View LTL-4294-012_4325924.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

l i t e - o n e l e c t r o n i c s , i n c . p r o p e r t y o f l i t e - o n o n l y features * lead (pb) free product C rohs compliant. * high intensity. * popular t-1 3/4 diameter package. * selected minimun intensities. * general purpose leads. * reliable and rugged. package dimensions part no. lens source color LTL-4294-012 orange transparent red orange notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25mm(.010") unless otherwise noted. 3. protruded resin under flange is 1.0mm(.04") max. 4. lead spacing is measured where the leads emerge from the package. 5. specifications are subject to change without not ice. part no. : LTL-4294-012 page : 1 of 11 bns-od-c131/a4
l i t e - o n e l e c t r o n i c s , i n c . p r o p e r t y o f l i t e - o n o n l y absolute maximum ratings at t a =25 parameter maximum rating unit power dissipation 100 mw peak forward current (1/10 duty cycle, 0.1ms pulse width) 120 ma continuous forward current 30 ma derating linear from 50 0.4 ma/ reverse voltage 5 v operating temperature range -55 to + 100 storage temperature range -55 to + 100 lead soldering temperature [2 mm(.0787") from body] 260 for 5 seconds part no. : LTL-4294-012 page : 2 of 11 bns-od-c131/a4
l i t e - o n e l e c t r o n i c s , i n c . p r o p e r t y o f l i t e - o n o n l y electrical / optical characteristics at t a =25 parameter symbol min. typ. max. unit test condition luminous intensity i v 29 90 mcd i f = 10ma note 1,4 viewing angle 2 1/2 16 deg note 2 (fig.6) peak emission wavelength p 630 nm measurement @peak (fig.1) dominant wavelength d 621 nm note 3 spectral line half-width ? 40 nm forward voltage v f 2.0 2.6 v i f = 20ma reverse current i r 100 a v r = 5v capacitance c 20 pf v f = 0 , f = 1mhz note: 1. luminous intensity is measured with a li ght sensor and filter combination that approximates the cie (commission international de l'ecla irage) eye-response curve. 2. 1/2 is the off-axis angle at which the luminous intens ity is half the axial luminous intensity. 3. the dominant wavelength, d is derived from the cie chromaticity diagram and r epresents the single wavelength which defines the color of the device. 4. the iv guarantee should be added 15%. part no. : LTL-4294-012 page : 3 of 11 bns-od-c131/a4
l i t e - o n e l e c t r o n i c s , i n c . p r o p e r t y o f l i t e - o n o n l y typical electrical / optical characteristics c urves (25 ambient temperature unless otherwise noted) part no. : LTL-4294-012 page : 4 of 11 bns-od-c131/a4
l i t e - o n e l e c t r o n i c s , i n c . p r o p e r t y o f l i t e - o n o n l y features * compatible with radial lead automatic insertion e quipment. * most radial lead plastic lead lamps available pac kaged in tape and reel. * 2.54mm (0.1") straight lead spacing available. * reel packaging simplifies handling and testing. folding packaging is available by adding suffix a on option. package dimensions specification item symbol minimum maximum mm inch mm inch tape feed hole diameter d 3.8 0.149 4.2 0.165 component lead pitch f 2.3 0.091 3.0 0.118 front to rear deflection h -- -- 2.0 0.078 feed hole to bottom of component h1 21.5 0.846 22.5 0.886 feed hole to overall component height h2 29.8 1.173 31.4 1.236 lead length after component height l w0 11.0 0.433 feed hole pitch p 12.4 0.488 13.0 0.511 lead location p1 4.4 0.173 5.8 0.228 center of component location p2 5.05 0.198 7.65 0.301 total taped thickness t -- -- 0.90 0.035 feed hole location w0 8.5 0.334 9.75 0.384 adhesive tape width w1 12.5 0.492 13.5 0.531 adhesive tape position w2 0 0 3.0 0.118 tape width w3 17.5 0.689 19.0 0.748 part no. : LTL-4294-012 page : 5 of 11 bns-od-c131/a4
l i t e - o n e l e c t r o n i c s , i n c . p r o p e r t y o f l i t e - o n o n l y packing spec 2 reel per inner carton total 2000pcs per inner carton 6 inner cartons per outer carton total 12000 pcs per outer carton in every shipping lot, only the last pack will be non-full packing part no. : LTL-4294-012 page : 6 of 11 bns-od-c131/a4
l i t e - o n e l e c t r o n i c s , i n c . p r o p e r t y o f l i t e - o n o n l y bin table specification luminous intensity unit : mcd @10ma bin code min. max. q1 135 190 q2 90 135 q3 60 90 q4 40 60 q5 29 40 note: tolerance of each bin limit is 15% part no. : LTL-4294-012 page : 7 of 11 bns-od-c131/a4
l i t e - o n e l e c t r o n i c s , i n c . p r o p e r t y o f l i t e - o n o n l y cautions 1. application the leds described here are intended to be used for ordinary electronic equipment (such as office equi pment, communication equipment and household applications) .consult liteons sales in advance for information on applications in which exceptional reliability is re quired, particularly when the failure or malfunctio n of the leds may directly jeopardize life or health (such a s in aviation, transportation, traffic control equi pment, medical and life support systems and safety devices ). 2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative humidity. it is recommended that leds out of their original p ackaging are used within three months. for extended storage out of their original packagin g, it is recommended that the leds be stored in a sealed container with appropriate desiccant or in desiccators with nitrogen ambient. 3. cleaning use alcohol-based cleaning solvents such as isoprop yl alcohol to clean the leds if necessary. 4. lead forming & assembly during lead forming, the leads should be bent at a point at least 3mm from the base of led lens. do not use the base of the lead frame as a fulcrum during forming. lead forming must be done before soldering, at norm al temperature. during assembly on pcb, use minimum clinch force po ssible to avoid excessive mechanical stress. 5. soldering when soldering, leave a minimum of 2mm clearance from the base of the lens to the soldering point. dipping the lens into the solder must be avoided. do not apply any external stress to the lead frame during soldering while the led is at high temperatu re. recommended soldering conditions : soldering iron wave soldering temperature soldering time 300c max. 3 sec. max. (one time only) pre-heat pre-heat time solder wave soldering time 100c max. 60 sec. max. 260c max. 5 sec. max. note: excessive soldering temperature and/or time m ight result in deformation of the led lens or catas trophic failure of the led. ir reflow is not suitabl e process for through hole type led lamp product. part no. : LTL-4294-012 page : 8 of 11 bns-od-c131/a4
l i t e - o n e l e c t r o n i c s , i n c . p r o p e r t y o f l i t e - o n o n l y 6. drive method an led is a current-operated device. in order to e nsure intensity uniformity on multiple leds connected in parallel in an application, it is reco mmended that a current limiting resistor be incorpo rated in the drive circuit, in series with each led as sh own in circuit a below. circuit model a circuit model b led led (a) recommended circuit (b) the brightness of each led might appear diff erent due to the differences in the i-v characteris tics of those leds 7. esd (electrostatic discharge) static electricity or power surge will damage the l ed. suggestions to prevent esd damage: use a conductive wrist band or anti- electrostatic glove when handling these leds all devices, equipment, and machinery must be prope rly grounded work tables, storage racks, etc. should be properly grounded use ion blower to neutralize the static charge whic h might have built up on surface of the leds plastic lens as a result of friction between leds d uring storage and handing part no. : LTL-4294-012 page : 9 of 11 bns-od-c131/a4
l i t e - o n e l e c t r o n i c s , i n c . p r o p e r t y o f l i t e - o n o n l y suggested checking list : training and certification 1. everyone working in a static-safe area is esd- certified? 2. training records kept and re-certification dat es monitored? static-safe workstation & work areas 1. static-safe workstation or work-areas have esd signs? 2. all surfaces and objects at all static-safe wo rkstation and within 1 ft measure less than 100v? 3. all ionizer activated, positioned towards the units? 4. each work surface mats grounding is good? personnel grounding 1. every person (including visitors) handling esd sensitive (esds) items wear wrist strap, heel stra p or conductive shoes with conductive flooring? 2. if conductive footwear used, conductive floori ng also present where operator stand or walk? 3. garments, hairs or anything closer than 1 ft t o esd items measure less than 100v*? 4. every wrist strap or heel strap/conductive sho es checked daily and result recorded for all dls? 5. all wrist strap or heel strap checkers calibra tion up to date? note: *50v for blue led. device handling 1. every esds items identified by eia-471 labels on item or packaging? 2. all esds items completely inside properly c losed static-shielding containers when not at stati c-safe workstation? 3. no static charge generators (e.g. plastics) in side shielding containers with esds items? 4. all flexible conductive and dissipative packag e materials inspected before reuse or recycle? others 1. audit result reported to entity esd control co ordinator? 2. corrective action from previous audits complet ed? 3. are audit records complete and on file? part no. : LTL-4294-012 page : 10 of 11 bns-od-c131/a4
l i t e - o n e l e c t r o n i c s , i n c . p r o p e r t y o f l i t e - o n o n l y 8. reliability test classification test item test condition reference standard operation life ta= under room temperature as per data sheet maximum rating * test time= 1000hrs (-24hrs,+72hrs) mil-std-750d:1026 (1995) mil-std-883d:1005 (1991) jis c 7021:b-1 (1982) high temperature high humidity storage ta= 655 c rh= 90 95% test time= 240hrs2hrs mil-std-202f: 103b(1980) jis c 7021 : b-11(1982) high temperature high humidity reverse bias ta= 655 c rh= 90 95% vr=5v test time = 500hrs (-24hrs, +48hrs) jis c 7021 : b-11(1982) high temperature storage ta= 1055 c * test time= 1000hrs (-24hrs,+72hrs) mil-std-883d:1008 (1991) jis c 7021:b-10 (1982) endurance test low temperature storage ta= -555 c * test time=1000hrs (-24hrs,+72hrs) jis c 7021:b-12 (1982) temperature cycling 105 c 25 c -55 c 25 c 30mins 5mins 30mins 5mins 10 cycles mil-std-202f:107d (1980) mil- std-750d:1051(1995) mil-std- 883d:1010 (1991) jis c 7021: a-4(1982) thermal shock 105 5 c -55 c 5 c 10mins 10mins 10 cycles mil-std-202f:107d(1980) mil- std-750d:1051(1995) mil-std- 883d:1011 (1991) solder resistance t.sol = 260 c max dwell time= 5 secs max mil-std-202f:210a(1980) mil- std-750d:2031(1995) jis c 7021: a-1(1982) environmental test solderability t. sol = 230 5 c dwell time= 5 1secs mil-std-202f:208d(1980) mil-std-750d:2026(1995) mil-std-883d:2003(1991) jis c 7021: a-2(1982) 9. others the appearance and specifications of the prod uct may be modified for improvement, without prior notice. part no. : LTL-4294-012 page : 11 of 11 bns-od-c131/a4

▲Up To Search▲

Price & Availability of LTL-4294-012

	To Download LTL-4294-012 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .