View EVAL-ADG5209FEBZ_8951149.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

eval - adg5209febz user guide ug - 875 one technology way ? p. o . box 9106 ? norwood, ma 02062 - 9106, u.s.a. ? tel: 781.329.4700 ? fax: 781.461.3113 ? www.analog.com evaluating the adg5209f , overvoltage protected dual 4:1 multiplexer please see the last page for an important warning and legal terms and conditions . rev. a | page 1 of 12 features supply voltages dual supply: 5 v to 22 v single supply: 8 v to 44 v protected against overvoltage on source pins signal voltages up to ?55 v and +55 v parallel interface compatible with 3 v logic on - board low dropout ( ldo ) regulator for digital supply and control, if required evaluation kit conte nts eval - adg5209f ebz evaluation board online resources documents needed adg5209f data sheet eval - adg5209f ebz user guide equipment needed dc voltage source 22 v for dual supply 44 v for single supply optional digital logic supply : 3 v to 5 v analog signal source me thod to measure voltage, such as a digital multimeter (dmm) general description the e va l - adg5209f ebz is the evaluation board for the adg5209f a nd features an overvoltage protected d ual 4:1 m ultiplexer . the adg5209f has overvoltage detection and protection circuitry on the source pins and is protected against signals up to ?55 v and +55 v in both the powered and unpowered state s. figure 1 shows the e va l - adg5209f ebz in a typical evaluation setup. the adg5209f is s oldered to the center of the evaluation board, and wire screw terminals are provided to connect to each of the source and drain pins. three screw terminals power the device, with a fourth terminal used to provide a user defined digital logic supply voltage , if required. alternatively, a low dropout (ldo) regulator is provided for 5 v digital logic supply . full specifications on the adg5209f are available in the adg5209f data sheet, which must be consulted in conjunction with this user guide when using the evaluation board. typical evaluation s etup 13457-001 power supp l y signa l gener a t or figure 1. eval - adg5209f ebz , power supply, and signal generator
ug- 875 eval - adg5209febz user guide rev. a | page 2 of 12 table of contents features .............................................................................................. 1 evaluation kit contents ................................................................... 1 online resources .............................................................................. 1 equipment needed ........................................................................... 1 general desc ription ......................................................................... 1 typical evaluation setup ................................................................. 1 revision history ............................................................................... 2 getting started .................................................................................. 3 evaluation boa rd setup procedure ............................................ 3 evaluation board hardware .............................................................4 power supply ..................................................................................4 input signals ...................................................................................4 jumper settings ..................................................................................5 switches and 0 ? resistors ...........................................................5 smb connectors ............................................................................5 evaluation board schematics and artwork ...................................6 ordering information .................................................................... 11 bill of materials ........................................................................... 11 revision history 5/2016 rev. 0 to rev. a changes to figure 1 .......................................................................... 1 changes to input signals section ................................................... 4 changes to smb connectors section and table 1 ....................... 5 8 / 20 15 revision 0: initial version
eval - adg5209febz user guide ug- 875 rev. a | page 3 of 12 getting started evaluation board set up procedure the e va l - adg5209f ebz e valuatio n board operate s independently and does not require any additional evaluation boards or software to operate. an on - board ldo regulator is provided as the digital power supply to manually control the adg5209f . supply the evaluation board with a dual power source of up to 22 v or a single supply of up to + 44 v by connecting vss and gnd together. a functionality test can be set up as follows: 1. connect a power supply to j 5 . connect vss and gnd together if a single supply is required. 2. ensure a 0 ? resistor is inserted in r1 5 to use the on - board ldo regulator , and that a 0 ? resistor is inserted in r 14. 3. sw1 through sw 3 control the digital signals for the adg5209f . s 1 a v dd d a ad g 52 0 9 f ad p 71 4 2 (l d o ) s 4 a j1 : s 1 a j3 : d a j1 : s 4 a v d d e x t _ v l j 5 j 5 vs s j 5 g n d v ss g n d f au l t detection and switch driver r13 = ex t _ v l r 14 = l d o s w 1 s w 2 s w 3 e n a 0 a 1 j2 : s 1 b j2 : s 4 b s 1 b s 4 b j4 : d b d b 13457-002 figure 2. eval - adg5209f ebz block diagram
ug- 875 eval - adg5209febz user guide rev. a | page 4 of 12 evaluation board har dware the operation of the adg5209f is evaluated using the e va l - adg5209f ebz . figure 1 shows a typical evaluation setup where only a power supply and signal generator are required. figure 2 shows the block diagram of the main components of the evaluatio n board. using this evaluation board, the adg5209f pass es signals from either the source or drain connectors. the source pins have fault detection circuitry that react to an overvoltage event. during an overvoltage event, the channel on which the fault occurs is turned off . see the adg5209f data sheet for more details. power supply connector j 5 provides access to the supply pins of the adg5209f . vdd, gnd, and vss on j5 link to the appropriate pins on the adg5209f . for dual - supply voltages, the evaluation board can be powered from 5 v to 22 v. for single - supply voltages , the gnd and vss terminals must be connected together, and power the evaluation board with 8 v to 44 v. additionally, an on - board ldo regulator is provided for a digital control voltage. if necessary , a secondary volta ge source can be connected to ext _v l and used to control the digital voltages. to use ext_vl , move the 0 ? resistor from r 14 to r13 . do not expose the on - board ldo regulator to voltages greater than 28 v; remove r 15 and supply an alternative digital voltage via ext_vl , if required. input signals four screw connectors are provided to connect to both the source a nd drain pins of the adg5209f . additional s ubminiature version b (smb) connector pads are available if extra connections are required. the adg5209f is overvoltage prote cted on the source side, an d each source terminal (s1 a to s4a and s1b to s4b ) can be presented with a voltage of up to +55 v or ?55 v. see the adg5209f data sheet for more details. each trace on the source and drain side includes two sets of 0603 pads that can be used to place a load on the signal path to ground. a 0 ? resistor is placed in the signal path and can be replaced with a user defined value. use t he resistor combined with the 0603 pads to create a simple resistor capacitor (rc) filter. the adg5209f uses a parallel interface to control the operation of the switches. the switch operation can be manually controlled using the sw1 to sw3 switches , or an external controll er can be interfaced directly to the control pins by using the smb connectors ( en, a0 , and a1 ) and removing the 0 ? r31, r33, and r35 resistors .
eval - adg5209febz user guide ug- 875 rev. a | page 5 of 12 jumper settings switches and 0 ? resi s tors s witches control the adg5209f manually and 0 ? resistors configu re the digital control voltage . table 2 shows a summary of the switches and 0 ? resistors and how they are used on the evaluation board. use sw2 and sw3 to control the switches of the adg5209f . position l (low) is tied to gnd and sets the logic low , and position h (high) is tied to vl and sets the logic high . use sw1 to enable or disable the device. position dis (disable) is tied to gnd and disables the device, and position en (enable) is tied to vl and enables the device. table 1 . adg5209f truth table sw3 (a1) sw2 (a0) sw1 (en) connected sx x 1 x 1 dis (disable) all switches off l (low) l (low) en (enable) s1a/s1b l (low) h (high) en (enable) s2a/s2b h (high) l (low) en (enable) s3a/s3b h (high) h (high) en (enable) s4a/s4b 1 x means dont care. r1 5 connects the on - board ldo regulator to the vdd supply. remove this resistor to protect the ldo regulator from voltages higher than 28 v. change the 0 ? resistor to the r 13 position to use an alternative digital voltage connected to dc_v1. smb connectors the parallel interface of the adg5209f is controlled manually using the link headers ( sw 1 to sw3 ) , or it can be accessed using the smb connectors (en , a0, and a1 ) . to us e the smb connectors, remove the 0 ? r31, r33 , and r35 resistors . table 2 . switch and 0 ? resistor descriptions label position description sw1 dis (disable) logic 0 on the en pin en (enable) logic 1 on the en pin sw2 l (low) logic 0 on the a0 pin h (high) logic 1 on the a0 pin sw3 l (low) logic 0 on the a1 pin h (high) logic 1 on the a1 pin r13/r14 r14 on - board ldo regulator digital voltage r13 ext_vl digital voltage r15 inserted ldo regulator powered up removed ldo regulator unpowered r31, r33, r35 inserted sw1 to sw 3 are used to control digital logic removed smb connectors are used to control digital logic
ug- 875 eval - adg5209febz user guide rev. a | page 6 of 12 evaluation board sch ematics and artwork 13457-008 figure 3. adg5209f evaluation board schematic ( part 1)
eval - adg5209febz user guide ug- 875 rev. a | page 7 of 12 13457-008 figure 4. adg5209f evaluation board schematic ( part 2) 13457-010 figure 5. adg5209f evaluation board schematic ( part 3)
ug- 875 eval - adg5209febz user guide rev. a | page 8 of 12 13457-007 figure 6. eval - adg5209f ebz silkscreen 13457-003 figure 7. eval - adg5209f ebz top layer
eval - adg5209febz user guide ug- 875 rev. a | page 9 of 12 13457-004 figure 8. eval - adg5209f ebz layer 2 13457-005 figure 9. eval - adg5209f ebz layer 3
ug- 875 eval - adg5209febz user guide rev. a | page 10 of 12 13457-006 figure 10 . eval - adg5209f ebz bottom layer
eval - adg5209febz user guide ug- 875 rev. a | page 11 of 12 ordering information bill of materials table 3 . reference designator description manufacturer part number stock code a0, a1, en 50 , straight , smb jack s smb1251b1 - 3gt30g-50 fec 1111349 c3, c4, c7, c8 50 v , x7r , 0603 size, 0.1 f, multilayer ceramic capacitor s grm188r71h104ka93d fec 882 - 0023 c1, c2 50 v , tantalum, d size , 10 f capacitor s tajd106k050rnj fec 143 - 2387 c5, c6 ceramic , multilayer , 4.7 f capacitor s c2012x5r1h475k125ab fec 2346932 da, db 50 , smb socket s smb1251b1 - 3gt30g-50 do not insert gnd1, gnd2 black test point s 20- 2137 fec 873 - 1128 j1, j2, j5 4 -p in terminal block s (5 mm pitch ) ctb5000/4 fec 151791 j3, j4 2 -p in terminal block s (5 mm pitch ) ctb5000/2 fec 151789 r2, r5, r8, r11, r12, r17, r20, r23, r26, r29, r31, r33, r35, r38, r41 0603 , 1% , 0 resistor s mc0063w06030r fec 9331662 r1, r3, r4, r6, r7, r9, r10, r16, r18, r19, r21, r22, r24, r25, r27, r28, r30, r37, r39, r40, r42 smd , 0603 resistor s not applicable do not insert r32, r34, r36 1 k , 0.063 w, 1%, 0603 , resistor s mc0063w060311k fec 9330380 r14, r15 0805 , 1% , 0 resistor s mc01w08050r fec 9333681 r13 smd , 0805 resistor not applicable do not insert s1a, s2a, s3a, s4a, s1b, s2b, s3b, s4b, 50 , smb socket s smb1251b1 - 3gt30g-50 do not insert sw1, sw2, sw3 single - pole, double throw ( spdt ) , smt slide switch es cas - 120ta digi - k ey cas120jct - nd t1, t2, t3, t4, t5, t6, t7, t8, t9, t10 red test point s 20- 313137 fec 873 - 1144 t_a0, t_a1, t_en red test point s 20- 313137 fec 873 - 1144 u1 fault protection, ? 0.4 pc q inj , dual 4:1 multiplexer adg5209fbruz adg5209fbruz u2 linear regulator , 5.0 v, ldo adp7142aujz - 5.0 adp7142aujz - 5.0-r7
ug- 875 eval - adg5209febz user guide rev. a | page 12 of 12 notes esd caution esd (electrostatic discharge) sensitive device . charged devices and circuit boards can discharge without detection. although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy esd. therefore, proper esd precautions should be taken t o avoid performance degradation or loss of functionality. legal terms and conditions by using the evaluation board discussed herein (together with any tools, components documentation or support materials, the evaluation board), you are agreeing to be bound by the terms and conditions set forth below (agreement) unless you have purchase d the evaluation board, in which case the analog devices standard terms and conditions of sale shall govern. do not use the e valuation board until you have read and agreed to the agreement. your use of the evaluation board shall signify your acceptance of the agreement. this agreement is made by and between you (customer) and analog devices, inc. (adi), with its principal place of business at one technology way, norwood, ma 02062, usa. subject to the terms and conditi ons of the agreement, adi hereby gr ants to customer a free, limited, personal, temporary, non - exclusive, non - sublicensable, non - transferable license to use the evaluation board for evaluation purposes only. customer understands and agrees that the evalu ation board is provided for the sole a nd exclusive purpose referenced above, and agrees not to use the evaluation board for any other purpose. furthermore, the lic ense granted is expressly made subject to the following additional limitations: customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the evaluation board; and (ii) permit any third party to access the evaluation bo ard. as used herein, the term third party includes any entity other than adi, customer, their employees, affiliates and in - house consultants. the evaluation board is not sold to customer; all rights not expressly granted herein, including ownership of the evaluation board, are reserved by adi. confidentiality. this agreement and the evaluation board shall all be considered the confi dential and proprietary information of adi. customer may not disclose or transfer any portion of the evaluation board to any other party for any reason. upon discontinuation of use o f the evaluation board or termination of this agreement, customer agrees t o promptly return the evaluation board to adi. additional restrictions. customer may not disassemble, decompile or reverse engi neer chips on the evaluation board. customer shall inform adi of any occurred damages or any modifications or alterations it make s to the evaluation board, including but not limited to soldering or any other activity that affects the material content of the evaluation board. modifications to the evaluation board must comply with applicable law, including but not limited to the rohs directive. termination. adi may terminate this agreement at any time upon giving written notice to customer. customer agrees to return to adi the evaluation board at that time. limitation of liability. the evaluation boar d provided hereunder is provided a s is and adi makes no warranties or representations of any kind with respect to it. adi specifically disclaims any representations, endorsements, g uarantees, or warranties, express or implied, related to the evaluation board including, but not limited to, the implied warranty of merchantability, title, fitness for a particular purpose or noninfringement of intellectual property rights. in no event will adi and its licensors be liable for any incidental, special, indirect, or consequential dam ages resulting from customers possession or use of the evaluation board, including but not limited to lost profits, delay costs, labor costs or loss of goodwill. adis total li ability from any and all causes shall be limited to the amount of one hundred us dollars ($10 0.00). export. customer agrees that it will not directly or indirectly export the evaluation board to another country, and th at it will comply with all applicable united states federal laws and regulations relating to exports. governing law. this agreemen t shall be governed by and construed in accordance with the substantive laws of the commonwealth of massachusetts (excluding conflict of law rules). any legal action regarding this agreement will be heard in the state or fede ral courts having jurisdiction in suffolk county, massachusetts, and customer hereby submits to the personal jurisdiction and venue of such courts. the united nations convention on contracts for the internation al sale of goods shall not apply to this agreement and is expressly disclaime d. ? 2015 C 2016 analog devices, inc. all rights reserved. trademarks and registered trademarks are the property of their respective owners. ug13457 - 0 - 5/16(a)

▲Up To Search▲

Price & Availability of EVAL-ADG5209FEBZ

	To Download EVAL-ADG5209FEBZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .