ad558Cspecifications model ad558j ad558k ad558s 1 ad558t 1 min typ max min typ max min typ max min typ max units resolution 8 8 8 8 bits relative accuracy 2 0 c to +70 c 1/2 1/4 1/2 1/4 lsb C55 c to +125 c 3/4 3/8 lsb output ranges 3 0 to +2.56 0 to +2.56 0 to +2.56 0 to +2.56 v 0 to +10 0 to +10 0 to +10 0 to +10 v current source +5 +5 +5 +5 ma sink internal passive internal passive internal passive internal passive pull-down to ground 4 pull-down to ground pull-down to ground pull-down to ground output settling time 5 0 to 2.56 volt range 0.8 1.5 0.8 1.5 0.8 1.5 0.8 1.5 m s 0 to 10 volt range 4 2.0 3.0 2.0 3.0 2.0 3.0 2.0 3.0 m s full-scale accuracy 6 @ 25 c 6 1.5 6 0.5 6 1.5 6 0.5 lsb t min to t max 6 2.5 6 1 6 2.5 6 1 lsb zero error @ 25 c 6 1 6 1/2 6 1 6 1/2 lsb t min to t max 6 2 6 1 6 2 6 1 lsb monotonicity 7 t min to t max guaranteed guaranteed guaranteed guaranteed digital inputs t min to t max input current 100 100 100 100 m a data inputs, voltage bit on-logic 1 2.0 2.0 2.0 2.0 v bit on-logic 0 0 0.8 0 0 0 v control inputs, voltage on-logic 1 2.0 2.0 2.0 2.0 v on-logic 0 0 0.8 0 0.8 0 0.8 0 0.8 v input capacitance 4 4 4 4 pf timing 8 t w , strobe pulse width 200 200 200 200 ns t min to t max 270 270 270 270 ns t dh data hold time 10 10 10 10 ns t min to t max 10 10 10 10 ns t ds data set-up time 200 200 200 200 ns t min to t max 270 270 270 270 ns power supply operating voltage range (v cc ) 2.56 volt range +4.5 +16.5 +4.5 +16.5 +4.5 +16.5 +4.5 +16.5 v 10 volt range +11.4 +16.5 +11.4 +16.5 +11.4 +16.5 +11.4 +16.5 v current (i cc )1 5 25 15 25 15 25 15 25 ma rejection ratio 0.03 0.03 0.03 0.03 %/% power dissipation, v cc = 5 v 75 125 75 125 75 125 75 125 mw v cc = 15 v 225 375 225 375 225 375 225 375 mw operating temperature range 0 +70 0 +70 C55 +125 C55 +125 c notes 1 the ad558 s & t grades are available processed and screened lo mil-std-883 class b. consult analog devices military databook for details. 2 relative accuracy is defined as the deviation of the code transition points from the ideal transfer point on a straight line from the offset to the full scale of the device. see measuring offset error. 3 operation of the 0 volt to 10 volt output range requires a minimum supply voltage of +11.4 volts. 4 passive pull-down resistance is 2 k w for 2.56 volt range, 10 k w for 10 volt range. 5 settling time is specified for a positive-going full-scale step to 1/2 lsb. negative-going steps to zero are slower, but can be improved with an external pull-down. 6 the full range output voltage for the 2.56 range is 2.55 v and is guaranteed with a +5 v supply, for the 10 v range, it is 9.960 v guaranteed with a +15 v supply. 7 a monotonic converter has a maximum differential linearity error of 1 lsb. 8 see figure 7. specifications shown in boldface are tested on all production units at final electrical test. specifications subject to change without notice. (@ t a = +25 8 c, v cc = +5 v to +15 v unless otherwise noted) rev. a C2C
ad558 rev. a C3C absolute maximum ratings* v cc to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 v to +18 v digital inputs (pins 1C10) . . . . . . . . . . . . . . . . . . 0 v to +7.0 v v out . . . . . . . . . . . . . . . . . . . . . . . indefinite short to ground momentary short to v cc power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450 mw storage temperature range n/p (plastic) packages . . . . . . . . . . . . . . . . C25 c to +100 c d (ceramic) package . . . . . . . . . . . . . . . . . C55 c to +150 c lead temperature (soldering, 10 sec) . . . . . . . . . . . . . +300 c thermal resistance junction to ambient/junction to case d (ceramic) package . . . . . . . . . . . . . . 100 c/w/30 c/w n/p (plastic) packages . . . . . . . . . . . . . 140 c/w/55 c/w *stresses greater than those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. ad558 metalization photograph dimensions shown in inches and (mm). figure 1a. ad558 pin configuration (dip) 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 ad558 top view (not to scale) v out v out sense v out select gnd gnd +v cc cs (lsb) db0 db1 db2 db3 db4 db5 db6 (msb) db7 ce figure 1a. ad558 pin configuration (dip) ad558 top view (not to scale) 1 2 3 20 19 9 10 11 12 13 4 5 7 6 8 18 17 16 15 14 v out select gnd nc gnd +v cc db2 db3 db4 db5 nc db1 db0 (lsb) nc v out v out sense db6 (msb) db7 nc ce cs nc = no connect figure 1b. ad558 pin configuration (plcc and lcc) ordering guide relative accuracy full-scale error max error, max package model 1 temperature t min to t max t min to t max option 2 ad558jn 0 c to +70 c 1/2 lsb 2.5 lsb plastic (n-16) ad558jp 0 c to +70 c 1/2 lsb 2.5 lsb plcc (p-20a) ad558jd 0 c to +70 c 1/2 lsb 2.5 lsb to-116 (d-16) ad558kn 0 c to +70 c 1/4 lsb 1 lsb plastic (n-16) ad558kp 0 c to +70 c 1/4 lsb 1 lsb plcc (p-20a) ad558kd 0 c to +70 c 1/4 lsb 1 lsb to-116 (d-16) ad558sd C55 c to +125 c 3/4 lsb 2.5 lsb to-116 (d-16) ad558td C55 c to +125 c 3/8 lsb 1 lsb to-116 (d-16) notes 1 for details on grade and package offerings screened in accordance with mil-std-883, refer to the analog devices military products databook or current ad558/883b data sheet. 2 d = ceramic dip; n = plastic dip; p = plastic leaded chip carrier.
ad558 rev. a C4C circuit description the ad558 consists of four major functional blocks, fabricated on a single monolithic chip (see figure 2). the main d-to-a converter section uses eight equally-weighted laser-trimmed current sources switched into a silicon-chromium thin-film r/2r resistor ladder network to give a direct but unbuffered 0 mv to 400 mv output range. the transistors that form the dac switches are pnps; this allows direct positive-voltage logic interface and a zero-based output range. control amp band- gap reference output amp 8-bit voltage-switching d-to-a converter i 2 l latches i 2 l control logic v out v out v out sense select +v cc msb cs ce lsb control inputs db0 db1 db2 db3 db4 db5 db6 db7 digital input data gnd gnd figure 2. ad558 functional block diagram the high speed output buffer amplifier is operated in the non- inverting mode with gain determined by the user-connections at the output range select pin. the gain-setting application resistors are thin-film laser-trimmed to match and track the dac resistors and to assure precise initial calibration of the two output ranges, 0 v to 2.56 v and 0 v to 10 v. the amplifier output stage is an npn transistor with passive pull-down for zero-based output capability with a single power supply. the internal precision voltage reference is of the patented bandgap type. this design produces a reference voltage of 1.2 volts and thus, unlike 6.3 volt temperature compensated zeners, may be operated from a single, low voltage logic power supply. the microprocessor interface logic consists of an 8-bit data latch and control circuitry. low power, small geometry and high speed are advantages of the i 2 l design as applied to this section. i 2 l is bipolar process compatible so that the performance of the ana- log sections need not be compromised to provide on-chip logic capabilities. the control logic allows the latches to be operated from a decoded microprocessor address and write signal. if the application does not involve a m p or data bus, wiring cs and ce to ground renders the latches transparent for direct dac access. mil-std-883 the rigors of the military/aerospace environment, temperature extremes, humidity, mechanical stress, etc., demand the utmost in electronic circuits. the ad558, with the inherent reliability of integrated circuit construction, was designed with these ap- plic ations in mind. the hermetically-sealed, low profile dip package takes up a fraction of the space required by equivalent modular designs and protects the chip from hazardous environ- ments. to further ensure reliability, military temperature range ad558 grades s and t are avai lable sc reened to mil-s td-883. for more complete data sheet information consult the analog devices military databook. chip availability the ad558 is available in laser-trimmed, passivated chip form. ad558j and ad558t chips are available. consult the factory for details. input logic coding digital input code output voltage binary hexadecimal decimal 2.56 v range 10.000 v range 0000 0000 00 0 0 0 0000 0001 01 1 0.010 v 0.039 v 0000 0010 02 2 0.020 v 0.078 v 0000 1111 0f 15 0.150 v 0.586 v 0001 0000 10 16 0.160 v 0.625 v 0111 1111 7f 127 1.270 v 4.961 v 1000 0000 80 128 1.280 v 5.000 v 1100 0000 c0 192 1.920 v 7.500 v 1111 1111 ff 255 2.55 v 9.961 v connecting the ad558 the ad558 has been configured for ease of application. all ref- erence, output amplifier and logic connections are made inter- nally. in addition, all calibration trims are performed at the factory assuring specified accuracy without user trims. the only connection decision that must be made by the user is a single jumper to select output voltage range. clean circuit board lay- out is facilitated by isolating all digital bit inputs on one side of the package; analog outputs are on the opposite side. figure 3 shows the two alternative output range connections. the 0 v to 2.56 v range may be selected for use with any power supply between +4.5 v and +16.5 v. the 0 v to 10 v range requires a power supply of +11.4 v to +16.5 v. output amp 16 15 14 13 gnd v out select v out sense v out output amp 16 15 14 13 gnd v out select v out sense v out a. 0 v to 2.56 v output range b. 0 v to 10 v output range figure 3. connection diagrams because of its precise factory calibration, the ad558 is intended to be operated without user trims for gain and offset; therefore no provisions have been made for such user trims. if a s mall in- crease in scale is required, however, it may be accomplished by slightly altering the effective gain of the output buffer. a resistor in series with v out sense will increase the output range. for example if a 0 v to 10.24 v output range is desired (40 mv = 1 lsb), a nominal resistance of 850 w is required. it must be remembered that, although the internal resistors all ratio- match and track, the absolute tolerance of these resistors is typically 20% and the absolute tc is typically C50 ppm/ c (0 to C100 ppm/ c). that must be considered when rescaling is performed. figure 4 shows the recommended circuitry for a full-scale output range of 10.24 volts. internal resistance values shown are nominal.
applicationsCad558 rev. a C5C the only consideration in selecting a supply voltage is that, in order to be able to use the 0 v to 10 v output range, the power supply voltage must be between +11.4 v and +16.5 v. if, how- ever, the 0 v to 2.56 v range is to be used, power consumption will be minimized by utilizing the lowest available supply voltage (above +4.5 v). timing and control the ad558 has data input latches that simplify interface to 8- and 16-bit data buses. these latches are controlled by chip enable ( ce ) and chip select ( cs ) inputs. ce and cs are inter- nally nored so that the latches transmit input data to the dac section when both ce and cs are at logic 0. if the ap- plication does not involve a data bus, a 00 condition allows for direct operation of the dac. when either ce or cs go to logic 1, the input data is latched into the registers and held until both ce and cs return to 0. (unused ce or cs inputs should be tied to ground.) the truth table is given in table i. the logic function is also shown in figure 6. table i. ad558 control logic truth table latch input data ce cs dac data condition 0 0 0 0 transparent 1 0 0 1 transparent 0 g 0 0 latching 1 g 0 1 latching 00 g 0 latching 10 g 1 latching x 1 x previous data latched x x 1 previous data latched notes x = does not matter. g = logic threshold at positive-going transition. figure 6. ad558 control logic function in a level-triggered latch such as that in the ad558 there is an interaction between data setup and hold times and the width of the enable pulse. in an effort to reduce the time required to test all possible combinations in production, the ad558 is tested with t ds = t w = 200 ns at 25 c and 270 ns at t min and t max , with t dh = 10 ns at all temperatures. failure to comply with these specifications may result in data not being latched p roperly. figure 7 shows the timing for the data and control signals; ce and cs are identical in timing as well as in function. output amp 16 15 14 13 gnd v out 14kw 2kw 40kw 500w 604w figure 4. 10.24 v full-scale connection note: decreasing the scale by putting a resistor in series with gnd will not work properly due to the code-dependent currents in gnd. adjusting offset by injecting dc at gnd is not recommended for the same reason. grounding and bypassing* all precision converter products require careful application of good grounding practices to maintain full rated performance. because the ad558 is intended for application in microcom- puter systems where digital noise is prevalent, special care must be taken to assure that its inherent precision is realized. the ad558 has two ground (common) pins; this minimizes ground drops and noise in the analog signal path. figure 5 shows how the ground connections should be made. output amp 16 15 14 13 gnd v out select v out sense v out 12 11 (see next page) r l gnd to system gnd to system gnd (see text) to system v cc +v cc 0.1mf figure 5. recommended grounding and bypassing it is often advisable to maintain separate analog and digital grounds throughout a complete system, tying them common in one place only. if the common tie-point is remote and acciden- tal disconnection of that one common tie-point occurs due to card removal with power on, a large differential voltage between the two commons could develop. to protect devices that inter- face to both digital and analog parts of the system, such as the ad558, it is recommended that common ground tie-points should be provided at each such device. if only one system ground can be connected directly to the ad558, it is recom- mended that analog common be selected. power supply considerations the ad558 is designed to operate from a single positive power supply voltage. specified performance is achieved for any supply voltage between +4.5 v and +16.5 v. this makes the ad558 ideal for battery-operated, portable, automotive or digital main- frame applications. *for additional insight, an ic amplifier users guide to decoupling, grounding and making things go right for a change, is available at no charge from any analog devices sales office.
ad558 rev. a C6C t w 2.0v 2.0v 0.8v 0.8v t ds t dh data inputs cs or ce t settling 1/2 lsb dac v output t w = storage pulse width = 200ns min t dh = data hold time = 10ns min t ds = data setup time = 200ns min t settling = dac output settling time to 1/2 lsb figure 7. ad558 timing use of v out sense separate access to the feedback resistor of the output amplifier allows additional application versatility. figure 8a shows how i r drops in long lines to remote loads may be cancelled by putting the drops inside the loop. figure 8b shows how the separate sense may be used to provide a higher output current by feeding back around a simple current booster. 15 16 ad558 12 13 v out 14 r l gnd gain select sense v out v out 0v to +10v a. compensation for i r drops in output lines 15 16 ad558 12 13 v out r l gnd gain select sense v out v out 0v to +2.56v v cc 2n2222 14 b. output current booster figure 8. use of v out sense optimizing settling time in order to provide single-supply operation and zero-based output voltage ranges, the ad558 output stage has a passive pull-down to ground. as a result, settling time for negative going output steps may be longer than for positive-going output steps. the relative difference depends on load resistance and capacitance. if a negative power supply is available, the negative-going settling time may be improved by adding a pull- down resistor from the output to the negative supply as shown in figure 9. the value of the resistor should be such that, at zero voltage out, current through that resistor is 0.5 ma max. bipolar output ranges the ad558 was designed for operation from a single power supply and is thus capable of providing only unipolar (0 v to +2.56 v and 0 v to 10 v) output ranges. if a negative supply is 15 16 ad558 v out r l sense v out v ee negative supply r p-d = 2x v ee (in k w) figure 9. improved settling time available, bipolar output ranges may be achieved by suitable output offsetting and scaling. figure 10 shows how a 1.28 volt output range may be achieved when a C5 volt power supply is available. the offset is provided by the ad589 precision 1.2 volt reference which will operate from a +5 volt supply. the ad544 output amplifier can provide the necessary 1.28 volt output swing from 5 volt supplies. coding is complementary offset binary. 14 15 16 ad558 12 13 ad589 ad544 0.01mf 0.01mf 0.01mf ?v ?.2v 4.7kw 5kw 4.53k w ?v input code v out 00000000 +128v 10000000 0v 11111111 ?.27v 1.5kw v o +1.28 to ?.27 5kw +5v 500w bipolar offset adjust v in v out = 0v to +2.56v figure 10. bi polar operation of ad558 from 5 v supplies measuring offset error one of the most commonly specified endpoint errors associated with real-world nonideal dacs is offset error. in most dac testing, the offset error is measured by applying the zero-scale code and measuring the output deviation from 0 volts. there are some dacs, like the ad558 where offset errors may be present but not observable at the zero scale, because of other circuit limitations (such as zero coinciding with single- supply ground) so that a nonzero output at zero code cannot be read as the offset error. factors like this make testing the ad558 a little more complicated. by adding a pulldown resistor from the output to a negative supply as shown in figure 11, we can now read offset errors at zero code that may not have been observable due to circuit limitations. the value of the resistor should be such that, at zero voltage out, current through the resistor is 0.5 ma max. output amp 16 15 14 13 agnd v out select v out sense v out ? 0.5ma a. 0 v to 2.56 v output range
ad558 rev. a C7C output amp 16 15 14 13 agnd v out select v out sense v out ? 0.5ma b. 0 v to 10 v output range figure 11. offset connection diagrams interfacing the ad558 to microprocessor data buses the ad558 is configured to act like a write only location in memory that may be made to coincide with a read only memory location or with a ram location. the latter case allows data previously written into the dac to be read back later via the ram. address decoding is partially complete for either rom or ram. figure 12 shows interfaces for three popular micropro- cessor systems. address bus data bus 6800 vma f 2 r/w ad558 v out db0?b7 16 8 8 ce cs address decoder 16 r/w ? ce gated decoded address ? cs a. 6800/ad558 interface address bus data bus 8080a ad558 v out db0?b7 16 8 8 ce cs address select pulse logic 16 memw memw ? ce decoded address select pulse ? cs b. 8080a/ad558 interface address bus data bus 1802 ad558 v out db0?b7 8 8 8 ce cs address latch & decode 8 mwr cdp 1802: mwr ? ce decoded address select pulse ? cs tpa ma 0 ?7 c. 1802/ad558 interface figure 12. interfacing the ad558 to microprocessors performance (typical @ +25 8 c, v cc 6 +5 v to +15 v unless otherwise noted) 0 lsb 1.75 1.50 1.25 1.00 0.75 0.50 0.25 ?.25 ?.50 ?.75 ?.00 ?5 ?5 0 +25 +50 +75 +100 +125 o c full scale error all ad558 ad558s, t 1lsb = 0.39% of full scale figure 13. full-scale accuracy vs. temperature performance of ad558 0 lsb 1/2 1/4 ?5 ?5 0 +25 +50 +75 +100 +125 o c zero error all ad558 ad558s, t 1lsb = 0.39% of full scale ?/4 ?/2 figure 14. zero drift vs. temperature performance of ad558
ad558 rev. a C8C printed in u.s.a. c558fC21C8/87 ma 16 14 4 6 81012141618 volts i cc v cc 12 10 figure 15. quiescent current vs. power supply voltage for ad558 figure 16. ad558 settling characteristics detail 0 v to 2.56 v output range full-scale step figure 17. ad558 settling characteristic detail 0 v to 10 v output range full-scale step figure 18. ad558 logic timing outline dimensions dimensions shown in inches and (mm). n (plastic) package d (ceramic) package p (plcc) package
|
