1 d a t a s h e e t : c 4 d 1 5 1 2 0 a r e v . a C4D15120A Csilicon carbide schottky diode z -r ec ? r ectifier v rrm = 1200 v i f t c <135?c = 20 a q c = 96 nc features ? 1.2kv schottky rectifer ? zero reverse recovery current ? high-frequency operation ? temperature-independent switching ? extremely fast swtitching benefts ? replace bipolar with unipolar rectifers ? essentially no switching losses ? higher effciency ? reduction of heat sink requirements ? parallel devices without thermal runaway applications ? switch mode power supplies ? power factor correction ? motor drives package to-220-2 maximum ratings (t c =25c unless otherwise specifed) symbol parameter value unit test conditions note v rrm repetitive peak reverse voltage 1200 v v rsm surge peak reverse voltage 1300 v v r dc peak reverse voltage 1200 v i f continuous forward current 15 20 a t c <150?c, no ac component t c <135?c, no ac component i frm repetitive peak forward surge current 68 44 a t c =25?c, t p =10 ms, half sine pulse t c =110?c, t p =10 ms, half sine pulse i fsm non-repetitive forward surge current 100 85 a t c =25?c, t p =10 ms, half sine pulse t c =110?c, t p =10 ms, half sine pulse p tot power dissipation 192 83 w t c =25?c t c =110?c t c maximum case temperature 135 ?c t j operating junction range -55 to +175 ?c t stg storage temperature range -55 to +135 ?c to-220 mounting torque 1 8.8 nm lbf-in m3 screw 6-32 screw part number package marking C4D15120A to-220-2 c4d15120 pin 1 pin 2 case subject to change without notice. www.cree.com/power
2 0 5 10 15 20 25 30 0 0.5 1 1.5 2 2.5 3 3.5 4 electrical characteristics symbol parameter typ. max. unit test conditions note v f forward voltage 1.6 2.3 1.8 3 v i f = 15 a t j =25c i f = 15 a t j =175c i r reverse current 35 120 200 300 a v r = 1200 v t j =25c v r = 1200 v t j =175c q c total capacitive charge 96 nc v r = 1200 v, i f = 15a d i /d t = 200 a/s t j = 25c c total capacitance 1200 70 50 pf v r = 0 v, t j = 25c, f = 1 mhz v r = 400 v, t j = 25?c, f = 1 mhz v r = 800 v, t j = 25?c, f = 1 mhz 1. note:this is a majority carrier diode, so there is no reverse recovery charge. thermal characteristics symbol parameter typ. max. unit test conditions note r jc thermal resistance from junction to case 0.78 c/w typical performance figure 1. forward characteristics figure 2. reverse characteristics 0 1 2 3 4 5 200 400 600 800 1000 1200 1400 1600 1800 t j =-55c t j = 25c t j = 75c t j =125c t j =175c t j =-55c t j = 25c t j = 75c t j =125c t j =175c i f (a) v f (v) v r (v) i r (a) C4D15120A rev. a
3 0 10 20 30 40 50 60 70 80 90 100 25 50 75 100 125 150 175 figure 3. current derating figure 4. power derating 0 20 40 60 80 100 120 140 160 180 200 25 50 75 100 125 150 175 figure 5. recovery charge vs. reverse voltage figure 6. capacitance vs. reverse voltage typical performance 10% duty 30% duty 50% duty 70% duty dc 0 10 20 30 40 50 60 70 80 90 0 200 400 600 800 1000 0 200 400 600 800 1000 1200 1400 0.1 1 10 100 1000 i f(peak) (a) t c ?c t c ?c p tot (w) c (pf) v r (v) qrr (nc) v r (v) C4D15120A rev. a
4 figure 7. transient thermal impedance 0.0001 0.001 0.01 0.1 1 1e - 6 10e - 6 100e - 6 1e - 3 10e - 3 100e - 3 1 10 diode model v t r t diode model csd04060 vf t = v t + if*r t v t= 0.965 + (t j * - 1.3*10 - 3 ) r t= 0.096 + (t j * 1.0 6 *10 - 3 ) thermal resistance (?c/w) t (sec) t t t r if v vf * + = v t = 0.97 + ( t j * - 2.12*10 -3 ) r t = 0.031 + ( t j * 3.92*10 -4 ) note: t j is diode junction temperature in degrees celsius typical performance C4D15120A rev. a
5 5 recommended solder pad layout part number package marking C4D15120A to-220-2 c4d15120 to-220-2 a c e d g h b j l m n f p q s t u v w x y m i n m a x m i n m a x a . 3 9 5 . 4 1 0 1 0 . 0 3 3 1 0 . 4 1 4 b . 2 3 5 . 2 5 5 5 . 9 6 9 6 . 4 7 7 c . 1 0 2 . 1 1 2 2 . 5 9 1 2 . 8 4 5 d . 3 3 7 . 3 3 7 8 . 5 6 0 8 . 5 6 0 e . 5 9 0 . 6 1 0 1 4 . 9 8 6 1 5 . 4 9 4 f . 1 4 9 . 1 5 3 3 . 7 8 5 3 . 8 8 6 g 1 . 1 2 7 1 . 1 4 7 2 8 . 6 2 6 2 9 . 1 3 4 h . 5 3 0 . 5 5 0 1 3 . 4 6 2 1 3 . 9 7 0 j l . 0 2 8 . 0 3 6 . 7 1 1 . 9 1 4 m . 0 4 5 . 0 5 5 1 . 1 4 3 1 . 3 9 7 n . 1 9 5 . 2 0 5 4 . 9 5 3 5 . 2 0 7 p . 1 7 0 . 1 8 0 4 . 3 1 8 4 . 5 7 2 q . 0 4 8 . 0 5 4 1 . 2 1 9 1 . 3 7 1 s 3 5 3 5 t 3 5 3 5 u 3 5 3 5 v . 1 0 0 . 1 1 0 2 . 5 4 2 . 7 9 4 w . 0 1 4 . 0 2 1 . 3 5 6 . 5 3 3 x 3 5 3 5 y . 3 9 5 . 4 1 0 1 0 . 0 3 3 1 0 . 4 1 4 z . 1 3 0 . 1 5 0 3 . 3 0 2 3 . 8 1 0 i n c h e s m i l l i m e t e r s p o s r 0 . 0 1 0 r 0 . 2 5 4 1 2 z package dimensions package to-220-2 pos inches millimeters min max min max a .381 .410 9.677 10.414 b .235 .255 5.969 6.477 c .100 .120 2.540 3.048 d .223 .337 5.664 8.560 e .590 .615 14.986 15.621 f .143 .153 3.632 3.886 g 1.105 1.147 28.067 29.134 h .500 .550 12.700 13.970 j r 0.197 r 0.197 l .025 .036 .635 .914 m .045 .055 1.143 1.397 n .195 .205 4.953 5.207 p .165 .185 4.191 4.699 q .048 .054 1.219 1.372 s 3 6 3 6 t 3 6 3 6 u 3 6 3 6 v .094 .110 2.388 2.794 w .014 .025 .356 .635 x 3 5.5 3 5.5 y .385 .410 9.779 10.414 z .130 .150 3.302 3.810 note: 1. dimension l, m, w apply for solder dip finish pin 1 pin 2 case C4D15120A rev. a this product has not been designed or tested for use in, and is not intended for use in, applications implanted into the human body nor in applications in which failure of the product could lead to death, personal injury or property damage, including but not limited to equipment used in the operation of nuclear facilities, life-support machines, cardiac defbrillators or similar emergency medical equipment, aircraft navigation or communication or control systems, air traffc control systems, or weapons systems. copyright ? 2006-2011 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree, the cree logo, and zero recovery are registered trademarks of cree, inc. cree, inc. 4600 silicon drive durham, nc 27703 usa tel: +1.919.313.5300 fax: +1.919.313.5451 www.cree.com/power
|
