1 ? ha-2520/883 ha-2522/883 uncompensated, high slew rate operational amplifiers description description the ha-2520/883 and ha-2522/883 are mono- lithic operational amplifiers which deliver an unsurpassed combination of specifications for slew rate, bandwidth and settling time. these dielectrically isolated amplifiers are designed for closed loop gains of 3 or greater without exter- nal compensation. in addition, these high performance com- ponents also provide low offset current and high input impedance. the 100v/ s (min) slew rate (80v/ s for ha-2522/883) and fast settling time of these amplifiers make them ideal com- ponents for pulse amplification and data acquisition designs. to insure compliance with slew rate and transient response specifications, all devices are 100% tested for ac perfor- mance characteristics over full temperature. these devices are valuable components for rf and video circuitry requiring wideband operation. for accurate signal conditioning designs, the ha-2520/883?s superior dynamic specifications are complemented by 25na (max) offset current (50na for ha-2522/883) and offset voltage adjust capability. ordering information part number temperature range package ha2-2520/883 -55 o c to +125 o c8 pin can ha4-2522/883 -55 o c to +125 o c 20 lead ceramic lcc features ? this circuit is processed in accordance to mil-std- 883 and is fully conformant under the provisions of paragraph 1.2.1. ? high slew rate (ha-2520/883) . . . . . . . . .100v/ s (min) 120v/ s (typ) ? wide power bandwidth (ha-2520/883) . . 1.5mhz (min) ? wide gain bandwidth (ha-2520/883) . . . . .10mhz (min) 20mhz (typ) ? high input impedance (ha-2520/883). . . . . 50m ? (min) 100m ? (typ) ? low offset current (ha-2520/883) . . . . . . . . 25na (min) 10na (typ) ? fast settling (0.1% of 10v step) . . . . . . . . . 200ns (typ) ? low quiescent supply current . . . . . . . . . . 6ma (max) applications ? data acquisition systems ? rf amplifiers ? video amplifiers ? signal generators ? pulse amplification march 2002 spec number 511004-883 fn3735.1 pinouts ha-2522/883 (clcc) top view ha-2520/883 (metal can) top view 4 5 6 7 8 9 101112 13 3212019 15 14 18 17 16 bal nc v- nc nc -in +in nc nc nc v+ out nc nc nc nc bal comp nc nc + - 2 4 6 1 3 7 5 8 comp out -in v- bal +in v+ bal + - caution: these devices are sensitive to electrostatic discharge; follow proper ic handling procedures. 1-888-intersil or 321-724-7143 | intersil (and design) is a registered trademark of intersil americas inc. copyright ? intersil americas inc. 2002. all rights reserved
2 ha-2520/883, ha-2522/883 absolute maximum ratings thermal information voltage between v+ and v- terminals . . . . . . . . . . . . . . . . . . . 40v differential input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15v voltage at either input terminal . . . . . . . . . . . . . . . . . . . . . . v+ to v- peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50ma junction temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +175 o c storage temperature range . . . . . . . . . . . . . . . . . -65 o c to +150 o c esd rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000v lead temperature (soldering 10s). . . . . . . . . . . . . . . . . . . . +300 o c thermal resistance ja jc ceramic lcc package . . . . . . . . . . . . . . 85 o c/w 30 o c/w metal can package . . . . . . . . . . . . . . . . . 160 o c/w 75 o c/w package power dissipation limit at +75 o c for t j +175 o c ceramic lcc package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.33w metal can package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625mw package power dissipation derating factor above +75 o c ceramic lcc package . . . . . . . . . . . . . . . . . . . . . . . . 13.3mw/ o c metal can package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3mw/ o c caution: stresses above those listed in ?absolute maximum ratings? may cause permanent damage to the device. this is a stress o nly rating and operation of the device at these or any other conditions above those indica ted in the operational sections of this specification is not i mplied. note: 1. ja is measured with the component mounted on a low effective thermal conductivity test board in free air. see tech brief tb379 for details. operating conditions operating temperature range. . . . . . . . . . . . . . . . -55 o c to +125 o c operating supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15v v incm 1/2 (v+ - v-) r l 2k ? table 1. dc electrical performance characteristics device tested at: v supply = 15v, r source = 100 ? , r load = 500k ? , v out = 0v, unless otherwise specified. parameters symbol conditions group a subgroups temperature ha-2520/883 ha-2522/883 units min max min max input offset voltage v io v cm = 0v 1 +25 o c-88-1010mv 2, 3 +125 o c, -55 o c -10 10 -14 14 mv input bias current +i b v cm = 0v, +r s = 100k ? , -r s = 100 ? 1+25 o c -200 200 -250 250 na 2, 3 +125 o c, -55 o c -400 400 -500 500 na -i b v cm = 0v, +r s = 100 ? , -r s = 100k ? 1+25 o c -200 200 -250 250 na 2, 3 +125 o c, -55 o c -400 400 -500 500 na input offset current i io v cm = 0v, +r s = 100k ? , -r s = 100k ? 1+25 o c -25 25 -50 50 na 2, 3 +125 o c, -55 o c -50 50 -100 100 na common mode range +cmr v+ = 5v, v- = -25v 1 +25 o c +10 - +10 - v 2, 3 +125 o c, -55 o c +10 - +10 - v -cmr v+ = 25v, v- = -5v 1 +25 o c - -10 - -10 v 2, 3 +125 o c, -55 o c - -10 - -10 v large signal voltage gain +a vol v out = 0v and +10v, r l = 2k ? 4+25 o c10-7.5-kv/v 5, 6 +125 o c, -55 o c7.5 - 5 - kv/v -a vol v out = 0v and -10v, r l = 2k ? 4+25 o c10-7.5-kv/v 5, 6 +125 o c, -55 o c7.5 - 5 - kv/v common mode rejection ratio +cmrr ? v cm = +10v, v+ = +5v, v- = -25v, v out = -10v 1+25 o c80-74-db 2, 3 +125 o c, -55 o c80 - 74 - db -cmrr ? v cm = -10v, v+ = +25v, v- = -5v, v out = +10v 1+25 o c80-74-db 2, 3 +125 o c, -55 o c80 - 74 - db output voltage swing +v out r l = 2k ? 4+25 o c10-10-v 5, 6 +125 o c, -55 o c10 - 10 - v -v out r l = 2k ? 4+25 o c - -10 - -10 v 5, 6 +125 o c, -55 o c - -10 - -10 v spec number 511004-883
3 spec number 511004-883 ha-2520/883, ha-2522/883 output current +i out v out = -10v 4 +25 o c10-10-ma 5, 6 +125 o c, -55 o c 7.5 - 7.5 - ma -i out v out = +10v 4 +25 o c - -10 - -10 ma 5, 6 +125 o c, -55 o c--7.5--7.5ma quiescent power supply current +i cc v out = 0v, i out = 0ma 1+25 o c-6-6ma 2, 3 +125 o c, -55 o c-6.5- 7ma -i cc v out = 0v, i out = 0ma 1+25 o c-6--6-ma 2, 3 +125 o c, -55 o c-6.5 - -7 - ma power supply rejection ratio +psrr ? v sup = 10v, v+ = +20v, v- = -15v, v+ = +10v, v- = -15v 1+25 o c80-74-db 2, 3 +125 o c, -55 o c80 - 74 - db -psrr ? v sup = 10v, v+ = +15v, v- = -20v, v+ = +15v, v- = -10v 1+25 o c80-74-db 2, 3 +125 o c, -55 o c80 - 74 - db offset voltage adjustment +v io adj note 1 1 +25 o cv io -1 - v io -1 - mv 2, 3 +125 o c, -55 o cv io -1 - v io -1 - mv -v io adj note 1 1 +25 o cv io +1 - v io +1 - mv 2, 3 +125 o c, -55 o cv io +1 - v io +1 - mv note: 2. offset adjustment range is [v io (measured) 1mv] minimum referred to output. this test is for functionality only to assure adjustment through 0v. table 2. ac electrical performance characteristics device tested at: v supply = 15v, r source = 50 ? , r load = 2k ? , c load = 50pf, a vcl = +3v/v, unless otherwise specified. parameters symbol conditions group a subgroups temperature ha-2520/883 ha-2522/883 units min max min max slew rate +sr v out = -5v to +5v 25% +sr 75% 7+25 o c 100 - 80 - v/ s 8a, 8b +125 o c, -55 o c84 - 60 - v/ s -sr v out = +5v to -5v 75% -sr 25% 7+25 o c 100 - 80 - v/ s 8a, 8b +125 o c, -55 o c84 - 60 - v/ s rise and fall time t r v out = 0 to +200mv 10% t r 90% 7+25 o c-50-50ns 8a, 8b +125 o c, -55 o c- 55 - 60ns t f v out = 0 to -200mv 10% t f 90% 7+25 o c-50-50ns 8a, 8b +125 o c, -55 o c- 55 - 60ns overshoot +os v out = 0 to +200mv 7 +25 o c-40-50% 8a, 8b +125 o c, -55 o c- 45 - 60% -os v out = 0 to -200mv 7 +25 o c-40-50% 8a, 8b +125 o c, -55 o c- 45 - 60% table 1. dc electrical performance characteristics (continued) device tested at: v supply = 15v, r source = 100 ? , r load = 500k ? , v out = 0v, unless otherwise specified. parameters symbol conditions group a subgroups temperature ha-2520/883 ha-2522/883 units min max min max
4 spec number 511004-883 ha-2520/883, ha-2522/883 table 3. electrical performance characteristics device characterized at: v supply = 15v, r load = 2k ? , c load = 50pf, a v 3, c comp = 0pf, unless otherwise specified. parameters symbol conditions notes temperature ha-2520/883 ha-2522/883 units min max min max differential input resistance r in v cm = 0v 1 +25 o c50-40-m ? full power bandwidth gbwp v o = 200mv, f o = 10khz 1 +25 o c10-10-mhz v o = 200mv, f o = 1mhz 1 +25 o c10-10-mhz full power bandwidth fpbw v peak = 10v 1, 2 +25 o c 1.6 - 1.2 - mhz minimum closed loop stable gain clsg r l = 2k ? , c l = 50pf 1 -55 o c to +125 o c+3 - +3 - v/v quiescent power consumption pc v out = 0v, i out = 0ma 1, 3 -55 o c to +125 o c - 195 - 210 mw notes: 1. parameters listed in table 3 are controlled via design or proc ess parameters and are not directly tested at final production. these param- eters are lab characterized upon initial design release, or upon design changes. these parameters are guaranteed by characteriz ation based upon data from multiple production runs which reflect lot to lot and within lot variation. 2. full power bandwidth guarantee based on slew rate measurement using fpbw = slew rate/(2 v peak ). 3. quiescent power consumption based upon quiescent supply current test maximum. (no load on outputs.) table 4. electrical test requirements mil-std-883 test requirements subgroups (see tables 1 and 2) interim electrical parameters (pre burn-in) 1 final electrical test parameters 1 (note 1), 2, 3, 4, 5, 6, 7, 8a, 8b group a test requirements 1, 2, 3, 4, 5, 6, 7, 8a, 8b groups c and d endpoints 1 note: 1. pda applies to subgroup 1 only.
5 all intersil u.s. products are manufactured, assembled and tested utilizing iso9000 quality systems. intersil corporation?s quality certifications can be viewed at www.intersil.com/design/quality intersil products are sold by description only. intersil corporation reserves the right to make changes in circuit design, soft ware and/or specifications at any time without notice. accordingly, the reader is cautioned to verify that data sheets are current before placing orders. information furnishe d by intersil is believed to be accurate and reliable. however, no responsibility is assumed by intersil or its subsidiaries for its use; nor for any infringements of paten ts or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of intersil or its subsidiari es. for information regarding intersil corporat ion and its products, see www.intersil.com sales office headquarters north america intersil corporation 7585 irvine center drive suite 100 irvine, ca 92618 tel: (949) 341-7000 fax: (949) 341-7123 intersil corporation 2401 palm bay rd. palm bay, fl 32905 tel: (321) 724-7000 fax: (321) 724-7946 europe intersil europe sarl ave. william graisse, 3 1006 lausanne switzerland tel: +41 21 6140560 fax: +41 21 6140579 asia intersil corporation unit 1804 18/f guangdong water building 83 austin road tst, kowloon hong kong tel: +852 2723 6339 fax: +852 2730 1433 ha-2520/883, ha-2522/883 die characteristics die dimensions: 67 x 57 x 19 mils 1 mils 1700 x 1440 x 483 m 25.4 m metallization: type: al, 1% cu thickness: 16k ? 2k ? glassivation: type: nitride (si3n4) over silox (sio2, 5% phos.) silox thickness: 12k? 2k? nitride thickness: 3.5k? 1.5k? worst case current density: 0.26 x 10 5 a/cm 2 substrate potential (powered up): unbiased transistor count: ha-2520/883: 40 ha-2522/883: 40 process: bipolar dielectric isolation metallization mask layout ha-2520/883, ha-2522/883 comp v+ out bal bal -in +in v- spec number 511004-883
|
