http://www.tracopower.com page 1 of 4 dc/dc converters thl 10wi series, 10 watt features 10 watt in 1 x 1 package shielded metal case with isolated baseplate ultrawide 4:1 input voltage ranges remote on/off control operating temp. range C40c to +75c and up to +85c with heat-sink i/o isolation voltage 1500 vdc input flter meets en 55022 class a without external components cost optimized design industry standard pinout 3-year product warranty the thl 10wi is a series of general purpose 10 watt dc/dc-converters packed in the compact 1 x 1 case and is a pin to pin replacement for the popular 1 x 2 size products. the industrial standard pinout, the ultra wide 4:1 input voltage range and the input flter that meets en 55022 class a without external components make these converters easy to design in and suitable for to cost optimize many existing and new applications. the models have a remote on/off control, short circuit and overvoltage protection and are applicable in temperature ranges of up to +75c or +85c with optional mounted heat sink. typical applications are instrumentation, distributed power ar - chitectures in communication and industrial electronics. order code input voltage range output voltage output current max. effciency typ. thl 10-2410wi 3.3 vdc 2200 ma 86 % thl 10-2411wi 5.1 vdc 2000 ma 84 % thl 10-2412wi 12 vdc 830 ma 86 % thl 10-2413wi 9 C 36 vdc 15 vdc 660 ma 87 % thl 10-2415wi (24 vdc nominal) 24 vdc 410 ma 86 % thl 10-2421wi 5.0 vdc 1000 ma 84 % thl 10-2422wi 12 vdc 410 ma 86 % thl 10-2423wi 15 vdc 330 ma 87 % thl 10-4810wi 3.3 vdc 2200 ma 85 % thl 10-4811wi 5.1 vdc 2000 ma 84 % thl 10-4812wi 12 vdc 830 ma 86 % thl 10-4813wi 18 C 75 vdc 15 vdc 660 ma 87 % thl 10-4815wi (48 vdc nominal) 24 vdc 410 ma 86 % thl 10-4821wi 5.0 vdc 1000 ma 84 % thl 10-4822wi 12 vdc 410 ma 86 % thl 10-4823wi 15 vdc 330 ma 87 % models cb scheme ul 60 95 0- 1u l 60 95 0- 1 226037 pending
http://www.tracopower.com page 2 of 4 dc/dc converters thl 10wi series 10 watt input specifications input current at no load (at nominal input voltage) 24 v models : 30 ma typ. 48 v models : 20 ma typ. input current at full load (at nominal input voltage) 24 v; 3.3 vdc models : 400 ma typ. 24 v; other models: 500 ma typ.. 48 v; 3.3 vdc models : 200 ma typ. 48 v; other models : 250 ma typ. start-up voltage / under voltage lockout 24 v models: 9 vdc / 8.5 vdc (or lower) (hysteresis for assertive on) 48 v models: 18 vdc / 17 vdc (or lower) (long term operation at undervoltage will demage the converter!) surge voltage (1 sec. max.) 24 vin models: 50 v max. 48 vin models: 100 v max. conducted noise (input) en 55022 class a, fcc part 15, level a without external components recommended input fuse (slow blow) 24 v models: 2000 ma 48 v models: 1000 ma output specifications voltage set accuracy 2 % regulation C input variation (vmin C vmax) 1.0 % max. C load variation single output models: 1.2 % max. (15 C 100 % load) dual output models: 2.0 % max. (15 C 100 % balanced load) minimum load 15 % of rated max. current (operation at lower load condition will not damage the converters. however, they may not meet all listed specifications) ripple and noise (20 mhz bandwidth) 60 mvp-p typ. temperature coefficient 0.02 %/k output current limitation >110 % of iout max. short circuit protection indefinite, automatic recovery transient response setting time 300 s typ. (25 % load step change) maximum capacitive load 3.3 vdc models: 560 f 5 vdc models: 560 f 12 vdc models: 150 f 15 vdc models: 150 f 24 vdc models: 68 f 5.0 vdc models: 220 f (each output) 12 vdc models: 100 f (each output) 15 vdc models: 100 f (each output)
http://www.tracopower.com page 3 of 4 all specifcations valid at nominal input voltage, full load and +25c after warm-up time unless otherwise stated. dc/dc converters thl 10wi series 10 watt general specifications temperature ranges C operating without heat sink C40c to +75c (with derating) C operating with heat sink C40c to +85c (with derating) C case temperature +100c max. C storage C40c to +125c power derating C operating without heat sink 2.5 %/k above +60c C operating with heat sink 3.5 %/k above +70c thermal inpedance C natural convection 18.2c/w C natural convection with heat sink 15.8c/w humidi ty (non condensing) 95 % rel h max. reliability, calculated mtbf (mil-hdbk-217f, at +25c, ground benign) >350000 h isolation voltage (60 sec.) C input/output 1500 vdc isolation capacitance C input/output 1200 pf max. isolation resistance C input/output (500 vdc) >1000 mohm remote on/off C on: 2.5 ... 50 vdc or open circuit C off: 0 ... +1.0 vdc or short circuit pin 6 and pin 2 C off idle current: 10 ma max. switching frequency (fixed) 400 khz typ. (pulse width modulation pwm) altitude during operation 5000 m max. (164 0 0 f t ) approved safety standards ul/cul 60950-1, iec/en 60950-1 safety approvals C ul/cul www.ul.com -> file no. e188913 (entry pending) C cb test certificate according iec 60950-1 www.tracopower.com/products/thl10wi-cb.pdf C csa certificate for ul/cul 60950-1 www.tracopower.com/products/thl10wi-csa.pdf environmental compliance C reach www.tracopower.com/products/thl10wi-reach.pdf C rohs rohs directive 2002/95/ec physical specifications casing material metal baseplate non conductive fr4 potting material epoxy (ul 94v-0 rated) weight 15 g (0.53oz) soldering temperature max. +260c / 10sec. application note : www.tracopower.com/products/thl10wi-application.pdf
page 4 of 4 dc/dc converters thl 10wi series 10 watt outline dimensions dimensions in [mm], () = inch pin diameter ? 1.0 (0.04) pin pitch tolerances: 0.25 (0.01) tolerances: 0.5 (0.02) r e v. 0 6/12.1 specifcations can be changed any time without notice. pin single dual 1 +vin (vcc) +vin (vcc) 2 Cvin (gnd) Cvin (gnd) 3 + vout + vout 4 no pin common 5 Cvout Cvout 6 remote on/off pin-out note: the product label on converter has to be re - moved before mounting the heat-sink. for volume orders converters will be sup - plied with heat-sink already mounted. please contact factory for quotation. separate heat-sinks are only available for prototypes and small quantity orders. order code: thl-hs1 (cont.: heat-sink, thermal pad, 2 clamps) material: aluminum finish: anodic treatment (black) weight: 4.0 g (0.14oz) without converter thermal impedance after assembling: 15.8 k/w 31.0 (1.22) max. 16.3 (0.64) 17.5 (0.69) max. conver ter heat-sink thermal pad clamp 25.4 25.4 bottom view 20.32 7.62 6.0 (0.3) (0.24) (0.8) (1.0) (1.0) 5.08 (0.2) 10.2 (0.4) 1 2 3 6 5 2.5 (0.1) 4 10.16 (0.4) 2.5 (0.1) 10.16 (0.4) heat-sink (option) jenatschstrasse 1 ch-8002 zurich switzerland t el. +41 43 311 45 11 fax +41 43 311 45 45 info@traco.ch www .tracopower .com
|