do not scale from this print "b" ref .745 ref 18.9 .010 ref 0.3 .055 1.40 2 max sway (typ) "a" "a" -lc: locking clip option shown t-1g1-xx-x qth-30-xx-d-xx fig. 1 cqth-090-01-x-d-lc shown lc-08-tm-01 obsolete (no of positions / 30) x .7875[20.003] .788 ref 20.0 .155 ref 3.9 .235 5.97 ref .008 ref 0.2 .644 ref 16.4 29 eq spaces @ .0197[.500] .047 ref 1.19 c3 02 01 cqth-xxx-xx-x-d-xx no of positions -030, -060, -090, -120, -150 (per row) row specification -d: double (use qth-30-xx-d-xx & qthh-30-xx-d-xx) option -lc: locking clips (use lc-08-tm-01) -a: alignment pins (use qth-30-xx-d-xx-a for -01 & -02) (for -03 thru -10 see table 4) plating specification -c: electro-polished selective (use t-1sxx-xx-c & t-1gxx-xx-g) lead style -01: .1680[4.267] -02: .2861[7.264] -03: .4043[10.269] -04: .6001[15.246] -05: .7181[18.240] -06: .8361[21.237] -07: .9542[24.237] -08: 1.1511[29.238] -09: .5224[13.269] = see table 4 "a" .038 ref 1.0 .098 ref 2.49 .015 ref 0.4 .037 ref 0.9 .280 ref 7.11 section "a"-"a" c1 c2 .003[.08] .002[.03] (see note 5 & 7) t-1sxx-xx-x (see table 1) (see note 9) see table 2 ((no of positions / 30) x .7875[20.003]) - .060[1.52] ref -a: alignment pin option qth-30-xx-d-xx-a [style -01 & -02] .035 0.89 ref .037 0.95 ref .038 ref 1.0 r c (see note 7) sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01[.3] 2 .xxx: .005[.13] .xxxx: .0020[.051] material: .5mm double row hs terminal assembly by: cqth-xxx-xx-x-d-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing b. cooper 10/5/2007 3 1 sheet scale: 1.75:1 insulator: lcp, color: black terminal & ground plane: phos bronze f:\dwg\misc\mktg\cqth-xxx-xx-x-d-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. minimum pushout force: 6 oz for C01 & -02, 8 oz for C03 thru C10. 3. minimum ground plane retention: 1 lb. 4. parts to be molded to position. 5. maximum variance of .002[.05]. applies to signal or grounds independent of the ground or signal pins respectively. 6. lead styles -03 thru -9: top body (qth) cannot have -a option. 7. ground plane press height must be .003 [.07] less than the maximum height or .002[.03] greater than the minimum height of signal pin. 8. t-1r36 retention to body to be 1.0 lbf. 9. cut off burr not to exceed .003 in any direction, burr plus tab height not to exceed .006. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision b
.035 ref 0.89 (no of positions / 30) x .7875[20.003] - .060[1.52] ref -a: alignment pin option (cqth-090-05-x-d-a shown) [different as shown, otherwise same as fig. 1] (styles -03 thru -09, see table 4) fig. 2 qthh-30-xx-d-xx-a qth-30-02-d-xx (see note 6) .038 1.0 ref .053 1.3 ref sheet of .5mm double row hs terminal assembly by: cqth-xxx-xx-x-d-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing b. cooper 10/5/2007 3 2 sheet scale: 1.75:1 revision b f:\dwg\misc\mktg\cqth-xxx-xx-x-d-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
.278 ref 7.07 .055 1.40 .010 ref 0.25 .118 ref 3.00 2 max sway (typ) "b" "b" (cqth-090-03-x-d-lc shown) [different as shown, otherwise same as fig. 1] fig. 3 t-1g1-xx-x qthh-30-01-d-xx qth-30-02-d-xx (see note 6) .265 ref 6.73 (see notes 5 & 7) "c" .281 ref 7.14 .037 ref 0.94 .053 ref 1.33 'e' section "b"-"b" t-1s60-xx-x +.003[.08] -.001[.03] (see note 7) (see note 9) see table 2 .432 10.97 ref "c" "c" fig. 4 (cqth-090-05-x-d shown) [different as shown, otherwise same as fig. 2] qthh-30-03-d-xx .600 15.24 ref "d" "d" fig. 5 (cqth-090-07-x-d shown) [different as shown, otherwise same as fig. 2] qthh-030-04-d-xx [see notes 5 & 7] "c" (see table 4) section "c"-"c" scale 1.25 : 1 t-1s60-xx-x t-1g1-xx-x .003[.08] .001[.03] (see note 7) c4 (see note 9) see table 2 [see notes 5 & 7] "c" (see table 4) section "d"-"d" scale 1.25 : 1 t-1s61-xx-x t-1g17-xx-x .003[.08] .001[.03] (see note 7) c5 c6 (see note 9) see table 2 .003 max tab height 0.08 .006 max burr 0.15 + tab height detail 'e' scale 8 : 1 sheet of .5mm double row hs terminal assembly by: cqth-xxx-xx-x-d-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing b. cooper 10/5/2007 3 3 sheet scale: 1.75:1 revision b f:\dwg\misc\mktg\cqth-xxx-xx-x-d-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|
