View LTL1NHSJ4D_8941715.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lite-on dcc release lite-on technology corp. / optoelectronics no.90,chien 1 road, chung ho, new taipei city 23585, taiwan, r.o.c. tel: 886-2-2222-6181 fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto through hole lamp product data sheetLTL1NHSJ4D spec no.: ds20-2013-0032effective date: 03/19/2013revision: - bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y features * high luminous intensity output. * low power consumption. * high efficiency. * versatile mounting on p.c. board or panel. * i.c. compatible/low current requirement. * 3.1 mm diameter package. package dimensions part no. lens source col or ltl1 n h s j4 d amber diffused alingap yellow notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25mm(.010") unless otherwise noted. 3. protruded resin under flange is 0.5 mm(.0 2 ") max and depressed resin under flange is 0.5 mm(.0 2 ") max . 4. lead spacing is measured where the leads emerge from the package. 5. specifications are subject to change without notice. part no. : ltl1 n h s j4 d page : 1 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y absolute maximum ratings at t a = 25 parameter maximum rating unit power dissipation 75 mw peak forward current (1/10 duty cycle, 0.1ms pulse width) 60 ma dc forward current 2 0 ma reverse voltage 5 v operating temperature range - 40 c to + 85 c storage temperature ran ge - 40 c to + 100 c lead soldering temperature [1.6mm(.063") from body] 260 c for 5 seconds part no. : ltl1 n h s j4 d page : 2 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y electrical / optical characteristics at t a =25 parameter symbol min. typ . max. unit test condition luminous intensity i v 2 40 70 0 115 0 mcd i f = 20ma note 1 viewing angle 2 1/2 2 5 deg note 2 (fig.5) peak emission wavelength p 591 nm measurement @peak (fig.1) dominant wavelength d 58 6 5 90 59 4 nm note 4 spectral line half - width ? 15 nm forward voltage v f 1.6 2. 1 2. 6 v i f = 20ma reverse current i r 100 a r = 5v note 5 note: 1. luminous intensity is measured with a light sensor and filter combination that approximates the cie eye - response curve. 2. 1/2 is the off - axis angle at which the luminous intensity is half the axial luminous intensity. 3. iv classification code is marked on each packing bag. 4. the dominant wavelength, d is derived from r ) condition is applied for ir test only. the device is not designed for reverse operation. part no. : ltl1 n h s j4 d page : 3 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y typical electrical / optical characteristics curves (25 ambient temperature unless otherwise noted) part no. : ltl1 n h s j4 d page : 4 of 10 bns - od - c131/a 4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y packing spec 1000 , 500 , 200 and 100 pcs per packing bag 10 packing bags per inner carton total 10 000 pcs per inner carton 8 inner cartons per outer carton total 80 000 pcs per outer carton in every sh ipping lot, only the last pack will be non - full packing part no. : ltl1 n h s j4 d page : 5 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y bin code list for reference luminous intensity unit : mcd @20ma bin code min. max. jk 240 400 l m 400 680 np 680 1150 note: tolerance of each bin limit is 15% dominant wavelength unit : nm @20ma bin code min. max. h16 586.0 588.0 h17 588.0 590.0 h18 590.0 592.0 h19 592.0 594.0 note: tolerance of each bin limit is 1nm part no. : ltl1 n h s j4 d page : 6 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y cautions 1. application the leds described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).consult liteons sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the leds may directly jeopardize life or health (such as in aviation, t ransportation, traffic control equipment, medical and life support systems and safety devices). 2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative humidity. it is recommended that leds out of their original packa ging are used within three months. for extended storage out of their original packaging, it is recommended that the leds be stored in a sealed container with appropriate desiccant or in desiccators with nitrogen ambient. 3. cleaning use alcohol - based clean ing solvents such as isopropyl alcohol to clean the leds if necessary. 4. lead forming & assembly during lead forming, the leads should be bent at a point at least 3mm from the base of led lens. do not use the base of the lead frame as a fulcrum during fo rming. lead forming must be done before soldering, at normal temperature. during assembly on pcb, use minimum clinch force possible to avoid excessive mechanical stress. 5. soldering when soldering, leave a minimum of 2mm clearance from the base of the l ens to the soldering point. dipping the lens into the solder must be avoided. do not apply any external stress to the lead frame during soldering while the led is at high temperature. recommended soldering conditions : soldering iron wave soldering temperature soldering time 3 5 0c max. 3 sec. max. (one time only) pre - heat pre - heat time solder wave soldering time 100c max. 60 sec. max. 260c max. 5 sec. max. note: excessive soldering temperature and/or time might result in deformation of the led lens or catastrophic failure of the led. ir reflow is not suitable process for through hole type led lamp product. part no. : ltl1 n h s j4 d page : 7 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y 6. drive method an led is a current - operated device. in order to ensure intensity uniformity on multiple leds connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each led as shown in circu it a below. circuit model a circuit model b (a) recommended circuit (b) the brightness of each led might appear different due to the differences i n the i - v characteristics of those leds 7. esd (electrostatic discharge) static electricity or power surge will damage the led. suggestions to prevent esd damage: ? use a conductive wrist band or anti - electrostatic glove when handling these leds ? all devices, equipment, and machinery must be properly grounded ? work tables, storage racks, etc. should be properly grounded ? use ion blower to neutralize the static charge which might have built up on surface of the leds plastic lens as a result of fricti on between leds during storage and handing part no. : ltl1 n h s j4 d page : 8 of 10 bns - od - c131/a4 led led
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y suggested checking list : training and certification 1. everyone working in a static - safe area is esd - certified? 2. training records kept and re - certification dates monitored? static - safe workstation & work areas 1. static - safe workstation or work - areas have esd signs? 2. all surfaces and objects at all static - safe workstation and within 1 ft measure less than 100v? 3. al l ionizer activated, positioned towards the units? 4. each work surface mats grounding is good? personnel grounding 1. every person (including visitors) handling esd sensitive (esds) items wear wrist strap, heel strap or conductive shoes with conductiv e flooring? 2. if conductive footwear used, conductive flooring also present where operator stand or walk? 3. garments, hairs or anything closer than 1 ft to esd items measure less than 100v*? 4. every wrist strap or heel strap/conductive shoes check ed daily and result recorded for all dls? 5. all wrist strap or heel strap checkers calibration up to date? note: *50v for blue led. device handling 1. every esds items identified by eia - 471 labels on item or packaging? 2. all esds items compl etely inside properly closed static - shielding containers when not at static - safe workstation? 3. no static charge generators (e.g. plastics) inside shielding containers with esds items? 4. all flexible conductive and dissipative package materials inspected before reuse or recycle? others 1. audit result reported to entity esd control coordinator? 2. corrective action from previous audits completed? 3. are audit records complete and on file? part no. : ltl1 n h s j4 d page : 9 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y 8 . reliability test classification test item test condition reference standard endurance test operation life ta= under room temperature as per dat a sheet maximum rating test time= 1000hrs mil - std - 750d:1026 mil - std - 883g:1005 high temperature high humidity storage ta= 60 c rh= 90% test time= 240hrs mil - std - 202g:103b jeita ed - 4701:100 103 high temperature storage ta= 1055 c test time= 1000hrs mil - std - 750d:1031 mil - std - 883g:1008 jeita ed - 4701:200 201 low temperature storage ta= - 555 c test time=1000hrs jeita ed - 4701:200 202 environmental test temperature cycling 100 c c c c 30mins 5mins 30mins 5mins 3 0 cycles mil - std - 750d:1051 mil - std - 883g:1010 jeita ed - 4701:100 105 jesd22 - a104c thermal shock 105 5 c c 5 c 15mins ( ) mil - st d - 750d:1056 mil - std - 883g:1011 mil - std - 202g: 107g jesd22 - a106b solder resistance t.sol = 260 5 c max. dwell time = 10 1 sec mil - std - 750d:2031 jeita ed - 4701:300 302 solderability t. sol = 245 5 c dwell time= 5 0.5 sec ( free solder , coverage 95% of ) mil - std - 750d:2026 mil - std - 883g:2003 mil - std - 202g: 208h ipc/eia j - std - 002 soldering iron t. sol = 350 5 c dwell time= 3.5 0.5 sec mil - std - 202g: 208h jeita ed - 4701:300 302 9. others the appearance and specifications of the product may be modified for improvement, without prior notice. part no. : ltl1 n h s j4 d page : 10 of 10 bns - od - c131/a4

▲Up To Search▲

Price & Availability of LTL1NHSJ4D

	To Download LTL1NHSJ4D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .