lga c series 15 - 100 watts total power: 15 - 100 w # of outputs: single special features ? 3, 6, 10 and 20 a output current rating ? wide input voltage range; up to 14 v ? adjustable output voltage; 0.59-5.1 v ? excellent transient response ? high effciency ? output margining ? power enable ? minimal airfow requirement ? termination voltage capability ? ultra compact profle and footprint ? rohs compliant ? remote sense ? termination voltage capability safety ? designed to meet en60950 ? international standards for solderability: j-std-002b iec-60068-2-58 electrical specifcations output 3/6/10 a models 20 a model output voltage see page 3 0.59 - 5.1 v output setpoint accuracy 0.1% trim resistors 1.0% line regulation 0.2% load regulation 0.5% max current max power 15/30/50 w 100 w overshoot at turn-on 0% undershoot at turn-off 0 mv ripple and noise 5 hz to 20 mhz see note 1 v in = 5 v, v out = 2.5 v 20/25/30 mv 30 mv transient response see notes 1 and 2 v in = 5 v, v out = 2.5 v 100/160/160 mv 15 s recovery to within regulation band 1175 mv 15 s recovery to within regulation band input input voltage range 3 3 - 14 vdc 4.5 - 14 vdc input current enable on at (0 a) enable off 50 ma 5 ma start-up time power up enable on/off 3 ms 2 ms general effciency v in = 5 v out , v o = 2.5 v, i out = 50% i max 92% typ. 92% typ. switching frequency 1 mhz 800 khz material fammability ul94v-0 mtbf 12 v @ 40 c 100% load bellcore 332 > 20,000,000 hours coplanarity 150 m thermal performance see technical reference note operating ambient non-operating ambient -40 c to +85 c -40 c to +125 c data sheet power
lga - htsk - kit - xxx lga xx c - 00 sadj x j ordering information standard model numbers output power (max.) input voltage output voltage output current efficiency (typical) regulation min max min max lga03c-00sadjj 15 w 3 - 14.0 vdc 0.59 - 5.1 vdc 0 a 3 a 92% 0.2% 0.5% lga06c-00sadjj 30 w 3 - 14.0 vdc 0.59 - 5.1 vdc 0 a 6 a 92% 0.2% 0.5% lga10c-00sadjj 50 w 3 - 14.0 vdc 0.59 - 5.1 vdc 0 a 10 a 92% 0.2% 0.5% lga20c-01sadjj 100 w 4.5 - 14.0 vdc 0.59 - 5.1 vdc 0 a 20 a 91% 0.2% 0.5% electrical specifcations protection short circuit hiccup, non-latching overvoltage hiccup, non-latching mininum recommended system capacitance 3/6/10 a model 20 a model short circuit 1 f 10 f product family rated output current rated output current 03 = 3 amp 06 = 6 amp 10 = 10 amp 20 = 20 amp performance performance c = cost optimized type of output type of output single adjustable output input voltage input voltage 00 = 3 - 14.0 v 01 = 4.5 - 14.0 v rohs compliance rohs compliance j = pb free (rohs 6/6 compliant) model number system with options options options x = various options (see sales rep) heatsink number system with options product family land grid array product heatsink purpose heatsink and adhesive height* total height (lga20 + heatsink) 045 = 0.45" 048 = 0.48" 050 = 0.50" * height is the total height of the lga20c-00sadjj with heatsink attached. lga c series data sheet
application equations 5-8 9-10 21 1-4 14 lga c series enable on/of f v in gnd r trim c in r l o a d v out c out 24 15 12 13 r mar gin +sense -sense r uvlo mar gin contr ol 23 r ofs- r ofs+ 22 power good gnd setting margin control setting output voltage setting under voltage lock out C 20 a models setting under voltage lock out C 3, 6, 10 a models to margin the output up, pull the margin control pin high. to margin down, pull the margin control pin low. if the pin is left foating, the feature is disabled. the maximum margining range is 33% of the oputput default voltage setting, with maximum output at 5.5 v v margin_up = 0.1182 * r margin * r trim + 2k r ofs + r trim v margin_down = 0.1182 * r margin * r trim + 2k r ofs - r trim default output voltage: 0.591 v the outut voltage may be adjusted with a resistor placed between the "trim" and "-sense" pin. the formula for calcuating the value of this resistor is: r trim (k) = 1.182 v out - 0.591 see technical reference note for other trimming methods. default turn-on voltage: 4.3 v (300 mv hysteresis) the turn-on voltage may be adjusted with a resistor placed between the enable and ground pins. the formula for calculating the value of this resistor is: r uvlo (k) = 30.1 * 4.22 (8.577 * v turn_on ) - 34.32 *only use with open collector device *do not drive pin with a voltage default turn-on voltage: 2.9 v (300 mv hysteresis) the turn-on voltage may be adjusted with a resistor placed between the enable and ground pins. the formula for calculating the value of this resistor is: r uvlo (k) = 14.81 * 6.81 (6.81 * v turn_on ) - 18.16 *only use with open collector device *do not drive pin with a voltage notes: 1 ese s e eoee sste te 2 t 10 a s12 no 25 c o e 50 o 100 3 te t te s te 1 external input fusing is recommended. lga c series data sheet
lga3-20c ds 03nov2015 mechanical drawing and footprint tolerance note: 0.010 (0.25) recommended system board footprint 0 (0) 0.125 (3.18) 0.295 (7.50) 0.435 (11.05) 0.570 (14.48) 0.690 (17.53) 0 (0) 0.387 (9.83) 0.432 (10.97) 0.477 (12.12) 0.522 (13.26) 0.567 (14.40) 0.612 (15.55) 0 (0) 0.126 (3.20) 0.272 (6.91) 0.418 (10.62) 0.564 (14.33) 0.690 (17.53) 0 (0) 0.220 (5.59) 0.269 (6.83) 0.318 (8.08) 0.367 (9.32) 0.416 (10.57) 0.465 (11.81) 0.514 (13.06) 0.563 (14.30) 0.612 (15.54) module outline 2x .120 x .110 8x .120 x .120 14x .025 x .025 pin 16 pin 24 pin 10 pin 9 pin 5 pin 1 pin 15 pin 4 pin 8 pin 11 keep out area 0.114" x 0.104" 2x 0.114" x 0.114" 8x 0.024" x.024" 13x 0 (0) 0.045 (1.14) 0.090 (2.29) 0.135 (3.43) 0.180 (4.57) 0.225 (5.72) 0.317 (8.05) 0.487 (12.37) 0.042 (1.07) 0.177 (4.50) 0.000 (0) 0.048 (1.22) 0.049 (1.24) 0.098 (2.49) 0.147 (3.73) 0.194 (4.93) 0.196 (4.98) 0.245 (6.22) 0.294 (7.47) 0.343 (8.71) 0.392 (9.96) 0.487 (12.37) 0.340 (8.64) 0.104 (2.64) 0.114 (2.90) 0.114 (2.90) 0.114 (2.90) 0.024 (0.61) 0.024 (0.61) recommended solder paste stencil s e c t io n a - a s c a l e 4 : 1 2 . 5 9 . 1 0 2 r e f .0 0 3 0 . 51 0.0 8 . 0 2 0 . 0 3 1 0 . 7 9 p c b r e f . 1 3 9 3 . 5 3 m a x a a 1 6.5 1 . 6 5 0 m a x . 6 5 0 16. 5 1 m a x - d c b a a b c d s c a l e : x = x s i z e c a d f i l e : d w g . n o . b s h e e t 1 o f 5 l g a 1 0 tl a a p p r o v a l s d r a w n e n g i n e e r u n l e s s o t h e r w i s e s p e c i f i e d d i m e n s i o n s a r e i n i n c h e s t o l e r a n c e s : h o l e t o l e r a n c e : 2 p l a c e 3 p l a c e a n g l e s . 0 3 m a t e r i a l f i n i s h - - 1 2 3 4 5 6 7 8 8 6 7 5 4 3 2 1 p h . 9 5 2 - 9 4 1 - 1 1 0 0 r e v . p r o j e c t u s e d o n : 7 0 9 1 3 2 3 -00 0 0 t i t l e : b l g a 1 0 c- 0 0 sa d j j e de n p ra i ri e , m n 5 5 4 3 3 e m e rs o n n e t wo rk p o we r p r o j e c t i o n a n g l e d a t e . 0 1 5 t h i r d 1 . 0 0 5 m a t t kre t m a n m a t t kre t m a n 1 0 a p r 0 9 1 0 a p r 0 9 d e t a c h e d l i s t n ot e : 1 . 9 30 0 1 6 1 - 00 00 p ac k ag i n g a n d m ate r i a l h an d l i n g p r o c e d u r e . 2. c os m eti c an d wor k m an s h i p p e r 9 3001 52- 0000. 3. l ab e l s h ow n f or p l ac e m e n t r e f e r e n c e on l y . .01 a a p a r t n u m b e r r e v d e s c r i p t i o n d r a f t d a t e 7 0 9 1 3 2 3 - 000 0 a r e l e a s e f o r p r o d u c t i o n m a t t k r e t m a n 0 4 / 1 0 / 0 9 7 0 9 1 3 2 3 - 000 0 b u p d a t e t o p a r a l l e l i s m s p e c m a t t k r e t m a n 0 5 / 2 6 / 0 9 r e v i s i o n r e c o r d a s e c t io n a - a s c a l e 4 : 1 2 . 5 9 . 1 0 2 r e f .0 0 3 0 . 51 0.0 8 . 0 2 0 . 0 3 1 0 . 7 9 p c b r e f . 1 3 9 3 . 5 3 m a x a a 1 6.5 1 . 6 5 0 m a x . 6 5 0 16. 5 1 m a x - d c b a a b c d s c a l e : x = x s i z e c a d f i l e : d w g . n o . b s h e e t 1 o f 5 l g a 1 0 tl a a p p r o v a l s d r a w n e n g i n e e r u n l e s s o t h e r w i s e s p e c i f i e d d i m e n s i o n s a r e i n i n c h e s t o l e r a n c e s : h o l e t o l e r a n c e : 2 p l a c e 3 p l a c e a n g l e s . 0 3 m a t e r i a l f i n i s h - - 1 2 3 4 5 6 7 8 8 6 7 5 4 3 2 1 p h . 9 5 2 - 9 4 1 - 1 1 0 0 r e v . p r o j e c t u s e d o n : 7 0 9 1 3 2 3 -00 0 0 t i t l e : b l g a 1 0 c- 0 0 sa d j j e de n p ra i ri e , m n 5 5 4 3 3 e m e rs o n n e t wo rk p o we r p r o j e c t i o n a n g l e d a t e . 0 1 5 t h i r d 1 . 0 0 5 m a t t kre t m a n m a t t kre t m a n 1 0 a p r 0 9 1 0 a p r 0 9 d e t a c h e d l i s t n ot e : 1 . 9 30 0 1 6 1 - 00 00 p ac k ag i n g a n d m ate r i a l h an d l i n g p r o c e d u r e . 2. c os m eti c an d wor k m an s h i p p e r 9 3001 52- 0000. 3. l ab e l s h ow n f or p l ac e m e n t r e f e r e n c e on l y . .01 a a p a r t n u m b e r r e v d e s c r i p t i o n d r a f t d a t e 7 0 9 1 3 2 3 - 000 0 a r e l e a s e f o r p r o d u c t i o n m a t t k r e t m a n 0 4 / 1 0 / 0 9 7 0 9 1 3 2 3 - 000 0 b u p d a t e t o p a r a l l e l i s m s p e c m a t t k r e t m a n 0 5 / 2 6 / 0 9 r e v i s i o n r e c o r d component height model dim a in mm lga03 lga06 lga10 0.129 (3.27) lga20 0.210 (5.33) pin assignments single output 1 vout 2 vout 3 vout 4 vout 5 gnd 6 gnd 7 gnd 8 gnd 9 vin 10 vin 11 nc 12 - offset 13 + offset 14 - sense 15 + sense 16 nc 17 nc 18 nc 19 nc 20 nc 21 enable 22 power good 23 margin control 23 trim lga c series data sheet worldwide offices americas 2900 s.diablo way tempe, az 85282 usa +1 888 412 7832 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom +44 (0) 1384 842 211 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong +852 2176 3333 for more information: www.artesyn.com/power for support: productsupport.ep@artesyn.com www.artesyn.com artesyn embedded technologies, artesyn and the artesyn embedded technologies logo are trademarks and service marks of artesyn embedded technologies, inc. all other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. ? 2015 artesyn embedded technologies, inc. all rights reserved. for full legal terms and conditions, please visit www.artesyn.com/legal.
|
