd + 0.3v v vil - 0.3 v storage temperature - 65 150 o c maximum junction temperature 130 o c soldering temperature (follow standard pb - free soldering guidelines) 260 o c table 7 . thermal consideration s [ 6 ] package ? ja , 4 layer board (c/w) ? jc , bottom (c/w) 3225, 6 - pin 80 30 7050, 6 - pin 52 19 notes: 6. refer to jesd51 for ? ja and ? jc definitions, and referenc e layout used to determine the ? ja and ? jc values in the above ta ble. table 8 . maximum operating junction temperature [ 7 ] max operating temperature (a mbient) maximum operating junction temperature 70c 95 c 85c 110 c 10 5c - notes: 7. datasheet specifications are not guaranteed if junction temperature exceeds the maximum operating junction temperature. table 9 . environmental co mpliance parameter test conditions value unit mechanical shock resistance mil - std - 883f, method 2002 10, 000 g mechanical vibration resistance mil - std - 883f, method 2007 70 g soldering temperature (follow standard pb free soldering guidelines) mil - std - 883 f, method 2003 260 c moisture sensitivity level msl1 @ 260 c electrostatic discharge (hbm) hbm, jesd22 - a114 2 , 000 v charge - device model esd protection jesd220c101 750 v latch - up tolerance jesd78 compliant
sit9 3 8 6 aec - q100, ultra - low jitter differential oscillator preliminary rev 0.90 page 5 of 12 www.sitime.com waveform diagrams figure 2 . lvpecl/hcsl voltage levels per differential pin (out+/out - ) figure 3 . lvpecl/hcsl voltage levels across differential pair figure 4 . lvds voltage levels per differential pin (out+/out - ) o u t + o u t - g n d t r t f 2 0 % 8 0 % 2 0 % v o l 8 0 % v o h 0 v t v _ s w i n g o u t + o u t - g n d t r t f 2 0 % 8 0 % 2 0 % v o s 8 0 % v o d
sit9 3 8 6 aec - q100, ultra - low jitter differential oscillator preliminary rev 0.90 page 6 of 12 www.sitime.com termination diagrams lvpecl: figure 5 . lvpecl with ac - coupled termination figure 6 . lvpecl dc - coupled load termination with thevenin equivalent network figure 7 . lvpecl with y - bias termination o u t + o u t - 5 0 ? z o = 5 0 ? z o = 5 0 ? v t 5 0 ? s h u n t b i a s t e r m i n a t i o n n e t w o r k d - d + 0 . 1 f 0 . 1 f l v p e c l r b r b v d d r b 1 0 0 ? 4 8 . 7 ? 3 . 3 v 2 . 5 v vdd r 1 r 2 r 1 r 2 out+ out - out+ out - vdd r 1 82.5 ? 127 ? 62.5 ? 250 ? 3.3 v 2.5 v r 2 zo = 50? zo = 50? thevenin - equivalent termination network d - d+ d - d+ lvpecl r 1 r 2 out+ out - out+ out - vdd r 1 50 ? 50 ? 50 ? 50 ? 3.3 v 2.5 v r 2 r 3 50 ? 18 ? zo = 50? zo = 50? r 3 c 1 0.1 f y - bias termination network d - d+ d - d+ lvpecl
sit9 3 8 6 aec - q100, ultra - low jitter differential oscillator preliminary rev 0.90 page 7 of 12 www.sitime.com termination diagrams ( c ontinued) figure 8 . lvpecl with dc - coupled parallel shunt load termination out+ out - out+ out - 50 ? zo = 50? zo = 50? v t =vdd - 2v 50 ? shunt bias termination network d - d+ d - d+ lvpecl
sit9 3 8 6 aec - q100, ultra - low jitter differential oscillator preliminary rev 0.90 page 8 of 12 www.sitime.com termination diagrams ( c ontinued) lvds: figure 9 . lvds single dc termination at the load figure 10 . lvds double ac termination with capacitor close to the load figure 11 . lvds double dc termination out+ out - out+ out - 100 ? zo = 50? zo = 50? lvds out+ out - out+ out - o u t + o u t - 1 0 0 ? z o = 5 0 ? z o = 5 0 ? 0 . 1 f 0 . 1 f l v d s o u t + o u t - 1 0 0 ? o u t + o u t - 1 0 0 ? z o = 5 0 ? z o = 5 0 ? l v d s o u t + o u t - 1 0 0 ?
sit9 3 8 6 aec - q100, ultra - low jitter differential oscillator preliminary rev 0.90 page 9 of 12 www.sitime.com termination diagrams ( c ontinued) hcsl: figure 12 . hcsl interface termination out+ out - out+ out - zo = 50? zo = 50? d - d+ d - d+ r2 r1 r1 = r2 = 33 ? 50? 50?
sit9 3 8 6 aec - q100, ultra - low jitter differential oscillator preliminary rev 0.90 page 10 of 12 www.sitime.com dimensio ns and patterns package size C dimensions (unit: mm) [ 8 ] recommended land pattern (unit: mm) [ 9 ] 3.2 x 2.5 x 0.85 mm 3.2 x 2.5 x 0.85 mm 7.0 x 5.0 x 0.85 mm [ 10 ] 7.0 x 5.0 x 0.85 mm [ 10 ] notes : 8. top marking: y denotes manufacturing origin and xxxx denotes manufacturing lot number. the value of y will depend on the assembly location of the device . 9. a capacitor of value 0.1 f or higher between vdd and gnd is required. an add itional 10 f capacitor between vdd and gnd is required for the best phase jitter performance 10. the center pad has no electrical function. soldering down the center pad to the gnd is recommended for best thermal dissipat ion, but is optional. 1 . 0 5 0 . 6 5 1 . 0 0 2 . 2 5 1 . 6
sit9 3 8 6 aec - q100, ultra - low jitter differential oscillator preliminary rev 0.90 page 11 of 12 www.sitime.com ordering inf ormation notes: 11. contact sitime for higher temperature range options . 12. contact sitime for 5.0 x 3.2 mm package . 13. contact sitime for 2 5 ppm option . 14. bulk is available for sampling only . table 10 . ordering codes for supported tape & reel packing method device size (mm x mm) 8 mm t&r (3ku) 8 mm t&r (1ku) 12 mm t&r (3ku) 12 mm t&r (1ku) 16 mm t&r (3ku) 16 mm t&r (1ku) 7.0 x 5.0 t y 3.2 x 2.5 d e t y s i t 9 3 8 6 a c - 1 b 2 - 3 3 e 1 2 3 . 4 5 6 7 8 9 t f r e q u e n c y 1 . 0 0 0 0 0 0 t o 2 2 0 . 0 0 0 0 0 0 m h z p a r t f a m i l y s i t 9 3 8 6 r e v i s i o n l e t t e r a i s t h e r e v i s i o n o f s i l i c o n t e m p e r a t u r e r a n g e [ 1 1 ] p a c k a g e s i z e [ 1 2 ] f r e q u e n c y s t a b i l i t y 2 : 2 5 p p m [ 1 3 ] 3 : 5 0 p p m i : i n d u s t r i a l , - 4 0 t o 8 5 c e : e x t e n d e d i n d u s t r i a l , - 4 0 t o 1 0 5 c s i g n a l l i n g t y p e 1 : l v p e c l 2 : l v d s 4 : h c s l v o l t a g e s u p p l y 2 5 : 2 . 5 v 1 0 % 2 8 : 2 . 8 v 1 0 % 3 0 : 3 . 0 v 1 0 % 3 3 : 3 . 3 v 1 0 % f e a t u r e p i n b : 3 . 2 x 2 . 5 m m e : 7 . 0 x 5 . 0 m m w i t h c e n t e r p a d p a c k a g i n g t , y , d o r e r e f e r t o t a b l e b e l o w f o r p a c k i n g m e t h o d l e a v e b l a n k f o r b u l k [ 1 4 ] n : n o c o n n e c t e : o u t p u t e n a b l e
sit9 3 8 6 aec - q100, ultra - low jitter differential oscillator preliminary rev 0.90 page 12 of 12 www.sitime.com t able 11 . additional information d ocument description download link eccn #: ear99 five character designation used on the commerce control list (ccl) to ide ntify dual use items for export control purposes. part number generator tool used to create the part number based on desired features. time machine ii mems oscillator programmer http://www.sitime.com/support/time - machine - oscillator - programmer field programmab le oscillators devices that can be programmable in the field by time machine ii http://www.sitime.com/products/field - programmable - oscillators manufacturing notes tape & reel dimension, reflow profile and other manufacturing related info ht tp:// www.sitime.com/component/docman/doc_download/243 - manufacturing - notes - for - sitime - oscillators qualification reports rohs report, reliability reports, composition reports http://www.sitime.com/support/quality - and - reliability performance reports additional performance data such as phase noise, current consumption and jitter for selected frequencies ht tp:// www.sitime.com/support/performance - measurement - report termination techniques termination design recommendations http://www.sitime.com/support/application - notes layout techniques layout recommendations http://www.sitime.com/support/application - notes table 12 . revision history revision release date change summary 0.1 0 3/11/2017 initial draft 0.87 11/06 /2017 updated package drawing s c orrected tape/reel ordering information updated electrical characteristics based on charac terization i ncluded max numbers for ipj a dded additional information table c orrected formatting issues i ncreased temperature range from 95oc to 105oc r emoved 10 ppm options for automotive and industrial temperature ranges changed 20 ppm to contact sitim e u pdated termination diagrams lower mechanical shock from 20,000 to 10,000 g 0.90 11/ 24 /2017 ordering information updates and page layout changes sitime corporation , 5451 patrick henry drive , santa clara , ca 95054 , usa | phone: + 1 - 408 - 328 - 4400 | fax: +1 - 408 - 328 - 4439 ? sitime corporation 2016 - 2017. the information contained herein is subject to change at any time without notice. sitime assumes no responsibility or liability for any loss, damage or defect of a product which is caused in whole or in part by (i) use of any circuitry other than circuitry embodied in a sitime produc t, (ii) misuse or abuse including static discharge, neglect or accident, (iii) unauthorized modification or repairs which have been soldered or alte red during assembly and are not capable of being tested by sitime under its normal test conditions, or (iv) improper installation, storage, handling, warehousing or transportation, or (v) being subjected to unusual physical, thermal, or electrical stress. disclaimer: sitime makes no warranty of any kind, express or implied, with regard to this material, and specifically disclaims any and al l express or implied warranties, either in fact or by operation of law, statutory or otherwise, including the implied warranties of merchantability and fitness for use or a particular purpose, and any implied warranty arising from course of dealing or usage of trade, as well as any common - law duties relating to accuracy or lack of negligence, with respect to this material, any sitime product and any product documentation. products sold by sitime are not suitable or intended to be used in a life support application or component, to operate nuclear facilities, or in other mission critical applications where human life may be involved or at stake. all sales are made conditioned upon compliance with the critical uses policy set forth below. critical use exclusion policy buyer agrees not to use sitime's products for any application or in any components used in life support devices or to operate nuclear facilities or for use in other mission - critical applications or components where human life or property m ay be at stake. sitime owns all rights, title and interest to the intellectual property related to sitime's products, including any software, firmware, copyright, patent, or trademark. the sale of sitime products does not convey or imply any license under patent or other rights. sitime retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale of products or services by sitime. unless otherwise agreed to in writing by sitime, any reproduction, modification, translation, compilation, or representation of this material shall be strictly prohibited.

▲Up To Search▲

Price & Availability of SIT9386

	To Download SIT9386 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .