www.micropowerdirect.com micropower direct 292 page street suite d stoughton, ma 02072 usa t: (781) 344-8226 f: (781) 344-8481 e: sales@micropowerdirect.com w: www.micropowerdirect.com key features: ? 2w output power ? 8.0 kv isolation ? 15 kv/ s cmti ? reinforced insulation ? en 60950 approved (pend.) ? compact smt case ? -25c to +80c operation ? tape & reel available mhi200lri8 compact, 2w smt ultra-high isolation dc/dc con vert ers input parameter conditions min. typ. max. units input voltage range 5 vdc input 4.5 5.0 5.5 vdc 12 vdc input 10.8 12.0 13.2 24 vdc input 21.6 24.0 26.4 input filter capacitor filter output parameter conditions min. typ. max. units output voltage accuracy ?.0 ?.0 % output voltage balance dual output, balanced loads ?.1 ?.0 % line regulation v in = min to max ?.2 ?.5 % load regulation, see note 2 see model selection guide ripple & noise (20 mhz) see note 3 150 mv p - p temperature coef cient ?.01 ?.02 %/? output short circuit momentary (0.5s max) general parameter conditions min. typ. max. units isolation voltage rated for 60 sec 4,000 vac rms tested for 1 sec 8,000 vdc isolation resistance 500 vdc 10 g? isolation capacitance 100 khz, 1v 15 20 pf common mode transient immunity 15 kv/? switching frequency 50 80 100 khz environmental parameter conditions min. typ. max. units operating temperature range ambient -25 +25 +80 ? case +90 storage temperature range -50 +125 ? cooling free air convection humidity rh, non-condensing 95 % physical case size see mechanical diagram (page 2) case material non-conductive black plastic (ul94-v0) weight 0.125 oz (3.75g) reliability speci? cations parameter conditions min. typ. max. units mtbf mil hdbk 217f, 25?, gnd benign 2.0 mhours moisture sensitivity level (msl) ipc/jedec j-std-020d level 2 safety standards ul 60950, en 60950 (pending) absolute maximum ratings parameter conditions min. typ. max. units input voltage surge (0.1 sec) 5 vdc input 9.0 vdc 12 vdc input 18.0 24 vdc input 30.0 lead free re ow solder process ipc/jedec j-std-020d.1 caution: exceeding absolute maximum ratings may damage the module. these are not continuous operating ratings. electrical speci? cations speci cations typical @ +25?, nominal input voltage & rated output current, unless otherwise noted. speci cations subject to change without notice. series
www.micropowerdirect.com micropower direct we power your success - for less! 292 page street ste d stoughton, ma 02072 tel: (781) 344-8226 fax: (781) 344-8481 e-mail: sales@micropowerdirect.com mechanical dimensions pin single output 1-v in 7 no connection 8 no connection 9+v out 10 -v out 16 +v in pin con nec tions notes: all dimensions are typical in inches (mm) tolerance x.xx = ?.02 (?.50) pin dual output 1-v in 7 no connection 8 common 9+v out 10 -v out 16 +v in model selection guide model number input output ef? ciency (%, typ) load regulation (%, max) capacitive load (f, max) fuse rating slow-blow (ma) voltage (vdc) current (ma) voltage (vdc) current (ma, max) current (ma, min) nominal range full-load no-load mhi205s-05lri8 5 4.5 - 5.5 615 90 5.0 400 8.0 65 ?2.0 330 1,200 mhi205s-12lri8 5 4.5 - 5.5 609 90 12.0 165 3.0 65 ?0.0 330 1,200 mhi205s-15lri8 5 4.5 - 5.5 605 90 15.0 133 2.5 66 ?0.0 330 1,200 mhi205d-12lri8 5 4.5 - 5.5 553 90 ?2.0 ?3 ?.5 72 ?0.0 100 1,200 mhi205d-15lri8 5 4.5 - 5.5 542 90 ?5.0 ?6 ?.0 73 ?0.0 100 1,200 mhi212s-05lri8 12 10.8 - 13.2 256 40 5.0 400 8.0 65 ?2.0 330 600 mhi212s-12lri8 12 10.8 - 13.2 254 40 12.0 165 3.0 65 ?0.0 330 600 mhi212s-15lri8 12 10.8 - 13.2 252 40 15.0 133 2.5 66 ?0.0 330 600 mhi212d-12lri8 12 10.8 - 13.2 224 40 ?2.0 ?3 ?.5 74 ?0.0 100 600 MHI212D-15LRI8 12 10.8 - 13.2 220 40 ?5.0 ?6 ?.0 75 ?0.0 100 600 mhi224s-05lri8 24 21.6 - 26.4 128 30 5.0 400 8.0 65 ?2.0 330 250 mhi224s-12lri8 24 21.6 - 26.4 127 30 12.0 165 3.0 65 ?0.0 330 250 mhi224s-15lri8 24 21.6 - 26.4 126 30 15.0 133 2.5 66 ?0.0 330 250 mhi224d-12lri8 24 21.6 - 26.4 112 30 ?2.0 ?3 ?.5 74 ?0.0 100 250 mhi224d-15lri8 24 21.6 - 26.4 110 30 ?5.0 ?6 ?.0 75 ?0.0 100 250 notes: 1. the speci ed maximum capacitive load is for each output. 2. load regulation is measured over a range of 20% i out to 100% i out . 3. when measuring output ripple & noise, it is recommended that an external capacitor (3.3 f typ.) be placed from the +v out to the -v out pins for single output units and from each output to common for dual output models. 4. the converter should be connected to a low ac-impedance source. an input source with a highly inductive impedance may affect the stability of the converter. in applications where the converter output loading is high and input power is supplied over long lines, it may be necessary to use a capacitor on the input to insure start-up. in this case, it is recom- mended that a low esr (esr <1.0 at 100 khz) capacitor be mounted close to the converter. for 5v input units a 2.2 f is recommended; for 12v input units, a 1.0 f; and for 24v units a 0.47 f. 5. operation at no-load will not damage the unit, but they may not meet all speci cations. 6. it is recommended that a fuse be used on the input of a power supply for protection. see the model selection tables for the correct rating. board layout derating curve igbt applications notes: the mhi200x-xxl series is a good choice for applications involving high speed switching, such as driving igbts. they are designed to withstand the extra stress caused by the high voltage switching transients present in igbt drive circuits. all of the mhixxx series have isolation levels that range from 5.2 to 8 kv. many of these have reinforced insulation. the high isolation levels (and the correspond- ingly low capacitive coupling rates) allow them to be safely used in applications with highly dynamic switched ac or dc.
|
