electronic control gear quicktronic? dimmable for fh-lamps, single-lamp version qt-fh 1x14/230-240 dim page 1 h b h l b a l n l 1 2 3 4 - + reference : qt-fh 1x14/230-240 dim for lamp : 1x fh 14 w mains voltage [v] : 230/240 permissible voltage fluctuations [v] : 198 - 264 permissible battery voltage [v] : 176 - 254 lamp start : warm start within 2 s mains frequency [hz] : 0/50 - 60 operating frequency [khz] : approx. 40 at 100% luminous flux, approx. 100 at 3% luminous flux mains current [a] : 0,09 power factor [c] : 0,95 system wattage [w] : 18 luminous flux [lm] : 1350 temperature range [c] : +5 - +50 radio interference suppression : to din vde 0875/cispr 15/en 55015 harmonics : to din vde 0712 part 23/iec 929/iec 555-2/en 60929 immunity : to en 61547 length l [mm] : 359 width b [mm] : 30 height h [mm] : 30 distance between holes a [mm] : 350 standard pack [pcs] : 12 weight [g] : 310 quicktronic? dimmable for fh?/fq? lamps this electronic high-frequency control gear enables fh? and fq? lamps to be dimmed from 100% to 3% (1%) luminous flux via a 1 - 10v dc control line. the 1-10 v control line allows a wide variety of possible connections, ranging from simple manual control units for small systems through daylight-controlled regulation systems to modern energy management systems with pc and digital i-bus technology. quicktronic? dimmable goes beyond all current conventional and electronic solutions not just in terms of lighting comfort and energy consumption, but also in simplicity of operation and installation. comfort: - dimmable from 100% to 3% luminous flux for fh? lamps - dimmable from 100% to 1% luminous flux for fq? lamps - flicker-free starting at all dimmer settings - numerous control options with a low-voltage control signal (1 - 10 v) - electronic control gear from different circuits can be dimmed together on different phases
electronic control gear quicktronic? dimmable for fh-lamps, single-lamp version qt-fh 1x14/230-240 dim page 2 - easy to incorporate into existing lighting control systems economy: - potentially large energy savings thanks to daylight-dependent lighting control - long lamp life - protective warm start safety: - safety shutdown of the power supply to defective lamps - compliance with european standards for safety, operation and emc - overvoltage protective cutout for short-duration voltage surges (din vde 0160) and for temporary overvoltages - greater fire protection because lamps operate at lower temperatures and luminaires can be constructed to meet en 60598/din vde 0710 and din vde 0711 standards - can be used in emergency lighting systems as per din vde 0108. applications: adjustable lighting in conference rooms, film projection rooms, exhibition rooms, cad and pc rooms, control rooms, film recording studios, and for energy savings in offices with daylight-dependent lighting control. general: - supply voltage: 230v/240v - mains frequency: 0/50 to 60 hz - lamp start: warm start within 2 s. lamp will start at any dimmer setting. - radio interference suppression: to din vde 0875/cispr 15/en 55015 - mains harmonics: to din vde 0712 part 23/iec 929/en 61000-3-2/en 60929 - immunity to en 61547 - same luminous flux for ac and dc operation. - values for luminous flux, mains current and system wattage at a dimmer setting of 100% - max. 0.6 ma control current at the 1-10v interface
|
