SF60-005G thru sf60-06g page: 1 frontier electronics corp. 667 e. cochran street, simi valley, ca 93065 tel: (805) 522-9998 fax: (805) 522-9989 e-mail: frontiersales@frontierusa.com web: http://www.frontierusa.com 6a glass passivated super fast recovery rectifier SF60-005G thru sf60-06g features z super fast switching z low forward voltage z high current capability z high surge capability z high reliability z glass passivated chip junction mechanical data z case: molded plastic, do201ad, dimensions in inches and (millimeters) z epoxy: ul 94v-0 molding compound z lead: mil-std-202e, method 208c guaranteed z mounting position: any z weight: 1.2 grams maximum ratings and electrical characteristics ratings at 25 c ambient temperature unless otherwise specified single phase, half wave, 60 hz, resistive or inducti ve load. for capacitive load, derate current by 20% ratings symbol sf60 -005g sf60 -01g sf60 -015g sf60 -02g sf60 -03g sf60 -04g sf60 -05g sf60 -06g units maximum recurrent peak reverse voltage v rrm 50 100 150 200 300 400 500 600 v maximum rms voltage v rms 35 70 105 140 210 280 350 420 v maximum dc blocking voltage v dc 50 100 150 200 300 400 500 600 v maximum average forward rectified current 0.375?(9.5mm) lead length at ta=55 c i o 6.0 a peak forward surge current, 8.3ms single half sine-wave superimposed on rated load i fsm 150 a typical junction capacitance (note 1) c j 170 pf typical thermal resistance (note 2) r ja 30 /w storage temperature range t stg - 55 to + 150 operating temperature range t op - 55 to + 150 electrical characteristics (a t t a =25 c unless otherwise noted) characteristics symbol sf60 -005g sf60 -01g sf60 -015g sf60 -02g sf60 -03g sf60 -04g sf60 -05g sf60 -06g units maximum forward voltage at i o dc v f 0.95 1.25 1.85 v maximum reverse current at 25 i r 10 a maximum reverse current at 100 i r 100 a maximum reverse recovery time (note 3) t rr 35 ns note: 1. measured at 1 mhz and applied reverse voltage 0f 4.0 volts 2. both leads attached to heat sink 30 30 1t(mm) copper plate at lead length 5mm 3. reverse recovery test conditions: i f =0.5a, i r =1.0a, i rr =0.25a .375(9.5) .335(8.5) 1.0(25.4) min .220(5.6) .197(5.0) 1.0(25.4) min .052(1.3) .048(1.2)
SF60-005G thru sf60-06g page: 2 fig. 1-test circuit diagram and reve rse recovery time characteristic fig. 6-typical junction capacitance 300 200 160 140 120 100 60 40 20 10 junction capacitance (pf) t j =25 o c .1 .2 .4 1.0 2 4 10 20 40 100 reverse voltage, (v) +0.5a 0 -0.25a -1.0a trr 1cm set time base for 10/20 ns/cm fig. 3-typical reverse characteristics 1000 100 10 1.0 0.1 t j =25 o c instantaneous reverse current (ua) 20 40 60 80 100 120 140 percent of rated peak reverse voltage (%) fig. 5-maximum non-repetitive forward surge current 175 150 100 50 0 peak forward surge current (a) 8.3 ms single half sine wave (jedec method) 1 2 5 10 20 50 100 number of cycles at 60h z ratings and characteristic curve SF60-005G thru sf60-06g average forward current (a) 6.0 5.0 4.0 3.0 2.0 1.0 0 25 50 75 100 125 150 175 ambient temperature ( o c) fig. 2-typical forward current derating curve single phase half wave 60 hz resistive or inductive load fig. 4-typical instantaneous forward characteristics t j =25 o c 100.0 10.0 1.0 .1 .01 instantaneous forward current (a) SF60-005G~60-02g s f 60 - 03g ~ 60 - 0 4 g pulse width=300us 1% duty cycle .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 instantaneous forward voltage (v) sf60 05g 60 06g pulse generator ( note 2 ) (+) 25 v dc (approx) (-) d.u.t. 1 non inductive oscilloscope ( note 1 ) 50 no inductive 100 no inductive (-) (+) note: 1. rise time=7ns max. input impedance=1 mohms 22pf 2. rise time =10ns max. source impedance=50 ohms
|