bipolar analog integrated circuit pc4559 high performance dual operational amplifier data sheet document no. g12984ej6v0ds00 (6th edition) date published march 2004 n cp(k) printed in japan the mark shows major revised points. the information in this document is subject to change without notice. before using this document, please confirm that this is the latest version. not all products and/or types are available in every country. please check with an nec electronics sales representative for availability and additional information. 1987 description the pc4559 is a dual type operational amplifier having better slew rate and bandwidth than the pc4558c with satisfying unity gain frequency compensation. having low noise characteristics, this device is very convenient to make active filters and other audio application circuits. features ? internal frequency compensation ? low noise ? output short circuit protection ordering information part number package pc4559c 8-pin plastic dip (7.62 mm (300)) equivalent circuit (1/2 circuit) r 1 r 9 q 5 q 7 q 13 q 11 r 5 r 7 r 8 out q 2 q 1 q 8 9 q r 3 q 10 r 4 r 2 c 1 i i i n v v + ? q 15 q 4 q 3 c 2 d q 14 q 12 r 6 ? + q 6 pin configuration (top view) pc4559c 1 1 2 3 4 8 7 6 5 v + out 2 i i2 i n2 + ? i i1 i n1 out 1 v ? 2 + ?
data sheet g12984ej6v0ds 2 pc4559 absolute maximum ratings (t a = 25c) parameter symbol ratings unit voltage between v + and v ? note 1 v + - v ? ?0.3 to +36 v differential input voltage v id 30 v input voltage note 2 v i v ? ?0.3 to v + +0.3 v output voltage note 3 v o v ? ?0.3 to v + +0.3 v power dissipation note 4 p t 350 mw output short circuit duration note 5 indefinite sec operating ambient temperature t a ?20 to +80 c storage temperature t stg ?55 to +125 c notes 1. reverse connection of supply voltage can cause destruction. 2. the input voltage should be allowed to input without damage or destruction. even during the transition period of supply voltage, power on/off etc., this s pecification should be kept. the normal operation will establish when the both inputs are within the common mode input voltage range of electrical characteristics. 3. this specification is the voltage which should be allowed to supply to the output terminal from external without damage or destructive. even during the transition period of supply voltage, power on/off etc., this specification should be kept. the output voltage of normal operation will be the output voltage swing of electrical characteristics. 4. thermal derating factor is ?5.0 mv/c when ambient temperature is higher than 55c. 5. pay careful attention to the total power dissipation not to exceed the absolute maximum ratings, note 4. recommended operating conditions parameter symbol min. typ. max. unit supply voltage v 4 16 v
data sheet g12984ej6v0ds 3 pc4559 electrical specifications (t a = 25c, v = 15 v) parameter symbol conditions min. typ. max. unit input offset voltage v io r s 10 ? 0.5 6.0 mv input offset current note i io 5 200 na input bias current note i b 60 500 na large signal voltage gain a v r l 20 k ? , v o = 10 v 20,000 100,000 power consumption p d i o = 0 a 90 170 mw common mode rejection ratio cmr r s 10 k ? 70 90 db supply voltage rejection ratio svr r s 10 k ? 30 150 v/v r l 10 k ? 12 14 v output voltage swing v om r l 2 k ? 10 13 v common mode input voltage range v icm 12 14 v slew rate sr a v = 1 2.0 v/ s input equivalent noise voltage v n r s = 1 k ? , f = 1 hz to 1 khz (figure1) 6 v p-p channel separation f = 1 khz (figure2) 105 db note input bias currents flow out from ic, because each curr ents are base current of pnp-transistor on input stage. measurement circuit figure1 noise measurement circuit 50 ? 1 k ? ? 15 v ? + 1 k ? 100 k ? +15 v v o v n = v o 2000 figure2 channel separa tion measurement circuit 50 k ? ? + 50 ? v o2 v o1 channel separation = 20 log ( ) 1 1000 v o2 v o1 ? + 10 k ? 10 k ?
data sheet g12984ej6v0ds 4 pc4559 typical performance characteristics (t a = 25c, typ.) 20 1 10 100 1 k 10 k 100 k 1 m 10 m 600 500 400 300 200 100 120 100 80 60 40 20 0 40 60 80 100 100 1 k 10 k 100 k 1 m 100 1 k 10 k 32 28 24 20 16 12 8 4 0 30 25 20 15 10 5 100 80 60 40 20 0 200? c /w power dissipation p t - total power dissipation -mw t a - operating ambient temperature - ? c 0 open loop frequency response a v - open loop voltage gain - db f- frequency - hz large signal frequency response v om - output voltage swing - v p-p f - frequency - hz = 15 v v + _ _ + outout voltage swing v om - output voltage swing -v p-p r l - load resistance - ? = 15 v v + _ _ + input bias current i b - input bias current - na t a - operating ambient temperature - ? c 0 4 3 2 1 supply current i cc - supply current - ma 20 _ + 10 _ + 020406080 ? 20 = 15 v v + _ _ + = 15 v v + _ _ + v - supply voltage - v _ +
data sheet g12984ej6v0ds 5 pc4559 0 20 10 0 ? 10 ? 20 10 5 0 ? 5 ? 10 1 10 100 1 k 1000 300 100 30 10 common mode input voltage range v icm - common mode input range -v input equivalent noise voltage density f - frequency - hz v o - output voltage - v voltage follower pulse response 20 v - supply voltage - v _ + 10 40 30 20 10 0 = 15 v v + _ _ + e n -input equivalent noise voltage density - nv/ hz t - time - s
data sheet g12984ej6v0ds 6 pc4559 package drawing (unit : mm) 14 85 item millimeters notes 1. each lead centerline is located within 0.25 mm of its true position (t.p.) at maximum material condition. p8c-100-300b,c-2 n 0.25 p 0.9 min. r0 15 a 10.16 max. b 1.27 max. f 1.4 min. g 3.2 0.3 j 5.08 max. k 7.62 (t.p.) c 2.54 (t.p.) d 0.50 0.10 h 0.51 min. i 4.31 max. l 6.4 m 0.25 + 0.10 ? 0.05 2. ltem "k" to center of leads when formed parallel. m a r m p i j h g f dn c b 8-pin plastic dip (7.62mm(300)) l k
data sheet g12984ej6v0ds 7 pc4559 recommended soldering conditions the pc4559 should be soldered and mounted under the following recommended conditions. for soldering methods and conditions other than those recommended below, contact an nec electronics sales representative. for technical information, see the following website. semiconductor device mount manual (http://www.necel.com/pkg/en/mount/index.html) type of through-hole device pc4559c: 8-pin plastic dip (7.62 mm (300)) process conditions wave soldering (only to leads) solder temperature: 260c or below, flow time: 10 seconds or less. partial heating method pin temperature: 300c or below, heat time: 3 seconds or less (per each lead). caution for through-hole device, the wave soldering process must be applied only to leads, and make sure that the package body does not get jet soldered.
pc4559 the information in this document is current as of march, 2004. the information is subject to change without notice. for actual design-in, refer to the latest publications of nec electronics data sheets or data books, etc., for the most up-to-date specifications of nec electronics products. not all products and/or types are available in every country. please check with an nec electronics sales representative for availability and additional information. no part of this document may be copied or reproduced in any form or by any means without the prior written consent of nec electronics. nec electronics assumes no responsibility for any errors that may appear in this document. nec electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of nec electronics products listed in this document or any other liability arising from the use of such products. no license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of nec electronics or others. descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. the incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. nec electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. while nec electronics endeavors to enhance the quality, reliability and safety of nec electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. to minimize risks of damage to property or injury (including death) to persons arising from defects in nec electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. nec electronics products are classified into the following three quality grades: "standard", "special" and "specific". the "specific" quality grade applies only to nec electronics products developed based on a customer- designated "quality assurance program" for a specific application. the recommended applications of an nec electronics product depend on its quality grade, as indicated below. customers must check the quality grade of each nec electronics product before using it in a particular application. "standard": computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "special": transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). "specific": aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. the quality grade of nec electronics products is "standard" unless otherwise expressly specified in nec electronics data sheets or data books, etc. if customers wish to use nec electronics products in applications not intended by nec electronics, they must contact an nec electronics sales representative in advance to determine nec electronics' willingness to support a given application. (note) (1) "nec electronics" as used in this statement means nec electronics corporation and also includes its majority-owned subsidiaries. (2) "nec electronics products" means any product developed or manufactured by or for nec electronics (as defined above). ? ? ? ? ? ? m8e 02. 11-1
|
