View FXP1500_9028821.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

the FXP1500/1800 front - ends are power - factor - corrected (pfc) and provide a 48 vdc (1500 or 1800 watt) output, and can be used in hot - swap redundant systems. their very small dimensions allow configuration of up to three units in a 1u rack. the fxp front - ends have a rear - mounted ac connector. the highly efficient thermal design with int ernal - fan cooling permits their use over wide temperature ranges and provides very high reliability. status information is provided with front panel leds, logic signals, and via an i 2 c management interface. in addition, the i 2 c bus can enable the power supply, set high fan speed, adjust the output voltage, and set the output current limit. the FXP1500/1800's meet international safety standards and display the ce - mark for the european low voltage fxr - 3 - 48g power - shelf solutions provide rectification, syst em management, and power distribution, while maintaining high reliability and offering flexibility for future expansion. the power shelves can be configured with up to three hot - swappable 1500 or 1800 - watt ac - dc front - ends. ? rohs compliant for all six substances ? high density front - ends 15.2 to 18.3 w/in 3 ? wide input voltage range 85 to 264 vac ? 12 v standby voltage, 1 a per front - end ? highly efficient topology reduces operating costs ? i 2 c interface status and control ? i 2 c voltage and c urrent limit setting ? analog output voltage setting ? overtemperature, output overvoltage, and output overcurrent protection ? oring circuits for true redundant operation: v o1 : oring fets; v o2 : oring diodes ? status leds: ac ok, dc ok, and fan fail/overtemperature fail ? telecommunications ? data c ommunications ? servers ? distributed p ower
2 FXP1500/1800 ; fxr - 3 - 48g tech.support@psbel.com model input voltage vac auto selected 1 output 1 output 2 rated power w compatible shelf 2 v o1 nom vdc i o1 max adc v o2 nom vdc i o2 max adc FXP1500 - 48g 105 C 264 85 C 105 48 48 32.2 25.4 12 12 1 1 1512 1212 fxr - 3 - 48g fxp1800 - 48g 180 C 264 105 C 180 85 C 105 48 48 48 39.2 32.2 25.4 12 12 12 1 1 1 1812 1512 1212 fxr - 3 - 48g 1 the available output power is automatically adjusted depending on the input voltage. 2 1u standard racks are available from bel power solutions. see the rack (power shelf) section of this data sheet for configura tions and d etails. stress in excess of the absolute maximum ratings may cause performance degradation, adversely affect long - term reliability, or cause permanent damage to the converter. parameter conditions / description min max unit input voltage continuous transient, 60 ms max. 264 300 vac operating ambient temperature v i min - v i max , i o nom , cooling by internal fan @ 100 % load @ 50 % load 0 0 50 70 c storage temperature non - operating - 40 85 c specification is valid for input voltage, load, and temperature ranges, unless otherwise stated. parameter conditions / description min nom max unit input voltage 85 230 264 vac input frequency 47 50/60 63 hz turn - on input voltage ramping up 79 85 vac turn - off input voltage ramping down 70 78 vac inrush current limitation 115/230 vac acc. ets 300 132 - 1 < 100 ms 50 a pk hold - up time after last ac line peak , v i = 230 vac, p o nom 20 ms power factor v i nom , i o nom 0.95 w/va efficiency v i = 230 vac, i o nom , t c = 25 c 89 90 % max input current 20 a rms input connector 16 a C 20 a / 250 vac; according to iec320 c19
FXP1500/1800 ; fxr - 3 - 48g 3 asia - pacific +86 755 298 85888 europe, middle east +353 61 225 977 north america +1 408 785 5200 ? 2016 bel power solutions & protection bcd.00023 _a d specification is valid for input voltage, load, and temperature ranges, unless otherwise stated. parameter conditions / description min nom max units nominal output voltage vo1 i o = 16.1 a 48 vdc nominal output voltage vo2 i o = 0.5 a 12 vdc output voltage set point accuracy v i = 230 vac, i o1 =16 .1 a, t c = 25 c (47.8 - 48.2 vdc) - 0.5 +0.5 % v o1 nom output voltage trimming (via i 2 c or with external resistor) adjustable (44.16 to 51.84 vdc) - 8 +8 % v o1 nom nominal current output 1 FXP1500 - 48g i o1 nom @ v i =105 vac C 264 vac, p o 1.5 kw i o1 nom @ v i = 85 vac C 105 vac, p o 1.2 kw 32.2 25.4 adc adc fxp1800 - 48g i o1 nom @ v i =180 vac C 264 vac, p o 1.8 kw i o1 nom @ v i =105 vac C 180 vac, p o 1.5 kw i o1 nom @ v i = 85 vac C 105 vac, p o 1.2 kw 39.2 32.2 25.4 39.2 adc adc adc current limit output 1 FXP1500 - 48g i o1 max @ v i = 105 vac C 264 vac droop hiccup i o1 max @ v i = 85 vac C 105 vac droop hiccup 36.8 30 adc adc fxp1800 - 48g i o1 max @ v i = 180 vac C 264 vac droop hiccup i o1 max @ v i = 105 vac C 180 vac droop hiccup i o1 max @ v i = 85 vac C 105 vac droop hiccup 43.8 36.8 30 adc adc adc nominal current output 2 i o2 nom @ vi = 85 vac C 264 vac, p o 12 w 1.0 1.0 adc current limit output 2 i o2 max @ v i = 85 vac C 264 vac 1.5 adc static line regulation output 1 v i min - v i max , 50 % i o nom - 0.5 0.5 % v o nom static load regulation output 1 (droop characteristic) FXP1500 - 48g v i = 230 v, 5 - 100 % i o nom v o : full load (32.2 adc) to no load 46.65 83.5 48 49.34 mv/a vdc fxp1800 - 48g v i = 230 v, 5 - 100 % i o nom v o : full load (32.2 adc) to no load 46.07 83.5 48 49.34 mv/a vdc static load regulation output 2 (droop characteristic) v i = 230 v, 5 - 100 % i o nom v o : full load (32.2 adc) to no load 0.4 vdc dynamic load regulation load change 50 % < - > 100 % i o nom , di o /dt =1 a/ ? s voltage deviation (droop + ove r - or undershoot) FXP1500 - 48g - 5 5 % v o nom fxp1800 - 48g - 5.7 5.7 % v o nom all models max. recovery time to within 1 % of v o1 nom 400 ? s current share difference in current between two units for v o1 above 10 % load. FXP1500 - 48g 3.2 adc fxp1800 - 48g 3.9 adc start - up time time required for output within regulation after initial application of ac - input ( v i nom , i o nom ) after removal of inhibit ( v i nom , i o nom ) 100 1.5 s ms output voltage ripple a nd noise ( filter 10 nf /10 f ) v i nom , i o nom , 20 mhz bandwidth v o1 v o2 480 120 mv pp mv pp remote sense total compensation for cable losses 500 mv parameter conditions/description min nom max unit input fuse not user accessible 25 a, fast blow inrush current limitation with ntcs output no - load - , short circuit - and overload proof overvoltage protection latching 3 tracking absolute 115 122 59.5 % v o nom v overtemperature protection automatic power shutdown at t c 95 c 3 remove input voltage to reset.
4 FXP1500/1800 ; fxr - 3 - 48g tech.support@psbel.com specification is valid for input voltage, load, and temperature ranges, unless otherwise stated. parameter type 4 conditions / description visual status indication fp led indicators 5 : ? dc ok (green) ? ac ok (green) ? fan fail & over - temperature (amber) i 2 c communication bus oc[s1, s2] ? monitors alarm functions and allows control of specific parameters. ? uses standard philips two wire bus (scl and sda signal lines) i 2 c communication bus addressing oc[t1 - t5] five lines provide up to 32 separate psu i 2 c addresses ps present pin oc[u3] ? used by system to indicate a psu is installed in a system shelf ? contact closure to logic ground ( internal pull - down resistor of 1 k ? ) ps main ou tput remote shutdown oc[r1] ? ttl compatible signal, inhibited when open contact, high or at ttl logic 1 ? signal referenced to logic return (lrtn) fp two position switch in series with oc signal (logical and) allows local enable/disable; 0 position => ps disabled; 1 position => ps enabled power supply ok i 2 c ac ok & dc ok & no overcurrent & no over - temperature & fans working dc current fail i 2 c reports over - current condition on main output, i o1 ac fail / power down warning oc[u2] & i 2 c provides a warning that the input power has failed at least 5 ms before the output falls out of regulation (<90% v o1 set). ? open collector signal with 20 ma pull - down capability, referenced to logic return (lrtn). ? ac fail will go high or open during power fail condition and will go low when input is within the operating range. ? a power fail warning will turn off the front panel green ac ok led. dc fail / output voltage fault oc[u4] & i 2 c internal under - voltage a nd overvoltage supervision of v o1 . ? open collector signal with 20 ma pull - down capability, referenced to logic return (lrtn). ? dc fail will go high or open if v o1 < 90% or v o1 > 110% of v o1 set, measured in front of the oring fets. ? green led on the front panel indicates normal operation; led will flash if in parallel operation v o1 is ok, but the unit is disabled. critical temperature warning/fan fail oc[u1] & i 2 c indicates the psu operating temperature has reached [t shut - down C 10k] indicates if the unit is in over - temperature shutdown. ? open collector signal with 20 ma pull - down capability, referenced to logic return (lrtn). ? the oc - output will go low 100 ms before an over - temperature condition shuts down the unit. ? an ambe r led on the front panel indicates over - temperature or fan fail. dc voltage monitoring i 2 c monitors the main output voltage, v o1 , seen at the output connector. accuracy is 0.45v over setting range and temperature. dc current monitoring i 2 c monitors the output current i o1 : accuracy 0.4a over the load range. dc voltage trimming (margining) oc[r4] output voltage trimming v o1 : 8% of v o set using external resistor i 2 c setting accuracy over i2c: 50mv at v o1 nom, 150mv over setting range fan speed control i 2 c two fan speed levels automatically set depending on the internal temperature. the fan speed can be set to full speed or automatic control via i 2 c command. fan ok/fail oc[u1] & i 2 c indicates if the cooling fans are operating or have failed. synchronized startup pin oc[r5] overcurrent signal which can be used for synchronous startup of units in parallel or to recover from an overload condition. 4 abbreviations used: ? oc[#] => hardwired signal accessible at psu output connector, with pin number reference ? fp => provided by devices located on psu front panel ? i 2 c => signal provided over i 2 c communication system; detailed i 2 c information is available from the specific models i 2 c manual found on the bel power solutions web site. 5 see led function table for further details
FXP1500/1800 ; fxr - 3 - 48g 5 asia - pacific +86 755 298 85888 europe, middle east +353 61 225 977 north america +1 408 785 5200 ? 2016 bel power solutions & protection bcd.00023 _a d parameter conditions / description min nom max unit altitude operating non - operating 10 k 40 k asl ft. relative humidity, non - condensing operating 10 90 % rh storage 5 95 % rh temperature coefficient 0 c to 70 c (after 15 min warm - up) 0.02 %/k shock iec/en 60068 - 2 - 27, 11 ms 40 g pk sinusoidal vibration iec/en 60068 - 2 - 6 2 - 8 hz 8 - 200 hz 200 - 500 hz 7.5 2 4 mil g pk g pk random vibration 10 - 2000 hz 6.15 g rms mtbf calculated per bellcore (sr - 332, issue 1): gb 25 c gb 25 c (fnp1500 - 12g) demonstrated 230 tbd 250 kh maximum electric strength testing is performed in the factory according to en50514 , iec/en60950 - 1 2 nd ed. and ul/csa60950 - 1 2 nd ed. input - to - output electric strength tests should not be repeated in the field. bel power solutions will not honor any warranty claims resulting from electric strength field tests. parameter conditions / description min nom max unit agency approvals approved to latest edition of the following standards: ul/csa60950 - 1, iec60950 - 1 and en60950 - 1. ce mark for lvd insulation safety rating input to case input to output output to case basic reinforced functional electric strength test voltage input to case input to output output to case output 1 to output 2 2.12 4.2 6 0.5 0.1 kvdc kvdc kvdc kvdc 6 subassemblies are pre - tested with 4.2 kvdc in accordance with en50514 and iec/en60950 - 1 2 nd ed. parameter description criterion electrostatic discharge iec/en 61000 - 4 - 2, level 4 performance criterion b electromagnetic field iec/en 61000 - 4 - 3, level 3 performance criterion a electrical fast transients/burst iec/en 61000 - 4 - 4, level 3 performance criterion b surge iec/en 61000 - 4 - 5, level 3 performance criterion b voltage dips a nd interruptions iec/en 61000 - 4 - 11 performance criterion b or better rf conducted immunity iec/en 61000 - 4 - 6 10 vac, am 80 %, 1 khz performance criterion a emissions conducted cispr 22/en 55022/en 61204 class b emissions radiated cispr 22/en 55022/en 61204 class a harmonics iec/en 61000 - 3 - 2 class b voltage fluctuation a nd flicker iec/en 61000 - 3 - 3 pass voltage sag semi f47 - 0200 (high line 230 v) pass
6 FXP1500/1800 ; fxr - 3 - 48g tech.support@psbel.com output connector description oc pin # type signal reference low level high level v max i max over - temperature / fan fail u1 oc - output, protected by 16 v zener diode and a 10 ? resistor in series lgnd <0.4 v @ 20 ma pull up 15 v 20 ma ac fail / power down warning u2 <0.4 v @ 20 ma pull up 15 v 20 ma power supply present u3 1k ? resistor connected to logic gnd lgnd open pull up 10 v 10 ma dc fail / output voltage fault u4 oc - output, protected by 16 v zener diode and a 10 ? resistor in series lgnd <0.4v @ 20 ma pull up 15 v 20 ma internal ground (int gnd) u5 used only for addrx and v o1 set. do not connect the internal grounds in systems with several units. connected to v o1 - line before the output filter - - addr0 i 2 c address bus t1 high = internal 10 k ? pu to 5v=> logic 1 low = connect to int gnd => logic 0 int gnd logic 1 logic 0 5v 0v addr1 i 2 c address bus t2 addr2 i 2 c address bus t3 addr3 i 2 c address bus t4 addr4 i 2 c address bus t5 sda, i 2 c serial data line s1 i 2 c compatible signal referenced to logic gnd 5 v or 3.3 v logic lgnd logic 1 logic 0 3.3v to 5v 0v scl, i 2 c serial clock line s2 auxiliary power +12 v s3 v o2 + output, isolated from main output aux output is floating - - auxiliary power +12vrtn s4 aux output return; ground isolated from main output logic ground (lgnd) s5 internally connected to aux gnd through 10 ? resistor. wire lgnd separately from aux rtn and main output gnd to minimize noise on signals and i 2 c bus. leave open if not used. - - - output inhibit r1 r1 ps active when pulled low (dc - dc stage off when left open) lgnd < 0.8 v >2.0 v 10 v 3.5 ma v sense + r2 open or connected tov o1 + at the load internally connected to v o1 + via 100 ? . - - dv<3 vpp 30 ma v sense - r3 open or connected tov o1 - at the load internally connected to v o1 - via 100 ? . - - output margin r4 oper or connected to int gnd (+8% v o1 ) or v sense+ ( - 8% v o1 ), do not interconnect margin pins in systems with paralleled psus. - - 60 v synchronized startup (for paralleled units) r5 open or connected to synch startup circuit vo1 C at the oc 12 v 2 ma v o1 - p1, p3, p5 main output - pins - - - v o1 + p2, p4, p6 main output + pins - - - input connector description oc pin # type protection earth p1 pe phase p2 l neutral p3 n
FXP1500/1800 ; fxr - 3 - 48g 7 asia - pacific +86 755 298 85888 europe, middle east +353 61 225 977 north america +1 408 785 5200 ? 2016 bel power solutions & protection bcd.00023 _a d condition power fail (ac ok) output good (dc ok) fan fail and over - temperature normal operation green green off power supply i s inhibited green off amber input ac i s low off off amber input ac is low or missing off off amber/off over - temperature green off amber output overload (in regulation) green green off output overloaded (out of regulation) green off off fan fault (no overtemperature shutdown) green green amber fan fault (with overtemperature shutdown) green off amber power supply failed off off off/ amber mechanical dimensions (w x h x d) : 5.6 (141.2 mm) x 1.6 (40.5 mm) x 12 (304.8 mm)
8 FXP1500/1800 ; fxr - 3 - 48g tech.support@psbel.com female ledge connector: manufacturer: fci output connector part no.: 51762 - 106020000aa lf (horizontal) output connector part no.: 51742 - 106020000aa lf (vertical) input connector part no.: 51915 - 056lf (horizontal) input connector part no.: 51940 - 099lf (vertical) information on availability under http://www.stkcheck.com/evs/fcielectronics/fcisearch.asp for parallel use in minimal configuration systems, only the inhibit pins must be shorted to logic gnd. all other pins can be left open. the power supplies will share the output current automatically (droop current share). for parallel applications without i2c bus, but the use of all other features, it is recommended to connect all logic gnds on a backplane together, to connect all vo2 - , all v o2 + and to leave the internal gnds open. the sense wires can be left open or connected to a common load point, the synch - start pin can be left open or connected to a synch - start circuit, the inhibit pins can be connected together or used individually. all i2c signals (t1 - t5, s1, and s2) can be left open. use of a small foil capacitor > 3f directly at the power outputs of each unit is recommended in order to prevent voltage drops at the hot plug. for additional information on paralleling see the following rack (power shelf) section. to achieve best cooling results sufficient airflow through the unit must be ensured. do not block or obstruct the airflow at the rear of the unit by placing large components directly at the output connector.
FXP1500/1800 ; fxr - 3 - 48g 9 asia - pacific +86 755 298 85888 europe, middle east +353 61 225 977 north america +1 408 785 5200 ? 2016 bel power solutions & protection bcd.00023 _a d each rack (power shelf) is 1u high with backplane and designed for up to three front - end models in parallel or in n+1 operation. each power shelf has: ? massive copper bus bars for low - loss current distribution. ? output terminals with two m4 - screws on each power tab. ? two fast - on contacts for system earthing. ? address coding over five pole dip switch on each unit, 37 - pin d - sub connector with i 2 c - lines, monitoring signals and support functions. ? provides a start - up synchronization circuit and emv filters. overall mechanical dimensions (w x h x d): 17.7 (449.6 mm) x 1.7 (43.1 mm) x 14 (355.6 mm) fxr - 3 - 48 g power shelf front view location description a earth connection b 5 - bit dip switch for i 2 c addressing of psu #3 c mains connector of psu #3 d output 1 minus e output 1 plus f 5 - bit dip switch for i 2 c addressing of psu #2 g mains connector of psu #2 h 37 - pin sub - d connector, control, sense, check and auxiliary power (output 2) i 5 - bit dip switch for i 2 c addressing of psu #1 j mains connector of psu #1 l3 n3 pe3 l2 n2 pe2 l1 n1 pe1 a b c d e f g h i j
10 FXP1500/1800 ; fxr - 3 - 48g tech.support@psbel.com output connector description oc pin type signal reference low level high level v max i max overtemperature / fan fail psu1 1 oc - output, protected by 16 v zener diode and a 10 resistor in series. lgnd <0.4 v @ 20 ma pull up 15 v 20 ma power supply present psu 1 2 resistor (1 k ? ) connected to logic gnd lgnd open pull up 10 v 10 ma power supply present psu 2 3 spare 4 overtemperature / fan fail psu 3 5 oc - output, protected by 16 v zener diode and a 10 resistor in series. lgnd <0.4 v @ 20 ma pull up 15 v 20 ma ac fail /power down warning psu 3 6 power supply present psu 3 7 resistor (1 k ? ) connected to logic gnd lgnd open pull up 10 v 10 ma dc fail / output voltage fault psu 3 8 oc - output, protected by 16 v zener diode and a 10 resistor in series lgnd <0.4 v @ 20 ma pull up 15 v 20 ma overtemperature / fan fail psu 2 9 synch._start_a 10 sync_start_a , active high the signals of several racks can be connected together in such a way that all supplies will be inhibited until the last supply has recovered from its overcurrent condition. lgnd <7v off < 9v 15v 10ma spare 11 output inhibit psu 1 - 3 12 dc - dc stage on when pin is open or connected to lgnd dc - dc stage off when pin is connected on high potential lgnd <0.8 v >2.0 v 10 v 3.5 ma v sense + 13 open or connected to v o1 + at the load internally (psu) connected to v o1 + over 100 v o1+ dv < 3 v pp 30 ma v sense - 14 open or connected to v o1 - at the load internally (psu) connected to v o1 - over 100 v o1 - dv < 3 v pp 30 ma spare 15 nc 16 nc 17 nc 18 nc 19 ac fail/power - down warning psu 1 20 oc - output, protected by 16 v zener diode and a 10 resistor in series lgnd <0.4 v @ 20 ma pull up 15 v 20 ma dc fail/output voltage fault psu 1 21 ac fail/power - down warning psu 2 22 dc fail/output voltage fault psu 2 23 sda, i 2 c data line 24 i 2 c compatible signal lgnd 5 v or 3.3 vlogic scl, i 2 c clock line 25 i 2 c compatible signal lgnd 5 v or 3.3 v logic vo2+ = +12 v (auxiliary power) 26 vo2+ aux output, insulated from main output aux output is isolated supply vo2 - = +12 vrtn (auxiliary power) 27 vo2 - aux output, insulated from main output logic gnd (lgnd) 28 wire separately from auxiliary and main output gnd to minimize noise and avoid voltage drops on signal - and i2c return. leave open if not used. internally connected to vo2 auxiliary gnd via 10 ? output margin psu 1 29 open or connected to v sense: v sense - (+8 % vo1) or v sense+ ( - 8 % vo1) 60 v output margin psu 2 30 output margin psu 3 31 nc 32 nc 33 nc 34 nc 35 nc 36 nc 37
FXP1500/1800 ; fxr - 3 - 48g 11 asia - pacific +86 755 298 85888 europe, middle east +353 61 225 977 north america +1 408 785 5200 ? 2016 bel power solutions & protection bcd.00023 _a d sub - d output connector the FXP1500 - 48g and fxp1800 - 48g power supplies exhibit an overcurrent hiccup behaviour. this means if either of these supplies reaches an overcurrent limit, the output voltage will immediately turn off and after a delay turn on again. in paral lel use, all power supplies have to start synchronized because of the internal hiccup behaviour. otherwise, the supply which has reached overcurrent first will go to hiccup; this will overload the other supplies, which then will also go to hiccup. when the firs t supply has recovered from hiccup (hiccup dead time), the others remain in hiccup. this will immediately drive the fi rst one into hiccup once again. this means that without a start - up circuit, a system with several power supplies can never recover from an overload condition or start - up into full load. the following additional circuit, required to reach synchronized star tup, is already implemented inside the fxr - 3 - 48g shelf. the following connection between the shelves is required to achieve a parallel operation. the synch - start circuits inside the shelves inhibit all power supplies until the last one has recovered from its overcurrent condition and then synchronize the restart of the outputs.
12 FXP1500/1800 ; fxr - 3 - 48g tech.support@psbel.com description pin location, definition type signal reference low level high level v max i max auxiliary p ower +12 v (output 2) 26 v o2 +, aux output, insulated from main output logic g round 28 logic_gnd ,internally connected over 10 ? to v o2 - , ( auxiliary power ground (output 2)) internally connected o2 - output i nhibit_a psu 1 - 3 12 inhibit_a, dc - dc stage on when pin is open or connected to lgnd dc - dc stage off when pin is connected on high potential lgnd <0.8 v >2.0 v 10 v 3.5 ma synch. startup 1 psu 1 - 3 r5 (at psu) the synch_start pin is connected to the over - current signal of the psu1 - 3. in the case of an overcurrent shutdown, this signal goes high. v o1 - <7v off > 9v 15v 10ma synch. startup_a rack fxr - 3 - 48g 1 - n pin on the d - sub connector on the backplane 10 sync_start_a, active high the signals of several racks can be connected together in such a way that all supplies will be inhibited until the last supply has recovered from its overcurrent condition. lgnd note: the sync - start pins can be wired together only if the power supplies are connected with a minimal voltage drop on power ground as achieved on a backplane with massive copper bus bars. if there is a less ideal connection, it is recommended to use an o pto - coupler for each unit (ic1, d3, d2).
FXP1500/1800 ; fxr - 3 - 48g 13 asia - pacific +86 755 298 85888 europe, middle east +353 61 225 977 north america +1 408 785 5200 ? 2016 bel power solutions & protection bcd.00023 _a d center angular brackets are set in the middle for shelf mounting: center angular bracket sets can be ordered: bel power solution s part no.: hzz01222 note: each center angular bracket set contains 2 brackets and 8 screws. filler for covering of the empty shelf slots
14 FXP1500/1800 ; fxr - 3 - 48g tech.support@psbel.com filler can be ordered: bel power solutions part no.: xak.00043.0 plastic cover set for the bus bars: plastic cover set can be ordered: bel power solution s part no.: xeb.00031.0 note1: available upon special request. note2: each plastic cover set contains 2pcs. the handle has been designed to allow easy plug - in and - out in a rack system. the handle (lever) fits into a counter piece (fulcrum) which is fixed to the bottom of the rack. during the plug, the fulcrum holds the unit down and guides it towards the output connector. the bel power solutions part number of the fulcrum and its associated mounting accessories is: hzz01223. individual fulcrum sets can be also ordered: bel power solution s part no.: hzz01223. note: each hzz01223 set contain 2 fulcrums, 2 supp orts, and mounting accessories.
FXP1500/1800 ; fxr - 3 - 48g 15 asia - pacific +86 755 298 85888 europe, middle east +353 61 225 977 north america +1 408 785 5200 ? 2016 bel power solutions & protection bcd.00023 _a d i 2 c management software : all fnp and fxp front - ends can be controlled via bel power solution s gui - driven i 2 c management software and an i 2 c - to - usb interface (p/n hzz02002g). an i 2 c programming manual describes the complete range of parameters that can be programmed to the FXP1500/1800 front - ends. this manual is available by searching on "FXP1500" at www.belpowersolutions.com. nuclear and medical applications - products are not designed or intended for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems. technical revisions - the appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. specifications are subject to change without notice. i 2 c usb interface

▲Up To Search▲

Price & Availability of FXP1500

	To Download FXP1500 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .