international safety standard approvals vde0805/en60950/iec950 pending ul1950 csa 22.2 no. 950 pending sip20c series single output [ 2 year warranty ] ?updated version of sip20 ?best-of-class wide output trim range ?industry standard footprint ?high power density (60w/in 3 ) ?high efficiency 90% ?fixed frequency (500khz) ?remote on/off ?undervoltage lockout (uvlo) ?remote sense option the sip20c series are non-isolated dc/dc converters packaged in a single-in-line footprint (2.5 x 0.55 x 0.23 inches) giving designers a cost effective solution for conversion of 5vdc to 3.3vdc and lower voltages. the sip20c offers a best-of- class wide output trim range which allows maximum design flexibility and a pathway for future upgrades. for example, the 1.5v model can be trimmed as low as 1v. local voltage conversion by the sip20c from existing 5v system voltages eliminates the need for redesign of existing power architectures when voltage requirements change. the sip20c is designed for applications that include distributed power, workstations, computers and file servers. implementing state of the art surface mount technology and automated manufacturing techniques, the sip20c offers compact size and efficiencies of 90%. the sip20c is an updated version of the original sip20 and is fully compatible with the original model. specification all specifications are typical at nominal input, full load at 25 c unless otherwise stated page 122 emc characteristics (4) radiated emissions en55022/11, fcc part 15 level a electrostatic discharge en61000-4-2, iec801-2 general specifications efficiency see table isolation voltage non-isolated switching frequency fixed 500khz typ. approvals and vde0805, en60950, iec950 standards (see note 7) ul1950, csa c22.2 no. 950 material flammability ul94v-0 dimensions (lxwxh) 63.5 x 13.97 x 5.84 mm 2.5 x 0.55 x 0.23 inches pin length 0.135 ?.02 inches (3.43 ?.5mm) weight 5g (0.18oz) mtbf mil-hdbk-217f >1,000,000 hours environmental specifications thermal performance operating ambient, see curve convection cooled operating ambient, -25? to +85? 300lfm forced air see curve non-operating -55? to +100? altitude operating 10,000 feet max. non-operating 40,000 feet max. vibration 5hz to 500hz 2.4g rms (approx.) output specifications voltage adjustability s3v3 60% to 115% s2v5 60% to 110% s1v5 87% to 130% set point accuracy (see note 1) ?.7% line regulation vin = 4.5v to 5.5v ?.3% load regulation io = 0a to 6a ?.3% minimum load 0a overshoot/undershoot none ripple and noise 0 to 20mhz bw 100mv pk-pk, (see note 8) 30mv rms max. temperature coefficient ?.01%/? transient response ?.0% max. deviation (see note 2) 300? recovery to within ?.0% remote sense (see note 6) 0.5vdc compensation input specifications input voltage range 4.5 to 5.5vdc input current no load 150ma input current @ io max. and 5.3a max. vin = 0 to 5.5v input reflected ripple (see note 3) 200ma remote on/off (see note 5) start-up time 1.0ms external capacitor (see note 4) 100?
notes 1 vin = 5.0v, io = full load, t a = 25?. total error band ?.5% over all operating conditions and temperatures until end of life. 2 di/dt = 1a/1?, vin = 5vdc, tc = 25?, load change = 0.5 lo max. to lo max. and io max. to 0.5 io max. 3 with simulated source impedance of 500nh. 5hz to 20mhz. 4 use a 100? with esr = 0.045 ? max. at 100khz @ 25?. 5 referenced to ground for shutdown. if pin 6 is high unit will shut down. if pin 6 is open unit will operate as normal. 6 single line sense; 0.5vdc compensation. designate with the suffix 'r' e.g. SIP20C-05S3V3R . 7 this product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. 8 0-20mhz bw, 0.1? ceramic, 1? tantalum on output. 9 a short from +vout to ground of less than 100m ? may cause the unit to enter a non-destructive latch-up mode. if latch-up does occur the power supply to the unit may need to be cycled. 6 5 4 3 2 1 0 -25 c0 c15 c25 c35 c45 c55 c65 c75 c85 c derating curve 200 lfm 300 lfm output current (a) ambient temperature ( c) 100 lfm natural convection cooling 0.23 max. (5.84) 0.025 (0.635) square pins pc board 0.140 max. (3.556) 0.135 (3.43) 0.28 (7.11) 2.50 (63.5) 0.55 (13.97) 0.685 (17.40) 0.10 (2.54) rt1 j1 j2 1 123 56 2345 1.90 (48.26) optional remote sense pin (see note 6) all dimensions in inches (mm) recommended hole size 0.04 (1.0) plated through hole 4 trim up trim down j1 pin 5 j2 pin 5 j1 pin 2 j1 pin 5 j2 pin 5 j1 pin 2 10k ? trimpot 9 to 20 watt non-isolated dc/dc regulators dc/dc converters | 9- 20w dc/dc protection short circuit protection continuous (see note 9) input surge protection 6vdc continuous max. undervoltage protection uvlo vin <3.8v thermal protection automatic recovery, unit will shut down if rt1 exceeds 85 c (see diagram below) page 123 http://www.artesyn.com external output trimming output can be externally trimmed by using either method shown below. output input output output output efficiency regulation model power voltage voltage current current (typ.) line load number (6) (max.) (min.) (max.) 20w 4.5-5.5vdc 3.3v 0a 6a 90% 0.3% 0.3% sip20c-05s3v3 15w 4.5-5.5vdc 2.5v 0a 6a 82% 0.3% 0.3% sip20c-05s2v5 9w 4.5-5.5vdc 1.5v 0a 6a 75% 0.3% 0.3% sip20c-05s1v5 j1 pin connections pin number function 1 +vout 2 +vout 3 opt. remote sense (+) 4 +vout 5 ground j2 pin connections pin number function 1 ground 2+vin 3+vin 4 no pin 5trim 6 remote on/off data sheet ? artesyn technologies 2000 the information and specifications contained in this data sheet are believed to be correct at time of publication. however, ar tesyn technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. specifications are subject to change without notice. no rights under any patent accompa ny the sale of any such product(s) or information contained herein. 5 ds_sip20c_200001031.pdf
|
