1 ftr-k1 series ftr-k1 series power relay 1 pole - 16a sealed type (a) relay type ftr-k1: ftr-k1 series (b) contact confguration a : 1 form a c : 1 form c (c) coil type k : standard type (400mw) (d) coil rated voltage 005 : 5.....48 vdc coil rating table at page 3 (e) contact material w : agsno 2 (f) special type kw : sealed type, rtiii actual marking does not carry the type name : "ftr" e.g.: ordering code: ftr-k1ck005w-kw actual marking: k1ck005w-kw n partnumber information ftr-k1 c k 005 w - kw [example] (a) (b) (c) (d) (e) (f) n features l 1 pole l 16a l 1 form a / 1 form c l coil sensitive 400mw l high insulation in small package (between coil and contacts) - insulation distance: 10mm min. - dielectric strength: 5,000vac - surge strength: 10,000v l conform to ul1446 class f coil insulation system l cadmium free contacts l sealed type, rtiii l rohs compliant please see page 7 for more information
2 ftr-k1 series ftr-k1 series n specification item ftr-k1 ck ( ) w-kw ftr-k1 ak ( ) w-kw contact data confguration 1 form c 1 form a construction single material agsno 2 resistance (initial) max. 100mohm at 1a, 6vdc contact rating (resistive) 16a, 250vac max. carrying current * 1 20a max. switching voltage 440vac max. switching power 4,000va min. switching load * 2 100ma, 5vdc life mechanical min. 20 x 10 6 operations electrical rating resistive load min. 10 x 10 3 operations min. 20 x 10 3 operations coil data rated power (20 c) 400 / 430 mw operating temperature range -40 c to +105 c (no frost) timing data operate (at nominal voltage) max. 15ms (without bounce, no diode) release (at nominal voltage) max. 5ms (without bounce, no diode) insulation resistance (initial) min. 1,000mohm at 500vdc dielectric strength open contacts 1,000vac (50/60hz) 1min contacts to coil 5,000vac (50/60hz) 1min surge strength coil to contacts 10,000v / 1.2 x 50s standard wave clearance 10mm creepage 10mm en61810-1, vde0435 voltage 250 pollution degree 3 material group iii a category c / 250v other vibration resistance misoperation1us 10 to 55hz double amplitude 0.7mm endurance 10 to 55hz double amplitude 1.5mm shock misoperation1us 100m/s2 (11 1ms) endurance 1,000m/s2 (6 1ms) weight approximately 13g sealing rtiii * 1: need to consider the heat from pcb when max. current is more than 10a. * 2: minimum switching loads mentioned above are reference values. please perform the confrmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 16a type
3 ftr-k1 series ftr-k1 series n coil rating coil code rated coil voltage (vdc) coil resistance +/- 10% (ohm) must operate voltage (vdc) * must release - voltage (vdc) * max. coil voltage (vdc) rated power (mw) 005 5 62 3.5 0.5 12.2 400 006 6 90 4.2 0.6 14.7 009 9 202 6.3 0.9 22.0 012 12 360 8.4 1.2 29.4 018 18 810 12.6 1.8 44.1 022 22 1210 15.4 2.2 53.9 024 24 1440 16.8 2.4 58.8 028 28 1960 19.6 2.8 68.6 048 48 5360 33.6 4.8 117.6 430 note: all values in the table are valid for 20c and zero contact current. * specifed operate values are valid for pulse wave voltage. type compliance contact rating ul 508 e 63614 flammability: ul 94-v0 (plastics) vde 0435; 40013848 16a, 250vac cos =1 85 c 10.000 ops. (1 form a type) n safety standards
4 ftr-k1 series ftr-k1 series n characteristic data
5 ftr-k1 series ftr-k1 series
6 ftr-k1 series ftr-k1 series n dimensions l dimensions l drilling plan (bottom view) l wiring diagram (bottom view) unit: mm note: in case of 1 form a, there is no "stationary" contact arm.
7 ftr-k1 series ftr-k1 series 1. general information l all signal and power relays produced by fujitsu components are compliant with rohs directive 2002/95ec including amendments. l cadmium as used in electrical contacts is exempted from the rohs directives on october 21st, 2005. (amendment to directive 2002/95/ec) l all of our signal and power relays are lead-free. please refer to lead-free status info for older date codes at: http://www.fujitsu.com/us/downloads/micro/fcai/relays/lead-free-letter.pdf l lead free solder plating on relay terminals is sn-3.0ag-0.5cu, unless otherwise specifed. this material has been verifed to be compatible with pbsn assembly process. 2. recommended lead free solder profle l recommended solder sn-3.0ag-0.5cu. rohs compliance and lead free information 3. moisture sensitivity l moisture sensitivity level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. tin whiskers l dipped snagcu solder is known as presenting a low risk to tin whisker development. no considerable length whisker was found by our in house test. we highly recommend that you confrm your actual solder conditions flow solder condition: pre-heating: maximum 120?c soldering: dip within 5 sec. at 260?c solder bath solder by soldering iron: soldering iron temperature: maximum 360?c duration: maximum 3 sec.
8 ftr-k1 series japan fujitsu component limited gotanda-chuo building 3-5, higashigotanda 2-chome, shinagawa-ku tokyo 141, japan tel: (81-3) 5449-7010 fax: (81-3) 5449-2626 email: promothq@ft.ed.fujitsu.com web: www.fcl.fujitsu.com north and south america fujitsu components america, inc. 250 e. caribbean drive sunnyvale, ca 94089 u.s.a. tel: (1-408) 745-4900 fax: (1-408) 745-4970 email: components@us.fujitsu.com web: http://us.fujitsu.com/components europe fujitsu components europe b.v. diamantlaan 25 2132 wv hoofddorp netherlands tel: (31-23) 5560910 fax: (31-23) 5560950 email: info@fceu.fujitsu.com web: emea.fujitsu.com/components/ asia pacifc fujitsu components asia ltd. 102e pasir panjang road #01-01 citilink warehouse complex singapore 118529 tel: (65) 6375-8560 fax: (65) 6273-3021 email: fcal@fcal.fujitsu.com web: http://www.fujitsu.com/sg/services/micro/components/ fujitsu components international headquarter offces ?2010 fujitsu components europe b.v. all rights reserved. all trademarks or registered trademarks are the property of their respective owners. the contents, data and information in this datasheet are provided by fujitsu component ltd. as a service only to its user and only for gen - eral information purposes. the use of the contents, data and information provided in this datasheet is at the users own risk. fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehen - sive, complete and up to date. fujitsu components europe b.v. and affliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. nor do fujitsu components europe b.v. and affliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or ftness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. rev. august 12 2010 ftr-k1 series
|
