View DS2431-W0J1_8444911.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

general description the ds2431 is a 1024-bit, 1-wire ? eeprom chip orga - nized as four memory pages of 256 bits each. data is written to an 8-byte scratchpad, verified, and then copied to the eeprom memory. as a special feature, the four memory pages can individually be write protected or put in eprom-emulation mode, where bits can only be changed from a 1 to a 0 state. the ds2431 communi - cates over the single-conductor 1-wire bus. the com - munication follows the standard 1-wire protocol. each device has its own unalterable and unique 64-bit rom registration number that is factory lasered into the chip. the registration number is used to address the device in a multidrop, 1-wire net environment. applications accessory/pcb identiication medical sensor calibration data storage analog sensor calibration including ieee p1451.4 smart sensors ink and toner print cartridge identiication after-market management of consumables beneits and features easily add traceability and relevant information to any individual system ? 1024 bits of eeprom memory partitioned into four pages of 256 bits ? individual memory pages can be permanently write protected or put in eprom-emulation mode (write to 0) ? switchpoint hysteresis and filtering to optimize performance in the presence of noise minimalist 1-wire interface lowers cost and interface complexity ? iec 1000-4-2 level 4 esd protection (8kv contact, 15kv air, typ) ? reads and writes over a wide voltage range from 2.8v to 5.25v from -40c to +85c ? communicates to host with a single digital signal at 15.4kbps or 125kbps pin configurations appear at end of data sheet. 1-wire is a registered trademark of maxim integrated products, inc. 19-4675; rev 15; 3/15 note: the leads of to-92 packages on tape and reel are formed to approximately 100-mil (2.54mm) spacing. for details, refer to the package outline drawing. + denotes a lead(pb)-free/rohs-compliant package. t&r = tape and reel. * ep = exposed pad. part temp range pin-package ds2431+ -40c to +85c 3 to-92 ds2431+t&r -40c to +85c 3 to-92 ds2431p+ -40c to +85c 6 tsoc ds2431p+t&r -40c to +85c 6 tsoc ds2431g+u -40c to +85c 2 sfn (6mm x 6mm) ds2431g+t&r -40c to +85c 2 sfn (6mm x 6mm)(2.5k pcs) ds2431ga+u -40c to +85c 2 sfn (3.5mm x 6.5mm) ds2431ga+t&r -40c to +85c 2 sfn (3.5mm x 6.5mm) (2.5k pcs) ds2431q+t&r -40c to +85c 6 tdfn-ep* (2.5k pcs) ds2431x-s+ -40c to +85c 3x3 ucspr (2.5k pcs) ds2431x+ -40c to +85c 3x3 ucspr (10k pcs) io r pup v cc c gnd ds2431 ds2431 1024-bit, 1-wire eeprom typical operating circuit ordering information downloaded from: http:///
io voltage range to gnd........................................-0.5v to +6v io sink current....................................................................20ma operating temperature range.............................-40c to +85c junction temperature ........................................................ +150c storage temperature range..............................-55c to +125c lead temperature (excluding ucsp, soldering, 10s).......+300c soldering temperature (reflow) to-92............................................................................+250c ail other packages, excluding sfn ............................... +260c (t a = -40c to +85c.) (note 1) parameter symbol conditions min typ max units io pin: general data 1-wire pullup voltage v pup (note 2) 2.8 5.25 v 1-wire pullup resistance r pup (notes 2, 3) 0.3 2.2 k? input capacitance c io (notes 4, 5) 1000 pf input load current i l io pin at v pup 0.05 6.7 a high-to-low switching threshold v tl (notes 5, 6, 7) 0.5 v pup - 1.8 v input low voltage v il (notes 2, 8) 0.5 v low-to-high switching threshold v th (notes 5, 6, 9) 1.0 v pup - 1.0 v switching hysteresis v hy (notes 5, 6, 10) 0.21 1.70 v output low voltage v ol at 4ma (note 11) 0.4 v recovery time (notes 2,12) t rec standard speed, r pup = 2.2k? 5 s overdrive speed, r pup = 2.2k? 2 overdrive speed, directly prior to reset pulse; r pup = 2.2k? 5 rising-edge hold-off time (notes 5, 13) t reh standard speed 0.5 5.0 s overdrive speed not applicable (0) time slot duration (notes 2, 14) t slot standard speed 65 s overdrive speed 8 io pin: 1-wire reset, presence-detect cycle reset low time (note 2) t rstl standard speed 480 640 s overdrive speed 48 80 presence-detect high time t pdh standard speed 15 60 s overdrive speed 2 6 presence-detect low time t pdl standard speed 60 240 s overdrive speed 8 24 presence-detect sample time (notes 2, 15) t msp standard speed 60 75 s overdrive speed 6 10 ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 2 absolute maximum ratings stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. these are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. electrical characteristics downloaded from: http:///
(t a = -40c to +85c.) (note 1) note 1: limits are 100% production tested at t a = +25c and/or t a = +85c. limits over the operating temperature range and rel - evant supply voltage range are guaranteed by design and characterization. typical values are not guaranteed. note 2: system requirement. note 3: maximum allowable pullup resistance is a function of the number of 1-wire devices in the system and 1-wire recovery times. the specified value here applies to systems with only one device and with the minimum 1-wire recovery times. for more heavily loaded systems, an active pullup such as that found in the ds2482-x00, ds2480b, or ds2490 may be required. note 4: maximum value represents the internal parasite capacitance when v pup is first applied. once the parasite capacitance is charged, it does not affect normal communication. note 5: guaranteed by design, characterization, and/or simulation only. not production tested. note 6: v tl , v th , and v hy are a function of the internal supply voltage, which is a function of v pup , r pup , 1-wire timing, and capacitive loading on io. lower v pup , higher r pup , shorter t rec , and heavier capacitive loading all lead to lower values of v tl , v th , and v hy . note 7: voltage below which, during a falling edge on io, a logic 0 is detected. note 8: the voltage on io must be less than or equal to v ilmax at all times the master is driving io to a logic 0 level. note 9: voltage above which, during a rising edge on io, a logic 1 is detected. note 10: after v th is crossed during a rising edge on io, the voltage on io must drop by at least v hy to be detected as logic 0. note 11: the i-v characteristic is linear for voltages less than 1v. note 12: applies to a single device attached to a 1-wire line. note 13: the earliest recognition of a negative edge is possible at t reh after v th has been reached on the preceding rising edge. note 14: defines maximum possible bit rate. equal to t w0lmin + t recmin . note 15: interval after t rstl during which a bus master can read a logic 0 on io if there is a ds2431 present. the power-up pres - ence detect pulse could be outside this interval, but will be complete within 2ms after power-up. note 16: numbers in bold are not in compliance with legacy 1-wire product standards. see the comparison table . note 17: in figure 11 represents the time required for the pullup circuitry to pull the voltage on io up f rom v il to v th . the actual maximum duration for the master to pull the line low is t w1lmax + t f - and t w0lmax + t f - , respectively. note 18: in figure 11 represents the time required for the pullup circuitry to pull the voltage on io up f rom v il to the input-high threshold of the bus master. the actual maximum duration for the master to pull the line low is t rlmax + t f . parameter symbol conditions min typ max units io pin: 1-wire write write-zero low time (notes 2, 16, 17) t w0l standard speed 60 120 s overdrive speed, v pup > 4.5v 5 15.5 overdrive speed 6 15.5 write-one low time (notes 2, 17) t w1l standard speed 1 15 s overdrive speed 1 2 io pin: 1-wire read read low time (notes 2, 18) t rl standard speed 5 15 - d s overdrive speed 1 2 - d read sample time (notes 2, 18) t msr standard speed t rl + d 15 s overdrive speed t rl + d 2 eeprom programming current i prog (notes 5, 19) 0.8 ma programming time t prog (notes 20, 21) 10 ms write/erase cycles (endurance) (notes 22, 23) n cy at +25c 200k at +85c (worst case) 50k data retention(notes 24, 25, 26) t dr at +85c (worst case) 40 years ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 3 electrical characteristics (continued) downloaded from: http:///
note 19: current drawn from io during the eeprom programming interval. the pullup circuit on io during the programming interval should be such that the voltage at io is greater than or equal to v pupmin . if v pup in the system is close to v pupmin , a low-impedance bypass of r pup , which can be activated during programming, may need to be added. note 20: interval begins t rehmax after the trailing rising edge on io for the last time slot of the e/s byte for a valid copy scratchpad sequence. interval ends once the devices self-timed eeprom programming cycle is complete and the current drawn by the device has returned from i prog to i l . note 21: t prog for units branded version a1 is 12.5ms. t prog for units branded version a2 and later is 10ms. note 22: write-cycle endurance is degraded as t a increases. note 23: not 100% production tested; guaranteed by reliability monitor sampling. note 24: data retention is degraded as t a increases. note 25: guaranteed by 100% production test at elevated temperature for a shorter time; equivalence of this production test to the data sheet limit at operating temperature range is established by reliability testing. note 26: eeprom writes can become nonfunctional after the data-retention time is exceeded. long-term storage at elevated tem - peratures is not recommended; the device can lose its write capability after 10 years at +125c or 40 years at +85c. * intentional change; longer recovery time requirement due to modified 1-wire front-end. note: numbers in bold are not in compliance with legacy 1-wire product standards. parameter legacy values ds2431 values standard speed (s) overdrive speed (s) standard speed (s) overdrive speed (s) min max min max min max min max t slot (including t rec ) 61 (undeined) 7 (undeined) 65* (undeined) 8* (undeined) t rstl 480 (undeined) 48 80 480 640 48 80 t pdh 15 60 2 6 15 60 2 6 t pdl 60 240 8 24 60 240 8 24 t w0l 60 120 6 16 60 120 6 15.5 ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 4 comparison table downloaded from: http:///
detailed description the ds2431 combines 1024 bits of eeprom, an 8-byte register/control page with up to 7 user read/write bytes, and a fully featured 1-wire interface in a single chip. each ds2431 has its own 64-bit rom registration number that is factory lasered into the chip to provide a guaranteed unique identity for absolute traceability. data is transferred serially through the 1-wire protocol, which requires only a single data lead and a ground return. the ds2431 has an additional memory area called the scratchpad that acts as a buffer when writing to the main memory or the register page. data is first written to the scratchpad from which it can be read back. after the data has been verified, a copy scratchpad command transfers the data to its final memory location. the ds2431 applications include accessory/pcb identification, medical sensor calibration data storage, analog sensor calibration including ieee p1451.4 smart sensors, ink and toner print cartridge identification, and after-market management of consumables. overview the block diagram in figure 1 shows the relationships between the major control and memory sections of the ds2431. the ds2431 has four main data components: 64-bit lasered rom, 64-bit scratchpad, four 32-byte pages of eeprom, and a 64-bit register page. figure 1. block diagram pin name function tsoc to-92 tdfn-ep sfn ucspr 3, 4, 5, 6 3 1, 4, 5, 6 a2, a3, c2, c3 n.c. not connected 2 2 2 1 c1 io 1-wire bus interface. open-drain signal that requires an external pullup resistor. 1 1 3 2 a1 gnd ground reference ep exposed pad (tdfn only). solder evenly to the boards ground plane for proper operation. refer to application note 3273: exposed pads: a brief introduction for additional information. memory function control unit data memory 4 pages of 256 bits each crc-16 generator 64-bit scratchpad 1-wire function control 64-bit lasered rom parasite power io register page 64 bits ds2431 ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 5 pin description downloaded from: http:///
the hierarchical structure of the 1-wire protocol is shown in figure 2. the bus master must first provide one of the seven rom function commands: read rom, match rom, search rom, skip rom, resume, overdrive-skip rom, or overdrive-match rom. upon completion of an overdrive-skip rom or overdrive-match rom command byte executed at standard speed, the device enters over - drive mode where all subsequent communication occurs at a higher speed. the protocol required for these rom function commands is described in figure 9. after a rom function command is successfully executed, the memory functions become accessible and the master can provide any one of the four memory function commands. the pro - tocol for these memory function commands is described in figure 7. all data is read and written least signifi - cant bit first . 64-bit lasered rom each ds2431 contains a unique rom code that is 64 bits long. the first 8 bits are a 1-wire family code. the next 48 bits are a unique serial number. the last 8 bits are a cyclic redundancy check (crc) of the first 56 bits. see figure 3 for details. the 1-wire crc is generated using a polyno - mial generator consisting of a shift register and xor gates as shown in figure 4. the polynomial is x 8 + x 5 + x 4 + 1. additional information about the 1-wire crc is available in application note 27: understanding and using cyclic redundancy checks with maxim ibutton ? products . the shift register bits are initialized to 0. then, starting with the least significant bit of the family code, one bit at a time is shifted in. after the 8th bit of the family code has been entered, the serial number is entered. after the last bit of the serial number has been entered, the shift reg - ister contains the crc value. shifting in the 8 bits of the crc returns the shift register to all 0s. figure 2. hierarchical structure for 1-wire protocol figure 3. 64-bit lasered rom ibutton is a registered trademark of maxim integrated products, inc. ds2431 command level: available commands: data field affected: read rom match rom search rom skip rom resume overdrive-skip rom overdrive-match rom 64-bit reg. #, rc-flag64-bit reg. #, rc-flag 64-bit reg. #, rc-flag rc-flag rc-flag rc-flag, od-flag 64-bit reg. #, rc-flag, od-flag 1-wire rom function commands (see figure 9) write scratchpadread scratchpad copy scratchpad read memory 64-bit scratchpad, flags64-bit scratchpad data memory, register page data memory, register page ds2431-specific memory function commands (see figure 7) msb 8-bit crc code 48-bit serial number msb msb lsb lsblsb 8-bit family code (2dh) msb lsb ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 6 downloaded from: http:///
memory access data memory and registers are located in a linear address space, as shown in figure 5. the data memory and the registers have unrestricted read access. the ds2431 eeprom array consists of 18 rows of 8 bytes each. the first 16 rows are divided equally into four memory pages (32 bytes each). these four pages are the primary data memory. each page can be individually set to open (unprotected), write protected, or eprom mode by set - ting the associated protection byte in the register row. as a factory default, the entire data memory is unprotected and its contents are undefined. the last two rows contain protection registers and reserved bytes. the register row consists of 4 protection control bytes, a copy-protection byte, the factory byte, and 2 user byte/manufacture id bytes. the manufacturer id can be a customer-supplied identification code that assists the application software in identifying the product the ds2431 is associated with. figure 4. 1-wire crc generator figure 5. memory map 1st stage 2nd stage 3rd stage 4th stage 7th stage 8th stage 6th stage 5th stage x 0 x 1 x 2 x 3 x 4 polynomial = x 8 + x 5 + x 4 + 1 input data x 5 x 6 x 7 x 8 address range type description protection codes 0000h to 001fh r/(w) data memory page 0 0020h to 003fh r/(w) data memory page 1 0040h to 005fh r/(w) data memory page 2 0060h to 007fh r/(w) data memory page 3 0080h* r/(w) protection control byte page 0 55h: write protect p0; aah: eprom mode p0; 55h or aah: write protect 80h 0081h* r/(w) protection control byte page 1 55h: write protect p1; aah: eprom mode p1; 55h or aah: write protect 81h 0082h* r/(w) protection control byte page 2 55h: write protect p2; aah: eprom mode p2; 55h or aah: write protect 82h 0083h* r/(w) protection control byte page 3 55h: write protect p3; aah: eprom mode p3; 55h or aah: write protect 83h 0084h* r/(w) copy protection byte 55h or aah: copy protect 0080h:008fh, and any write-protected pages 0085h r factory byte. set at factory. aah: write protect 85h, 86h, 87h; 55h: write protect 85h; unprotect 86h, 87h 0086h r/(w) user byte/manufacturer id 0087h r/(w) user byte/manufacturer id 0088h to 008fh reserved * once programmed to aah or 55h this address becomes read only. all other codes can be stored, but neither write protect the address nor activate any function . ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 7 downloaded from: http:///
contact the factory to set up and register a custom manu - facturer id. the last row is reserved for future use. it is undefined in terms of r/w functionality and should not be used. in addition to the main eeprom array, an 8-byte volatile scratchpad is included. writes to the eeprom array are a two-step process. first, data is written to the scratchpad and then copied into the main array. this allows the user to first verify the data written to the scratchpad prior to copying into the main array. the device only supports full row (8-byte) copy operations. for data in the scratchpad to be valid for a copy operation, the address supplied with a write scratchpad command must start on a row bound - ary, and 8 full bytes must be written into the scratchpad. the protection control registers determine how incom - ing data on a write scratchpad command is loaded into the scratchpad. a protection setting of 55h (write protect) causes the incoming data to be ignored and the target address main memory data to be loaded into the scratch - pad. a protection setting of aah (eprom mode) causes the logical and of incoming data and target address main memory data to be loaded into the scratchpad. any other protection control register setting leaves the associ - ated memory page open for unrestricted write access. note: for the eprom mode to function, the entire affected memory page must first be programmed to ffh. protection-control byte settings of 55h or aah also write protect the protection-control byte. the protection-control byte setting of 55h does not block the copy. this allows write-protected data to be refreshed (i.e., reprogrammed with the current data) in the device. the copy-protection byte is used for a higher level of security and should only be used after all other protection control bytes, user bytes, and write-protected pages are set to their final value. if the copy-protection byte is set to 55h or aah, all copy attempts to the register row and user-byte row are blocked. in addition, all copy attempts to write-protected main memory pages (i.e., refresh) are blocked. address registers and transfer status the ds2431 employs three address registers: ta1, ta2, and e/s (figure 6). these registers are common to many other 1-wire devices but operate slightly differently with the ds2431. registers ta1 and ta2 must be loaded with the target address to which the data is written or from which data is read. register e/s is a read-only transfer- status register used to verify data integrity with write com - mands. e/s bits e[2:0] are loaded with the incoming t[2:0] on a write scratchpad command and increment on each subsequent data byte. this is, in effect, a byte-ending off - set counter within the 8-byte scratchpad. bit 5 of the e/s register, called pf, is a logic 1 if the data in the scratchpad is not valid due to a loss of power or if the master sends fewer bytes than needed to reach the end of the scratch - pad. for a valid write to the scratchpad, t[2:0] must be 0 and the master must have sent 8 data bytes. bits 3, 4, and 6 have no function; they always read 0. the highest val - ued bit of the e/s register, called authorization accepted (aa), acts as a flag to indicate that the data stored in the scratchpad has already been copied to the target memory address. writing data to the scratchpad clears this flag. figure 6. address registers bit # 7 6 5 4 3 2 1 0 target address (ta1) t7 t6 t5 t4 t3 t2 t1 t0 target address (ta2) t15 t14 t13 t12 t11 t10 t9 t8 ending address with data status (e/s) (read only) aa 0 pf 0 0 e2 e1 e0 ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 8 downloaded from: http:///
writing with veriication to write data to the ds2431, the scratchpad must be used as intermediate storage. first, the master issues the write scratchpad command to specify the desired target address, followed by the data to be written to the scratchpad. note that copy scratchpad commands must be performed on 8-byte boundaries, i.e., the three lsbs of the target address (t2, t1, t0) must be equal to 000b. if t[2:0] are sent with nonzero values, the copy func - tion is blocked. under certain conditions (see the write scratchpad [0fh] section) the master receives an inverted crc-16 of the command, address (actual address sent), and data at the end of the write scratchpad command sequence. knowing this crc value, the master can compare it to the value it has calculated to decide if the communication was successful and proceed to the copy scratchpad command. if the master could not receive the crc-16, it should send the read scratchpad command to verify data integrity. as a preamble to the scratchpad data, the ds2431 repeats the target address ta1 and ta2 and sends the contents of the e/s register. if the pf flag is set, data did not arrive correctly in the scratchpad, or there was a loss of power since data was last written to the scratch - pad. the master does not need to continue reading; it can start a new trial to write data to the scratchpad. similarly, a set aa flag together with a cleared pf flag indicates that the device did not recognize the write command. if everything went correctly, both flags are cleared. now the master can continue reading and verifying every data byte. after the master has verified the data, it can send the copy scratchpad command, for example. this command must be followed exactly by the data of the three address registers, ta1, ta2, and e/s. the master should obtain the contents of these registers by reading the scratchpad. memory function commands the memory function flowchart (figure 7) describes the protocols necessary for accessing the memory of the ds2431. an example on how to use these functions to write to and read from the device is in the memory function example section. the communication between the master and the ds2431 takes place either at standard speed (default, od = 0) or at overdrive speed (od = 1). if not explicitly set into overdrive mode, the ds2431 assumes standard speed. write scratchpad [0fh] the write scratchpad command applies to the data memory and the writable addresses in the register page. for the scratchpad data to be valid for copying to the array, the user must perform a write scratchpad com - mand of 8 bytes starting at a valid row boundary. the write scratchpad command accepts invalid addresses and partial rows, but subsequent copy scratchpad com - mands are blocked. after issuing the write scratchpad command, the master must first provide the 2-byte target address, followed by the data to be written to the scratchpad. the data is writ - ten to the scratchpad starting at the byte offset of t[2:0]. the e/s bits e[2:0] are loaded with the starting byte offset and increment with each subsequent byte. effectively, e[2:0] is the byte offset of the last full byte written to the scratchpad. only full data bytes are accepted. when executing the write scratchpad command, the crc generator inside the ds2431 (figure 13) calculates a crc of the entire data stream, starting at the command code and ending at the last data byte as sent by the mas - ter. this crc is generated using the crc-16 polynomial by first clearing the crc generator and then shifting in the command code (0fh) of the write scratchpad command, the target addresses (ta1 and ta2), and all the data bytes. note that the crc-16 calculation is performed with the actual ta1 and ta2 and data sent by the master. the master can end the write scratchpad command at any time. however, if the end of the scratchpad is reached (e[2:0] = 111b), the master can send 16 read time slots and receive the crc generated by the ds2431. if a write scratchpad command is attempted to a write - protected location, the scratchpad is loaded with the data already existing in memory rather than the data transmitted. similarly, if the target address page is in eprom mode, the scratchpad is loaded with the bitwise logical and of the transmitted data and data already existing in memory. ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 9 downloaded from: http:///
figure 7a. memory function flowchart bus master tx memory function command bus master tx ta1 (t[7:0]), ta2 (t[15:8]) bus master rx ta1 (t[7:0]), ta2 (t[15:8]), and e/s byte bus master rx data byte from scratchpad master tx data byte to scratchpad applies only if the memory area is not protected. if write protected , the ds2431 copiesthe date byte from the target address into the scratchpad. if in eprom mode , the ds2431 loadsthe bitwise logical and of the transmitted byte and the data byte from the targeted address into the scratchpad. bus master rx "1"s ds2431 increments e[2:0] pf = 0 ds2431 sets pf = 1 clears aa = 0 sets e[2:0] = t[2:0] 0fh write scratchpad? ny n yn y y y n n master tx reset? e[2:0] = 7? t[2:0] = 0? master tx reset? ds2431 sets scratchpad byte counter = t[2:0] aah read scratchpad? n y ds2431 tx crc-16 of command, address, and data bytes as they were sent by the bus master bus master rx "1"s y n master tx reset? bus master rx crc-16 of command, address, e/s byte, and data bytes as sent by the ds2431 y n master tx reset? y byte counter = e[2:0]? from rom functions flowchart (figure 9) to rom functions flowchart (figure 9) ds2431 increments byte counter n to figure 7b from figure 7b ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 10 downloaded from: http:///
figure 7b. memory function flowchart (continued) bus master tx ta1 (t[7:0]), ta2 (t[15:8]) applicable to all r/wmemory locations. duration: t prog * * 1-wire idle high for power. ds2431 copies scratchpad data to address bus master rx "1"s aa = 1 bus master rx "1"s master tx reset? n y n n master tx reset? y master tx reset? bus master tx ta1 (t[7:0]), ta2 (t[15:8]) and e/s byte 55h copy scratchpad? n y y y n ds2431 tx "0" ds2431 tx "1" f0h read memory? n y y n auth. code match? y n y n n t[15:0] < 0090h? pf = 0? address < 90h? y copy protected? bus master rx "1"s master tx reset? n y ds2431 sets memory address = (t[15:0]) bus master rx data byte from memory address y nn master tx reset? address < 8fh? n y master tx reset? ds2431 increments address counter y to figure 7a from figure 7a ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 11 downloaded from: http:///
read scratchpad [aah]the read scratchpad command allows verifying the tar - get address and the integrity of the scratchpad data. after issuing the command code, the master begins reading. the first two bytes are the target address. the next byte is the ending offset/data status byte (e/s) followed by the scratchpad data, which may be different from what the master originally sent. this is of particular importance if the target address is within the register page or a page in either write-protection mode or eprom mode. see the write scratchpad [0fh] section for details. the master should read through the scratchpad (e[2:0] - t[2:0] + 1 bytes), after which it receives the inverted crc based on data as it was sent by the ds2431. if the master continues reading after the crc, all data is logic 1. copy scratchpad [55h] the copy scratchpad command is used to copy data from the scratchpad to writable memory sections. after issuing the copy scratchpad command, the master must provide a 3-byte authorization pattern, which should have been obtained by an immediately preceding read scratchpad command. this 3-byte pattern must exactly match the data contained in the three address registers (ta1, ta2, e/s, in that order). if the pattern matches, the target address is valid, the pf flag is not set, and the tar - get memory is not copy protected, then the aa flag is set and the copy begins. all 8 bytes of scratchpad contents are copied to the target memory location. the duration of the devices internal data transfer is t prog during which the voltage on the 1-wire bus must not fall below 2.8v. a pattern of alternating 0s and 1s are transmitted after the data has been copied until the master issues a reset pulse. if the pf flag is set or the target memory is copy protected, the copy does not begin and the aa flag is not set. read memory [f0h] the read memory command is the general function to read data from the ds2431. after issuing the command, the master must provide the 2-byte target address. after these 2 bytes, the master reads data beginning from the target address and can continue until address 008fh. if the master continues reading, the result is logic 1s. the devices internal ta1, ta2, e/s, and scratchpad contents are not affected by a read memory command. 1-wire bus system the 1-wire bus is a system that has a single bus master and one or more slaves. in all instances the ds2431 is a slave device. the bus master is typically a microcon - troller. the discussion of this bus system is broken down into three topics: hardware configuration, transaction sequence, and 1-wire signaling (signal types and timing). the 1-wire protocol defines bus transactions in terms of the bus state during specific time slots, which are initiated on the falling edge of sync pulses from the bus master. hardware coniguration the 1-wire bus has only a single line by definition; it is important that each device on the bus be able to drive it at the appropriate time. to facilitate this, each device attached to the 1-wire bus must have open-drain or three- state outputs. the 1-wire port of the ds2431 is open drain with an internal circuit equivalent to that shown in figure 8. a multidrop bus consists of a 1-wire bus with multiple slaves attached. the ds2431 supports both a standard and overdrive communication speed of 15.4kbps (max) and 125kbps (max), respectively. note that legacy 1-wire products support a standard communication speed of 16.3kbps and overdrive of 142kbps. the slightly reduced rates for the ds2431 are a result of additional recovery times, which in turn were driven by a 1-wire physical interface enhancement to improve noise immunity. the value of the pullup resistor primarily depends on the net - work size and load conditions. the ds2431 requires a pullup resistor of 2.2k (max) at any speed. the idle state for the 1-wire bus is high. if for any reason a transaction needs to be suspended, the bus must be left in the idle state if the transaction is to resume. if this does not occur and the bus is left low for more than 16s (overdrive speed) or more than 120s (standard speed), one or more devices on the bus could be reset. transaction sequence the protocol for accessing the ds2431 through the 1-wire port is as follows: initialization rom function command memory function command transaction/data ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 12 downloaded from: http:///
initialization all transactions on the 1-wire bus begin with an initializa - tion sequence. the initialization sequence consists of a reset pulse transmitted by the bus master followed by presence pulse(s) transmitted by the slave(s). the pres - ence pulse lets the bus master know that the ds2431 is on the bus and is ready to operate. for more details, see the 1-wire signaling section. 1-wire rom function commands once the bus master has detected a presence, it can issue one of the seven rom function commands that the ds2431 supports. all rom function commands are 8 bits long. a list of these commands follows (see the flowchart in figure 9). read rom [33h] the read rom command allows the bus master to read the ds2431s 8-bit family code, unique 48-bit serial num - ber, and 8-bit crc. this command can only be used if there is a single slave on the bus. if more than one slave is present on the bus, a data collision occurs when all slaves try to transmit at the same time (open drain pro - duces a wired-and result). the resultant family code and 48-bit serial number result in a mismatch of the crc. match rom [55h] the match rom command, followed by a 64-bit rom sequence, allows the bus master to address a specific ds2431 on a multidrop bus. only the ds2431 that exactly matches the 64-bit rom sequence responds to the sub - sequent memory function command. all other slaves wait for a reset pulse. this command can be used with a single device or multiple devices on the bus. search rom [f0h] when a system is initially brought up, the bus master might not know the number of devices on the 1-wire bus or their registration numbers. by taking advantage of the wired-and property of the bus, the master can use a process of elimination to identify the registration numbers of all slave devices. for each bit of the registra - tion number, starting with the least significant bit, the bus master issues a triplet of time slots. on the first slot, each slave device participating in the search outputs the true value of its registration number bit. on the second slot, each slave device participating in the search outputs the complemented value of its registration number bit. on the third slot, the master writes the true value of the bit to be selected. all slave devices that do not match the bit written by the master stop participating in the search. if both of the read bits are zero, the master knows that slave devices exist with both states of the bit. by choosing which state to write, the bus master branches in the rom code tree. after one complete pass, the bus master knows the registration number of a single device. additional passes identify the registration numbers of the remaining devices. refer to application note 187: 1-wire search algorithm for a detailed discussion, including an example. skip rom [cch] this command can save time in a single-drop bus sys - tem by allowing the bus master to access the memory functions without providing the 64-bit rom code. if more than one slave is present on the bus and, for example, a read command is issued following the skip rom com - mand, data collision occurs on the bus as multiple slaves transmit simultaneously (open-drain pulldowns produce a wired-and result). figure 8. hardware configuration rx r pup i l v pup bus master open-drain port pin 100 mosfet tx rxtx data ds2431 1-wire port rx = receive tx = transmit ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 13 downloaded from: http:///
figure 9a. rom functions flowchart ds2431 tx presence pulse bus master tx reset pulse bus master tx rom function command ds2431 tx crc byte ds2431 tx family code (1 byte) ds2431 tx serial number (6 bytes) rc = 0 master tx bit 0 rc = 0 rc = 0 rc = 0 od = 0 y y y yy y y y 33h read rom command? n 55h match rom command? bit 0 match? bit 0 match? n n n n n n n f0h search rom command? od reset pulse? n n cch skip rom command? n rc = 1 master tx bit 1 master tx bit 63 bit 1 match? bit 63 match? y y rc = 1 from memory functions flowchart (figure 7) to memory functions flowchart (figure 7) ds2431 tx bit 0 ds2431 tx bit 0 master tx bit 0 bit 1 match? bit 63 match? ds2431 tx bit 1 ds2431 tx bit 1 master tx bit 1 ds2431 tx bit 63 ds2431 tx bit 63 master tx bit 63 y to figure 9b to figure 9b from figure 9b from figure 9b ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 14 downloaded from: http:///
figure 9b. rom functions flowchart (continued) rc = 0; od = 1 rc = 0; od = 1 n bit 0 match? y n rc = 1? y a5h resume command? n y 3ch overdrive- skip rom? n y 69h overdrive- match rom? from figure 9afrom figure 9a to figure 9a to figure 9a n y y n master tx reset? y master tx reset? n bit 1 match? master tx bit 0 master tx bit 1 od = 0 n od = 0 n od = 0 y rc = 1 bit 63 match? master tx bit 63 y ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 15 downloaded from: http:///
resume [a5h] to maximize the data throughput in a multidrop environ - ment, the resume command is available. this command checks the status of the rc bit and, if it is set, directly transfers control to the memory function commands, similar to a skip rom command. the only way to set the rc bit is through successfully executing the match rom, search rom, or overdrive-match rom command. once the rc bit is set, the device can repeatedly be accessed through the resume command. accessing another device on the bus clears the rc bit, preventing two or more devices from simultaneously responding to the resume command. overdrive-skip rom [3ch] on a single-drop bus this command can save time by allowing the bus master to access the memory functions without providing the 64-bit rom code. unlike the normal skip rom command, the overdrive-skip rom command sets the ds2431 into the overdrive mode (od = 1). all communication following this command must occur at overdrive speed until a reset pulse of minimum 480s duration resets all devices on the bus to standard speed (od = 0). when issued on a multidrop bus, this command sets all overdrive-supporting devices into overdrive mode. to subsequently address a specific overdrive-supporting device, a reset pulse at overdrive speed must be issued followed by a match rom or search rom command sequence. this speeds up the time for the search pro - cess. if more than one slave supporting overdrive is pres - ent on the bus and the overdrive-skip rom command is followed by a read command, data collision occurs on the bus as multiple slaves transmit simultaneously (open- drain pulldowns produce a wired-and result). overdrive-match rom [69h] the overdrive-match rom command followed by a 64-bit rom sequence transmitted at overdrive speed allows the bus master to address a specific ds2431 on a multi - drop bus and to simultaneously set it in overdrive mode. only the ds2431 that exactly matches the 64-bit rom sequence responds to the subsequent memory function command. slaves already in overdrive mode from a previ - ous overdrive-skip rom or successful overdrive-match rom command remain in overdrive mode. all overdrive- capable slaves return to standard speed at the next reset pulse of minimum 480s duration. the overdrive-match rom command can be used with a single device or mul - tiple devices on the bus. 1-wire signaling the ds2431 requires strict protocols to ensure data integ - rity. the protocol consists of four types of signaling on one line: reset sequence with reset pulse and presence pulse, write-zero, write-one, and read-data. except for the presence pulse, the bus master initiates all falling edges. the ds2431 can communicate at two different speeds: standard speed and overdrive speed. if not explicitly set into the overdrive mode, the ds2431 communicates at standard speed. while in overdrive mode, the fast timing applies to all waveforms. to get from idle to active, the voltage on the 1-wire line needs to fall from v pup below the threshold v tl . to get from active to idle, the voltage needs to rise from v ilmax past the threshold v th . the time it takes for the voltage to make this rise is seen in figure 10 as , and its dura - tion depends on the pullup resistor (r pup ) used and the capacitance of the 1-wire network attached. the voltage v ilmax is relevant for the ds2431 when determining a logical level, not triggering any events. figure 10 shows the initialization sequence required to begin any communication with the ds2431. a reset pulse followed by a presence pulse indicates that the ds2431 is ready to receive data, given the correct rom and mem - ory function command. if the bus master uses slew-rate control on the falling edge, it must pull down the line for t rstl + t f to compensate for the edge. a t rstl duration of 480s or longer exits the overdrive mode, returning the device to standard speed. if the ds2431 is in overdrive mode and t rstl is no longer than 80s, the device remains in overdrive mode. if the device is in overdrive mode and t rstl is between 80s and 480s, the device resets, but the communication speed is undetermined. after the bus master has released the line it goes into receive mode. now the 1-wire bus is pulled to v pup through the pullup resistor or, in the case of a ds2482-x00 or ds2480b driver, through the active circuitry. when the threshold v th is crossed, the ds2431 waits for t pdh and then transmits a presence pulse by pulling the line low for t pdl . to detect a presence pulse, the master must test the logical state of the 1-wire line at t msp . the t rsth window must be at least the sum of t pdhmax , t pdlmax , and t recmin . immediately after t rsth is expired, the ds2431 is ready for data commu - nication. in a mixed population network, t rsth should be extended to minimum 480s at standard speed and 48s at overdrive speed to accommodate other 1-wire devices. ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 16 downloaded from: http:///
read/write time slots data communication with the ds2431 takes place in time slots that carry a single bit each. write time slots transport data from bus master to slave. read time slots transfer data from slave to master. figure 11 illustrates the defini - tions of the write and read time slots. all communication begins with the master pulling the data line low. as the voltage on the 1-wire line falls below the threshold v tl , the ds2431 starts its internal timing generator that determines when the data line is sampled during a write time slot and how long data is valid during a read time slot. master-to-slave for a write-one time slot, the voltage on the data line must have crossed the v th threshold before the write- one low time t w1lmax is expired. for a write-zero time slot, the voltage on the data line must stay below the v th threshold until the write-zero low time t w0lmin is expired. for the most reliable communication, the voltage on the data line should not exceed v ilmax during the entire t w0l or t w1l window. after the v th threshold has been crossed, the ds2431 needs a recovery time t rec before it is ready for the next time slot. slave-to-mastera read-data time slot begins like a write-one time slot. the voltage on the data line must remain below v tl until the read low time t rl is expired. during the t rl window, when responding with a 0, the ds2431 starts pulling the data line low; its internal timing generator determines when this pulldown ends and the voltage starts rising again. when responding with a 1, the ds2431 does not hold the data line low at all, and the voltage starts rising as soon as t rl is over. the sum of t rl + (rise time) on one side and the internal timing generator of the ds2431 on the other side define the master sampling window (t msrmin to t msrmax ), in which the master must perform a read from the data line. for the most reliable communication, t rl should be as short as permissible, and the master should read close to but no later than t msrmax . after reading from the data line, the master must wait until t slot is expired. this guarantees sufficient recovery time t rec for the ds2431 to get ready for the next time slot. note that t rec speci - fied herein applies only to a single ds2431 attached to a 1-wire line. for multidevice configurations, t rec must be extended to accommodate the additional 1-wire device input capacitance. alternatively, an interface that performs active pullup during the 1-wire recovery time such as the ds2482-x00 or ds2480b 1-wire line drivers can be used. figure 10. initialization procedure: reset and presence pulse resistor master ds2431 t rstl t pdl t rsth t pdh master tx "reset pulse" master rx "presence pulse" v pup v ihmaster v th v tl v ilmax 0v t f t rec t msp ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 17 downloaded from: http:///
figure 11. read/write timing diagrams resistor master resistor master resistor master ds2431 v pup v ihmaster v th v tl v ilmax 0v t f v pup v ihmaster v th v tl v ilmax 0v t f v pup v ihmaster v th v tl v ilmax 0v t f t slot t w1l t rec t slot t slot t w0l t rec master sampling window t rl t msr write-one time slotwrite-zero time slot read-data time slot ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 18 downloaded from: http:///
improved network behavior (switchpoint hysteresis) in a 1-wire environment, line termination is possible only during transients controlled by the bus master (1-wire driver). 1-wire networks, therefore, are susceptible to noise of various origins. depending on the physical size and topology of the network, reflections from end points and branch points can add up or cancel each other to some extent. such reflections are visible as glitches or ringing on the 1-wire communication line. noise coupled onto the 1-wire line from external sources can also result in signal glitching. a glitch during the rising edge of a time slot can cause a slave device to lose synchronization with the master and, consequently, result in a search rom command coming to a dead end or cause a device-spe - cific function command to abort. for better performance in network applications, the ds2431 uses a new 1-wire front-end, which makes it less sensitive to noise. the ds2431s 1-wire front-end differs from traditional slave devices in three characteristics. 1) there is additional lowpass filtering in the circuit that detects the falling edge at the beginning of a time slot. this reduces the sensitivity to high-frequency noise. this additional filtering does not apply at overdrive speed. 2) there is a hysteresis at the low-to-high switching threshold v th . if a negative glitch crosses v th but does not go below v th - v hy , it is not recognized (figure 12, case a). the hysteresis is effective at any 1-wire speed. 3) there is a time window specified by the rising edge hold-off time treh during which glitches are ignored, even if they extend below the v th - v hy threshold (figure 12, case b, t gl < t reh ). deep voltage drops or glitches that appear late after crossing the v th threshold and extend beyond the t reh window cannot be filtered out and are taken as the beginning of a new time slot (figure 12, case c, t gl t reh ). devices that have the parameters v hy and t reh speci - fied in their electrical characteristics use the improved 1-wire front-end. crc generation the ds2431 uses two different types of crcs. one crc is an 8-bit type and is stored in the most significant byte of the 64-bit rom. the bus master can compute a crc value from the first 56 bits of the 64-bit rom and compare it to the value stored within the ds2431 to determine if the rom data has been received error-free. the equivalent polynomial function of this crc is x 8 + x 5 + x 4 + 1. this 8-bit crc is received in the true (noninverted) form. it is computed at the factory and lasered into the rom. the other crc is a 16-bit type, generated according to the standardized crc-16 polynomial function x 16 + x 15 + x 2 + 1. this crc is used for fast verification of a data transfer when writing to or reading from the scratchpad. in contrast to the 8-bit crc, the 16-bit crc is always com - municated in the inverted form. a crc generator inside the ds2431 chip (figure 13) calculates a new 16-bit crc, as shown in the command flowchart (figure 7). the bus master compares the crc value read from the device to the one it calculates from the data and decides whether to continue with an operation or to reread the portion of the data with the crc error. with the write scratchpad command, the crc is gener - ated by first clearing the crc generator and then shifting in the command code, the target addresses ta1 and ta2, figure 12. noise suppression scheme v pup v th v hy 0v t reh t gl t reh t gl case a case c case b ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 19 downloaded from: http:///
and all the data bytes as they were sent by the bus mas - ter. the ds2431 transmits this crc only if e[2:0] = 111b. with the read scratchpad command, the crc is gener - ated by first clearing the crc generator and then shifting in the command code, the target addresses ta1 and ta2, the e/s byte, and the scratchpad data as they were sent by the ds2431. the ds2431 transmits this crc only if the reading continues through the end of the scratchpad. for more information on generating crc values, refer to application note 27. figure 13. crc-16 hardware description and polynomial symbol description rst 1-wire reset pulse generated by master. pd 1-wire presence pulse generated by slave. select command and data to satisfy the rom function protocol. ws command write scratchpad. rs command read scratchpad. cps command copy scratchpad. rm command read memory. ta target address ta1, ta2. ta-e/s target address ta1, ta2 with e/s byte. <8Ct[2:0] bytes> transfer of as many bytes as needed to reach the end of the scratchpad for a given target address. transfer of as many data bytes as are needed to reach the end of the memory. crc-16 transfer of an inverted crc-16 . ff loop indeinite loop where the master reads ff bytes. aa loop indeinite loop where the master reads aa bytes. programming data transfer to eeprom; no activity on the 1-wire bus permitted during this time. 1st stage 2nd stage 3rd stage 4th stage 7th stage 8th stage 6th stage 5th stage x 0 x 1 x 2 x 3 x 4 polynomial = x 16 + x 15 + x 2 + 1 input data crc output x 5 x 6 11th stage 12th stage 15th stage 14th stage 13th stage x 11 x 12 9th stage 10th stage x 9 x 10 x 13 x 14 x 7 16th stage x 16 x 15 x 8 ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 20 command-speciic 1-wire communication protocollegend downloaded from: http:///
master to slave slave to master programming write scratchpad (cannot fail) rst pd select ws ta <8Ct[2:0] bytes> crc-16 ff loop read scratchpad (cannot fail) rst pd select rs ta-e/s <8Ct[2:0] bytes> crc-16 ff loop copy scratchpad (success) rst pd select cps ta-e/s programming aa loop copy scratchpad (invalid address or pf = 1 or copy protected) rst pd select cps ta-e/s ff loop read memory (success) rst pd select rm ta ff loop read memory (invalid address) rst pd select rm ta ff loop ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 21 command-speciic 1-wire communication protocolcolor codes 1-wire communication examples downloaded from: http:///
memory function example write to the first 8 bytes of memory page 1. read the entire memory. with only a single ds2431 connected to the bus master, the communication looks like this: master mode data (lsb first) comments tx (reset) reset pulse rx (presence) presence pulse tx cch issue skip rom command tx 0fh issue write scratchpad command tx 20h ta1, beginning offset = 20h tx 00h ta2, address = 0020h tx <8 data bytes> write 8 bytes of data to scratchpad rx <2 bytes crc-16 > read crc to check for data integrity tx (reset) reset pulse rx (presence) presence pulse tx cch issue skip rom command tx aah issue read scratchpad command rx 20h read ta1, beginning offset = 20h rx 00h read ta2, address = 0020h rx 07h read e/s, ending offset = 111b, aa, pf = 0 rx <8 data bytes> read scratchpad data and verify rx <2 bytes crc-16 > read crc to check for data integrity tx (reset) reset pulse rx (presence) presence pulse tx cch issue skip rom command tx 55h issue copy scratchpad command tx 20h ta1 (authorization code) tx 00h ta2 tx 07h e/s <1-wire idle high> wait t progmax for the copy function to complete rx aah read copy status, aah = success tx (reset) reset pulse rx (presence) presence pulse tx cch issue skip rom command tx f0h issue read memory command tx 00h ta1, beginning offset = 00h tx 00h ta2, address = 0000h rx <144 data bytes> read the entire memory tx (reset) reset pulse rx (presence) presence pulse ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 22 downloaded from: http:///
2 3 1 2 3 1 3 2 1 n.c. io gnd to-92 top view n.c. io gnd n.c. n.c. n.c. tsoc + 54 6 23 1 ds2431 sfn (6mm x 6mm x 0.9mm) sfn (3.5mm x 6.5mm x 0.75mm) bottom view bottom view note: the sfn package is qualified for electro-mechanical contact applications only, not for soldering. for more information, refer to application note 4132: attachment methods for the electro-mechanical sfn package . 1 1 2 2 io io gnd gnd front view (t&r version) front view side view ds2431 ds2431g ds2431ga ucspr top view gnd n.c. n.c. a1 a2 a3 c1 c2 c3 io n.c. n.c. 1 6 n.c. n.c. 2 5 io n.c. 3 4 gnd n.c. tdfn (3mm x 3mm) top view ds2431 2431 ymrrf + *ep *exposed pad ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 23 pin conigurations downloaded from: http:///
user direction of feed leads face up in orientation shown above. sfn (6mm x 6mm x 0.9mm) user direction of feed leads face up in orientation shown above. sfn (3.5mm x 6.5mm x 0.75mm) ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 24 sfn package orientation on tape and reel downloaded from: http:///
package type package code outline no. land pattern no. 3 to-92 (bulk) q3+1 21-0248 3 to-92 (t&r) q3+4 21-0250 6 tsoc d6+1 21-0382 90-0321 2 sfn (6mm x 6mm) g266n+1 21-0390 2 sfn (3.5mm x 6.5mm) t23a6n+1 21-0575 6 tdfn-ep t633+2 21-0137 90-0058 6 ucspr br622+1 21-0376 refer to application note 1891 ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 25 package information for the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages . note that a +, #, or - in the package code indicates rohs status only. package drawings may show a different suffix character, but the drawing pertains to the package regardless of rohs status. downloaded from: http:///
revision number revision date description pages changed 0 050704 initial release 1 081604 replaced pin coniguration 1 in the electrical characteristics table, changed v tl(min) from 0.5v to 0.46v and v tl(max) from 4.1v to 4.4v; changed v hy(min) from 0.22v to 0.21v 2 in the copy scratchpad [55h] section, corrected the copy time from 13ms to 12.5ms 14 2 090506 added the sfn package and updated the ordering information table 1, 24 in the pin coniguration , added a note to the csp package outline *see package reliability report for important guidelines on qualiied usage conditions. 1 in the electrical characteristics table, changed the t prog (programming time) ec table parameter from 12.5ms to 10ms for version a2 (see also pages 1, 13). removed t fpd and updated t pdh , t msp , t w0l accordingly. changed i prog max to 0.8ma to match gbd 1, 2, 3, 13 updated memory function example table 23 3 122106 added csp package outline drawing number to pin coniguration 1 changed v tl(min) from 0.46v to 0.5v in the electrical characteristics table 2 in the absolute maximum ratings , changed storage temp to -55c to +125c; in the electrical characteristics table, changed v th , v tl based on v pup and data retention to 40 years min at 85c; added note to retention spec: eeprom writes can become nonfunctional after the data-retention time is exceeded. long-term storage at elevated temperatures is not recommended; the device can lose its write capability after 10 years at +125c or 40 years at +85c. 1, 2, 3 4 102207 in the ordering information table, removed all leaded part numbers and added the tdfn-ep package 1, 24 in the electrical characteristics table, changed the v il(max) spec from 0.3v to 0.5v; removed e from the t w1l(max) spec; added note 17 to t w0l spec; updated ec table notes 17 and 18; corrected note 20 2, 3 added ep function to the pin description table 3 added e to figure 11 write-zero time slot 19 in the pin coniguration , added the package drawing information/weblink and a note that the sfn package is qualiied for electro-mechanical contact applications only, not for soldering. added the sfn package orientation on tape-and-reel section. in the ordering information , added note to contact factory for availability of the ucspr package. added note that to-92 t&r leads are formed to approximately 100-mil spacing 24 5 032008 in the sfn pin coniguration , added reference to application note 4132 24 added package information table 25 6 8/08 created newer template-style data sheet all 7 6/09 deleted contact factory note in ordering information ; updated pin description and pin conigurations to relect changes in pin assignment of ucspr package 1, 5, 23 8 10/09 corrected part number in ordering information table 1 9 12/10 deleted the automotive version reference in the features section 1 10 3/11 added the automotive version reference to the features section 1 ds2431 1024-bit, 1-wire eeprom www.maximintegrated.com maxim integrated 26 revision history downloaded from: http:///
revision number revision date description pages changed 11 1/12 updated note 1 in the electrical characteristics section; speciied the data memory default status and added a note that the memory must be programmed to ffh for the eprom mode to function to the memory access section 3, 7, 8 12 2/12 added the 3.5mm x 6.5mm sfn package information to the ordering information table, pin conigurations, and package information table 1, 23, 24, 25 13 3/12 revised the electrical characteristics table notes 4 and 15 3 14 11/14 removed automotive references from features section 1 15 3/15 revised beneits and features section 1 maxim integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a maxim integrated product. no circuit patent licenses are implied. maxim integrated reserves the right to change the circuitry and speciications without n otice at any time. the parametric values (min and max limits) shown in the electrical characteristics table are guaranteed. other parametric values quoted in this data sheet are provided for guidance. maxim integrated and the maxim integrated logo are trademarks of maxim integrated products, inc. ds2431 1024-bit, 1-wire eeprom ? 2015 maxim integrated products, inc. 27 revision history (continued) for pricing, delivery, and ordering information, please contact maxim direct at 1-888-629-4642, or visit maxim integrateds website at www.maximintegrated.com. downloaded from: http:///

▲Up To Search▲

Price & Availability of DS2431-W0J1

	To Download DS2431-W0J1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .