mixers - high ip3 - smt 9 9 - 246 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com hmc402ms8 / 402ms8e high ip3 gaas mmic mixer, 1.8 - 2.2 ghz v02.0705 general description features functional diagram input ip3: +31 dbm high side lo ultra small msop8 package: 14.8mm 2 no external components included in the hmc-dk002 designers kit electrical specifi cations, t a =25 c, lo = +17 dbm, if = 300 mhz* typical applications the hmc402ms8 & HMC402MS8E are high dynamic range passive mmic mixers in plastic surface mount 8 lead mini small outline packages (msop) cover- ing 1.8 to 2.2 ghz. excellent input ip3 performance of +31 dbm for down conversion and +27 dbm for up conversion is provided for 2.5g & 3g gsm/cdma based umts or pcs applications at an lo drive of +17dbm. with a 1db compression of +21 dbm, the rf port will accept a wide range of input signal levels. conversion loss is 8.5db typical and lo isolations are maintained at 24 to 30 db. this miniature single-end- ed monolithic gaas fet mixer does not require any external components or bias. the broad 50 to 500 mhz if frequency response will satisfy many umts/pcs transmit or receive frequency plans confi gured for high side lo. the hmc402ms8(e) input ip3 performance coupled with its high p1db rivals traditional active fet mixers while offering a much smaller 14.8mm 2 standard ic footprint, and no dc bias. parameter min. typ. max. min. typ. max. units frequency range, rf 1.8 - 2.0 2.0 - 2.2 ghz frequency range, lo 1.85 - 2.5 2.05 - 2.53 ghz frequency range, if dc - 500 dc - 330 mhz conversion loss 8.8 10.5 8.5 10.5 db noise figure (ssb) 8.8 10.5 8.5 10.5 db lo to rf isolation 24 30 21 25 db lo to if isolation 19 24 24 28 db ip3 (input) 27 30 27 31 dbm 1 db gain compression (input) 18 21 18 22 dbm lo input drive level (typical) +16 to +18 +16 to +18 dbm *unless otherwise noted, all measurements performed as a downconverter with high side lo & if = 300 mhz. high dynamic range infrastructure: ? gsm, gprs & edge ? cdma & w-cdma ? cable modem termination systems
mixers - high ip3 - smt 9 9 - 247 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com conversion gain vs. temperature @ lo = +17 dbm isolation @ lo = +17 dbm conversion gain vs. lo drive return loss @ lo = +17 dbm if bandwidth @ lo = +17 dbm *unless otherwise noted, all measurements performed as a downconverter with high side lo & if = 300 mhz. unconverter performance conversion gain @ lo = +17 dbm hmc402ms8 / 402ms8e high ip3 gaas mmic mixer, 1.8 - 2.2 ghz v02.0705 -20 -15 -10 -5 0 1.7 1.8 1.9 2 2.1 2.2 2.3 + 25c + 85c - 40c conversion gain (db) rf frequency (ghz) -20 -15 -10 -5 0 1.7 1.8 1.9 2 2.1 2.2 2.3 conversion gain (db) rf frequency (ghz) -20 -15 -10 -5 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 conversion gain return loss (db) if frequency (ghz) response (db) -25 -20 -15 -10 -5 0 1.5 1.75 2 2.25 2.5 rf lo return loss (db) rf frequency (ghz) -20 -15 -10 -5 0 1.7 1.8 1.9 2 2.1 2.2 2.3 lo = +15dbm lo = +16dbm lo = +17dbm lo = +19dbm conversion gain (db) rf frequency (ghz) -40 -30 -20 -10 0 1.7 1.8 1.9 2 2.1 2.2 2.3 rf to if lo to rf lo to if isolation (db) frequency (ghz)
mixers - high ip3 - smt 9 9 - 248 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com input ip3 vs. temperature @ lo = +17 dbm input ip3 vs. lo drive upconverter ip3 vs. lo drive, if = 200 mhz input p1db vs. temperature @ lo = +17 dbm input ip3 vs. if frequency, rf = 1.95 ghz input ip3 vs. if frequency, rf = 2.15 ghz *unless otherwise noted, all measurements performed as a downconverter with high side lo & if = 300 mhz. hmc402ms8 / 402ms8e high ip3 gaas mmic mixer, 1.8 - 2.2 ghz v02.0705 20 25 30 35 40 60 90 120 150 180 210 240 270 300 lo = +15 dbm lo = +16 dbm lo = +17 dbm lo = +19 dbm input ip3 (dbm) if frequency (mhz) 15 17 19 21 23 25 1.7 1.8 1.9 2 2.1 2.2 2.3 + 25c + 85c - 40c input p1db (dbm) rf frequency (ghz) 15 20 25 30 35 1.7 1.8 1.9 2 2.1 2.2 2.3 lo = +15dbm lo = +16dbm lo = +17dbm lo = +19dbm input ip3 (dbm) rf frequency (ghz) 20 25 30 35 40 1.7 1.8 1.9 2 2.1 2.2 2.3 lo = +15 dbm lo = +16 dbm lo = +17 dbm lo = +19 dbm input ip3 (dbm) rf frequency (ghz) 20 25 30 35 40 60 90 120 150 180 210 240 270 300 lo = +15dbm lo = +16dbm lo = +17dbm lo = +19dbm input ip3 (dbm) if frequency (mhz) 20 25 30 35 40 1.7 1.8 1.9 2 2.1 2.2 2.3 + 25c + 85c - 40c input ip3 (dbm) rf frequency (ghz)
mixers - high ip3 - smt 9 9 - 249 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com input ip2 vs. temperature @ lo = +17 dbm input ip2 vs. lo drive mxn spurious outputs nlo mrf01234 0xx-7-3-111 150275430 26264486570 38181828180 47781808382 rf freq = 1.9 ghz @ -10 dbm lo freq = 2.2 ghz @ +17 dbm all values in dbc relative to the if power level. measured as a downconverter. harmonics of lo nlo spur @ rf port lo freq (ghz) 1 2 3 4 1.8 40 30 51 57 230295153 2.2 26 32 51 50 2.4 24 36 53 49 2.6 23 43 59 53 2.8 22 41 51 71 lo = +17 dbm all values are in dbc below input lo level @ rf port. *unless otherwise noted, all measurements performed as a downconverter with high side lo & if = 300 mhz. absolute maximum ratings rf/if input +27 dbm lo drive +27 dbm storage temperature -65 to +150 c operating temperature -40 to +85 c if dc current 40 ma electrostatic sensitive device observe handling precautions 20 25 30 35 40 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 lo = +15 dbm lo = +16 dbm lo = +17 dbm lo = +19 dbm input ip2 (dbm) rf frequency (ghz) 20 25 30 35 40 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 + 25c + 85c - 40c input ip2 (dbm) rf frequency (ghz) hmc402ms8 / 402ms8e high ip3 gaas mmic mixer, 1.8 - 2.2 ghz v02.0705
mixers - high ip3 - smt 9 9 - 250 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com outline drawing notes: 1. leadframe material: copper alloy 2. dimensions are in inches [millimeters] 3. dimension does not include moldflash of 0.15mm per side. 4. dimension does not include moldflash of 0.25mm per side. 5. all ground leads must be soldered to pcb rf ground. part number package body material lead finish msl rating package marking [3] hmc402ms8 low stress injection molded plastic sn/pb solder msl1 [1] h402 xxxx HMC402MS8E rohs-compliant low stress injection molded plastic 100% matte sn msl1 [2] h402 xxxx [1] max peak refl ow temperature of 235 c [2] max peak refl ow temperature of 260 c [3] 4-digit lot number xxxx package information hmc402ms8 / 402ms8e high ip3 gaas mmic mixer, 1.8 - 2.2 ghz v02.0705
mixers - high ip3 - smt 9 9 - 251 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com pin descriptions pin number function description interface schematic 1lo this pin is ac coupled & matched to 50 ohms from 1.8 to 2.2 ghz. blocking capacitors are required if line potential is not equal to 0v. 2, 4 n/c not connected. 3, 6, 7 gnd this pin must be connected to rf ground. 5if port this pin is dc coupled. for applications not requiring operation to dc this port should be dc blocked externally using a series capacitor. choose value of capacitor to pass if frequency desired. for operation to dc, this pin must not sink/source more than 40 ma of current or failure may result. 8rf port this pin is dc coupled & matched to 50 ohms from 1.8 to 2.2 ghz hmc402ms8 / 402ms8e high ip3 gaas mmic mixer, 1.8 - 2.2 ghz v02.0705
mixers - high ip3 - smt 9 9 - 252 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com hmc402ms8 / 402ms8e high ip3 gaas mmic mixer, 1.8 - 2.2 ghz v02.0705 evaluation pcb item description j1 - j3 pcb mount sma rf connector u1 hmc402ms8 / HMC402MS8E mixer pcb [2] 101828 eval board [1] reference this number when ordering complete evaluation pcb [2] circuit board material: rogers 4350 the circuit board used in the fi nal application should use rf circuit design techniques. signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be con- nected directly to the ground plane similar to that shown. a sufficient number of via holes should be used to connect the top and bottom ground planes. the evaluation circuit board shown is available from hittite upon request. list of materials for evaluation pcb 101830 [1]
mixers - high ip3 - smt 9 9 - 253 for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com hmc402ms8 / 402ms8e high ip3 gaas mmic mixer, 1.8 - 2.2 ghz v02.0705 notes:
|
