do not scale from this print *-01: 1 position -02: 2 positions -04: 4 positions -06: 6 positions -08: 8 positions *-10: 10 positions lead style no. of positions per row -01: right angle ip5-xx-01-x-x-xxx-x-tr tail options plating options -l: 10" gold, matte tin on signal tails, shields, & weld tabs -ra1: .062" thick board *-ra2: .093" thick board (*=not tooled) -l: cable latch options row -s: single row packaging -tr: tape and reel (see note 3) = "e" "d" eq. spcs @ .1575 .0050 [4.001 0.127] .351 8.92 (ref) .010 (ref) 0.25 "f" = "e" "d" eq. spcs @ .1575 .0050 [4.001 0.127] "b" - .007 + .005 (either direction) 0 .5 sway "f" "a" "a" c c c c ip-ra-xx-01 c a "a" (ref) "c" (ref) pin 1 indicator sub-itp-ra-01.0-x-x (typ) .015 (ref) 0.38 .273 6.93 (ref) .580 (ref) 14.72 .493 (ref) 12.52 .045 1.15 (ref) .076 1.92 (ref) .025 (ref) (typ) 0.64 .188 4.76 .328 8.34 .383 9.72 c .008 0.20 .015 0.38 .0780 1.981 (ref) .0780 1.981 (ref) section "a"-"a" scale 8 : 1 c fig.1 (ip5-04-01-l-s-xxx-x shown) a sheet of unless otherwise specified, dimensions are in inches [millimeters] tolerances are: decimals angles .xx: .01 [.3] 2 .xxx: .005 [.13] .xxxx: .0030 [.076] material: by: ip5-xx-01-x-x-xxx-x-tr dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing knowlden 6/27/08 2 1 sheet scale: 4:1 c:\enterprisevault\dwg\misc\mktg\ip5-xx-01-x-x-xxx-x-tr-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 body: high temp nylon shield & weld tab: phos brz. terminal: copper alloy dielectric: lcp, color: black notes: 1. represents a critical dimension. 2. parts to be packaged in trays. 3. for quantities up to 49 pieces, no leader, trailer or reel will be supplied. for quantities of 50-124 pieces, no leader or trailer will be supplied. 4. itp5-ra and wt push out and retention force to be .5 lbs (2.2n) ip5-ra connector assembly revision a
"f" "h" "f" fig.2 (ip5-04-01-l-s-xxx-l shown) (same as fig. 1, except as shown) ip-ra-xx-01-l itp5-ra-01.0-x-x "g" ref .132 3.34 process step 1 (filling itp-ra sub assemblies into body) itp5-ra-01.0-x-x (typ) c .132 3.34 .020 min. 0.51 (after heat staking) (typ) process step 2 (heat staking itp-ra sub assemblies into body) c c "h" (-l option) "b" (std, no option) process step 3 (fill wt-45-xx-t weld tabs) wt-45-xx-t c "f" .188 4.76 c wt-45-xx-t a sheet of ip5-ra connector assembly by: ip5-xx-01-x-x-xxx-x-tr dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing knowlden 6/27/08 2 2 sheet scale: 4:1 revision a c:\enterprisevault\dwg\misc\mktg\ip5-xx-01-x-x-xxx-x-tr-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|