high value / high voltage resistors type hb series literature no. 1773310 issued: 02-06 dimensions are shown for reference purposes only. dimensions are in millimetres unless otherwise specified. specifications subject to change. www.tycoelectronics.com passives.tycoelectronics.com key features up to 15kv element voltage unique specification for the most demanding applications high ratio of size to power the solution to your pcb population problems wide resistance range: 1kw to 1gw coupled with 1% tolerance gives ultimate design flexibility established product with proven reliability low inductance for the fastest switching speeds applications high voltage voltage divider surge filter balancing inrush limiting type hb series tyco electronics is a leading european supplier of standard and custom designed high value/high voltage resistors for high voltage, industrial, control, medical and general-purpose use. the hb is a tough epoxy coated high voltage resistor, with axial or radial leads, values up to 1g ohm and an operational voltage to 20kv as standard and 30kv to order. the resistors are made from quality materials for optimum reliability and stability. tyco electronics can test resistors to conform to relevant international, mil or customer specifications. tyco electronics is happy to advise on the use of resistors for high frequency applications and to supply information for high voltage use. characteristics - electrical hba hb1 hb3 power dissipation - power @ 20? (w): 0.8 2.0 4.0 @ 70?: 0.4 1.0 2.0 ohmic value - min (ohms): 1k 10k 10k max: 120m 1g 1g resistance tolerance (%): 1%, 2%, 5% 1%, 2%, 5% 1%, 2%, 5% maximum working voltage - dc or acrms (volts): 1kv 7.5kv 15kv insulation resistance - epoxy coated, @500v dc (ohms): 106m ? 106m ? 106m ? load stability - 1000hr s @ 70? (%): ?.5% ?.5% ?.5% temp. rapid change - -55? to 125? for 5 cycles ( ? r): ?.1% ?.1% ?.1% endurance - 1000 hours @ 200? ( ? r): <=2% <=2% <=2% resistance to soldering heat - 350? for 3.5seconds ( ? r): 0.05% 0.05% 0.05% temperature coefficient (ppm/?): ?00ppm/? ?00ppm/? ?00ppm/? (?0ppm/? available to special order) voltage coefficient: negligible up to 100k negligible up to 200k increasing to 0.02ppm/volt at 800k increasing to 0.01ppm/volt at 1m0 increasing to 1.0ppm/volt at 5m0 increasing to 1.0ppm/volt at 10m increasing to 2.0ppm/volt at 50m increasing to 2.0ppm/volt at 100m increasing to 8.0ppm/volt at 100m increasing to 8.0ppm/volt at 1000m ambient temperature range (?): -55 to 125 -55 to 125 -55 to 125 long term damp heat (%): 0.25% 0.25% 0.25% (steady state 56 days 95% rh at 40?) noise (quantech) dependent -20db (0.1 v/v) at lower values on resistor type and value: +10db (3.3 v/v) at higher values encapsulation: epoxy coating (optional) solvent resistance: print will withstand the action of all commonly used industrial solvents. lead material: tinned copper wire lead length: minimum 20mm lead diameter: nominal 0.6 0.05mm dimensions type a b c d e f g h hba uncoated 10.2 7 1.75 60.2 epoxy coated 12.5 8 2.6 60.5 hb01 uncoated 8.4 26 1.5 33.8 26 66 1.5 8.4 epoxy coated 10.4 26.5 3.0 35.8 26.3 66 3 9.2 hb03 uncoated 8.4 51.1 1.5 33.8 51.1 91.1 1.5 8.4 epoxy coated 10.4 52 3.0 35.8 53.5 91.1 3 9.6 e f h g d b c a
high value / high voltage resistors type hb series literature no. 1773310 issued: 02-06 dimensions are shown for reference purposes only. dimensions are in millimetres unless otherwise specified. specifications subject to change. www.tycoelectronics.com passives.tycoelectronics.com 0 20 40 60 80 100 120 140 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 power (w) ambient temperature (degc) hb3 hb1 hba how to order hb 3 1k0 j z r e common part hb- high value / high voltage resistor power rating @ 70? a - 0.4w 1 - 1.0w 3 - 2.0w resistance value 1kohm (1000 ? ) 1k0 1mohm (1000000 ? ) 1m0 tolerance f - 1% g - 2% j - 5% temp. coefficient of resistance z - 100ppm lead style r - radial leads a - axial leads (hb1, hb3 only for axial leads) coating styles e - epoxy blue coating surface temperature rise derating curve 0 0.5 1 1.5 2 2.5 3 3.5 4 100 90 80 70 60 50 40 30 20 10 0 surface temp. rise (?) power dissipation (watts) hb3 hb1 hba
|
