ds-147 rev c saronix saronix voltage controlled crystal oscillator technical data s1528 series 141 jefferson drive ? menlo park, ca 94025 usa 650-470-7700 800-227-8974 fax 650-462-9894 cmos / ttl frequency range: 1.5 mhz to 27 mhz frequency stability: actual size description a voltage controlled crystal oscillator providing precise rise and fall times to drive high performance applications. the device is packaged in a 6-pin, smd, j leaded package. the plastic molded sur- face mountable package is ideal for to- day's automated assembly environments. 50 ppm over all conditions: operating temperature, voltage change, load change, calibration tolerance, aging, with v c = 2.5v applications for use with phase-locked loop (pll) for clock and data recovery, frequency translation, or frequency synthesis ap- plications in video, telephony, and data communication environments. plastic molded, j-lead smd package ttl and cmos compatible tri-state output for frequencies above 27 mhz, see saronix s1518 series available as 3.3v version, see saronix s1328 series available on tape & reel; 24mm tape, 500pcs per reel output waveform t r t f t r t f ttl cmos v dd symmetry symmetry 80% v dd 50% v dd 20% v dd 0 level gnd 2.5 vdc 1.5 vdc 0.5 vdc temperature range: operating: storage: 0 to +70c, 0 to +85c, -40 to +85c -55 to +125c supply voltage: recommended operating: 5v 5% supply current: 20ma typ, 30ma max @ 25c, 40ma max @ operating temp range 1 level output: symmetry: rise & fall times: logic 0: logic 1: load: period jitter rms: see part numbering guide and output waveform 5ns max, 20% to 80% v dd, cmos 4ns max, 0.4v to 2.4 vdc, ttl 10% v dd max for cmos or 0.4 vdc max for ttl v cc -0.6 vdc for cmos or 2.4 vdc min for ttl 50pf or 10 ttl 8ps max * apr = (vcxo pull relative to specified output freq. @ nominal control voltage) ? (vcxo freq. stability) pull characteristics: input impedance: frequency response (-3db): pullability: control voltage: transfer function: linearity: center control voltage: 50k ? min 20khz 20, 50, 70, 100 ppm apr* (see part numbering guide) 0.5 to 4.5v frequency increases when control voltage increases 10% max 2.5v mechanical: shock: solderability: terminal strength: vibration: resistance to soldering heat: environmental: thermal shock: moisture resistance: mil-std-883, method 1011, condition a mil-std-883, method 1004 mil-std-883, method 2002, condition b mil-std-883, method 2003 mil-std-202, method 211, conditions a & c mil-std-883, method 2007, condition a mil-std-202, method 210, condition i or j
ds-147 rev c saronix s1528 series saronix voltage controlled crystal oscillator technical data 141 jefferson drive ? menlo park, ca 94025 usa 650-470-7700 800-227-8974 fax 650-462-9894 cmos / ttl all specifications are subject to change without notice. tri-state logic table required input levels on pin 2: logic 1 = 3.0v min logic 0 = 0.5v max pin 2 input logic 1 or nc pin 4 output oscillation high impedance or standby function logic 0 or gnd package details denotes pin 1 6 5 4 1 2 3 8.74 .344 max 10.4 .409 6.1 .240 5.9 .234 max 13.2 .520 max 0.46 .018 2.54 .100 5.08 .200 0.51 .020 x45 cham .75 .030 8.74 .344 1.50.15 .059.006 pin functions: pin 1: control voltage pin 2: tri-state control pin 3: gnd scale: none (dimensions in ) recommended land pattern mm inches 8.74 .344 2.54 .100 2.5 .100 5.08 .200 1.27 .050 pin 4: output pin 5: n/c pin 6: +5vdc (v cc ) solder reflow guide reflow 240c max preheat 183 10c cooling 250 4c/sec max temperature ? c 4c/sec max part numbering guide 10 sec max 1 ? 2 minutes time s1528 c g e a - 6.1760 (t) series s1528 = 5v vcxo, j lead smd logic type t = ttl c = cmos absolute pull range * c = g = h = m = 20 50 100 70 frequency (mhz) symmetry a = 45/55% max ** b = 40/60% max test circuits simulated test load 390 ? v cc ma m oscillator pin 5 pin 4 pin 6 pin 1 pin 2 pin 3 0.1 f vc c l = 15 pf (note a) power supply tri-state input or enable/disable (current limited on fixture) note a: c l includes probe and jig capacitance. ttl test circuit oscillator pin 5 pin 4 pin 6 pin 1 pin 2 pin 3 0.1 f vc ma m c l = 50 pf (note a) power supply tri-state input or enable/disable (current limited on fixture) note a: c l includes probe and jig capacitance. hcmos test circuit ppm ppm ppm *** ppm 150 200 operating temperature c = e = l = 0 to +70c 0 to +85c -40 to +85c * apr = (vcxo pull relative to specified output freq. @ nominal control voltage) ? (vcxo freq. stability) ** not available at all frequencies; ttl 13.5 to 27 mhz only *** not available at all frequencies and all operating temperature ranges, please contact saronix (t) = tape & reel full reel increments only
|
