View SCP9FB8-GL-CN-F480_6658313.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

- 1 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 technical specification for small form factor pluggable (sfp) scp9fb8-gl-cn-xxxx (diagnostic monitoring with internal calibration) # safety precaution symbols this specification uses various picture symbols to prevent possible injury to operator or other persons or damage to properties for appropriate use of the product. the symbols and definitions are as shown below. be sure to be familiar with these symbols before reading this specification. warning wrong operation without following this instruction may lead to human death or serious injury. caution wrong operation without following this instruction may lead to human injury or property damage. example of picture symbols indicates prohibition of actions. action details are explained thereafter. indicates compulsory actions or instructions. action details are explained thereafter. 155.52mbps 622.08mbps other ____________ short haul long haul intermediate reach long reach single 5.0 v single 3.3 v other ____________ 1.3 m 1.55 m other ____________ other ____________ w / diagnostic monitor w /o diagnostic monitor sumitomo electric reserves the right to make changes in this specification without prior notice. sumitomo electric industries, ltd. and excelight communications, inc., have been granted license to the following patents under a license agreement with finisar corporation: us 5,019,769, us 6,439,918 b1 dwdm (apd) up to 2.7gbps multi rate 3200ps/nm
- 2 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 caution do not disassemble this product. otherwise, failure, electrical shock, overheating or fire may occur. figure 1. block diagram 1. general features and applications of scp9fb8-gl-cn-xxxx are listed below. features * rohs 6/6 compliant * c-band dwdm transceivers * cooled dwdm dfb laser transmitter * compliant with sfp msa. * sff-8472 rev.9.3 compliant diagnostic monitoring implemented. * dwdm sfp rev1.0 variable decision threshold control implemented. * multiple bit rate operation 622.08mbps to 2.7gbps * power supply voltage single 3.3v * compact package size 56.5 x 13.7 x 8.6mm * electrical interface ac coupled for data, lvttl for tx disable and open collector output for los and tx fault. circuit ground is internally isolated from frame ground. * fiber coupled power 0 to +4dbm * input power range -28 to -9dbm * link budget 28db * dispersion penalty max. 3.5db (3200ps/nm) applications * switch to switch interface * switch backbone applications * high speed interface for file server 2. block diagram rd+ rd- lo s po st a mp . 15 0 ? 4 ? mod -def (0) mod - def (1) mod - def (2) 4. 7k t o 10 k ? host board td+ td- 4. 7k ? 4 ? - k ? 4 - tx disable tx fault ? 4 sfp module (a) transmitter (b) receiver (c) eeprom 10 0 ? host_vcc tec co ntrola r tec ap d dc-dc conve rte r thermister diagnostic moni to r 15 0 ?
- 3 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 3. package dimensions all dimensions are in mm. figure 2. outline dimensions * recommended cage and connector -top emi cage 1367035-1( tyco/electronics:1308292--amp-04/00 ) -bottom emi cage 1367034-1( tyco/electronics:1308292--amp-04/00 ) -host connector 1367073-1( tyco/electronics:1308292--amp-04/00 ) please refer to their latest specifications. notes: 1.unit;mm *bail material: stainless steel
- 4 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 figure 3. diagram of host board connector block pin numbers and names 4. pin assignment veet veet veer veer td- td+ rd+ rd- vcct vccr veet veer txfault mod-def(2) mod-def(1) mod-def(0) nuc los 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 towards asic towards bezel tx disable veer plug seq.: pin engagement sequence during hot plugging. pin num . name function plug seq. not e s 1 veet trans mitter ground 1 2 tx fault trans mitter fault 3 indication note 1 note 2 module disables on high or open 4 mod-def2 module definition 2 3 note 3, 2 w ire serial id and interf ace 5 mod-def1 module definition 1 3 note 3, 2 w ire serial id and interf ace 6 mod-def0 module definition 0 3 note 3 grounded internally via r (tbd) nuc no user connection, reserved for future function. 8 los loss of signal 3 note 4 9 veer receiver ground 1 10 veer receiver ground 1 11 veer receiver ground 1 12 rd- inv. receiver data out 3 note 5 13 rd+ receiver data out 3 note 5 14 veer receiver ground 1 15 vcc r receiver pow er 2 3.3v 5% 16 vcc t trans mitter pow er 2 3.3v 5% 17 veet trans mitter ground 1 18 td+ trans mitter data in 3 note 6 19 td- inv. transmitter data in 3 note 6 20 veet trans mitter ground 1 3 7nuc 3 3 tx dis able trans mitter disable
- 5 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 figure 4. sfp host board mechanical layout note 1) tx fault is an open collector output that shall be pulled up with a 4.7k - 10k ? resistor on the host board. pull up voltage between 2.4v and vcct v. when high, output indicates a laser fault of some kind. low indicates normal operation. tx fault is asserted when a) bias current of laser, b) ld temperature exceed the factory-calibrated threshold level. 2) tx disable is an input that is used to shut down the transmitter optical output. it is pulled up within the module with a 4.7k ? resistor. 3) mod-def 0,1,2. these are the module definition pins. they should be pulled up with a 4.7k - 10k ? resistor on the host board. the pull-up voltage shall be vcct. mod-def 0 indicates that the module is present mod-def 1 is the clock line of two wire serial interface for serial id mod-def 2 is the data line of two wire serial interface for serial id 4) los (loss of signal) is an open collector output that shall be pulled up with a 4.7k - 10k ? resistor. pull up voltage between 2.4v and vccr v. low indicates normal operation. 5) rd-/+: these are the differential receiver outputs. they are ac coupled 100 ? differential lines which should be terminated with 100 ? (differential) at the user serdes. the ac coupling is done inside the module and is thus not required on the host board. 6) td-/+: these are the differential transmitter inputs. they are ac-coupled, differential lines with 100 ? differen- tial termination inside the module. the ac coupling is done inside the module and is thus not required on the host board.
- 6 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 pin 11 pin 10 pin 20 pin 1 figure 5. sfp host board mechanical layout (cont.) figure 6. recommended bezel design
- 7 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 5. absolute maximum ratings warning use the product with the rated voltage described in the specification. if the voltage exceeds the maximum rating, overheating o r fire may occur. 6. electrical interface ( unless otherwise specified, vcct,r = 3.135 to 3.465 v and all operating temperature shall apply. ) 6-1. operating characteristics 6-3. receiver side 6-2. transmitter side figure 7. definition of differential input / output voltage swing bias voltage input / output voltage swing (vswing) differential input / o utput voltage swing (vin / vout) = 2 x vswing symbol min. typ. max. unit note differential input voltage sw ing (td+,td-) vin 0.5 1.6 vp-p 1 input differential impedance zin 80 100 120 ? tx fault fault vf aulth 2.4 vcct v 2 normal vf aultl 0 0.6 v 2, 3 tx disable disable vdi 2.0 vcct+0.3 v enable vei 0 0.8 v notes 1. refer to figure 7. 2. tx fault is pulled up to vcct w ith a 4.7k-10k ? resistor on the host board. when high, output indicates a laser fault of some kind. low indicates normal operation. 3. sink current : 1ma 4 . tx disable input is internally terminated to vcct via 4.7 k ? resistor. if pin3 is left open, tx is disable. pa r a me t e r 4 parameter symbol min. ty p. max . unit note output dif feretial impedance rout 80 100 120 ? dif ferential output voltage sw ing (rd+,rd-) vout 0.37 2.0 vp-p 1 los high vloh 2.4 vcc r v 2 output voltage low vlol 0 0.6 v 2, 3 data rise / fall time tr / tf 175 ps 4 notes 1. vcc=+3.3v+/-5%, output load res is tanc e rdif=100 ? . ref er to fi g ure1- ( b ) . ref er to fi g ure7. about def inition of dif ferential sw in g . 2. los is pulled up to vccr w ith a 4.7k-10k ? resistor on the hos t board. low indic ates normal operation. 3. sink current : 1ma 4. 20 to 80%, 2488.32mbps, prbs 2^23-1, nrz, 50% dut y c y cle data. parameter symbol min. ty p. max . unit note storage ambient temperature ts -40 - 85 c 1 operating case temperature tc -5 - 70 c operating relative humidity h a 085% optical input level pin 5 dbm supply voltage vcc t,r -0.3 - 4.0 v input voltage vi 0 - vcc t,r+0.3 v 2 dif ferential input voltage sw ing (td+,td-) vin 2.5 vp-p notes 1. no condensation allowed. 2: for mode-def (1:2) and tx_disable caution do not store the product in the area where temperature exceeds the maximum rating, where there is too much moisture or dampness, where there is acid gas or corrosive gas, or other extreme conditions. otherwise, failure, overheating or fire may occur. sy mbo l min. ty p. max . unit note supply voltage vcc t,r 3.135 3.30 3.465 v supply current icc - - 375 ma 1 icc' - - 415 ma 2 note 1. 2488.32mbps, prbs2^23-1, nrz, 50% duty c ycle data. 2. narrow current spikes due to capacitor charging is ex cluded pa r a me t e r inrush current
- 8 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 7. optical interface 6-4. module definition parameter symbol min. ty p. max . unit note mod_def( 1:2) high v ih 2.0 v cc t+0.3 v input voltage low vil 0 0.8 v mod_def( 2) high v oh 2.4 v cc t v 1 output voltage low vol1 0 0.6 v 1, 2 notes 1. they shall be pulled up to vcct with a 4.7k - 10k ? resistor on the host board. 2. sink current : 3ma 1 7-1. transmitter side figure 8. eye diagram mask for optical output warning do not look at the laser beam projection area (e.g. end of optical connector) with naked eyes or through optical equipment while the power is supplied to this product. otherwise, your eyes may be injured. 1.25 1.00 0.75 0.25 0 -0.25 0.20 ui time (ui) 0 1.0 normalized amplitude logic " 1 " logic " 0 " ( itu-t g.957 ) parameter symbol min. typ max. units notes bit rate range - 622.08 - 2666.06 mbps center wavelength - nm average output power (enable) po 0 - 4 dbm average output power (disable) pdis - - -45 dbm extinction ratio er 8.2 - - db spectral width ? --0.3nm2 side mode suppression ratio smsr 30 - - db 1 eye mask for optical output tjpkt - - 0.07 uipp tjrms 0.007 uirms wavelength stability ? c -100 - 100 pm 1, 4 wavelength deviation from grit at turn on ? c-on -400 - 400 pm 1, 5 notes 1. measured at prbs 2 23 -1, 50% duty cycle, nrz. 2. rbw 0.01nm. 3. for the jitter measurements, the device was driven with sonet oc-48 data pattern with 2 23 -1 prbs payload. measured with a bandpass filter having a high-pass cutoff frequency of 12k hz and a low-pass frequency of 20mhz. 4. after the wavelength is stabilized to the specified channel. c-band (see section 17) 5. the laser transmitter will not be turned on until its temperature is adjusted to ensure operation within ? c-on. this temperature stabilization will occur within t_startup (refer to section 7.4) compliant with telecordia gr-253 core and itu-t g957 transmitter jitter 3 1
- 9 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 parameter symbol min. typ max. units notes dispersion pow er penalty dp - - 3.5 db 1, 2, 3 osnr @0.1nm bw, b2b - 18 - - db 1, 2, 4 dispersion osnr penalty np - - 3.5 db 1, 2, 4, 5 not es 1. ber=10^-12 2. measured at prbs 2 23 -1, 50% duty cycle, nrz. 3. pow er penalty betw een b2b and 3200ps/nm, osnr=21db @ 0.1nm bw. 4. optical input pow er of -22 to -9dbm. 5. osnr penalty betw een b2b at and 3200ps /nm at the optic al input pow er of -22dbm 7-3 transmisson characteristics. 7-2. receiver side parameter symbol min. typ max units notes bit rate range - 622.08 - 2666.06 mbps center wavelength - 1290 - 1610 nm minimum sensitivity (eol) pmin - - -28.0 dbm 1,2 overload pmax -9.0 - - dbm 1,2 los activation level p l a -45.0 - -28.3 dbm los deactivation level p l d -44.7 - -28.0 dbm los hysteresis phys 0.3 - 6.0 db optical reflectance refr - - -27.0 db no t e s 1. ber = 10^-12 2. worst case extinction ratio. measured at prbs 2 23 -1 test pattern, nrz, eol 2
- 10 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 7-4. transceiver timing characteristics parameter symbol min. typ. max. unit note tx disable assert time t_off 20 ms 1 tx disable negate time t_on 20 ms 2 start up time t_startup 15 s 3 time to initialize t_init 300 ms tx fault assert time t_fault 50 ms 4 tx disable to reset t_reset 10 - us 5 los assert time t_loss_on 2.3 100 us 6 los deassert time t_loss_off 100 us 7 serial id clock rate f_serial_clock 100 khz 1. time from rising edge of tx disable to when the optical output falls below 10% of nominal. 2. time from falling edge of tx disable to when the modulated optical output rises above 90% of nominal. 3. from power on. vcc > 3. 15v tx_fault tx_disable transmitted signal t_init t_init t_startup t_startup start up start up normal normal vcc > 3. 15v tx_fault tx_disable transmitted signal t_init t_init t_startup t_startup start up start up normal normal vcc > 3. 15v tx_fault tx_disable transmitted signal t_init t_init t_startup t_startup start up start up normal normal t_on t_on vcc > 3. 15v tx_fault tx_disable transmitted signal t_init t_init t_startup t_startup start up start up normal normal t_on t_on fig9-2. power o n initializat ion of sfp, tx _disable negat ed fig9-3. power o n initializat ion of sfp, tx _disable assert ed fig9-1. tx_disable timing during normal operation 4. time from fault to tx fault on. fig9-4. detec tion of transmitter safety fault condition 5. time tx disable must be held high to reset tx_fault. fig9-6. successful recovery from transient safety fault condition fig9-5. unsuccessful recovery from safety fault condition t_init t_init 6. time from los state to rx los assert. 7. time from non-los state to rx los deassert. fig9-7 timing of los detection
- 11 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 7-5. tx_ fault and tx_shutdown behavior tx _ fault tx _ disable ( lo w ) transmitted signal occurrence of fault tx _ fault tx _ disable ( lo w ) transmitted signal occurrence of fault 8. digital diagnostic memory map figure 11. digital diagnostic memory map the transceiver will automatically swich off the laser under wavelength deviation +/-200pm from grid. fig10-1. tx shutdown behavior on tx_fault assertion by bias current. fig10-2. tx shutdown behavior on tx_fault assertion by ld temperature.
- 12 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 9. eeprom serial id memory contents the data can be read using the 2-wire serial cmos eeprom protocol of the atmel at24c01a or equivalent. note1. 16-bit interper representation value in nm with byte 60 as high byte. use 00 for fe the dw dm wavelength frac tion is : fraction= (byte62)* 0.01nm the final form ula of the laser wavelength: (byte60, 61) + (byte62)*0.01nm note2. address 63 is c heck sum of byte0-62. note3. address 68-83 is vendor serial num ber. note4. address 84-91 is date code. note5. refer to section 10.(enhanced monitoring function) note6. refer to sec tion11. address name of field hex ascii descri p tion address name of field hex ascii descri p tion 0 identifier 0b dwdm sfp 64 00 1 ext. identifier 24 65 1a 2 connector 07 lc connector 66 br max 00 300 67br min00 4 0c 00001100 68 500 69 600 70 700 71 800 71 901fc sin g le mode 73 10 05 fc s p eed 100m&200m 74 11 encodin g 05 sonet scrambled 75 12 br, nominal 19 2488.32mb p s76 13 00 77 14 a0 160km 78 15 max case tem p 46 +70c 79 16 min case tem p fb -5c 80 17 max su pp l y current 5e units of 4ma ( 376ma ) 81 18 reserved 00 82 19 chan s p acin g and tuni n 41 83 20 vendor name 53 s 84 21 75 u 85 22 6d m 86 23 69 i 87 24 74 t 88 25 6f o 89 26 6d m 90 27 6f o 91 28 45 e 92 daia g nostic monitorin g t ype 68 29 6c l 93 enhanced o p tions f0 30 65 e 94 sff-8472 com p liance 01 rev 9.3 of sff-8472 31 63 c 95 cc ext note6 32 74 t 96 20 33 72 r 97 20 34 69 i 98 20 35 63 c 99 20 36 o p t.features 83 note6 100 20 37 vendor oui 00 101 20 38 00 102 20 39 5f 103 20 40 53 s 104 20 41 43 c 105 20 42 50 p 106 20 43 39 9 107 20 44 46 f 108 20 45 42 b 109 20 46 38 8 110 20 47 2d - 111 20 48 47 g 112 20 49 4c l 113 20 50 2d - 114 20 51 43 c 115 20 52 4e n 116 20 53 20 117 20 54 20 118 20 55 20 119 20 56 41to5a atoz 120 20 57 20 121 20 58 20 122 20 59 20 123 20 60 124 20 61 125 20 62 wavelen g th ( @ 10 p m ) 126 20 63 cc base note2 127 20 options transceiver vender sn note 3 length(9um)-km date code note 4 note5 read only vendor pn vendor rev. wavelen g th note1
- 13 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 10. enhanced monitoring functions diagnostic monitoring type, 2 wire address a0h enhanced options, 2 wire address a0h figure 12. block diagram data address bits description status(sei) 93 7 optional alarm/warning flags implemented for 1 all monitored quantities 93 6 o p tional soft tx _ disable control and 1 monitoring implemented 93 5 optional soft tx_fault monitoring 1 implemented 93 4 optional soft rx_los monitoring 1 im p lemented 93 3 optional soft rate_select control and 0 monitoring implemented 93 2-0 reserved 0 data address bits description status(sei) 92 7 reserved for legacy diagnostic 0 implementations. must be ?0? for compilance with sff-8472. 92 6 digital diagnostic monitoring implemented 1 (described in sff-8472). must be ?1? for compliance with sff-8472. 92 5 internally calibrated 1 92 4 externally calibrated 0 92 3 received power measurement type 1 0 = oma, 1 = average power 92 2 address change required. 0 (refer to sff-8472) 92 1-0 reserved 0 mod-def(1) mod-def(2) a/d serial i/f temp. mod-def(1) mod-def(2) bias tx power rx power vcc a/d serial i/f temp. ld temp tec current
- 14 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 a/d accuracy, 2 wire address a2h 12. calibration calculation data address parameter accuracy units display note 96-97 temperature +/-3 deg-c signed 2's internal temperature complement mesurement by monitor ic integer deg-c 98-99 vcc +/-3% x100volt 100-101 tx bias +/-10% x2a spec ified by nominal value 102-103 tx power +/-3db x0.1w 0 to 4dbm 104-105 rx power +/-3db x0.1w at specified transmitter ( -28 to -9dbm ) wavelength ( section 7-1 ) 106-107 laser temperature +/-0.2deg-c signed 2's complement integer deg-c 108-109 tec current +/-60ma signed 2's complement integer x 0.1ma 11. optical dwdm features data address bit description status(sei) 36 7 optional interrupt pin functionality supported (1 if supported) 1 pilot tone functionality 000b: no pilot tone functionality 001b: no pilot detection only 010b: no pilot injection only 011b: no pilot injection and detection 100b: enhanced pilot tone functionality 101b-111b: reserved 36 3 variable optical attenuator implemented (1 if implemented) 0 extended transmit power monitoring 0: deafult (sff-8472) tx power monitoring 1: extended tx power monitoring (+18.2 dbm max) wavelength monitor type in a2 byte 106-107 0: monitor is waqvelength 1: monitor is laswer temeperature 36 0 variable decision threshold (1 if implemented) 1 36 2 1 36 36 0 0 1 6-4 optical dwdm features,2wire address a0h variable decision threshold control byte 131 of table 02h is used to control the variable decision threshold function. the availability of this function is indicated in bit 0, byte 36 of a0 in the serial id section. byte 131 is a 2's complement 7 bit value (-128 - +127) the decision threshold set is given by: decision threshold = 50% + [byte(131)/256]*100%
- 15 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 13. a/d values and status converted analog values, 2wire address a2h byte bit name description 96 all temperature msb signed 2's complement integer tem perature(-40 to +125c) based on internal temperature measurement 97 all temperature lsb fractional part of temperature(count/256) 98 all vcc msb internally measured supply voltage in transeciver. 99 all vcc lsb actual voltage is full 16 bit value *100uvolt.(yields range of 0-6.55v) 100 all tx bias msb measured laser bias current in ma. bias current is full 101 all tx bias lsb 16 bit value *2 a.(full range of 0-131ma) 102 all tx power msb measured tx output power in mw. tx power is full 16 103 all tx power lsb bit value*0.1 w .(full range of -40 to+8.2dbm ) 104 all rx power msb measured rx input power in mw . rx power is full 16 105 all rx power lsb bit value*0.1 w .(full range of -40 to+8.2dbm ) 106 all laser temperature / w avelength msb 107 all laser temperature / w avelen g th lsb 108 all tec current msb measured tec current (positive is cooling) 109 all tec current lsb 110 7 tx disable state digital state of the tx disable input pin. updated within 100msec of change on pin. 110 6 soft tx disable read/write bit that allows software disable of laser. w riting ?1? disables laser. turn on/off time is 100 msec max from acknowledgement of serial byte transmission. this bit is ?or?d with the hard tx_disable pin value. note, per sfp msa tx_disable pin is default anabled unless pulled low by hardware. if soft tx disable is not implemented, the transceiver ignores the value of this bit. default power up value is 0. 110 5 reserved 110 4 rx rate select state rate select is not suppoted by dwdm sfp bit 4 is always set at 0 110 3 soft rx rate select rate selct is not supported by dw dm sfp the transceiver ignores the value of this bit 110 2 tx fault digital state of the tx fault output pin. updated within 100msec of change on pin. 110 1 los digital state of the los output pin. updated within 100msec of change on pin. 110 0 data_ready_bar indicates transceiver has achieved power up and data is ready. bit remains high until data is ready to be read at which time the device sets the bit low. 111 7-0 reserved reserved. optional status/control bits measured laser tem perature or wavelength (choice defined in a0 byte 36 bit 1)
- 16 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 14. alarm and warning flags alarm and warning flags, 2wire address a2h byte bit name description 112 7 temp high alarm set when internal temperature exceeds high alarm level. 112 6 temp low alarm set when internal temperature is below low alarm level. 112 5 vcc high alarm set when internal supply voltage exceeds high alarm level. 112 4 vcc low alarm set when internal supply voltage is below low alarm level. 112 3 tx bias high alarm set when tx bias current exceeds high alarm level. 112 2 tx bias low alarm set when tx bias current is below low alarm level. 112 1 tx power high alarm set when tx output power exceeds high alarm level. 112 0 tx power low alarm set when tx output power is below low alarm level. 113 7 rx power high alarm set when received power exceeds high alarm level. 113 6 rx power low alarm set when received power is below low alarm level. 113 5 laser t/ high alarm set when laser temperature or wavelength exceeds high alarm level. 113 4 laser t/ low alarm set when laser temperature or wavelength is below low alarm level. 113 3 tec current high alarm set when tec current exceeds high alarm level. 113 2 tec current low alarm set when tec current is below low alarm level. 113 1 reserved alarm 113 0 reserved alarm 114 all alarm mask 115 all alarm mask 116 7 temp high warning set when internal temperature exceeds high warning level. 116 6 temp low warning set when internal temperature is below low warning level. 116 5 vcc high warning set when internal supply voltage exceeds high warning level. 116 4 vcc low warning set when internal supply voltage is below low warning level. 116 3 tx bias high warning set when tx bias current exceeds high warning level. 116 2 tx bias low warning set when tx bias current is below low warning level. 116 1 tx power high warning set when tx output power exceeds high warning level. 116 0 tx power low warning set when tx output power is below low warning level. 117 7 rx power high warning set when received power exceeds high warning level. 117 6 rx power low warning set when received power is below low warning level. 117 5 laser t/ high w arning set when laser temperature or wavelength exceeds high warnin g level. 117 4 laser t/ low warning set when laser temperature or wavelength is below low warnin g level. 117 3 tec current high warning set when tec current exceeds high warning level. 117 2 tec current low warning set when tec current is below low warning level. 117 1 reserved warning 117 0 reserved warning 118 all warnin g mas k mas kin g bits corres p ondin g to w arnin g bits of b y te 116 119 all warnin g mas k mas kin g bits corres p ondin g to w arnin g bits of b y te 117 please contact sei when you used this address.
- 17 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 15. recommended interface circuit figure 14. recommended supply filtering network * temperature * supply voltage * tx bias current * tx output power * tec current * ld temperature * rx received power figure 13. recommended interface circuit transmit data 100 ? sfp module td+ td- rd+ rd- mod- def (0) mod- def (1) mod- def (2) 100 ? vcc 4.7k to tx fault tx disable 4.7k to 10k ? los 4.7k to vcct 4.7k ? host board 10k ? 10k ? vcc vcc eeprom 50 ? line fg diagnostic monitor 150 ?
- 18 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 class 1 laser product caution if this product is used under conditions not recommended in the specification or this product is used with unauthorized revisio n, classfication for laser product safety standard is invalid. classify the product again at your responsibility and take approp riate actions. 18. other precaution under such a strong vibration environment as in automobile, the performance and reliability are not guaranteed. the governmental approval is required to export this product to other countries. to dispose of these components, the appropriate procedure should be taken to prevent illegal exportation. this module must be handled, used and disposed of according to your company's safe working practice. warning do not put this product or components of this product into your mouth. this product contains material harmful to health. caution . dispose this product or equipment including this product properly as an industrial waste according to the regulations. 16. laser safety this product uses a semiconductor laser system and is a laser class 1 product acceptable fda, complies with 21cfr 1040. 10 and 1040.11. also this product is a laser class 1 product acceptable iec 60825. 17. rohs compliancy compliancy versus requirements contained inside the following reference document is guaranteed: ?directive 2002/95/ec of 27 january 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment from official journal of european union (european parliament and of the council). this product is compliant at rohs-6/6 level and contains no leaded solders. operating transceiver products can have an outer package temperature exceeding 70 degc. to reduce the risk of injury from burns, do not touch the transceiver module under any circumstances while it is operational. when installing or uninstalling products that have been operating, handle with extreme care. warning operating transceiver products can have an outer package temperature exceeding 70 degc. to reduce the risk of injury from burns, do not touch the transceiver module under any circumstances while it is operational. when installing or uninstalling products that have been operating, handle with extreme care. warning
- 19 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 19. ordering information operating case temperature tc = -5 to 70c ordering number scp9fb8-gl-cn-xxxx xxxx : channel no. channel no. frequency (thz) wavelength (nm) test & measurement ( nm ) f610 196.1 1528.77 1528.773 f600 196.0 1529.55 1529.553 f590 195.9 1530.33 1530.334 f580 195.8 1531.12 1531.116 f570 195.7 1531.90 1531.898 f560 195.6 1532.68 1532.681 f550 195.5 1533.47 1533.465 f540 195.4 1534.25 1534.250 f530 195.3 1535.04 1535.036 f520 195.2 1535.82 1535.822 f510 195.1 1536.61 1536.609 f500 195.0 1537.40 1537.397 f490 194.9 1538.19 1538.186 f480 194.8 1538.98 1538.976 f470 194.7 1539.77 1539.766 f460 194.6 1540.56 1540.557 f450 194.5 1541.35 1541.349 f440 194.4 1542.14 1542.142 f430 194.3 1542.94 1542.936 f420 194.2 1543.73 1543.730 f410 194.1 1544.53 1544.526 f400 194.0 1545.32 1545.322 f390 193.9 1546.12 1546.119 f380 193.8 1546.92 1546.917 f370 193.7 1547.72 1547.715 f360 193.6 1548.51 1548.515 f350 193.5 1549.32 1549.315 f340 193.4 1550.12 1550.116 f330 193.3 1550.92 1550.918 f320 193.2 1551.72 1551.721 f310 193.1 1552.52 1552.524 f300 193.0 1553.33 1553.329 f290 192.9 1554.13 1554.134 f280 192.8 1554.94 1554.940 f270 192.7 1555.75 1555.747 f260 192.6 1556.55 1556.555 f250 192.5 1557.36 1557.363 f240 192.4 1558.17 1558.173 f230 192.3 1558.98 1558.983 f220 192.2 1559.79 1559.794 f210 192.1 1560.61 1560.606 f200 192.0 1561.42 1560.419 f190 191.9 1562.23 1562.233
- 20 / 20 - (scp9fb8-gl) specification : ts-s07d144b june, 2008 21. for more information 20. label information u.s.a. excelight communications 4021 stirrup creek drive, suite 200 durham, nc 27703 usa tel. +1-919-361-1600 / fax. +1-919-361-1619 e-mail: info@excelight.com http://www.excelight.com europe sumitomo electric europe ltd. 220 centennial park, elstree, herts, wd6 3sl uk tel. +44-208-953-8681 / fax. +44-208-207-5950 e-mail: photonics@sumielectric.com http://www.sumielectric.com japan sumitomo electric industries, ltd. 1 taya-cho, sakae-ku, yokohama, 244-8588 japan tel. +81-45-853-7154 / fax. +81-45-851-1932 e-mail: product-info@ppd.sei.co.jp http://www.sei.co.jp/electro-optic/index_e.html

▲Up To Search▲

Price & Availability of SCP9FB8-GL-CN-F480

	To Download SCP9FB8-GL-CN-F480 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .