mic2775 micro - power voltage supervisor ittybitty ? ittybitty is a registered trademark of micrel, inc . micrel inc. ? 2180 fortune drive ? san jose, ca 95131 ? usa ? tel +1 (408) 944 - 0800 ? fax + 1 (408) 474 - 1000 ? http://www.micrel.com march 23 , 2015 revision 4.0 general description the mic2775 is a power supply supervisor that provides undervoltage monitoring, manual reset capability, and power - on reset generation in a compact 5 - pin sot package. features include an undervoltage detector, a delay generator, a manual reset input, and both active - high and active - low reset outputs. the undervoltage detector compares v dd against a fixed threshold. ten factory - programmed thresholds are availabl e. the reset outputs are asserted for no less than 140ms at power - on and any time the input voltage drops below the reference voltage. it remains asserted for the timeout period after the input voltage subsequently rises back above the threshold boundary. a reset can be generated at any time by asserting the manual reset input, /mr. this reset output will remain active at least 140ms after the release of /mr. the /mr input can also be used to daisy - chain the mic2775 onto existing power monitoring circuitry or other supervisors. hysteresis is included to prevent chattering due to noise. typical suppy current is a n ultra - low 3.5 a. datasheets and support documentation are available on micrel?s web site at : www.micrel.com . features ? monitors power supply for undervoltage conditions ? choice of factory - programmed thresholds ? generates 140ms (minimum) power - on reset pulse ? manual reset capability ? both active - high and active - low reset outputs ? /rst output valid down to 1.2v ? ultra - lo w supply current, 3.5 a typical ? rejects brief input transients ? no external components ? for extended temperature range see micrel ?s max825 ? ittybitty ? 5 - pin sot - 23 package applications ? monitoring processor core and input/output voltages ? computer systems ? pdas, handheld pcs ? embedded controllers ? telecommunications systems ? power supplies typical application
micrel, inc. mic2775 march 23 , 2015 2 revision 4.0 ordering information part number ( 1 , 2 ) marking ( 1 , 3 ) junction temperature range package ( 4 ) mic2775 - xxym5 uj xx ? 40 c to +85c sot -23-5 note: 1. xx = voltage code, see part numbering conventions below. there are ten standard versions available with an order increment of 3,000 pieces. samples of standard versions are normally available from stock. contact factory for information on no n - standard versions. available in tape - and- reel only. 2. order entry part number add a space, then tr. example: mic2775 - 22ym5 tr. 3. underbar (__) symbol may not be to scale . 4. standard reel sot - 23: reel diameter is 7 inches, hub diameter is 2 inches, width is 8mm . part numbering conventions
micrel, inc. mic2775 march 23 , 2015 3 revision 4.0 pin configuration sot -23- 5 (m5) (top view) pin description pin number pin name pin function 1 /rst digital (output): asserted low whenever v dd falls below the reference voltage. it will remain asserted for no less than 140ms after v dd returns above the threshold limit. 2 gnd ground . 3 rst digital (output): asserted high whenever v dd falls below the reference voltage. it will remain asserted for no less than 140ms after v dd returns above the threshold limit. 4 /mr digital (input): driving this pin low initiates an immediate and unconditional reset. assuming v dd is above the threshold when /mr is released (returns high), the reset output will be de - asserted no less than 140ms later. /mr has an internal pull - up to v dd and may be left open if unused. 5 vdd analog (input): power supply input and the voltage being monitored.
micrel, inc. mic2775 march 23 , 2015 4 revision 4.0 absolute maximum ratings ( 5 ) supply voltage (v dd ) .................................... ? 0.3v to + 7.0 v output voltage (v /mr ) ................................... ? 0.3v to +7.0v rst, (/rst) current ................................................... 20ma storage temperature (t s ) ......................... ? 65c to +150c esd rating ( 7) ............................................................... 1.5 kv operating ratings ( 6 ) supply voltage (v dd ) .................................... + 1.5 v to + 5.5 v input voltage (v /mr ) ...................................... ? 0.3v to +6.0v ambient temperature (t a ) .......................... ? 40c to +85c package thermal resistance ( ja ) ........................ 256 c/w electrical characteristics ( 8 ) t a = 25c, bold values indicate ? 40c t a +85c, unless noted. symbol parameter condition min . typ . max . units i dd supply current v dd = v th + 1.6%, /mr, rst, /rst open, 3.5 a vdd voltage threshold undervoltage threshold on vdd v th - 1.5% v th v th + 1.5% v v hyst hysteresis voltage 1 % rst, /rst outputs t prop propagation delay v dd = v th + 1.5% + 100mv to v dd = v th ? 1.5% - 100mv 20 s t rst reset pulse width 140 280 ms v ol rst or /rst output voltage low i sink = 1.6ma; v dd 1.6v 0.3 v i sink = 100 a; v dd 1.2v; note 9 0.3 v v oh rst or /rst output voltage high i s ource = 500 a; v dd 1.5v 0.8v dd v i source = 10 a; v dd 1.2v; note 9 0.8v dd v /mr input v ih input high voltage 0.7 v dd v v il input low voltage 0.3 v dd v t prop propagation delay from v /mr < (v il ? 100mv) 5 s t min minimum input pulse width reset occurs, v /mr < v il 33 ns i pu internal pull - up current 100 na i in input current, /mr v /mr < v il 100 na notes: 5. exceeding the absolute maximum ratings may damage the device. 6. the device is not guaranteed to function outside its operating ratings. 7. devices are esd sensitive. handling precautions are recommended. human body model, 1.5k ? in series with 100pf. 8. specification for packaged product only . 9. v dd operating range is 1.5v to 5.5v. output is guaranteed to be asserted down to v dd = 1.2v.
micrel, inc. mic2775 march 23 , 2015 5 revision 4.0 timing di agram note: propagation delays not shown for clarity. a = the mic2775 ignores very brief transients. see the application information section for details.
micrel, inc. mic2775 march 23 , 2015 6 revision 4.0 functional diagram funct ional description vdd input the vdd pin is both the power supply terminal and a monitored input voltage. the voltage at this pin is continually compared against the internal reference. the trip - point at which a reset occurs is factory - programmed. a reset is triggered if and when v dd falls below the trip - point. hysteresis is employed to prevent chattering due to noise. the comparator on the vdd input is relatively immune to very brief negative - going transients. rst, /rst reset outputs typically, the mic2775 is used to monitor the power supply of intelligent circuits such as microcontrollers and microprocessors. by connecting the appropriate reset output of an mic2775 to the reset input of a c or p, the processor will be properly reset at power - on, power - down, and brown - out conditions. in addition, asserting /mr, the manual reset input, will activate the reset function. the reset outputs are asserted any time /mr is asserted or if v dd drops below the threshold voltage. the reset outputs remain asserted for t rst(min) after v dd subsequent ly returns above the threshold boundary and/or /mr is released. a reset pulse is also generated at power - on. hysteresis is included in the comparator to prevent chattering of the outputs due to noise. /mr, manual reset input the ability to initiate a res et via external logic or a manual switch is provided in addition to the mic2775?s automatic supervisory functions. driving the /m r input to a logic - low causes an immediate and unconditional reset to occur. assuming v dd is within tolerance when /mr is relea sed (returns high), the reset outputs will be de - asserted no less than t rst later. /mr may be driven by a logic signal or mechanical switch. typically, a momentary push - button switch is connected such that /mr is shorted to ground when the switch contact close. the switch may be connected directly between /mr and gnd. /mr has an internal 100na pull - up current to vdd and may be left open if unused.
micrel, inc. mic2775 march 23 , 2015 7 revision 4.0 application information ensuring proper operation at low supply at v dd levels below 1.2v, the mic2775?s /rst output cannot turn on sufficiently to produce a valid logic - low on /rst. in this situation, circuits driven by /rst could be allowed to float, causing undesired operation. in most cases, however, it is expected that the circuits driven by the mic2775 will be similarly inoperative at v dd 1.2v. if a given application requires tha t /rst be valid below v dd = 1.2v, this can be accomplished by adding a pull - down resistor to the /rst output. a value or 100k ? is recommended as this is usually an acceptable compromise of quiescent current and pull - down current. the resistor?s value is no t critical, however. see figure 1. figure 1 . mic2775 valid /rst below 1.2v the statements above also apply to the mic2775?s rst output. that is, to ensure valid rst signal levels when v dd < 1.2v, a pull - up resistor (as opposed to a pull - down) should be added to the rst output. a value or 100k ? is typical for this application, as well. see figure 2. figure 2 . mic2775 valid rst below 1.2v transient response the mic2775 is inherently immune to very short negative - going glitches. very brief transients may exceed the voltage threshold without tripping the output. in general, as shown in figure 3, the narrower the transient, the deeper the threshold overdrive that will be ignored by the mic2775. the gra ph represents the typical allowable transient duration for a given amount of threshold overdrive that will not generate a reset. figure 3 . typical vdd transient response
micrel, inc. mic2775 march 23 , 2015 8 revision 4.0 package information a nd recommended landing pattern ( 10) sot -23-5 (m5 ) note: 10. package information is correct as of the publication date. for updates and most current information, go to www.micrel.com .
micrel, inc. mic2775 march 23 , 2015 9 revision 4.0 micrel, inc. 2180 fortune drive san jose, ca 9513 1 usa tel +1 (408) 944 - 0800 fax +1 (408) 474- 1000 web http://www.micrel.com micrel, inc. is a leading global manufacturer of ic solutions for the worldwide high pe rformance linear and power, lan, and timing & com munications markets. the company?s products include advanced mixed - signal, analog & power semiconductors; high - performance communication, clock managemen t, mems - based clock oscillators & crystal - less clock generators, ethernet switch es, and physical layer transceiver ics. company customers include leading manufacturers of enterprise, consumer, industrial, mobile, telecommunications, automotive, and comp uter products. corporation headquarters and state - of - the - art wafer fabrication faci lities are located in san jose, ca, with regional sales and support offices and advanced technology design centers situated throughout the americas, europe , and asia. additionally , the company maintains an extensive network of distributors and reps worldw ide. micrel makes no representations or warranties with respect to the accuracy or completeness of the inf ormation furnished in this data sheet. this information is not intended as a warranty and micrel does not assume responsibility for its use. micrel r eserves the right to change circuitry, specifications and descriptions at any time without notice. no license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. e xcept as provided in micrel?s terms and conditions of sale for such products, micrel assumes no liability whatsoever, and micrel disclaims any express or implied warranty relating to the sale and/or use of micrel products including liability or warranties relating to fitnes s for a particular purpose, merchantability, or infringement of any patent, copyright , or other intellectual property right. micrel products are not designed or authorized for use as components in life support appliances, devices or systems where mal funct ion of a product can reasonably be expected to result in personal injury. life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be re asonably expected to result in a significant injury to the user. a purchaser?s use or sale of micrel products for use in life support appliances, devices or systems is a purchaser?s own risk a nd purchaser agrees to fully indemnify micrel for any damages re sulting from such use or sale. ? 20 00 micrel, incorporated.
|
