product specification series: qsh /qth high speed socket 0.5 mm pitch revision: b reviewed by: jet ? 2008 samtec, inc. date: 6/19/2008 checked by: jet specification: psq-004 approved by: jet page 1 edited by : ras 1.0 scope 1.1 this specification covers performance, tests and quality requirements for the samtec qsh/qth high speed socket/terminal 0.5mm pitc h series in a 5mm height configuration (unless otherwise noted). 2.0 electrical 2.1 dielectric withstanding voltage, dwv, per eia-364-20 2.1.1 375 vac mated with qth 2.2 insulation resistance, ir, per eia-364-21 2.2.1 > 5,000 meg ohms --- pass 2.3 low level contact resistance, llcr, per eia-364--23 2.3.1 21.8 milli ohms average - contact system 2.3.2 4.1 milli ohms av erage - gnd system 2.4 current carrying capacity for a 30c temp rise, ccc, per eia-364-70 2.4.1 1.0 a (6 contacts in series) 2.4.2 7.8 a - gnd system, two banks 3.0 materials 3.1 insulator material 3.1.1 lcp 3.2 contact 3.2.1 copper alloy with gold over 50 microinches nickel 4.0 mechanical 4.1 operational temperature 4.1.1 -55 degrees c to 125 degrees c 4.2 mating/unmating forces, per eia-364-13 4.2.1 4.5/4.7 lbs respectively - one bank 4.2.2 14.5/13.3lbs respectively - three banks 4.2.3 27.2/24.8 lbs respectively - five banks 4.3 durability after 100 cycles per eia-364-17b and eia-364-31b 4.3.1 llcr change < 15.0 milli-ohms --- pass 4.4 normal force at 0.006 inches deflection, per eia-364-04 4.4.1 90 gr. www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification series: qsh /qth high speed socket 0.5 mm pitch revision: b reviewed by: jet ? 2008 samtec, inc. date: 6/19/2008 checked by: jet specification: psq-004 approved by: jet page 2 edited by : ras 5.0 environmental 5.1 thermal aging per eia-364-17 5.1.1 no evidence of physical damage seen --- pass 5.1.2 change in contact ll cr not to exceed +15.0 milli -ohms (l- plating) --- pass 5.1.3 change in ground llcr not to exc eed +5.0 milli-ohms (l- plating) --- pass 5.1.4 change in cont act llcr after thermal and gas tight not to exceed +15.0 milli- ohms (l- plating) --- pass 5.1.5 change in ground llcr after thermal and gas tight not to exceed +5.0 milli- ohms (l- plating) --- pass 5.1.6 test conditions 5.1.6.1 105 degrees c 5.1.6.2 300 hours 5.2 cyclic humidity per eia-364-31 5.2.1 no evidence of physical damage seen --- pass 5.2.2 insulation resistance > 5000 meg ohms --- pass 5.2.3 no evidence of breakdown or arcing when applying 750 vac --- pass 5.2.4 change in llcr not to exceed +15. 0 milli-ohms (l- plating) --- pass 5.2.5 test conditions 5.2.5.1 cyclic 25 degrees c to 65 degr ees c for 240 hours, at 90% to 95% rh 5.2.5.2 time condition "b" (240 hours) for method iii, excluding sub-cycle 7a and 7b 5.3 thermal shock per eia-364-32 5.3.1 no evidence of physical damage seen --- pass 5.3.2 change in signal llcr no t to exceed +15 mohm --- pass 5.3.3 change in gnd llcr not to exceed +5 mohm --- pass 5.3.4 test conditions 5.3.4.1 # thermal cycles: 5 5.3.4.2 hot temperature: 85 degrees c +3 degrees c/-0 degrees c 5.3.4.3 cold temperature: -55 degrees c +0 degrees c/-3 degrees c 5.3.4.4 dwell/configuration: 30 minutes, mated and mounted 5.3.4.5 hot/cold transition instantaneous 5.4 mechanical shock per eia-364-27 5.4.1 no evidence of physical damage seen --- pass 5.4.2 test conditions 5.4.2.1 test condition: test condition "a" 5.4.2.2 peak value: 50 g 5.4.2.3 duration: 11.0 millisec 5.4.2.4 waveform: half sine 5.4.2.5 # shocks/direction 3 shocks/3 axes (18 total) www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification series: qsh /qth high speed socket 0.5 mm pitch revision: b reviewed by: jet ? 2008 samtec, inc. date: 6/19/2008 checked by: jet specification: psq-004 approved by: jet page 3 edited by : ras 5.5 vibration per eia-364-28 5.5.1 no evidence of physical damage seen --- pass 5.5.2 change in signal llcr no t to exceed +15 mohm --- pass 5.5.3 change in gnd llcr not to exceed +5 mohm --- pass 5.5.4 test conditions 5.5.4.1 test condition: test condition v, random 5.5.4.2 frequency: 50 to 2000 hz 5.5.4.3 psd: 0.04 5.5.4.4 duration: 2 hour/axis, 3 axes total 5.5.4.5 g's: 7.3 g rms 6.0 high frequency performance 6.1 empirical boundaries on performance with sinusoidal signals 6.1.1 dv configuration, st andard configuration, single-ended signaling and standard configuration, differential pair signalin g readings based on using a -3db insertion loss point 6.1.2 dv configuration, differential pair conf iguration, differential pair readings based on using a -3db insertion loss point 6.1.3 system impedance: 50 ? and 100 ? for single-ended and differential pair respectively. 6.1.4 for complete test information, click here 6.2 standard configuration si ngle-ended signaling, 1:1 standard configuration, single-ended signaling socket header mated height configuration signaling performance qsh-xxx-01-x-d-a qth- xxx-01-x-d-a 5mm standar d single-ended 9 ghz qsh-xxx-01-x-d-a qth-xxx-02 -x-d-a 8mm standard single-ended 8.5 ghz qsh-xxx-01-x-d-a qth- xxx-03-x-d-a 11mm standar d single-ended 6 ghz qsh-xxx-01-x-d-a qth- xxx-04-x-d-a 16mm standar d single-ended 5 ghz qsh-xxx-01-x-d-a qth- xxx-08-x-d-a 30mm standar d single-ended 3 ghz www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification series: qsh /qth high speed socket 0.5 mm pitch revision: b reviewed by: jet ? 2008 samtec, inc. date: 6/19/2008 checked by: jet specification: psq-004 approved by: jet page 4 edited by : ras 6.3 standard configuration, differential pair signaling standard configuration, differential pair signaling socket header mated height configuration signaling performance qsh-xxx-01-x-d-a qth- xxx-01-x-d-a 5mm standar d differential 8 ghz qsh-xxx-01-x-d-a qth- xxx-02-x-d-a 8mm standar d differential 8 ghz qsh-xxx-01-x-d-a qth- xxx-03-x-d-a 11mm standar d differential 5 ghz qsh-xxx-01-x-d-a qth- xxx-04-x-d-a 16mm standar d differential 5 ghz qsh-xxx-01-x-d-a qth-xxx- 08-x-d-a 30mm standard differential 1.5 ghz 6.4 differential configuration, differential pair signaling differential configuration, differential pair signaling socket header mated height configuration signaling performance qsh-xxx-01-x-d-dp-a qth-xxx- 01-x-d-dp-a 5mm differential differential 9.5 ghz qsh-xxx-01-x-d-dp-a qth-xxx- 02-x-d-dp-a 8mm differential differential 8.5 ghz qsh-xxx-01-x-d-dp-a qth-xxx- 03-x-d-dp-a 11mm differential differential 6.0 ghz qsh-xxx-01-x-d-dp-a qth-xxx- 04-x-d-dp-a 16mm differential differential 5.5 ghz qsh-xxx-01-x-d-dp-a qth-xxx- 08-x-d-dp-a 30mm differential differential 7.0 ghz for additional information, contact samtec signal integrity group sig@samtec.com or 1-(800)-726-8329. www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification series: qsh /qth high speed socket 0.5 mm pitch revision: b reviewed by: jet ? 2008 samtec, inc. date: 6/19/2008 checked by: jet specification: psq-004 approved by: jet page 5 edited by : ras 7.0 processing, lead-free www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification series: qsh /qth high speed socket 0.5 mm pitch revision: b reviewed by: jet ? 2008 samtec, inc. date: 6/19/2008 checked by: jet specification: psq-004 approved by: jet page 6 edited by : ras 8.0 processing, sn63/pb37 www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification series: qsh /qth high speed socket 0.5 mm pitch revision: b reviewed by: jet ? 2008 samtec, inc. date: 6/19/2008 checked by: jet specification: psq-004 approved by: jet page 7 edited by : ras 0.13 [.005] min (ends) 8.89 [.350] 0.10 [.004] min max 0.10 [.004] (centerlines) variation max 0.10 [.004] max 0.10 [.004] max .010 [.004] max variation cte differences between pcb / fixturing during re-flow must be considered regarding connector locations end-to-end side-to-side constrained board alignment-multi connectors processed to boards 0.10 [.004] max variation 0.10 [.004] max variation .010 [.004] max variation 9.0 multi connector processing placement limitations ? see following figures 9.1 when using multiple connectors on a printed circuit board, care must be taken to ensure proper alignment and the follo wing figures illustrate the pl acement limitations for these connectors, but do not take into account the spacing required for additional components, or automatic placement / rework equipment. 9.2 for applications requiring more than two connectors per board, please contact samtec?s interconnect processing group at ipg@samtec.com 9.3 m ulti connector process ing ? constrained board alignment www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification series: qsh /qth high speed socket 0.5 mm pitch revision: b reviewed by: jet ? 2008 samtec, inc. date: 6/19/2008 checked by: jet specification: psq-004 approved by: jet page 8 edited by : ras 2 degrees max constrained board alignment-multi connectors processed to boards 0.13 [.005] min (ends) 8.89 [.350] 0.15 [.006] min max 0.15 [.006] (centerlines) variation max 0.15 [.006] max 0.15 [.006] max free floating board alignment-multi connectors processed to boards 0.15 [.006] max variation 0.15 [.006] max variation .015 [.006] max variation .015 [.006] max variation cte differences between pcb / fixturing during re-flow must be considered regarding connector locations end-to-end side-to-side 9.4 multi connector processing - free floating alignment www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification series: qsh /qth high speed socket 0.5 mm pitch revision: b reviewed by: jet ? 2008 samtec, inc. date: 6/19/2008 checked by: jet specification: psq-004 approved by: jet page 9 edited by : ras 5 degrees max free floating board alignment-multi connectors processed to boards www.datasheet.net/ datasheet pdf - http://www..co.kr/
|
