View LA8522A_7880038.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LA8522A - 1 - rev01 m ar. 07 , 2013 www.inno.com.tw general description LA8522A is a voltage mode, step-down dc-dc converter that is designed to meet 2a output current, and utilizes pwm control scheme that switches with 300khz fixed frequency. the input voltage range of LA8522A is from 3.6v to 23v, and available in adjustable output voltage from 0.8v to v in . the supply current is only 3ma during operation and under 1ua in shutdown. this device provides an enable function that can be controlled by external logic signal. it also provides excellent regulation during line or load transient. other features of current limit, thermal shutdown protection, and short circuit protection are also included. due to the low r ds(on) of the internal power mosfet, this device provides high efficiency step-down applications. it can also operate with a maximum duty cycle of 100% for use in low drop-out conditions. the package is available in standard sop-8. features l l adjustable output voltage from 0.8v to v in l l 3.6v to 23v input voltage range l l continuous 2a output capability l l 300khz oscillation frequency l l 0.8v reference voltage l l 1ua low shutdown current l l 3ma low supply current l l 100% duty cycle l l built-in low r ds(on) power mosfet l l no external compensation required l l support low esr output ceramic capacitors l l adjustable current limit l l short circuit and thermal protection l l sop-8 package l l meet rohs standard applications l l broadband communication device l l lcd tv / monitor l l storage device l l wireless application ordering information LA8522A 1 2 3 4 1 (package type) => j : sop 2 (number of pins) => g : 8 pin 3 (output voltage) => blank : adjustable 4 (special feature) => blank : n/a available part number LA8522Ajg marking information LA8522Ajg 1 2 3 4 1 2 (date code) for date code rule, please contact our sales representative directly. 3 4 (internal code) 300khz, 2a/23v step-down dc-dc converter free datasheet http://www.0pdf.com
LA8522A - 2 - rev01 m ar. 07 , 2013 www.inno.com.tw 50% 60% 70% 80% 90% 100% 0 0.4 0.8 1.2 1.6 2 output current (a) efficiency (%) vout=2.5v vout=3.3v vout=5v vout=9v 50% 60% 70% 80% 90% 100% 0 0.4 0.8 1.2 1.6 2 output current (a) efficiency (%) vout=1.8v vout=2.5v vout=3.3v typical application l l 12v to 5v/2a with 10uf low esr ceramic capacitors v out =5v/2a v in =12v 10uf x 2 6.3v mlcc in sw gnd en 6.8k 1.3k fb 33uh 10uf x 2 16v mlcc LA8522A ocset 3k 1 5,6 7,8 3 2 4 2a sbd 470pf l l 5v to 1.8v/2a with 330uf electrolytic capacitors v out =1.8v/2a v in =5v in sw gnd en 2.5k 2k fb 12uh 330uf 6.3v e/c LA8522A ocset 4.7k 1 5,6 7,8 3 2 4 2a sbd 330uf 6.3v e/c l l efficiency curve v in =12v v in = 5 v free datasheet http://www.0pdf.com
LA8522A - 3 - rev01 m ar. 07 , 2013 www.inno.com.tw v in v out 5v 9v 12v 18v 1.2v l1 : 10uh r1 : 1.5kohm r2 : 3kohm r3 : 4.7kohm l1 : 12uh r1 : 1.5kohm r2 : 3kohm r3 : 3.3kohm 1.5v l1 : 12uh r1 : 1.3kohm r2 : 1.5kohm r3 : 4.7kohm l1 : 15uh r1 : 1.3kohm r2 : 1.5kohm r3 : 3.3kohm l1 : 18uh r1 : 1.3kohm r2 : 1.5kohm r3 : 3kohm 1.8v l1 : 12uh r1 : 2.5kohm r2 : 2kohm r3 : 4.7kohm l1 : 15uh r1 : 2.5kohm r2 : 2kohm r3 : 3.3kohm l1 : 22uh r1 : 2.5kohm r2 : 2kohm r3 : 3kohm 2.5v l1 : 15uh r1 : 4.7kohm r2 : 2.2kohm r3 : 4.7kohm l1 : 22uh r1 : 4.7kohm r2 : 2.2kohm r3 : 3.3kohm l1 : 22uh r1 : 4.7kohm r2 : 2.2kohm r3 : 3kohm l1 : 27uh r1 : 4.7kohm r2 : 2.2kohm r3 : 3kohm 3.3v l1 : 12uh r1 : 4.7kohm r2 : 1.5kohm r3 : 4.7kohm l1 : 22uh r1 : 4.7kohm r2 : 1.5kohm r3 : 3.3kohm l1 : 27uh r1 : 4.7kohm r2 : 1.5kohm r3 : 3kohm l1 : 33uh r1 : 4.7kohm r2 : 1.5kohm r3 : 3kohm 5v l1 : 27uh r1 : 6.8kohm r2 : 1.3kohm r3 : 3.3kohm l1 : 33uh r1 : 6.8kohm r2 : 1.3kohm r3 : 3kohm l1 : 39uh r1 : 6.8kohm r2 : 1.3kohm r3 : 3kohm 9v l1 : 27uh r1 : 10.2kohm r2 : 1kohm r3 : 3kohm l1 : 47uh r1 : 10.2kohm r2 : 1kohm r3 : 3kohm 12v l1 : 47uh r1 : 18.2kohm r2 : 1.3kohm r3 : 3kohm quick design table (1) for e/c application, i load = 2a, i l = 0.4a, continuous current mode operation. l1 : recommended inductor r1 : output voltage divider r2 : output voltage divider r3 : current limit setting resistor v out v in in sw gnd en r1 r2 fb l1 330uf e/c LA8522A ocset r3 1 5,6 7,8 3 2 4 2a sbd 330uf e/c free datasheet http://www.0pdf.com
LA8522A - 4 - rev01 m ar. 07 , 2013 www.inno.com.tw v in v out 5v 9v 12v 18v 2.5v l1 : 15uh c1 : 470pf r1 : 4.7kohm r2 : 2.2kohm r3 : 4.7kohm l1 : 27uh c1 : 470pf r1 : 4.7kohm r2 : 2.2kohm r3 : 3.3kohm 3.3v l1 : 12uh c1 : 470pf r1 : 4.7kohm r2 : 1.5kohm r3 : 4.7kohm l1 : 22uh c1 : 470pf r1 : 4.7kohm r2 : 1.5kohm r3 : 3.3kohm 5v l1 : 27uh c1 : 470pf r1 : 6.8kohm r2 : 1.3kohm r3 : 3.3kohm l1 : 33uh c1 : 470pf r1 : 6.8kohm r2 : 1.3kohm r3 : 3kohm 9v l1 : 27uh c1 : 470pf r1 : 10.2kohm r2 : 1kohm r3 : 3kohm l1 : 47uh c1 : 470pf r1 : 10.2kohm r2 : 1kohm r3 : 3kohm 12v l1 : 47uh c1 : 470pf r1 : 18.2kohm r2 : 1.3kohm r3 : 3kohm quick design table (2) for low esr mlcc application, i load = 2a, i l = 0.4a, continuous current mode operation. l1 : recommended inductor c1 : feed-forward capacitor r1 : output voltage divider r2 : output voltage divider r3 : current limit setting resistor v out v in 10uf x 2 mlcc in sw gnd en r1 r2 fb l1 10uf x 2 mlcc LA8522A ocset r3 1 5,6 7,8 3 2 4 2a sbd c1 free datasheet http://www.0pdf.com
LA8522A - 5 - rev01 m ar. 07 , 2013 www.inno.com.tw functional block diagram 0.8v reference voltage pwm-switched control circuit + - v on/off 90ua thermal shutdown 300khz osc sw in en ocset gnd fb pin configurations en sop-8 fb ocset in sw sw gnd gnd pin no. name description 1 fb this pin senses the feedback voltage to regulate the output voltage. connect this pin to a voltage divider to set the output voltage. 2 en this pin allows an external control signal to turn-on/off this device. float this pin or force it below 0.8v to turn-off this device, force it above 2v to turn-on this device. if this feature is not needed, connect this pin to in directly. 3 ocset add an external resistor from this pin to in to set current limit. 4 in the input pin of the step-down converter. a suitably large capacitor must be connected from this pin to ground to bypass noise on the input of the ic. 5,6 sw the output pin of the step-down converter. this pin is the switching node that supplies power to the output. connect a lc filter from this pin to the output load and a rectifier diode to the ground. 7,8 gnd the ground pin of the step-down converter. connect this pin to the circuit ground. free datasheet http://www.0pdf.com
LA8522A - 6 - rev01 m ar. 07 , 2013 www.inno.com.tw absolute maximum ratings parameter rating input voltage 25v sw pin voltage range -0.5v ~ v in +0.5v fb pin voltage range -0.3v ~ v in en pin voltage range -0.3v ~ v in +0.3v storage temperature range -65 c ~ 150 c junction temperature 150 c lead soldering temperature (10 sec) 300 c these are stress ratings only and functional operation is not implied. exposure to absolute maximum ratings for prolonged time periods may affect device reliability. all voltages are with respect to ground. recommended operating conditions parameter rating input voltage range 3.6v ~ 23v ambient temperature range -40 o c ~ 85 o c junction temperature range -40 o c ~ 125 o c these are conditions under which the device functions but the specifications might not be guaranteed. for guaranteed specifications and test conditions, please see the electrical specifications . package information parameter package symbol rating thermal resistance (junction to case) sop-8 jc 20 o c/w thermal resistance (junction to ambient) ja 60 o c/w free datasheet http://www.0pdf.com
LA8522A - 7 - rev01 m ar. 07 , 2013 www.inno.com.tw parameter symbol test condition min. typ. max. units feedback voltage v fb i load =0.1a 0.784 0.8 0.816 v efficiency v in =12v, v out =5v, i load =2a 92 % v in =5v, v out =3.3v, i load =2a 89 oscillation frequency f osc 240 300 360 khz frequency of short circuit protection f scp 30 50 70 khz duty cycle dc v fb =0v 100 % v fb =1.5v 0 internal mosfet on resistance r ds(on) v in =5v, v fb =0v 150 m v in =12v, v fb =0v 100 supply current i s v fb =1.5v 3 10 ma shutdown current i sd v en =0v 1 10 ua en pin input threshold voltage v en regulator off 1.3 0.8 v regulator on 2.0 en pin bias current i en regulator off 1 ua regulator on 20 fb pin bias current i fb i load =0.1a 0.1 0.5 ua ocset pin bias current i ocset i load =0.1a 75 90 105 ua line regulation v line v in =3.6v~23v, i load =0.1a 2 % load regulation v load i load =0.1a~2a 0.1 % over temperature shutdown t sd 150 o c over temperature shutdown hysteresis t hys 25 o c electrical specifications v in =12v, v out set to 3.3v, t a =25 o c, unless otherwise noted. free datasheet http://www.0pdf.com
LA8522A - 8 - rev01 m ar. 07 , 2013 www.inno.com.tw application information output voltage programming LA8522A develops a band-gap between the feedback pin and ground pin. therefore, the output voltage can be formed by r1 and r2. use 1% metal film resistors for the lowest temperature coefficient and the best stability. select lower resistor value to minimize noise pickup in the sensitive feedback pin, or higher resistor value to improve efficiency. the output voltage is given by the following formula: v out = v fb x ( 1 + r1 / r2 ) where v fb = 0.8v v out sw gnd r1 r2 fb v fb short circuit protection when the output is shorted to ground, the protection circuit will be triggered and force the oscillation frequency down to approximately 50khz. the oscillation frequency will return to 300khz once the output voltage or the feedback voltage rises above 0v. current limit setting this device reserves ocset pin to set the switching peak current. in general, the peak current must be 1.5 times of the continuous output current. it can be calculated as below: r ocset v in in ocset gnd i cl = (i ocset x r ocset ) / r ds(on) where i cl is the current limit, i ocset is the ocset bias current (90ua typ.), and r ds(on) is the on-resistance of the internal power mosfet. delay start-up the following circuit uses the en pin to provide a time delay between the input voltage is applied and the output voltage comes up. as the instant of the input voltage rises, the charging of capacitor c delay pulls the en pin low, keeping the device off. once the capacitor voltage rises above free datasheet http://www.0pdf.com
LA8522A - 9 - rev01 m ar. 07 , 2013 www.inno.com.tw the en pin threshold voltage, the device will start to operate. the start-up delay time can be calculated by the following formula: r delay c delay v en v in in en gnd v in x (1 C e -t/(rxc) ) > v en where t is the start-up delay time, r is r delay , c is c delay , and the typical v en is 1.3v. this feature is useful in situations where the input power source is limited in the amount of current it can deliver. it allows the input voltage to rise to a higher voltage before the device starts operating. snubber circuit the simple rc snubber is used for voltage transient and ringing suppression. the high frequency ringing and voltage overshooting at the sw pin is caused by fast switching transition and resonating circuit parasitical elements in the power circuit. it maybe generates emi and interferes with circuit performance. reserve a snubber circuit in the pc board is preferred to damp the ringing due to the parasitical capacitors and inductors of layout. the following circuit is a simple rc snubber: v out sw gnd c snub r snub fb choose the value of rc network by the following procedure: (1) measure the voltage ringing frequency (f r ) of the sw pin. (2) find a small capacitor and place it across the sw pin and the gnd pin to damp the ringing frequency by half. (3) the parasitical capacitance (c par ) at the sw pin is 1/3 the value of the added capacitance above. the parasitical inductance (l par ) at the sw pin is: par 2 r par c ) f 2 ( 1 = l (4) select the value of c snub that should be more than 2~4 times the value of c par but must be small enough so that the power dissipation of r snub is kept to a minimum. free datasheet http://www.0pdf.com
LA8522A - 10 - rev01 m ar. 07 , 2013 www.inno.com.tw the power rating of r snub can be calculated by following formula: s 2 in snub rsnub f v c = p_ (5) calculate the value of r snub by the following formula and adjust the value to meet the expectative peak voltage. par r snub l f 2 = r thermal considerations thermal protection limits total power dissipation in this device. when the junction temperature reaches approximately 150 c, the thermal sensor signals the shutdown logic turning off this device. the thermal sensor will turn this device on again after the ic's junction temperature cools by approximately 25 c. for continuous operation, do not exceed the maximum operation junction temperature 125 c. the power dissipation across this device can be calculated by the following formula: s in s gs s f r out in in out ) on ( ds load d i v + f v qg + f ) t + t ( i v 2 1 + v v x r i = p 2 where fs is the 300khz switching frequency, (tr+tf) is the switching time that is approximately 25ns, qg is the power mosfet gate charge that is approximately 6nc, v gs is the gate voltage of the power mosfet that is approximately equal v in , and i s is the 3ma supply current. the maximum power dissipation of this device depends on the thermal resistance of the ic package and pcb layout, the temperature difference between the die junction and ambient air, and the rate of airflow. the maximum power dissipation can be calculated by the following formula: ja a j d(max) ) -t (t = p where t j -t a is the temperature difference between the die junction and surrounding environment, ja is the thermal resistance from the junction to the surrounding environment. the value of junction to case thermal resistance jc is also popular to users. this thermal parameter is convenient for users to estimate the internal junction operated temperature of packages while ic operating. the operated junction temperature can be calculated by the following formula: jc d + c j p t = t t c is the package case temperature measured by thermal sensor. therefore it's easy to estimate the junction temperature by any condition. free datasheet http://www.0pdf.com
LA8522A - 11 - rev01 m ar. 07 , 2013 www.inno.com.tw there are many factors affect the thermal resistance. some of these factors include trace width, copper thickness, total pcb copper area, and etc. for the best thermal performance, wide copper traces and generous amounts of pcb copper should be used in the board layout. if further improve thermal characteristics are needed, double sided and multi-layer pcb with large copper areas and airflow will be recommended. layout considerations pc board layout is very important, especially for switching regulators of high frequencies and large peak currents. a good layout minimizes emi on the feedback path and provides best efficiency. the following layout guides should be used to ensure proper operation of this device. (1) the power charge path that consists of the in trace, the sw trace, the external inductor and the gnd trace should be kept wide and as short as possible. (2) the power discharge path that consists of the sw trace, the external inductor, the rectifier diode and the gnd trace should be kept wide and as short as possible. (3) the feedback path of voltage divider should be close to the fb pin and keep noisy traces away; also keep them separate using grounded copper. (4) the input capacitors should be close to the regulator and rectifier diode. (5) the output capacitors should be close to the load. free datasheet http://www.0pdf.com
LA8522A - 12 - rev01 m ar. 07 , 2013 www.inno.com.tw component selection inductor selection the conduction mode of power stage depends on input voltage, output voltage, output current, and the value of the inductor. select an inductor to maintain this device operating in continuous conduction mode (ccm). the minimum value of inductor can be determined by the following procedure. (1) calculate the minimum duty ratio: s on f ) on ( ds load ) max ( in f load out ) min ( t t = v + r i - v v + dcr i + v = d where dcr is the dc resistance of the inductor, v f is the forward voltage of the rectifier diode, and ts is the switching period. this formula can be simplified as below: 1 d 0 ; t t = v v = d s on ) max ( in out ) min ( (2) define a value of minimum current that is approximately 10%~30% of full load current to maintain continuous conduction mode, usually referred to as the critical current (i crit ). i crit i l i load t load crit i = i ; =0.1~0.3 (3) calculate the inductor ripple current ( i l ). in steady state conditions, the inductor ripple current increase, ( i l +), during the on time and the current decrease, ( i l -), during the off time must be equal. i crit i l t s t on t off t i l crit l i 2 = i (4) calculate the minimum value of inductor use maximum input voltage. that is the worst case condition because it gives the maximum i l . fs i d ] v - ) dcr + r ( i - v [ l l ) min ( out ) on ( ds load ) max ( in this formula can be simplified to fs i d ) v - v ( l l ) min ( out ) max ( in free datasheet http://www.0pdf.com
LA8522A - 13 - rev01 m ar. 07 , 2013 www.inno.com.tw the higher inductance results in lower output ripple current and ripple voltage. but it requires larger physical size and price. (5) calculate the inductor peak current and choose a suitable inductor to prevent saturation. 2 i + i = i l load ) peak ( l coil inductors and surface mount inductors are all available. the surface mount inductors can reduce the board size but they are more expensive and its larger dc resistance results in more conduction loss. the power dissipation is due to the dc resistance can be calculated as below: dcr i = p 2 load inductor _ d rectifier diode selection the rectifier diode provides a current path for the inductor current when the internal power mosfet turns off. the best solution is schottky diode, and some parameters about the diode must be take care as below: (1) the forward current rating must be higher than the continuous output current. (2) the reverse voltage rating must be higher than the maximum input voltage. (3) the lower forward voltage will reduce the conduction loss. (4) the faster reverse recovery time will reduce the switching loss, but it is very small compared to conduction loss. (5) the power dissipation can be calculated by the forward voltage and output current for the time that the diode is conducting. ) d - 1 ( v i = p f load diode _ d output capacitor selection the functions of the output capacitor are to store energy and maintain the output voltage. the low esr (equivalent series resistance) capacitors are preferred to reduce the output ripple voltage ( v out ) and conduction loss. the output ripple voltage can be calculated as below: ) c fs 8 1 + _ esr ( i = v out cout l out choose suitable capacitors must define the expectative value of output ripple voltage first. the esr of the aluminum electrolytic or the tantalum capacitor is an important parameter to determine the output ripple voltage. but the manufacturers usually do not specify esr in the specifications. assuming the capacitance is enough results in the output ripple voltage that due to free datasheet http://www.0pdf.com
LA8522A - 14 - rev01 m ar. 07 , 2013 www.inno.com.tw the capacitance can be ignored, the esr should be limited to achieve the expectative output ripple voltage. the maximum esr can be calculated as below: l out cout i v _ esr choose the output capacitance by the average value of the rc product as below: cout 6 - out _ esr 10 80 ~ 50 c if low esr ceramic capacitor is used as output capacitor, the output ripple voltage due to the esr can be ignored results in most of the output ripple voltage is due to the capacitance. therefore, the minimum output capacitance can be calculated as below: out l ) min ( out v fs 8 i c the prerequisites for using low esr output ceramic capacitors are duty cycle > 0.275 and feed-forward capacitor must be used to stabilize the control loop. the capacitors esr and ripple current result in power dissipation that will increase the internal temperature. usually, the capacitors manufacturers specify ripple current ratings and should not be exceeded to prevent excessive temperature shorten the life time. choose a smaller inductor causes higher ripple current which maybe result in the capacitor overstress. the rms ripple current flowing through the output capacitor and power dissipation can be calculated as below: 289 . 0 i = 12 i = _ i l l cout rms cout cout rms cout _ d _ esr ) _ i ( = p 2 the capacitor s esl (equivalent series inductance) maybe causes ringing in the low mhz region. choose low esl capacitors, limiting lead length of pcb and capacitor, and parallel connecting several smaller capacitors to replace with a larger one will reduce the ringing phenomenon. input capacitor selection the input capacitor is required to supply current to the regulator and maintain the dc input voltage. low esr capacitors are preferred those provide the better performance and the less ripple voltage. the input capacitors need an adequate rms current rating. it can be calculated by following formula and should not be exceeded. ) d - 1 ( d i = _ i ) max ( load cin rms free datasheet http://www.0pdf.com
LA8522A - 15 - rev01 m ar. 07 , 2013 www.inno.com.tw this formula has a maximum at v in =2v out . that is the worst case and the above formula can be simplified to: 2 i = _ i ) max ( load cin rms therefore, choose a suitable capacitor at input whose ripple current rating must greater than half of the maximum load current. the input ripple voltage ( v in ) mainly depends on the input capacitor s esr and its capacitance. assuming the input current of the regulator is constant, the required input capacitance for a given input ripple voltage can be calculated as below: ) _ esr i - v ( fs ) d - 1 ( d i = c cin ) max ( load in ) max ( load in if using aluminum electrolytic or tantalum input capacitors, parallel connecting 0.1uf bypass capacitor as close to the regulator as possible. if using ceramic capacitor, make sure the capacitance is enough to prevent the excessive input ripple current. the power dissipation of input capacitor causes a small conduction loss can be calculated as below: cin cin rms cin _ d _ esr ) _ i ( = p 2 free datasheet http://www.0pdf.com
LA8522A - 16 - rev01 m ar. 07 , 2013 www.inno.com.tw evaluation board layout evaluation board schematic key components supplier item manufacturer website manufacturer website inductor (l) chilisin www.chilisin.com.tw we www.we-online.com schottky diode (d) formosa www.formosams.com tip-tek www.tip-tek.com.tw electrolytic capacitor (c) ncc www.chemi-con.co.jp jamicon www.jamicon.com.tw smd capacitor (c) yageo www.yageo.com taiyo yuden www.yuden.co.jp smd resistor (r) yageo www.yageo.com free datasheet http://www.0pdf.com
LA8522A - 17 - rev01 m ar. 07 , 2013 www.inno.com.tw package outline sop-8 a h g b c k e f m l d j 0 . 2 5 min. max. a 5.80 6.20 b 4.80 5.00 c 3.80 4.00 d 0 8 e 0.40 0.90 f 0.19 0.25 m 0.10 0.25 h 0.35 0.49 l 1.35 1.75 j k g ref. dimensions millimeter 1.27 typ. 45 0.375 ref. free datasheet http://www.0pdf.com
LA8522A - 18 - rev01 m ar. 07 , 2013 www.inno.com.tw notice the specifications and product information of inno-tech co., ltd. are subject to change without any prior notice, and customer should contact inno-tech co., ltd. to obtain the latest relevant information before placing orders and verify that such information is current and complete. the information provided here is believed to be reliable and accurate; however inno-tech co., ltd. makes no guarantee for any errors that appear in this document. life support policy inno-tech products are not designed or authorized for use as critical components in life support devices or systems without the express written approval of the president of inno-tech co., ltd. as used herein: 1. life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. a critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. free datasheet http://www.0pdf.com

▲Up To Search▲

Price & Availability of LA8522A

	To Download LA8522A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .