View AFCT-5760ANLZ_6778944.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

afct-5760xnxz and afct-5765xnxz families of small form factor pluggable (sfp) optical transceivers for single-mode oc3/stm-1 with optional dmi part of the avago technologies metrak family data sheet description the afct-576 x z family of sfp optical transceivers for oc3 offers the customer a range of design options, including optional dmi (further described later), extended or industrial temperature ranges, and standard push-button or or bail delatch. the afct- 5765z family targets applications requiring dmi features, and the afct-5760z family is streamlined for those applications where dmi features are not needed. throughout this document, afct-576 x z will refer collectively to the entire product family encompassing this range of product features. part number options the afct-576 x z family consists of the following products: with dmi part number temperature design afct-5765nlz extended* standard afct-5765npz exten ded* bail afct-5765anlz industrial* standard afct-5765anpz industrial* bail without dmi part number temperature design afct-5760nlz extended* standard afct-5760npz exten ded* bail AFCT-5760ANLZ industrial* standard afct-5760anpz industrial* bail * extended temperature range is -10 to 85 degrees c industrial temperature range is -40 to 85 degrees c features ? rohs compliant ? optional digital diagnostic monitoring available - afct-5760z family: without dmi - afct-5765z family: with dmi ? per sff-8472, diagnostic features on afct-5765z family enable diagnostic monitoring interface for optical transceivers with real-time monitoring of: - transmitted optical power - received optical power - laser bias current - temperature - supply voltage ? compliant with sff-8074i sfp transceiver specification ? compliant with itu-t g957 stm-1 l1.1 (40km) optical interface ? compliant with telcordia gr253 oc3 lr-1 (40km) optical interface ? class 1 cdrh/iec 825 eye safety compliant ? operating case temperature range C10 c to +85 c (extended) C40 c to +85 c (industrial) ? multitrate operation from 125 mb/s to 155 mb/s ? lc duplex fiber connector ? manufactured in an iso 9001 compliant facility applications ? atm switches and routers ? sonet/sdh switch infrastructure ? broadband aggregation applications ? metro edge switching ? metro and access multi-service platforms ? suitable for fast ethernet applications related products ? afct-5755z family of oc12 sfp transceivers with dmi ? afct-5745l/p family of oc48 sfp transceivers with dmi
2 text photo-detector amplification & quantization laser laser driver & safety circuit electrical interface rd+ (receive data) rd- (receive data) rx loss of signal mod-def2 (sda) tx_disable td+ (transmit data) td- (transmit data) tx_fault mod-def0 mod-def1 (scl) receiver transmitter optical interface light from fiber light to fiber controller & memory figure 1. transceiver functional diagram general features the afct-576 x z family of sfp optical transceivers are high performance, cost effective modules for serial optical data communications applications ranging from 125-155 mbps. they are designed to provide sonet/ sdh compliant connections for 155 mbps at short and intermediate reach links. this includes specifications for the signal coding, optical fiber and connector types, optical and electrical transmitter characteristics, optical and electrical receiver characteristics, jitter characteristics, and compliance testing methodology for the aforementioned. these transceivers are qualified in accordance with gr-468-core. the transmitter section of the transceivers incorporate a 1300nm fabry perot (fp) laser. for each device the receiver section uses an movpe grown planar pin photodetector for low dark current and excellent responsivity. a positive-ecl logic interface simplifies interface to external circuitry. the receiver section contains an ingaas/inp photo detector and a preamplifier mounted in an optical subassembly. this optical subassembly is coupled to a postamplifier/decision circuit on a circuit board. the afct-576xz family of optical transceivers adds digital diagnostic monitoring to standard sfp functionality, enabling fault isolation, components monitoring and failure prediction capabilities. sfp msa compliance the product package is compliant with the sfp msa with the lc connector option. the sfp msa includes specifications for mechanical packaging and performance as well as dc, ac and control signal timing and performance. the power supply is 3.3 v dc. the high speed i/o (hsio) signal interface is a low voltage differential type. it is ac coupled and terminated internally to the module. the internal termination is a 100 ohm differential load. installation the afct-576 x z can be installed in any sff-8074i compliant small form pluggable (sfp) port regardless of host equipment operating status. the module is hot- pluggable, allowing it to be installed while the host system is operating and online. upon insertion, the transceiver housing makes initial contact with the host board sfp cage, mitigating potential damage due to electrostatic discharge (esd).
3 laser driver & safety circuitry 50 ? 50 ? so+ so? amplification & quantization 50 ? 50 ? si+ si? vrefr vrefr tbc ewrap rbc rx_rate rx_los gpio(x) gpio(x) gp14 refclk tx_fault tbc ewrap rbc rx_rate refclk tx[0:9] rx[0:9] tx_fault tx_disable td+ td? tx gnd mod_def2 eeprom mod_def1 mod_def0 rx gnd 4.7 k to 10 k ? 3.3 v 4.7 k to 10 k ? 3.3 v 4.7 k to 10 k ? 4.7 k to 10 k ? protocol ic sfp module v cc ,t 1 h 1 h 10 f 0.1 f 3.3 v 4.7 k to 10 k ? 10 f 0.1 f 0.1 f 4.7 k to 10 k ? rd+ rd? rx_los 0.01 f 0.01 f 100 ? 0.01 f 0.01 f v cc ,r 100 ? 50 ? v cc ,r 50 ? v cc ,r transmitter section the transmitter section includes a 1310 nm fabry-perot laser and a transmitter driver circuit. the driver circuit maintains a constant optical power level provided that the data pattern is valid for nrz code. connection to the transmitter is provided via a lc optical connector. the transmitter has full iec 825 and cdrh class 1 eye safety. tx_disable the transmitter output can be disabled by asserting pin 3, tx_disable. a high signal asserts this function while a low signal allows normal laser operation. the transmitter output can also be disabled and monitored via the 2-wire serial interface. in the event of a transceiver fault, such as the activation of the eye safety circuit, toggling of the tx_disable will reset the transmitter, as depicted in figure 2. figure 2. typical application configuration tx_fault a laser fault or a low v cc condition will activate the transmitter fault signal, tx_fault, and disable the laser. this signal is an open collector output (pull-up required on the host board); a low signal indicates normal laser operation and a high signal indicates a fault. the tx_fault will be latched high when a laser fault occurs and is cleared by toggling the tx_disable input or power cycling the transceiver. the tx_fault is not latched for low v cc . the transmitter fault condition can also be monitored via the two-wire serial interface (address a2, byte 110, bit 2). eye safety circuit under normal operating conditions, the laser power will be maintained below the eye-safety limit. if the eye safety limit is exceeded at any time, a laser fault will occur and the tx_fault output will be activated.
4 figure 3. msa required power supply filter v cc t 0.1 f 0.1 f 10 f 1 h 1 h 0.1 f 10 f 3.3 v sfp module v cc r host board receiver section the receiver section for the afct-576 x z contains an ingaas/inp photo detector and a preamplifier mounted in an optical subassembly. this optical subassembly is coupled to a post amplifier/decision circuit on a circuit board. the design of the optical subassembly provides better than 12 db optical return loss (orl). connection to the receiver is provided via a lc optical connector. rx_los the receiver section contains a loss of signal (rx_los) circuit to indicate when the optical input signal power is insufficient for sonet/sdh compliance. a high signal indicates loss of modulated signal, indicating link failure such as a broken fiber or a failed transmitter. rx_los can be also be monitored via the two-wire serial (address a2, byte 110, bit 1). functional data i/o avagos afct-576 x z transceiver is designed to accept industry standard differential signals. the transceiver provides an ac-coupled, internally terminated data interface. bias resistors and coupling capacitors have been included within the module to reduce the number of components required on the customers board. figure 2 illustrates the recommended interface circuit. digital diagnostic interface and serial identification the afct-576 x z family complies with the sff-8074i specification, which defines the modules serial identification protocol to use the 2-wire serial cmos eeprom protocol of the atmel at24c01a or similar. standard sfp eeprom bytes 0-255 are addressed per sff-8074i at memory address 0xa0 (a0h). as an enhancement to the conventional sfp interface defined in sff-8074i, the afct-5765z is also compliant to sff-8472 (the digital diagnostic interface for sfp). this enhancement adds digital diagnostic monitoring to standard sfp functionality, enabling failure prediction, fault isolation, and component monitoring capabilities. using the 2-wire serial interface, the afct-5765z provides real time access to transceiver internal supply voltage and temperature, transmitter output power, laser bias current and receiver average input power, allowing a host to predict system compliance issues. these five parameters are internally calibrated, per the msa. new digital diagnostic information is accessed per sff-8472 using eeprom bytes 0-255 at memory address 0xa2 (a2h). the digital diagnostic interface also adds the ability to disable the transmitter (tx_disable), monitor for transmitter faults (tx_fault) and monitor for receiver loss of signal (rx_los). contents of the msa-compliant serial id memory are shown in tables 3 to 7. the sff-8074i and sff-8472 specifications are available from the sff committee at http://www.sffcommittee.org. predictive failure identification the diagnostic information allows the host system to identify potential link problems. once identified, a fail- over technique can be used to isolate and replace suspect devices before system uptime is impacted. compliance prediction the real-time diagnostic parameters can be monitored to alert the system when operating limits are exceeded and compliance cannot be ensured. fault isolation the diagnostic information can allow the host to pinpoint the location of a link problem and accelerate system servicing and minimize downtime. component monitoring as part of the host system monitoring, the real time diagnostic information can be combined with system level monitoring to ensure system reliability. application support an evaluation kit and reference designs are available to assist in evaluation of the afct-576 x z sfps. please contact your local field sales representative for availability and ordering details.
5 feature test method performance electrostatic discharge (esd) to the electrical pins mil-std-883c method 3015.4 jedec/eia jesd22-a114-a class 2 (2000 volts) electrostatic discharge (esd) to the duplex lc receptacle bellcore gr1089-core 25 kv air discharge 10 zaps at 8 kv (contact discharge) on the electrical faceplate on panel. electromagnetic interference (emi) fcc class b applications with high sfp port counts are expected to be compliant; however, margins are dependent on customer board and chassis design. immunity variation of iec 61000-4-3 no measurable effect from a 10 v/m field swept from 80 to 1000 mhz applied to the transceiver without a chassis enclosure. eye safety us fda cdrh ael class 1 en (iec) 60825-1, 2, en60950 class 1 cdrh accession number: 9521220-137 tuv certificate number: 933/21205741/040 component recognition underwriter's laboratories and canadian standards association joint component recognition for information technology equipment including electrical business equipment ul file # e173874 rohs compliance reference to eu rohs directive 2002/95/ec operating temperature the afct-576 x z family is available in either extended (-10 to +85c) or industrial (-40 to +85c) temperature ranges. power supply noise the afct-576 x z can withstand an injection of psn on the v cc lines of 100 mv ac without a degradation in eye mask margin to 10% on the transmitter and a 1 db sensitivity penalty on the receiver. this occurs when the product is used in conjunction with the msa recommended power supply filter shown in figure 3. regulatory compliance the transceiver regulatory compliance is provided in table 1 as a figure of merit to assist the designer. the overall equipment design will determine the certification level. table 1. regulatory compliance
6 electrostatic discharge (esd) there are two conditions in which immunity to esd damage is important: the first condition is static discharge to the transceiver during handling such as when the transceiver is inserted into the transceiver port. to protect the transceiver, it is important to use normal esd handling precautions including the use of grounded wrist straps, work benches, and floor mats in esd controlled areas. the esd sensitivity of the afct-576 x z is compatible with typical industry production environments. the second condition is static discharge to the exterior of the host equipment chassis after installation. to the extent that the duplex lc optical interface is exposed to the outside of the host equipment chassis, it may be subject to system-level esd requirements. the esd performance of the afct-576 x z exceeds typical industry standards. table 1 documents esd immunity to both of these conditions. electromagnetic interference (emi) most equipment designs using the afct-576 x z sfps are subject to the requirements of the fcc in the united states, cenelec en55022 (cispr 22) in europe and vcci in japan. the metal housing and shielded design of the transceiver minimize emi and provide excellent emi performance. emi immunity the afct-576 x z transceivers have a shielded design to provide excellent immunity to radio frequency electromagnetic fields which may be present in some operating environments. eye safety the afct-576 x z transceivers provide class 1 eye safety by design. avago technologies has tested the transceiver design for regulatory compliance, under normal operating conditions and under a single fault condition. see table 1. flammability the afct-576 x z family of sfps is compliant to ul 94v- 0. customer manufacturing processes this module is pluggable and is not designed for aqueous wash, ir reflow, or wave soldering processes. caution the afct-576 x z contains no user-serviceable parts. tampering with or modifying the performance of the afct-576 x z will result in voided product warranty. it may also result in improper operation of the transceiver circuitry, and possible over-stress of the laser source. device degradation or product failure may result. connection of the afct-576 x z to a non-approved optical source, operating above the recommended absolute maximum conditions may be considered an act of modifying or manufacturing a laser product. the person(s) performing such an act is required by law to re-certify and re-identify the laser product under the provisions of u.s. 21 cf. handling precautions the afct-576 x z can be damaged by current surges or overvoltage. power supply transient precautions should be taken, and normal handling precautions for electrostatic sensitive devices should be taken. optical power budget the worst-case optical power budget (opb) in db for a fiber-optic link is determined by the difference between the minimum transmitter output optical power (dbm avg) and the lowest receiver sensitivity (dbm avg). this opb provides the necessary optical signal range to establish a working fiber-optic link. the opb is allocated for the fiber-optic cable length and the corresponding link penalties. for proper link performance, all penalties that affect the link performance must be accounted for within the link optical power budget. process plug this transceiver is supplied with a process plug for protection of the optical port within the lc connector receptacle. this process plug prevents contamination during handling, shipping and storage. it is made of a high-temperature, molded sealing material that can withstand +85 c. lc sfp cleaning recommendations in the event of contamination of the optical ports, the recommended cleaning process is the use of forced nitrogen. if contamination is thought to have remained, the optical ports can be cleaned using a ntt international cletop stick type (diam. 1.25 mm) and hfe7100 cleaning fluid.
7 notes: 1. tx fault is an open collector/drain output, which should be pulled up with a 4.7k C 10k ? resistor on the host board. pull up voltage between 2.0 v and vcct, r+0.3 v. when high, output indicates a laser fault of some kind. low indicates normal operation. in th e low state, the output will be pulled to < 0.8 v 2. tx disable input is used to shut down the laser output per the state table below with an external 4.7 - 10 k ? pull-up resistor. low (0 - 0.8 v): transmitter on between (0.8 v and 2.0 v): undefined high (2.0 - 3.465 v): transmitter disabled open: transmitter disabled 3. mod-def 0,1,2. these are the module definition pins. they should be pulled up with a 4.7 - 10 k ? resistor on the host board to a supply less than vcct +0.3 v or vccr+0.3 v. mod-def 0 is grounded by the module to indicate that the module is present mod-def 1 is clock line of two wire serial interface for optional serial id mod-def 2 is data line of two wire serial interface for optional serial id 4. los (loss of signal) is an open collector/drain output which should be pulled up externally with a 4.7k - 10 k ? resistor on the host board to a supply < vcct,r+0.3 v. when high, this output indicates the received optical power is below the worst case receiver sensit ivity (as defined by the standard in use). low indicates normal operation. in the low state, the output will be pulled to < 0.8 v. 5. rd-/+: these are the differential receiver outputs. they are ac coupled 100 ? differential lines which should be terminated with 100 ? differential at the user serdes. the ac coupling is done inside the module and is thus not required on the host board. the volt age swing on these lines will be between 250 and 2000 mv differential (160 - 1000 mv single ended) when properly terminated. 6. vccr and vcct are the receiver and transmitter power supplies. they are defined as 3.135 - 3.465 v at the sfp connector pin. the maximum supply current is 250 ma and the associated inrush current will be no more than 30 ma above steady state after 500 nano seconds. 7. td-/+: these are the differential transmitter inputs. they are ac coupled differential lines with 100 ? differential termination inside the module. the ac coupling is done inside the module and is thus not required on the host board. the inputs will accept differenti al swings of 500 - 2400 mv (250 - 1200 mv single ended), though it is recommended that values between 500 and 1200 mv differential (250 - 60 0 mv single ended) be used for best emi performance. table 2. pin description pin name function/description msa notes 1 veet transmitter ground 2 tx fault transmitter fault indication note 1 3 tx disable transmitter disable - module disables on high or open note 2 4 mod-def2 module definition 2 - two wire serial id interface note 3 5 mod-def1 module definition 1 - two wire serial id interface note 3 6 mod-def0 module definition 0 - grounded in module note 3 7 rate select not connected 8 los loss of signal note 4 9 veer receiver ground 10 veer receiver ground 11 veer receiver ground 12 rd- inverse received data out note 5 13 rd+ received data out note 5 14 veer receiver ground 15 vccr receiver power - 3.3 v 5% note 6 16 vcct transmitter power - 3.3 v 5% note 6 17 veet transmitter ground 18 td+ transmitter data in note 7 19 td- inverse transmitter data in note 7 20 veet transmitter ground
8 notes: 1. the ieee organizationally unique identifier (oui) assigned to avago is 00-17-6a (3 bytes of hex). 2. laser wavelength is represented in 16 unsigned bits. 3. addresses 63 and 95 are checksums calculated (per sff-8472 and sff-8074) and stored prior to product shipment. 4. addresses 68-83 specify the ascii serial number and will vary on a per unit basis. 5. addresses 84-91 specify the ascii date code and will vary on a per date code basis. table 3. eeprom serial id memory contents - address a0h byte # decimal data hex notes byte # decimal data hex notes byte # decimal data hex notes 0 03 sfp physical device 27 20 54 20 1 04 sfp function defined by serial id only 28 20 55 20 2 07 lc optical connector 29 20 56 30 300 3020 5730 4 10 sonet reach specifier 31 20 58 30 5 04 sonet compliance code 32 20 59 30 600 3320 60table 4 700 3420 61table 4 800 3520 6200 9 00 36 00 63 checksum for bytes 0-62 3 10 00 37 00 hex byte of vendor oui 1 64 00 11 05 sonet scrambled 38 17 hex byte of vendor oui 1 65 1a hardware sfp tx_disable, tx _ f a u l t & r x _ l o s 12 02 155 mbit/sec nominal bit rate 39 6a hex byte of vendor oui 1 66 00 upper bit rate margin 13 00 40 41 a 67 00 lower bit rate margin 14 28 link length 9 m in km 41 46 f 68-83 vendor specific serial number ascii characters 4 15 ff link length 9 m in m 42 43 c 84-91 vendor date code ascii characters 5 16 00 43 54 t 92 table 4 17 00 44 2d - 93 table 4 18 00 45 35 5 94 table 4 19 00 46 37 7 95 checksum for bytes 64-94 3 20 41 a 47 36 6 96-127 00 vendor specific eeprom 21 56 v 48 table 4 128-255 00 reserved 22 41 a 49 table 4 23 47 g 50 table 4 24 4f o 51 table 4 25 20 52 table 4 26 20 53 20
9 table 4. individual identifiers afct-5760nlz afct-5760npz AFCT-5760ANLZ afct-5760anpz byte # hex notes hex notes hex notes hex notes 48 30 0 30 0 30 0 30 0 49 4e n 4e n 41 a 41 a 50 4c l 50 p 4e n 4e n 51 5a z 5a z 4c l 50 p 52 20 20 5a z 5a z 60 05 1310nm 05 1310nm 05 1310nm 05 1310nm 61 1e 1e 1e 1e 92 00 00 00 00 93 00 00 00 00 94 00 00 00 00 afct-5765nlz afct-5765npz afct-5765anlz afct-5765anpz byte # hex notes hex notes hex notes hex notes 48 35 5 35 5 35 5 35 5 49 4e n 4e n 41 a 41 a 50 4c l 50 p 4e n 4e n 51 5a z 5a z 4c l 50 p 52 20 20 5a z 5a z 60 05 1310nm 05 1310nm 05 1310nm 05 1310nm 61 1e 1e 1e 1e 92 68 68 68 68 93 f0 f0 f0 f0 94 01 01 01 01
10 table 5. eeprom serial id memory contents - address a2h (afct-5765z family only) notes : 1. temperature (temp) is decoded as a 16 bit signed twos compliment integer in increments of 1/256 c. 2. supply voltage (v cc) is decoded as a 16 bit unsigned integer in increments of 100 v. 3. laser bias current (tx bias) is decoded as a 16 bit unsigned integer in increments of 2 a. 4. transmitted average optical power (tx pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 w. 5. received average optical power (rx pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 w. 6. bytes 55-94 are not intended from use with afct-5765xxxx, but have been set to default values per sff-8472. 7. bytes 95 is a checksum calculated (per sff-8472) and stored prior to product shipment. 8. byte 127 accepts a write but performs no action (reserved legacy byte). 9. bytes 128-247 are write enabled (customer writable). 10. byte 255 bits 2 and 3 control laser margining (per table 7) when an enabling password is entered into bytes 123-126. byte # decimal notes byte # decimal notes byte # decimal notes 0temp h alarm msb 1 26 tx pwr l alarm msb 4 104 real time rx p av msb 5 1temp h alarm lsb 1 27 tx pwr l alarm lsb 4 105 real time rx p av lsb 5 2temp l alarm msb 1 28 tx pwr h warning msb 4 106 reserved 3 temp l alarm lsb 1 29 tx pwr h warning lsb 4 107 reserved 4temp h warning msb 1 30 tx pwr l warning msb 4 108 reserved 5temp h warning lsb 1 31 tx pwr l warning lsb 4 109 reserved 6 temp l warning msb 1 32 rx pwr h alarm msb 5 110 status/control - see table 6 7 temp l warning lsb 1 33 rx pwr h alarm lsb 5 111 reserved 8v cc h alarm msb 2 34 rx pwr l alarm msb 5 112 flag bits - see table 7 9v cc h alarm lsb 2 35 rx pwr l alarm lsb 5 113 flag bit - see table 7 10 v cc l alarm msb 2 36 rx pwr h warning msb 5 114 reserved 11 v cc l alarm lsb 2 37 rx pwr h warning lsb 5 115 reserved 12 v cc h warning msb 2 38 rx pwr l warning msb 5 116 flag bits - see table 7 13 v cc h warning lsb 2 39 rx pwr l warning lsb 5 117 flag bits - see table 7 14 v cc l warning msb 2 40-55 reserved 118 reserved 15 v cc l warning lsb 2 56-94 external calibration constants 6 119 reserved 16 tx bias h alarm msb 3 95 checksum for bytes 0-94 7 120-122 reserved 17 tx bias h alarm lsb 3 96 real time temperature msb 1 123 18 tx bias l alarm msb 3 97 real time temperature lsb 1 124 19 tx bias l alarm lsb 3 98 real time vcc msb 2 125 20 tx bias h warning msb 3 99 real time vcc lsb 2 126 21 tx bias h warning lsb 3 100 real time tx bias msb 3 127 reserved 8 22 tx bias l warning msb 3 101 real time tx bias lsb 3 128-247 customer writable 9 23 tx bias l warning lsb 3 102 real time tx power msb 4 248-254 vendor specific 24 tx pwr h alarm msb 4 103 real time tx power lsb 4 255 25 tx pwr h alarm lsb 4
11 table 6. eeprom serial id memory contents - address a2h, byte 110 (afct-5765z family only) notes: 1. bit 6 is logic ord with the sfp tx_disable input pin 3 ... either asserted will disable the sfp transmitter. 2. afct-5765z does not respond to state changes on rate select input pin. it is internally hardwired to full bandwidth. bit # status/control name description 7 tx disable state digital state of sfp tx disable input pin (1 = tx_ disable asserted) 6 soft tx disable read/write bit for changing digital state of sfp tx_disable function 1 5reserved 4 rx rate select state digital state of sfp rate select input pin (1 = full bandwidth of 155 mbit) 2 3reserved 2 tx fault state digital state of the sfp tx fault output pin (1 = tx fault asserted) 1 rx los state digital state of the sf p los output pin (1 = los asserted) 0 data ready (bar) indicates transceiver is powered and real time sense data is ready (0 = ready) table 7. eeprom serial id memory contents - address a2h, bytes 112, 113, 116, 117 (afct-5765z family only) byte bit # flag bit name description 112 7 temp high alarm set when transceiver nternal temperature exceeds high alarm threshold. 6 temp low alarm set when transceiver internal temperature exceeds alarm threshold. 5v cc high alarm set when transceiver internal supply voltage exceeds high alarm threshold. 4v cc low alarm set when transceiver internal supply voltage exceeds low alarm threshold. 3 tx bias high alarm set when transceiver laser bias current exceeds high alarm threshold. 2 tx bias low alarm set when transceiver laser bias current exceeds low alarm threshold. 1 tx power high alarm set when transmitted average optical power exceeds high alarm threshold. 0 tx power low alarm set when transmitted average optical power exceeds low alarm threshold. 113 7 rx power high alarm set when received p_avg optical power exceeds high alarm threshold. 6 rx power low alarm set when received p_avg optical power exceeds low alarm threshold. 0-5 reserved 116 7 temp high warning set when transceiver internal temperature exceeds high warning threshold. 6 temp low warning set when transceiver internal temperature exceeds low warning threshold. 5v cc high warning set when transceiver internal supply voltage exceeds high warning threshold. 4v cc low warning set when transceiver internal supply voltage exceeds low warning threshold. 3 tx bias high warning set when transceiver laser bias current exceeds high warning threshold. 2 tx bias low warning set when transceiver laser bias current exceeds low warning threshold. 1 tx power high warning set when transmitted average optical power exceeds high warning threshold. 0 tx power low warning set when transmitted average optical power exceeds low warning threshold. 117 7 rx power high warning set when received p_avg optical power exceeds high warning threshold. 9 rx power low warning set when received p_avg optical power exceeds low warning threshold. 0-5 reserved
12 optical parameters absolute maximum ratings absolute maximum ratings are those values beyond which functional performance is not intended, device reliability is not implied, and damage to the device may occur. notes: 1. msa gives max current at 300 ma. 2. msa filter is required on host board 10 hz to 2 mhz. 3. lvttl, external 4.7-10 k ? pull up resistor required on host board to voltage less than vcc + 0.3 v. 4. internally ac coupled and terminated (100 ? differential). 5. internally ac coupled and load termination located at the user serdes. 6. minimum input to mod-def1,2 is 0.7*v cc transceiver electrical characteristics for multirate operations at fast ethernet (125 mbit/s) and oc-3 (155 mbit/s) *6 recommended multirate operating conditions typical operating conditions are those values for which functional performance and device reliability is implied. parameter symbol minimum maximum unit notes storage temperature (non-operating) t s -40 +85 c relative humidity rh 0 85 % supply voltage v cc -0.5 3.63 v input voltage on any pin v i -0.5 v cc v receiver optical input p in abs 0 dbm parameter symbol minimum typical maximum unit notes case operating temperature afct-576xnlz/npz afct-576xanlz/anpz t c t c -10 -40 +85 +85 c c supply voltage v cc 3.1 3.3 3.5 v parameter symbol minimum typical maximum unit notes module supply current i cct 250 ma 1 power dissipation p diss 875 mw ac electrical characteristics power supply noise rejection psnr 100 mv 2 in-rush current 30 ma dc electrical characteristics signal outputs: transmit fault (tx_fault) loss of signal (los) v oh 2.0 3.5 v 3 v ol 00.8v signal inputs: transmitter disable (tx_disable) mod-def1, 2 v ih 2.0 3.5 v 6 v il 00.8v data input: transmitter single ended input voltage (td) v i 250 1200 mv 4 data ouput: receiver single ended output voltage (rd) v o 250 1000 mv 5
13 receiver optical characteristics for multirate operations at fast ethernet (125 mbit/s) and oc-3 (155 mbit/s) notes: 1. the receiver is guaranteed to provide output data with a bit error rate better than or equal to 1 x 10 -10 measured with tx powered and carrying data. parameter symbol minimum typical maximum unit notes receiver sensitivity p in min -34 dbm 1 receiver overload p in max 0 dbm input operatin g wavelen g th 1261 1360 nm los deassert p losd -34.5 dbm los assert p losa -45 dbm los hysteresis p h 0.5 4 db transmitter optical characteristics for multirate operations at fast ethernet (125 mbit/s) and oc-3 (155 mbit/s) *typicals indicated expected values for room temperature measurements +25 c notes: 1. the output power is coupled into a 1 m single mode fiber. minimum output optical level is at end of life 2. the relationship between fwhm and rms values for spectral width can derived from the gaussian shaped spectrum which results i n rms=fwhm/2.35 3. these are unfiltered 20-80% values. 4. 30% margin to eye mask in telcordia gr-253-core and itu-t g.957 5. jitter measurements taken with avago omniber 718 in accordance with gr253 parameter symbol minimum typical* maximum unit notes optical output power p out -5 0 dbm 1 center wavelen g th c 1270 1360 nm s pectral width - rms 3nm2 optical rise time t r 2.5 ns 3 optical fall time t f 2.5 ns 3 tx disable off power p off -45 dbm extinction ratio er 10 db eye mask mar g in emm 30 % 4 jitter generation pk to pk 70 mui 5 rms 7 mui 5
14 notes: 1. temperature was measured internal to the transceiver. valid from = -10 c to +85 c or from -40c to +85c. for calibration to an external temperature, please contact avago technologies. 2. reference voltage is 3.3 v. 3. valid from 0 to 50 ma, avg. transceiver digital diagnostic monitor (real time sense) characteristics (afct-5765z family only) parameter symbol min. typ. max. unit reference transceiver internal temperature accuracy t int -3.0 +3.0 c 1 transceiver internal supply volta g e accuracy v int -3.0 +3.0 % 2 transmitter laser dc bias current accuracy i int -10 +10 % 3 transmitted avera g e optical output power accuracy p t -3.0 +3.0 db received avera g e optical input power accuracy p r -3.0 +3.0 db notes: 1. time from rising edge of tx_disable to when the optical output falls below 10% of nominal. 2. time from falling edge of tx_disable to when the modulated optical output rises above 90% of nominal. 3. time from power on or falling edge of tx_disable to when the modulated optical output rises above 90% of nominal. 4. from power on or negation of tx_fault using tx_disable. 5. time tx_disable must be held high to reset the laser fault shutdown circuitry. 6. time from loss of optical signal to rx_los assertion. 7. time from valid optical signal to rx_los de-assertion. 8. time from two-wire interface assertion of tx_disable (a2h, byte 110, bit 6) to when the optical output falls below 10% of nom inal. measured from falling clock edge after stop bit of write transaction. 9. time from two-wire interface de-assertion of tx_disable (a2h, byte 110, bit 6) to when the modulated optical output rises abo ve 90% of nominal. 10. time from fault to two-wire interface tx_fault (a2h, byte 110, bit 2) asserted. 11. time for two-wire interface assertion of rx_los (a2h, byte 110, bit 1) from loss of optical signal. 12. time for two-wire interface de-assertion of rx_los (a2h, byte 110, bit 1) from presence of valid optical signal. 13. from power on to data ready bit asserted (a2h, byte 110, bit 0). data ready indicates analog monitoring circuitry is functio nal. 14. time from power on until module is ready for data transmission over the serial bus (reads or writes over a0h and a2h). 15. time from stop bit to completion of a 1-8 byte write command. parameter symbol minimum maximum unit notes hardware tx_disable assert time t_off 10 s note 1 hardware tx_disable negate time t_on 1 ms note 2 time to initialize, including reset of tx_fault t_init 300 ms note 3 hardware tx_fault assert time t_fault 100 s note 4 hardware tx_disable to reset t_reset 10 s note 5 hardware rx_los assert time t_loss_on 100 s note 6 hardware rx_los de-assert time t_loss_off 100 s note 7 software tx_disable assert time t_off_soft 100 ms note 8 software tx_disable negate time t_on_soft 100 ms note 9 software tx_fault assert time t_fault_soft 100 ms note 10 software rx_los assert time t_loss_on_soft 100 ms note 11 software rx_los de-assert time t_loss_off_soft 100 ms note 12 analog parameter data ready t_data 1000 ms note 13 serial bus hardware ready t_serial 300 ms note 14 write cycle time t_write 10 ms note 15 serial id clock rate f_serial_clock 400 khz transceiver timing characteristics
15 tx_fault v cc > 3.15 v t_init tx_disable transmitted signal t_init tx_fault v cc > 3.15 v tx_disable transmitted signal t-init: tx disable negated t-init: tx disable asserted tx_fault v cc > 3.15 v t_init tx_disable transmitted signal t_off tx_fault tx_disable transmitted signal t-init: tx disable negated, module hot plugged t-off & t-on: tx disable asserted then negated insertion t_on tx_fault occurance of fault t_fault tx_disable transmitted signal tx_fault occurance of fault tx_disable transmitted signal t-fault: tx fault asserted, tx signal not recovered t-reset: tx disable asserted then negated, tx signal recovered t_reset t_init* * cannot read input... tx_fault occurance of fault t_fault tx_disable transmitted signal optical signal los t-fault: tx disable asserted then negated, tx signal not recovered t-loss-on & t-loss-off t_loss_on t_init* t_reset * sfp shall clear tx_fault in t_init if the failure is transient t_loss_off occurance of loss figure 5. timing diagrams
16 notes: 1. bail delatch is colored blue for sonet/single-mode identification. avago afct-576xz ### nm laser prod 21cfr(j) class 1 country of origin yyww ###### figure 6. module drawing
17 figure 7. assembly drawing
figure 8. sfp host board mechnical layout
for product information and a complete list of distributors, please go to our web site: www.avagotech.com avago, avago technologies, and the a logo are trademarks of avago technologies limited in the united states and other countries . data subject to change. copyright ? 2007 avago technologies, limited. all rights reserved. obsoletes av01-0519en av02-0140en - february 23, 2007 ordering information please contact your local field sales engineer or one of avago technologies franchised distributors for ordering information. for technical information, please visit avago technologies web-page at www.avagotech.com or contact one of avago technologies regional technical response centers. for information related to sff committee documentation, visit www.sffcommittee.org . 1300nm fp laser (operating case temperature -10 to +85 c) with dmi afct-5765nlz standard de-latch afct-5765npz bail de-latch without dmi afct-5760nlz standard de-latch afct-5760npz bail de-latch 1300nm fp laser (operating case temperature -40 to +85 c) with dmi afct-5765anlz standard de-latch afct-5765anpz bail de-latch without dmi AFCT-5760ANLZ standard de-latch afct-5760anpz bail de-latch eeprom content and / or label options afct-5760xxxx-yyy afct-5765xxxx-yyy where xxxx refers to product option yyy is customer specific

▲Up To Search▲

Price & Availability of AFCT-5760ANLZ

	To Download AFCT-5760ANLZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .