25 3 db 90 card couplers hd-m series features 1.high performance the high frequency characteristics feature. extremely low loss and a high degree of matching. 2.power uniform distribution and 90 phase difference type this is a one input, two output (or two input, one output) power uniform distribution type having a 90 phase difference between the two outputs (or two inputs). 3.miniature and lightweight corrosion-resistant aluminum is used for the cover and the hirose electric original pattern design, which uses a stripline triplate method, enables the couplers to be extremely small and lightweight. 4.equipped with tabs tabs permit direct mounting to surface circuits. 5.high power type this type can be used with up to 100 w of power. product specifications note: the frequency range and the maximum input power will differ depending on the products. the test method conforms to mil-std-202. materials ratings frequency range (note) characteristic impedance maximum input power (note) 30 to 6400 mhz 50 ohm 50 to 100 w operating temperature range operating relative humidity C10? to + 65? 95% max. item standard conditions part material finish cover (a) stainless steel --------- cover (b) aluminum conductive white alumite board dielectric gold plating rivets aluminum --------- eyelet brass nickel plating tabs phosphor bronze gold plating cover (a) stainless steel --------- cover (b) stainless steel --------- 1. insulation resistance 500m ohms min 100 v dc 2.vibration frequency of 10 to 2000 hz, overall amplitude of 1.52 mm, acceleration of 98 m/s 2 for 2 hours in each of 3 directions 3.shock acceleration of 980 m/s 2 , sine half-wave waveform, 3 cycles in each of the 3 axis temperature : C 55 ? +5? to +35? +85? +5? to +35? 4.temperature cycle no damage, cracks, or parts dislocation time : 30 15 max. 30 15 max. (minutes) 5 cycles 5. corrosion resistance no serious corrosion exposed to 20% salt water solution for 48 hours 6. hydrogen sulfide gas no serious corrosion exposed to 10% potassium sulfide solution for 100 hours no damage, cracks, or parts dislocation no damage, cracks, or parts dislocation hd-0053m3-ih(40) hd-0195m3-dh(40) hd-0195m3-dh-1(40) hd-0900m3-ch-1(40) hd-0620m3-eh(40) hd-1700m3-fh(40) hd-3900m3-bh(40) hd-0313m3-fh(40) hd-2100m3-ch(40) hd-1800m3-ch(40) hd-3200m3-bh(40) hd-6150m3-ah(40) the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information.
ordering information hd 0195m 3 - d h - 1 ( 40 ) 1 2 3 4 7 5 6 - series name: hd (directional couplers) center frequency(mhz) examples 0053m: 53mhz 0300m: 300mhz 6150m:6150mhz 1 2 coupling 3:3db frequency relative bandwidth c:from 10% to below 15% d:from 15% to below 20% e:from 20% to below 25% f:from 25% to below 30% g:from 30% to below 35% 3 4 form h:h type suffix ( 40 ) : rohs compliant 5 6 7 specifications part number frequency range (mhz) coupling (db) frequency sensitivity (db) isoiation (db min) v.s.w.r. (max) weight (g) power (w) fig hd-0053m3-ih ( 40 ) 30 ~ 76 0.75 15 1.40 22 100 1 hd-0070m3-gh ( 40 ) 45 ~ 85 0.5 20 1.20 25 50 2 hd-0125m3-gh ( 40 ) 80 ~ 160 0.5 20 1.20 22 100 2 hd-0155m3-ih ( 40 ) 90 ~ 220 0.8 20 1.20 23 100 2 hd-0195m3-dh ( 40 ) 160 ~ 230 0.5 20 1.20 22 100 2 hd-0195m3-dh-1 ( 40 ) 160 ~ 230 0.5 20 1.20 11 100 1 hd-0300m3-fh ( 40 ) 225 ~ 400 0.5 20 1.20 10 100 2 hd-0300m3-fh-1 ( 40 ) 225 ~ 400 0.5 20 1.20 9 100 1 hd-0313m3-fh ( 40 ) 225 ~ 400 0.5 20 1.20 6 100 3 hd-0430m3-ch ( 40 ) 360 ~ 470 0.3 20 1.20 10 100 2 hd-0620m3-eh ( 40 ) 470 ~ 770 0.5 20 1.20 6 100 2 hd-0660m3-gh ( 40 ) 470 ~ 880 0.6 19 1.20 6 100 2 26 hd-m series 3 db 90 card couplers yes rohs 3 +0.35 3 +0.35 3 +0.3 5 3 +0.3 5 3 +0.3 5 3 +0.3 5 3 +0.3 5 3 +0.3 5 3 +0.3 5 3 +0.35 3 +0.35 3 +0.35 0 0 0 0 0 0 0 0 0 0 0 0 the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information.
3 +0.35 3 +0.35 3 +0.35 3 +0.35 3 +0.35 3 +0.35 3 +0.35 3 +0.35 3 + 0.35 3 +0.35 3 +0.35 3 +0.45 3 +0.45 3 +0.45 3 +0.45 3 +0.45 27 hd-m series 3 db 90 card couplers specifications there is a 90 phase difference between the output and the coupling. the v.s.w.r. has a common standard for both the primary line and the secondary line. part number frequency range. (mhz) coupling (db) frequency sensitivity (db) isolation (db min) v.s.w.r. (max) weight (g) power (w) fig. hd-0660m3-gh-1 ( 40 ) 440~880 0.6 20 1.20 6 100 1 hd-0700m3-fh ( 40 ) 500~900 0.5 20 1.20 6 100 2 hd-0750m3-gh ( 40 ) 500~1,000 0.5 20 1.20 5 100 1 hd-0900m3-ch ( 40 ) 800~1,000 0.3 20 1.20 6 100 2 hd-0900m3-ch-1 ( 40 ) 800~1,000 0.3 20 1.20 6 100 1 hd-0900m3-ch-2 ( 40 ) 800~1,000 0.3 20 1.20 6 100 3 hd-1500m3-gh ( 40 ) 1,000~ 2,000 0.6 20 1.25 4 100 4 hd-1700m3-fh ( 40 ) 1,200~ 2,200 0.5 20 1.20 5 50 5 hd-1800m3-ch ( 40 ) 1,600~ 2,000 0.3 20 1.20 3 50 6 hd-1900m3-ch ( 40 ) 1,700~ 2,100 0.3 20 1.20 3 50 6 hd-2100m3-ch ( 40 ) 1,900~ 2,300 0.3 20 1.20 3 50 6 hd-2400m3-bh ( 40 ) 2,200~ 2,600 0.5 20 1.20 3 100 8 hd-2500m3-bh ( 40 ) 2,300~ 2,700 0.3 21 1.25 3 100 6 hd-3200m3-bh ( 40 ) 3,000~ 3,400 0.3 18 1.30 3 100 6 hd-3900m3-bh ( 40 ) 3,600~ 4,200 0.5 18 1.30 7 100 7 hd-6150m3-ah ( 40 ) 5,900~ 6,400 0.5 18 1.30 7 100 7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 yes rohs the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information.
28 hd-m series 3 db 90 card couplers external dimensions hd-0053m3-ih ( 40 ) 28.0 44.5 53.3 50.8 44.5 3.2 28.0 44.5 3.6 hd-0195m3-dh-1 ( 40 ) 17.3 26.9 36.3 38.1 31.8 2.9 17.3 31.8 3.3 hd-0300m3-fh-1 ( 40 ) 12.7 21.8 31.8 31.8 25.4 3.1 12.7 25.4 3.5 hd-0660m3-gh-1 ( 40 ) 7.9 17.8 25.4 25.4 19.1 3.1 7.9 19.1 3.5 hd-0750m3-gh ( 40 ) 8.0 16.8 25.4 22.2 15.9 3.2 8.0 15.9 3.6 hd-0900m3-ch-1 ( 40 ) 8.0 17.0 25.5 22.5 15.9 3.4 8.0 15.9 3.8 abcde fgh hd-0900m3-ch ( 40 ) 8.0 17.0 25.5 22.5 15.9 3.0 8.0 15.9 hd-0620m3-eh ( 40 ) 8.0 17.0 25.5 22.5 15.9 3.1 8.0 15.9 hd-0430m3-ch ( 40 ) 12.8 21.8 32.0 32.0 25.4 3.0 12.8 25.4 hd-0300m3-fh ( 40 ) 12.8 21.8 32.0 32.0 25.4 3.2 12.8 25.4 hd-0195m3-dh ( 40 ) 28.0 37.1 46.1 51.0 44.5 3.0 28.0 44.5 hd-0155m3-i h ( 40 ) 28.0 37.1 46.1 51.0 44.5 3.4 28.0 44.5 hd-0125m3-gh ( 40 ) 28.0 37.1 46.1 51.0 44.5 3.2 28.0 44.5 hd-0070m3-gh ( 40 ) 28.0 44.5 53.5 51.0 44.5 3.2 28.0 44.5 hd-0660m3-gh ( 40 ) 8.0 17.0 25.5 22.5 15.9 3.3 8.0 15.9 hd-0700m3-fh ( 40 ) 8.0 17.0 25.5 22.5 15.9 3.1 8.0 15.9 part number part number a bcdefg h i fig.1 fig.2 dimensions of mounting holes dimensions of mounting holes the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information.
29 hd-m series 3 db 90 card couplers hd-1500m3-gh ( 40 ) 14.0 26.7 34.3 12.7 3.2 14.0 3.6 hd-1700m3-fh ( 40 ) 10.35 11.7 20.7 20.7 14.3 3.3 14.3 part number hd-0313m3-fh ( 40 ) hd-0900m3-ch-2 ( 40 ) a 38.1 38.1 b 45.7 45.7 c 50.8 50.8 d 12.7 12.7 e 6.4 6.4 f 3.2 3.2 g 38.1 38.1 h 6.4 6.4 i 3.6 3.6 part number a b cd e f g part number a b cd e f g fig.3 fig.4 fig.5 dimensions of mounting holes dimensions of mounting holes dimensions of mounting holes the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information.
hd-2400m3-bh ( 40 ) fig.8 part number abcdef hd-2100m3-ch ( 40 ) 40.2 26.8 46.6 10.0 2.8 40.2 hd-1900m3-ch ( 40 ) 40.2 26.8 46.6 10.0 2.8 40.2 hd-1800m3-ch ( 40 ) 40.2 26.8 46.6 10.0 2.8 40.2 hd-3200m3-bh ( 40 ) 25.1 15.1 31.1 10.0 3.3 25.1 hd-2500m3-bh ( 40 ) 40.2 26.8 46.6 10.0 3.1 40.2 part number abcdefgh hd-3900m3-bh ( 40 ) 17 22 42 15 8.5 3.2 17 8.5 hd-6150m3-ah ( 40 ) 17 22 42 15 8.5 3.2 17 8.5 fig.6 fig.7 dimensions of mounting holes dimensions of mounting holes dimensions of mounting holes 30 hd-m series 3 db 90 card couplers the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information.
31 hd-m series 3 db 90 card couplers typical data temperature test data < hd-1800m3-ch ( 40 ) > ( 40 ) ( 40 ) ( 40 ) low temperature (-10 ? ) normal temperature (+20? ) high temperature (+65 ?) the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information.
32 hd-m series 3 db 90 card couplers mounting method figure 1. figure 3. figure 4. fastening screw microstrip board micro stripline tab figure 2. the three types of mounting methods illustrated in the diagrams below will mount the card coupler for use under optimum conditions. the fastening screws in the diagrams are m2 screws tightened to 1.5 kg ? cm. when the tip of the micro stripline is of fluoropolymer material ( r = 2.6), c chamfering of c1 is performed at t1.6, and of c0.5 at t1.2. the side view diagrams of figure 1 are illustrated in figures 2, 3, and 4 below. gap s between the card coupler and the microstrip board surface should be used to agree with the following conditions. below 500 mhz ........ s 0.5 mm 500 to 2300 mhz ...... s 0.25 mm above 2300 mhz ...... s 0.15 mm ( metal plate or conductive spacer when the ground board is constructed of 0.4 mm stainless and 0.8 mm aluminum (when the thickness of the microstrip board is 1.6 or 1.2 mm) for t1.6 boards, use with the stainless case of the card coupler facing upward. for t1.2 boards, use with the aluminum case of the card coupler facing upward. mount and fix the card coupler with fastening screws as illustrated in figure 2. next, solder the tabs and micro stripline, then use. (when the thickness of the microstrip board is greater than 1.6 mm) insert a metal plate or a conductive spacer between the coupler and ground, then mount as illustrated in figure 3 so that the surface of the tabs and the position of the microstrip board are equal. fix the card coupler with fastening screws as illustrated in figure 3. next, solder the tabs and micro stripline, then use. (when the thickness of the microstrip board is less than 1.2 mm) cut the ground at the position of the coupler and attach so that the surface of the tabs is in contact with the micro stripline. fix the card coupler with fastening screws as illustrated in figure 4. next, solder the tabs and micro stripline, then use. the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information.
33 for ve items (in which aluminum is used above and below the ground board and the eyelets protrude beyond the cover) the height of the cover will be a value 0.1 mm less than one half of the overall thickness. for directional card couplers ( hd-0900m (10 db) and hd-0900m (20 db),etc. ) the height of the cover will be a value 0.35 mm less than one half of the overall thickness. ( when spacing h of the micro stripline board and the tabs is 0 h 0.3 mm ) fix the card coupler with fastening screws as illustrated in figure 2. next, solder the tabs and micro stripline, then use. ( when spacing h of the micro stripline board and the tabs is h < 0 ) insert a metal plate or a conductive spacer between the coupler and ground, then mount as illustrated in figure 3 so that the surface of the tabs and the position of the microstrip board are equal. fix the card coupler with fastening screws as illustrated in figure 3. next, solder the tabs and micro stripline, then use. ( when spacing h of the micro stripline board and the tabs is h > 0.3 mm ) cut the ground at the position of the coupler and attach so that the surface of the tabs is in contact with the micro stripline. fix the card coupler with fastening screws as illustrated in figure 4. next, solder the tabs and micro stripline, then use. at the time of soldering, solder with a space of 1 mm from the edge of the micro stripline as illustrated in figure 5. figure 5. micro stripline board soldering portion hd-m series 3 db 90 card couplers the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information.
34 hd-m series 3 db 90 card couplers notes : the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information.
|
