parameter symbol unit conditions ratings absolute maximum ratings electrical characteristics parameter symbol min typ max unit conditions ratings (ta=25?) power supply voltage input terminal voltage input terminal current dg terminal voltage input threshold voltage inpup current operating power supply voltage quiescent circuit current thermal shutdown operating temperature load open detection threshold voltage dg leak current low level dg output voltage output transfer time dg output transfer time (v b = 14v, ta=25? unless otherwise specified) output on resistance channel temperature operating temperature storage temperature v b v in i in v b (opr) v in = 0v, v out =0v i o =1a i o = 1a, ta=80? ta= ?0 to +105? ta= ?0 to +105? v in =5v v in =0v v out =v o ?.5v v out =0v r l =14 ? , v out =v b ?v r l =14 ? , v b 10% v dg = 5.5v i dg = 1.6ma v 50 2.0 1.8 70 1 5.5 35 ma 200 m ? 350 m ? 3.0 v v 200 12 a 165 5 3 4.5 70 3 140 35 0.15 70 45 90 20 0.5 140 120 a 155 1.5 ? a v s s a v s iq output leak current v out =0v 1.4 1.0 100 a i o , leak r ds (on) v ihth v ilth i ih i il t tsd overcurrent protection starting current internal current limit 1.9 a i s i lim vopen t on t off v dgl i dg t plh t phl s v dg v ds i o p d i f tch t op tstg output on output off output on output off v v ta=25?, all circuit operating ma v v a w a ? ? ? 35 ?.3 to 7 5 ?.3 to 7 dg terminal current drain to source voltage output current power dissipation source to drain di forward current i dg ma 5 v b ?5 1.8 2.7 0.8 150 ?0 to +105 ?0 to +150 parameter unit ratings recommended operating conditions (for one channel) power supply voltage v ih v il i o r in r dg 5.5 4 ?.3 10 10 16 5.5 0.9 1 20 20 v v v a k ? k ? external dimensions (unit: mm) features built-in diagnostic function to detect short and open circuiting of loads and output status signals dmos 3ch output allows on/off using c-mos logic level built-in overcurrent and thermal protection circuits 44 high-side power switch ics [with diagnostic function, surface-mount 3-circuits] SPF5007 min max block diagram (for one channel) standard connection diagram timing chart in dg v b gnd out thermal protect input logic lavel shifting dg logic open/short sense charge pump current limit clamp chopper bias in2 in3 in1 gnd1 2 13 v b 1 717 18 38 5,6 10,11 20,21 4 5v 9 19 gnd2 gnd3 c p u SPF5007 r dg dg1 out1 out2 out3 dg2 dg3 r dg r dg r in r in r in * r in and r dg are needed to protect cpu and SPF5007 in case of reverse connection of v b terminal. * make v b of 1pin and 13pin short from the fin to be plated by solder. 1.0 10.5 0.3 +0.1 0.05 0.25 +0.15 0.05 2.0 +0.2 0.8 fin thickness 17.28 0.2 2.5 0.2 7.5 0.2 15.58 0.2 1.27 0.25 24 112 13 0.4 +0.15 0.05 a b a: part no. b: lot no. load load load v b v in on v in off v o open ocp tsd normal normal over- heat normal normal normal shorted load open load high inpidance internal current limit tsd on tsd off v in v out i out dg v in dg open load normal mode shorted load overheat h l v o h l h l h l h h h h h l l l l l (limiting) h l l l l l
|
