cat.8100p aluminum electrolytic capacitors voltage capacitance 105 c marking lot no. x2p 10 16v plastic platform 0.3max. l 0.3 f d 0.5 b 0.2 c 0.2 0.5max. a 0.2 a 0.2 e positive negative a b c e l 4 1.8 4.3 4.3 1.0 5.8 5 2.1 5.3 5.3 1.3 5.8 6.3 2.4 6.6 6.6 2.2 5.8 0.5 ~ 0.8 (mm) f d voltage mark for 6.3v is 6v . u 1 u 2 t 3 1 4 c 5 1 6 0 7 0 8 m 9 c 10 r 11 1 12 g 13 s 14 configuration taping code capacitance tolerance ( 20%) rated voltage (16v) rated capacitance (10 m f) series name type ut series 6mml chip type , wide temperature range chip type with load life 2000 hours at +105?. designed for surface mounting on high density pc board. applicable to automatic mounting machine using carrier tape. chip type specifications category temperature range rated voltage range rated capacitance range capacitance tolerance leakage current tan d stability at low temperature endurance shelf life resistance to soldering heat marking performance characteristics item ?5 ~ +105? 4 ~ 50v 0.1 ~ 100 m f ?0% at 120hz, 20? after 2 minutes' application of rated voltage, leakage current is not more than 0.01 cv or 3(?), whichever is greater. black print on the case top. measurement frequency :120hz, temperature : 20? after 2000 hours' application of rated voltage at 105? , capacitors meet the characteristics requirements listed at right. after leaving capacitors under no load at 105? for 1000 hours, they meet the specified value for endurance characteristics listed above. type numbering system (example : 16v 10 m f) dimensions rated ripple (ma rms) at 105? 120hz rated voltage(v) tan d ( max.) 4 0.37 50 0.12 35 0.13 25 0.16 16 0.20 10 0.24 6.3 0.28 measurement frequency : 120hz z?5?/ z+20? z?0?/ z+20? rated voltage(v) impedance ratio zt/z20(max.) 4 6 12 6.3 3 8 10 3 5 16 2 4 25 2 3 35 2 3 50 2 3 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 0r1 r22 r33 r47 010 2r2 3r3 4r7 100 220 330 470 101 4 5 5 6.3 22 30 36 60 0g 4 0j 6.3 1a 10 1c 16 1e 25 1v 35 1h 50 4 5 5 6.3 22 30 36 60 5 5 6.3 6.3 27 35 46 60 4 5 6.3 6.3 18 30 40 50 4 5 6.3 6.3 13 23 38 48 4 5 6.3 15 25 42 4 4 4 4 4 4 4 5 6.3 case size 1.0 2.6 3.2 3.8 6.2 11 14 19 30 allowable ripple cap.( m f) v code the capacitors shall be kept on the hot plate maintained at 250? for 30 seconds. after removing from the hot plate and restored at room temperature, they meet the characteristics requirements listed at right. tan d capacitance change 200% or less of initial specified value leakage current initial specified value or less within ?5% of initial value (16v or less) within ?0% of initial value (25v or more) capacitance change leakage current tan d within ?0% of initial value initial specified value or less initial specified value or less rated ripple please refer to page 3 for the minimum order quantity. taping specifications are given in page 21. frequency coefficient of rated ripple current coefficient frequency 50 hz 120 hz 300 hz 1 khz 10 khz ~ 0.70 1.00 1.17 1.36 1.50
|
