View EVL6563S-400W_1487904.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

march 2010 doc id 17009 rev 1 1/43 um0896 user manual steval-pcc012v1 stm32f107xx connectivity gateway, demonstration board 1 introduction this user manual describes the implementation of the steval-pcc012v1 demonstration board. the steval-pcc012v1 demonstration board is equipped with an ethernet interface, four digital/analog extension connectors (i 2 c, spi, etc.), two footprint positions for two different wi-fi modules, an ofdm prime power line networking extension connector and a microsd? card socket with spi interface. it also features a 5-way general purpose joystick, four general purpose leds and two leds dedicated to user interface. the demonstration board also includes digital/analog input/output connectors pinout compatible with existing demonstration boards from stmicroelectronics?: steval-cca021v1 - audio demonstration board (stereo dac, class-d amplifier) steval-mki0xxv1 - mems demonstration boards (gyroscope, accelerometer) that are compatible with 24 dil socket evalst7590-1 - st7590 ?prime? board - narrow-band ofdm power line networking prime compliant system-on-chip. the demonstration board can be supplied from a standard dc power supply (7 - 35 v dc) or directly using a 24 v dc industrial mains supply. figure 1. steval-pcc012v1 www.st.com
contents um0896 2/43 doc id 17009 rev 1 contents 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 steval-pcc012v1 key features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.1 order code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3 block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4 demonstration board layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5 configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5.1 ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5.2 power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5.3 general purpose 5-way joystick sw1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5.4 leds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5.5 spi bus communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5.6 i 2 c, usart signals branching for mems, wi-fi, digital audio and plm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.7 analog signals branching for mems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.8 clock source setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.9 reset button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.10 usb-otg configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.11 microsd card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.12 wi-fi optional modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.12.1 wi-fi optional module-1 u9 settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.12.2 wi-fi optional module-2 u10 settings and signal description . . . . . . . . 16 6 connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6.1 jtag connector cn1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6.2 audio extension connector cn3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6.3 analog/digital mems extension connector cn6 and cn8 . . . . . . . . . . . . 18 6.4 power line networking extension connector cn7 . . . . . . . . . . . . . . . . . . . 20 6.5 power test points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 6.6 usb connector cn4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
um0896 contents doc id 17009 rev 1 3/43 6.7 u10 wi-fi module-2 debugging signals txupd and rxupd . . . . . . . . . . . 22 6.8 ethernet rj45 connectors cn5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 6.9 microsd card connector cn9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 6.10 schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 6.11 power supply connectors cn2, p2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 7 evaluation software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 7.1 connectivity gateway demonstration application (cg demonstration) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 8 bom of the board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 9 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
list of tables um0896 4/43 doc id 17009 rev 1 list of tables table 1. order code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 table 2. default configuration of the ethernet phy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 table 3. ethernet phy configuration defined by sb1, sb2 and sb3 . . . . . . . . . . . . . . . . . . . . . . . . 10 table 4. logical levels on cfg0, cfg1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 table 5. ethernet phy configuration defined by cfg0, cfg1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 table 6. u2 dc/dc converter jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 table 7. joystick direction mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 table 8. led mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 table 9. mems, wi-fi, plm i 2 c and usart signals branching . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 table 10. digital audio i 2 c branching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 table 11. analog signals branching of stm32 pins pa6 and pa7 to analog mems . . . . . . . . . . . . . 14 table 12. clock source setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 table 13. usb-otg configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 table 14. optional wi-fi modules configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 table 15. wi-fi optional module-1 u9 settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 table 16. wi-fi optional module-2 u10 settings and signal description . . . . . . . . . . . . . . . . . . . . . . . 16 table 17. jtag connector signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 table 18. description of the i 2 s audio connector pins of the ts4657 audio card . . . . . . . . . . . . . . . 18 table 19. digital mems connector signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 table 20. gpio and analog mems connector signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 table 21. connector cn7 for plm, usart and spi interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 table 22. test points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 table 23. usb connector cn4 signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 table 24. u10 wi-fi module-2 debugging signals txupd and rxupd . . . . . . . . . . . . . . . . . . . . . . . . 22 table 25. rj45 connectors cn5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 table 26. microsd card connector cn9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 table 27. power supply connector cn2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 table 28. power supply connector p2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 table 29. board function indication after reset for server/clients example . . . . . . . . . . . . . . . . . . . . . 38 table 30. bill of material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 table 31. document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
um0896 list of figures doc id 17009 rev 1 5/43 list of figures figure 1. steval-pcc012v1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 figure 2. steval-cca021v1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 figure 3. steval-mki0xxv1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 4. block diagram of steval-pcc 012v1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 figure 5. steval-pcc012v1 - connector map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 figure 6. sd card formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 figure 7. jtag connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 figure 8. i 2 s audio connector of the ts4657 audio card - schematic . . . . . . . . . . . . . . . . . . . . . . . . 17 figure 9. digital mems connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 figure 10. gpio and analog connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 figure 11. connector cn7 for plm, usart and spi interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 figure 12. ethernet rj45 connectors cn5 - front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 figure 13. microsd card connector cn9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 figure 14. power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 figure 15. stm32 - part 1(inputs, outputs, clock, reset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5 figure 16. stm32 - part 2 (jtag, leds, audio extension connector). . . . . . . . . . . . . . . . . . . . . . . . . 26 figure 17. stm32 - part 3 (joystick, analog decoupling, dac_fmt signals) . . . . . . . . . . . . . . . . . . . 27 figure 18. ethernet - part 1 (phy pinout) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 figure 19. ethernet - part 2 (overvoltage protection, phy configuration) . . . . . . . . . . . . . . . . . . . . . . 29 figure 20. ethernet - part 3 (magnetics) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 figure 21. usb-otg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 figure 22. wi-fi module-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 figure 23. wi-fi module-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 figure 24. microsd card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 figure 25. mems extension connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 figure 26. power supply connector cn2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 figure 27. power supply connector p2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 figure 28. connectivity gateway webserver demonstration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
steval-pcc012v1 key features um0896 6/43 doc id 17009 rev 1 2 steval-pcc012v1 key features 1 x ethernet rj45 connectors (st802rt1a) usb-otg with 0.5 a onboard power supply general purpose extension connector with gpios, adc, i 2 c, spi dc/dc converter l7986a (+24 v / +5 v) microsd card? socket two positions for optional wi-fi modules 4 + 2 leds, 5-way general purpose joystick and system reset button digital/analog extension connectors compatible with steval-mki0xxv1 digital/analog extension connectors compatible with steval-cca021v1 extension connector for st7590 ?prime? board - narrow-band ofdm power line networking prime compliant system-on-chip. figure 2. steval-cca021v1
um0896 steval-pcc012v1 key features doc id 17009 rev 1 7/43 figure 3. steval-mki0xxv1 refer to user manual um0722 for details on how to use the steval-cca021v1. 2.1 order code table 1. order code part number note steval-pcc012v1 stm32f107xx connectivity gateway steval-cca021v1 audio demonstration board (stereo dac, class-d amplifier)
block diagram um0896 8/43 doc id 17009 rev 1 3 block diagram figure 4. block diagram of steval-pcc012v1 /ptional 7i &i module 3424! 34-& $#$# 6 6 way joystick 2eset 2* *4!' /ptional 7i &i module '0)/ extension connector ,%$s -icro3$ #a rd 53" /4' !udioextension co nnector #rystals -%-3 analog extension connector -%-3 digital extension connector 0owerline modem extension connector !-
um0896 demonstration board layout doc id 17009 rev 1 9/43 4 demonstration board layout figure 5. steval-pcc012v1 - connector map cn1 jtag cn8 analog digital extension jp2, 3 i 2 c reset crystal switch power line network extension connector sb1, 2, 3 ethernet options cn6 digital extension optional wi-fi module-1 wi-fi module-2 cn9 microsd socket cn5 ethernet debug interface txupd, rxupd for optional wi-fi module-2 p2, cn2 power plugs 7-24 vdc cn3 audio extension usb-otg leds joystick test points
configuration um0896 10/43 doc id 17009 rev 1 5 configuration 5.1 ethernet an ethernet phy u5 is available on the board. it is connected through the media independent interfaces (mii, and reduced mii, rmii) to the ethernet macs of the stm32? microcontroller. if the ethernet phy is used, the crystal resonator x2 must be chosen as stm32 clock source. the clock source for the phy is the clock output mco signal of the stm32 microcontroller. to operate in mii mode, the mco signal must be configured to output 25 mhz, for rmii, 50 mhz. by default the mii address of the ethernet phy is 0x01 and the initial configuration of the ethernet phy is selected as shown in table 2 . there are two leds embedded in rj45 connector (cn5) which are used to indicate the status of the line: the green led in the connector is switched on continuously when the ethernet link is established with the counterpart. the yellow led in the connector blinks when a transmission or a reception is ongoing. the ?serial management interface? (smi) is part of the mii interface and is used to transfer management information between mac and phy (access of the phy registers). the phy can communicate with the stm32 microcontroller over mii or rmii. sb1, sb2 and sb3 must be configured according to the mode chosen. mii is chosen as a default option. table 2. default configuration of the ethernet phy function default configuration auto negotiation enabled 10/100 mb 100 mb selected for auto negotiation advertisement half/full duplex full duplex selected for auto negotiation advertisement internal loopback disabled power-down disabled (phy is not in power-down) mii/rmii mode mii selected table 3. ethernet phy configuration defined by sb1, sb2 and sb3 function mii rmii sb1 removed fit 0 resistor sb2 removed fit 0 resistor sb3 fit 0 resistor removed
um0896 configuration doc id 17009 rev 1 11/43 this strapping option pair determines the operating mode of the mac data interface. default operation (no pull-ups) will enable normal mii mode of operation. st rapping cfg0 high will cause the device to be in rmii mode of operation, determined by the status of the cfg1 strap. since the pins include internal pull-downs, the default values are 0. note: important: to choose between mii and rmii the pin rxdv of the phy must be pulled high for rmii and pulled low for mii during reset or power-up of the phy. 5.2 power supply the steval-pcc012v1 demonstration board is designed to be powered by a 24 v dc power supply from cn2, p2. the board is protected against overvoltage by d4 transil? diode (sm6t33a) and against possible reverse polarity voltage from a wrong power plug-in by d1 schottky diode (stps3l40u). the input voltage is connected to the dc/dc converter u2 (l7986a). table 4. logical levels on cfg0, cfg1 jumper description configuration cfg0 (3-pin resistor) (2.2 k ) cfg0 = 0, default the resistor must be placed as shown: cfg0 = 1 the resistor must be placed as shown: cfg1 (3-pin resistor) (2.2 k ) cfg1 = 0, default the resistor must be placed as shown: cfg1 = 1 the resistor must be placed as shown: table 5. ethernet phy configuration defined by cfg0, cfg1 function cfg0 cfg1 mii 0 x rmii 1 0 table 6. u2 dc/dc converter jumpers jumper description configuration r4 to run dc/dc u2 on higher frequency r4 must be assembled with 102 k resistor. other components of the dc/dc must be changed accordingly. ( default - not assembled )
configuration um0896 12/43 doc id 17009 rev 1 5.3 general purpose 5-way joystick sw1 a 5-way general purpose joystick is available on the top side of the board. 5.4 leds 4 general purpose leds (ld1-ld4) are available on the top side of the board. all leds are switched on when the related gpio pin is driven low. 5.5 spi bus communication spi signals are connected to the mems connector, wi-fi module and plm. use carefully the signal enable of the listed devices to select only one at a time. spi signals can be also configured as analog inputs of the stm32 microcontroller adc for optionally attached analog mems module. please refer to section 5.7 for details. table 7. joystick direction mapping stm32 pin mapping joystick function pe14 central button pe13 direction right pe12 direction left pe11 direction down pe10 direction up table 8. led mapping stm32 pin mapping led pd15 ld1 pd14 ld2 pe8 ld3 pe9 ld4
um0896 configuration doc id 17009 rev 1 13/43 5.6 i 2 c, usart signals branching for mems, wi-fi, digital audio and plm table 9. mems, wi-fi, plm i 2 c and usart signals branching jumper description configuration jp2 (3-pin resistor) pb7 is connected to mems extension connector as i 2 c sda. the jumper must be set as shown: pb7 is connected as usart1_rx to wi-fi 2 position 10 and plm. the jumper must be set as shown: jp3 (3-pin resistor) pb6 is connected to mems extension connector as i 2 c scl. the jumper must be set as shown: pb6 is connected as usart1_tx to wi-fi 2 position 10 and plm. the jumper must be set as shown: table 10. digital audio i 2 c branching jumper description configuration jp6 (3-pin resistor) i 2 c sda is connected to dac_ftm2 signal of cn3 (audio). the jumper must be set as shown: gpio pe0 is connected to dac_ftm2 signal of cn3 (audio). the jumper must be set as shown: jp7 (3-pin resistor) i 2 c scl is connected to dac_ftm1 signal of cn3 (audio). the jumper must be set as shown: gpio pe1pb6 is connected to dac_ftm1 signal of cn3 (audio). the jumper must be set as shown:
configuration um0896 14/43 doc id 17009 rev 1 5.7 analog signals branching for mems 5.8 clock source setting table 12. clock source setting the benefit of using crystal resonator of desired frequency is described in steval- cca021v1 user manual um0722. the correct crystal resonator frequency must be chosen with regard to using phy or not. if the phy is used, only x2 can be used. 5.9 reset button a manual reset button (reset) is available on the board top side. it resets the stm32 microcontroller, both optional wi-fi modules u9, u10 and the ethernet phy u8. table 11. analog signals branching of stm32 pins pa6 and pa7 to analog mems jumper description configuration r63 (0 resistor) adc_in6 is connected to analog mems connector (out1 signal) (stm32 pin pa6 can be also configured as spi miso) r63 assembled adc_in6 is disconnected to analog mems connector (out1 signal) r63 not assembled r64 (0 resistor) adc_in7 is connected to analog mems connector (memsref signal) (stm32 pin pa7 can be also configured as spi mosi) r64 assembled adc_in7 is disconnected to analog mems connector (memsref signal) r64 not assembled jumper description configuration jp1 (3-pin resistor) crystal resonator x1 of 14.7456 mhz is connected to the stm32 ( default ) crystal resonator x2 of 25.0000 mhz is connected to the stm32
um0896 configuration doc id 17009 rev 1 15/43 5.10 usb-otg configuration the stm32 microcontroller can distinguish between the host and device mode of the connected usb circuit by reading id pin. it is possible to disconnect id pin from usb connector cn4 (see ta bl e 1 3 ). table 13. usb-otg configuration 5.11 microsd card the microsd card connector connected to the spi1 interface of the stm32 microcontroller is available on the board. microsd card detection is done through pa4 gpio signal when the card is inserted. figure 6. sd card formats jumper description configuration r32 when 0 resistor is assembled in this position, the id signal of the stm32 microcontroller and the id signal of the connector cn4 are interconnected. otherwise there are disconnected. ( default - assembled )
configuration um0896 16/43 doc id 17009 rev 1 5.12 wi-fi optional modules there are two positions for optional wi-fi modules: table 14. optional wi-fi modules configuration 5.12.1 wi-fi optional module-1 u9 settings 5.12.2 wi-fi optional module-2 u10 settings and signal description table 16. wi-fi optional module-2 u10 settings and signal description position interface used note u9 - module-1 spi1 + cs_wi-fi u10 - module-2 usart1 these signals are shared with i 2 c for mems extension connector, refer to section 5.6 . jp2, jp3 must be configured accordingly. table 15. wi-fi optional module-1 u9 settings jumper description configuration jp4 (3-pin resistor) jtgenpb7 is pulled to gnd. the jumper with resistance of 10 k must be set as shown: jtgenpb7 is pulled to +3.3 v. the jumper with resistance of 10 k must be set as shown: jp5 (3-pin resistor) jtgrnpb6 is pulled to gnd. the jumper with resistance of 10 k must be set as shown: jtgtn is pulled to +3.3 v. the jumper with resistance of 10 k must be set as shown: signal on u10 sdio description spi description stm32 spi signals gpio4 - sd_cmd di mosi mosi gpio5 - sd_d0 do miso miso gpio6 - sd_d1 irq ? ? gpio7 - sd_d2 nc ? ? gpio8 - sd_3 c s s s scs_n gpio9 - sd_clk sck sck sck
um0896 connectors doc id 17009 rev 1 17/43 6 connectors 6.1 jtag connector cn1 the cn1 connector allows to connect the stm32 microcontroller to a jtag cable. figure 7. jtag connector pinout 6.2 audio extension connector cn3 the cn3 connector allows to connect an steval-caa021v1 audio demonstration board. figure 8. i 2 s audio connector of the ts4657 audio card - schematic table 17. jtag connector signals pin signal pin signal pin signal pin signal 1 +3.3 v 6 gnd 11 jrtck 16 gnd 2 +3.3 v 7 jtms 12 gnd 17 dbgrq 3 jtrst 8 gnd 13 jtdo 18 gnd 4 gnd 9 jtck 14 gnd 19 dbgack 5 jtdi 10 gnd 15 jrst 20 gnd !- 6 $!#?3$!4 $!#?"#,+ $!#?-#,+ $!#?&-4 $!#?&-4 $!#?,2#,+ 34"9?2 34"9?, ' ' 30+?34"9 -)#2/?/54 -)#2/?3($. $!#?34"9 '.$ 0 6 ##! '.$ '.$! !-
connectors um0896 18/43 doc id 17009 rev 1 additional information can be found in the steval-caa021v1 user manual (um0722). 6.3 analog/digital mems extension connector cn6 and cn8 the cn6 and cn8 connectors allows to connect steval-mki0xxv1 mems demonstration boards (gyroscope, accelerometer) that are compatible with 24 dil socket. the mems extension must be fitted in both connectors cn6 and cd8 in the same time. the mems extension when plugged uses only the right half of the cn8 connector terminals. the left half is free even if the mems extension is plugged. figure 9. digital mems connector pinout table 18. description of the i 2 s audio connector pins of the ts4657 audio card pin signal pin signal pin signal pin signal 1 gnd 6 g1 gain select for ts2012 (pd3) 11 right channel mute for ts2012 (pd4) 16 data format selection fmt2 for ts4657 (pe2) 2 + 5 v 7 v cca +3.3 v supply voltage for microphone domain 12 ts4657 sdat i 2 s signal (pc12) (spi3mosi) 17 standby for ts4962 (on-board speaker and mono jack) (pd7) 3 microphone shutdown (pb2) 8 ts4657 lrclk i 2 s signal (pa15) (jtd) (i 2 s3_ws) 13 left channel mute for ts2012 (pd5) 18 data format selection fmt1 for ts4657 (pe1) 4 g0 gain select for ts2012 (pd2) 9 gnda ground for microphone domain 14 ts4657 mclk i 2 s signal (master clock) (pc7) (i 2 s3_mck) 19 gnd 5 analog output from microphone preamplifier (pb1) (adc12_in9) 10 ts4657 bclk i 2 s signal (pc10) (spi3_sck) 15 standby for ts4657 20 nc !- #. (eader (0 -)3/ -/3) 3$!?-%-3 3#+ 3#,?-%-3 #3?-%-3 0$ &3 3elf4est )nt )nt
um0896 connectors doc id 17009 rev 1 19/43 figure 10. gpio and analog connector pinout table 19. digital mems connector signals pin signal (mems) signal description 1 n. c. 2 hp high-pass filter reset, signal for gyroscope 3 spi 1 - miso 4 spi 1 - mosi shared with i 2 c 1 - sda 5 spi 1 - clk shared with i 2 c 1 - scl 6 cs_mems chip select for the spi 1 device 7 pd power-down of the device 8 fs full scale of the measured range 9 selftest 10 int2 interrupt request 11 int1 interrupt request 12 gnd !- 6 6 #. 0$ 0$ 0$ 0" 0" 0# 3#3 ?. 70rotect #3 ?7i &i /546outx /out x/6outy 6refmemsref x/6outz /54 out / (eaderx
connectors um0896 20/43 doc id 17009 rev 1 additional information can be found in the steval-mk10xxv1 user manual. 6.4 power line networking extension connector cn7 the connector cn7 is dedicated for the interconnection with st7590 ofdm prime compliant power line modem demonstration board through uart and spi. figure 11. connector cn7 for plm, usart and spi interface table 20. gpio and analog mems connector signals pin signal - the left half (gpio) pin signal - the right half (mems) 1 +3.3 v 2 +3.3 v 3 +3.3 v 4 +3.3 v 5 gpio (pd0) 6 nc 7 gpio (pd1) 8 x - axis, or gyro output-1 (pc0) (adc12_in10) 9 gpio (pd13) 10 nc 11 gpio (pb5) 12 y - axis (pc4) (adc12_in14) 13 gpio (pb9) 14 nc 15 gpio (pc8) 16 z - axis (pc5) (adc12_in15) 17 serial chip select from host (pc9) 18 nc 19 u9 wi-fi module-1 write protect (pc15) 20 nc 21 u9 wi-fi module-1 chip enable (pe15) 22 gyro output-2 (pb0) (adc12_in8) 23 gnd 24 nc table 21. connector cn7 for plm, usart and spi interface pin signal pin signal 1 usart_txd_lv+3v3 2 usart_rdx_lx 3 gnd 4 vcc_lv 5 miso_lv 6 sclk0_lv 7 mosi_lv 8 ssn0_lv !-
um0896 connectors doc id 17009 rev 1 21/43 signals xxxx_lv mean, t hat these signals operate up to vcc_lv voltage level. vcc_lv is connected to 3.3 v. 6.5 power test points these three testing points allow to measure the power supply voltage . table 22. test points 6.6 usb connector cn4 there is usb mini connector on the board. the terminal pin description is shown in ta b l e 2 3 . table 23. usb connector cn4 signals 9 rts_lv 10 cts_lv 11 mdm_resn_lv 12 dfu_force_lc 13 gnd 14 gnd table 21. connector cn7 for plm, usart and spi interface pin signal pin signal test point name signal description +3.3 v +3.3 v output from u3 linear voltage regulator for stm32, phy, wi-fi, mems and audio extension. +5.0 v +5.0 v output from u2 switching power supply for usb-otg, audio extension and u3. gnd ground pin signal description 1 usb_vbus 2 id otg identification of the device connected 3 usb-dp data plus signal 4 usb-dm data minus signal 5 gnd
connectors um0896 22/43 doc id 17009 rev 1 6.7 u10 wi-fi module-2 debugging signals txupd and rxupd these two testing points allow to update the firmware of the optional wi-fi module-2. 6.8 ethernet rj45 connectors cn5 figure 12. ethernet rj45 connectors cn5 - front view table 24. u10 wi-fi module-2 debugging signals txupd and rxupd signal signal description txupd uart tx update signal rxupd uart rx update signal table 25. rj45 connectors cn5 pin description pin description 1 txdata+ 2 txdata? 3 rxdata+ 4 nc 5 nc 6 rxdata? 7 nc 8 nc
um0896 connectors doc id 17009 rev 1 23/43 6.9 microsd card connector cn9 figure 13. microsd card connector cn9 table 26. microsd card connector cn9 pin description pin number description 1 nc 6 gnd 2 cs_sdcard (pe7) 7 miso (spi 1 - pa6) 3 mosi (spi 1 - pa7) 8 nc 4 +3.3 v 9 gnd 5 sck (spi 1 - pa5) 10 sd_detect (pa4)
connectors um0896 24/43 doc id 17009 rev 1 6.10 schematics figure 14. power supply n&? # n&? # 6 # 6 # 0owersuppl y 6 6 '.$ 6 ). 6 /54 6 /54 5 ,$3 ,$ 2e d 6 #. '-+! 6 ! 6 3403,5 $ !6 $ 34 3403,5 p& # # n& , tantal 6 #$% # /54 39.# %.) .( #/-0 6 ## '.$ &376 2%& &" '.$ 5 $ 343-4! 2 2 2 ./4% 6 # ceramic 6 .! 2 $ifferent frequency n& # 2 n& # 2 2 4erminalblock 0 3" !-
um0896 connectors doc id 17009 rev 1 25/43 figure 15. stm32 - part 1(inputs, outputs, clock, reset) 0% 0% 0% 0% 0% 0# !.4)?4!-0 0# /3#?). 0# /3#?/54 /3#?) . /3#?/54 .234 0# 0# 0# 0# 0! 7+ 50 0! 0! 0! 0! 0! 0! 0! 0# 0# 0" 0" 0" 0% 0% 0% 0% 0% 0% 0% 0% 0% 0" 0" 0" 0" 0" 0" 0$ 0$ 0$ 0$ 0$ 0$ 0$ 0$ 0# 0# 0# 0# 0! 0! 0! 0! 0! 0! .# 0! 0! 0# 0# 0# 0$ 0$ 0$ 0$ 0$ 0$ 0$ 0$ 0" 0" 0" 0" 0" "//4 0" 0" 0% 0% 5 ! 34-&?+ #3?7)& ) 0$ 0$ 0$ 48#,+ 48$? -$# 28$? 28$? 28$? 28$? 28$6 #23 -$) / #/ , 28%2 48$? 48%. 48$? 48$? 2%3%4 k? 2 "oot option 53"?$- 53"?$ 0 $!#?,2#, + $!#?"#, + $!#?3$!4 $!#?-#, + # p& #- 8 -(z -)#2/?/54 -)#2/?3($. 34"9?, 34"9?2 $!#?34" 9 30+?34" 9 ' ' ,% $ -# / #- 8 -(z *0 # p& 53"?0ower3witch/n 53"?) $ 53"?6"5 3 28#, +? -# 5 6out y 6out z 6out x out 53"?/ver#urrent *4$) ,% $ ,% $ ,% $ *4-3 *4#+ *4$/ #3?3$car d 3# + -)3 / -/3) 3$! #3?-%-3 0$ &3 3elf4es t (0 )n t )n t "4.?50 "4.?$7 "4.? , "4.? 2 "4.?#% 3# , 3$?detec t *4234 *234 70rotect &?!7!+ % ). 4?.8 3#3? . 0% 0% 3" *4234 *23 4 -$-?2%3 33. !-
connectors um0896 26/43 doc id 17009 rev 1 figure 16. stm32 - part 2 (jtag, leds, audio extension connector) !- $!#?3$!4 $!#?"#, + $!#?-#, + $!#?&-4 $!#?&-4 $!#?,2#, + 34"9?2 34"9?, ' ' 30+ ?34" 9 -) #2/?/54 -) #2/?3($. $!#?34" 9 #. (eader x 3 6 6 k? 2 k? 2 k? 2 *4!' 6 !udioconnector 4est points 6 6 6 6 ,$ '2%% . 6 ,$ 2% $ ,%$ ,%$ ,%$s '.$ '.$ 6 ,$ 9%,,/7 ,$ 9%,,/7 ,%$ ,%$ +? 2 6$$! ? 2 ? 2 ? 2 #. '- -,7' *4$) *4-3 *4#+ *24# + *4$/ *234 $"'2 1 $"'!# + 6 6 *4234
um0896 connectors doc id 17009 rev 1 27/43 figure 17. stm32 - part 3 (joystick, analog decoupling, dac_fmt signals) !- 2%3% 4 n&? # 2%3%4 2eset 6"!4 633? 6$$? 633! 62%& n 62%& 6$$! 633? 6$$? 633? 6$$? 633? 6$$? 633? 6$$? 5 " 34-&?+ , "%!$ # # n& 6$$! 62%& # n& 6 # n& # n& # n& # n& # n& 6 6 2? 2 $!#?&-4 $!#?&-4 n&? # ? 2 n&? # ? 2 n&? # ? 2 n&? # "4.?50 ? 2 up dw , 2 37 *oystick "4.?$7 "4.? 2 "4.? , "4.?#% "4.?50 "4.?$7 "4.? ," 4.?2 n&? # ? 2 "4.?#% # *0 *0 0%0 % 3$! 3# ,
connectors um0896 28/43 doc id 17009 rev 1 figure 18. ethernet - part 1 (phy pinout) -$# 28$? 28$? 48%. 48$? 48$? #2 3 -$) / 28$? 28$? 28$6 28%2 48#, + 48$? 48$? #/ , -# / 4$0? 4$.? 2$.? 2$0? 2 $6$$ $6$$ $6$$ 6##! 6##! 6##! 2%3%4 2 2 ,%$?,) .+!.?%.? !. ,%$?!#4!.? 2 2 48?#,+ ,0"+?%. 48?% . '.$! 6##! 48$ 48$ 48$3#, + 48$-))?#&' 072$7.-$).4 2%3%26%$ 2%3%26%$ '.$ 6##! 28. 280 '.$! 480 48. '.$! '.$! )2%& 6##! '.$! 6##! 3$0 ,%$?!#4!. ,%$?30%%$!. ,%$?,).+!.?%. 2%3% 4 -$) / -$# /6$$ '.$ 8 8 $6$$ 28?#,+ 28$6-))?#&' #2348$ 28%2228$ $6$$ 28$0(9!$$2 28$0(9!$$2 28$0(9!$$2 28$0(9!$$2 #/,0(9!$$2 '.$ 3$ . 5 3424 28#,+?0(9 $6$$ !-
um0896 connectors doc id 17009 rev 1 29/43 figure 19. ethernet - part 2 (overvoltage protection, phy configuration) 2 $6$$ 2 2 2 $6$$ 2 2 2 48#, + 28$6 48$? #/ , 28$? 28$? 28$? 28$? !$$ !$$ !$$ !$$ !$$ ,0"+ !. !. "oot strap -))address x -#/4 8$? 3" 28#, +? -#5 3" 2-)) -#/ 3" 28#, +? -# 5 28#, +? 0(9 fit fit remove -)) remove fit remove #& #& $6$$ $6$$ #& #& #& #& 6##! # n&? 4$0? 4$.? ) / 6"53 ) / ) / '.$ ) / 5 $6)5,# 0 6##! # n&? 2$0?#? 2$0? 2$.? ) / 6"53 ) / ) / '.$ ) / 5 $6)5,# 0 2$.?#? 4$0?#? 4$.?#? !-
connectors um0896 30/43 doc id 17009 rev 1 figure 20. ethernet - part 3 (magnetics) 6##! 2 2 $6$$ 2 2 ,%$?!#4!.? ,%$?,) .+!.?%.? 9ellow #4 4$ n 4$ 2$ n 2$ #4 'reen 48 48 n 28 28 n #. 0ulse * # n&6 6##! $6$$ 2 2$.?#? 2$0?#? 4$0?#? 4$.?#? n& # n& # n& # 2 # 6##! n& # n& # 2 # $6$$ 6 , -,3 3 , -,3 3 6##! $6$$ # n&? # n&? !-
um0896 connectors doc id 17009 rev 1 31/43 figure 21. usb-otg !6 low drop $ 343403,5 6 6 # 6"53 $- $0 )$ '.$ 3hield 53"?-ini!" receptacle #. 53" mini socket ) / '.$ ) / ) / 6"53 ) / 5 53",# 0 '.$ ). %. /54 &!5,4 5 34-03342 !6 3403 ,5 $ 2? 2 2? 2 +? 2 2? 2 2? 2 2? 2 2? 2 53"?0ower3witch/n 53"?6"5 3 53"?$- 53"?$ 0 53"?) $ 53"?/ver#urrent ,$ '2%% . 3" 6 6 6 !-
connectors um0896 32/43 doc id 17009 rev 1 figure 22. wi-fi module-1
um0896 connectors doc id 17009 rev 1 33/43 figure 23. wi-fi module-2 '.$ 6$$? '.$ 6$$? $.# $.# $.# $.# 2%3 6$$? '.$ '.$ #%?. *4!'?%. $.# 3#3? . 6$$? '.$ 5!24?28 5!24?48 '.$ 6$$? '.$ 6$$? 3$/
).4?.8 3# + 3$ ) '.$ *4!'?4$ / *4!'?4# + *4!'?4- 3 *4!'?4$ ) 234? . $.# *4!'?234. :'- :'- 5 :'- 6 6 #3?7)&) 3# + -)3/ -/3 ) 70rotect 2%3%4 ).4?.8 2 6 6 *0 *0 pinjumper resistor *4'2. 3#3?. *4'2 . '.$ *4'%. *4'% . 2 2 2 6 ).4?.8 -/3) 3# + pinjumper resistor !-
connectors um0896 34/43 doc id 17009 rev 1 figure 24. microsd card 6 6 -icro3$#ard 37 37 #. 0*3 3- 3& &or3-3&& 2 micro card detection #3?3$#ar d 3# + -/3 ) -)3/ 3$?detect !-
um0896 connectors doc id 17009 rev 1 35/43 figure 25. mems extension connectors #. (eader #. (eader x 6 6out x 6outy 6out z )n t #3?-%- 3 )n t &3 0$ 3elf4est (0 /54 x/ /54 / / x/ 6ref out -)3 / -/3) 3# + 0$ 0$ 70rotect 6 0$ #3?7)&) *0 *0 3$ ! 3$!?-%-3 53!24?28 3# , 3#,?-%-3 53!24?4 8 3#3? . 3$!?-%-3 3#,?-%-3 3$?detect #. (eader x -)3/ -/3 )#+ -$-?2%3 -$-?2% 3 6 dfu rts cts 33. 53!24?4 8 53!24?28 33. 4x$ 2x$ out memsref 2? 2 2? 2 out memsre f -)3 / -/3 ) !-
connectors um0896 36/43 doc id 17009 rev 1 6.11 power supply connectors cn2, p2 figure 26. power supply connector cn2 figure 27. power supply connector p2 table 27. power supply connector cn2 pin signal pin signal 1 24 v dc 3 gnd 2gnd table 28. power supply connector p2 pin signal 1 24 v dc 2gnd !)6 !)6
um0896 evaluation software doc id 17009 rev 1 37/43 7 evaluation software the stm32f107xx connectivity gateway is delivered with software evaluation package including the demonstration applications and libraries in c source code. the package includes: connectivity gateway demonstration application - usb audio card, tcp/ip demonstration based on lwip stack: dhcp cl ient, telnet server, webserver, tftp server utilizing microsd card, server/clients application example applications: ? audio streaming application - usb audio card - see um0722 ? webserver based on uip tcp/ip stack - see um0819 ? mems usb bridge application showing mems data on pc - see um0701. 7.1 connectivity gateway demonstration application (cg demonstration) the ?cg demonstration? demonstrates the audio and ethernet c apabilities of t he board. it also demonstrates the mems sensor data acquisition feature. to run the cg demonstration properly, the steval-pcc012v1 and steval-cca021v1 must be interconnected. to perform mems sensor data acquisition, one of the compatible steval-mki0xxv1 boards should be connected. the cg demonstration consists of two parts: the audio and the ethernet demonstration. after reset the ip address is resolved using dhcp client, and leds are toggled until this process is completed. the audio part demonstration reproduces the board ip address. it is then reprogrammed to play sounds coming through the usb interface, making the board behave as an usb audio card. the ethernet demonstrations are based on lwip tcp/ip stack and consist of: dhcp client, for ip address setting hello example based on the telnet protocol tftp server, which transfers files from and to the microsd card inserted in cn9 connector. web server showing pages with pictures and also data acquired from mems sensor server/clients example, which uses multiple boards and allows clients to control the server's leds. the ethernet demonstrations are described in details in application note an3102. the description is also valid for the cg demonstration except for small modifications related to server/clients example. here the server is selected at startup by keeping the joystick button pressed. the selected function of the board is shown by leds after the ip address is resolved as shown by ta ble 2 9 . the position of joystick on the client board controls leds on the server board.
evaluation software um0896 38/43 doc id 17009 rev 1 figure 28. connectivity gateway webserver demonstration table 29. board function indication after reset for server/clients example function led1 led2 led3 led4 static ip off off off on client off off on on serveroffononon
um0896 bom of the board doc id 17009 rev 1 39/43 8 bom of the board table 30. bill of material designator value comment ld1, ld3 smd 0805 led yellow ld2, ld5 smd 0805 led red ld4, ld6 smd 0805 led green d4 protection diode sm6t33a reset button sw-pb sb4 soldering bridge soldbridge d1, d2, d3, d5 stps3l40u st: stps3l40u cn5 ethernet transformer con. j00-0086 r11, r14, r16, r18, r19, r20, r21, r22, r23, r48 10 k 10k_0603 r17 470 470r_0603 r2 47 47r_0603 r24, r25, r32 0 0r_0603 r26 300 300r_0603 r28, r30 22 22r_0603 r3 2.2 k 2k2_0603 r5, r9, r15 680 680_0603 c15, c16 10 f / 16 v 10 f / 16 v c26 47 f 10 f c4 47 f 100 f c5 10 f 10 f u3 3.3 v voltage regulator ld1117s33 cn2 power connector k375a l1 inductor 100 h bead l2 inductor 33 h mss1260-333 cn8 male connector dual in line header 12 x 2 cn6 male connector single in line header 12 cn3 female connector dual in line header 10 x 2 s p2 terminal block terminal block cn1 male connector with key jtag r10 47 k 47 k r12, r13 5.6 k , 91 k 1.28 k
bom of the board um0896 40/43 doc id 17009 rev 1 r27, r29, r31, r33, r34, r35, r36, r37, r38, r39, r40, r41, r42, r43, r44, r45, r46, r47, r49, r50, r51, r52, r53, r54, r55, r56, r57, r58, r59 1.2 k , 1 m , 2 k , 2.2 k , 4.7 k , 5.6 k , 10 k , 22 k , 91 k , 100 k , 220 r4 n. a. (102 k ) n. a. (102 k ) r7 10 k 10 k r8 100 100 c30, c31, c32, c34, c35, c42 100 nf c33, c36, c43 10 f / x5r u10 wi-fi module g2m5477 u5, u6 ethernet voltage protection dviulc6-2p6 x1 crystal resonator 14.7456mhz x2 crystal resonator 25 mhz c1, c6, c8, c10, c11, c12, c13, c14, c41 capacitor 10 nf c17, c18 100 nf footprint 100n_0805 c19, c21, c22, c23, c24, c40 100 nf footprint 100 nf_0603 c2 10 f / ceramic / 35 v 10 f ceramic / 35 v c20, c25 12 pf c27, c28 100 nf c29 10 nf / 500 v c3 470 nf 470 nf c38, c39 100 nf c7 47 pf 47 pf c9 1 nf 1 nf u8 st802rt1 jp4, jp5 3-pin jumper resistor 4.7 k jp1, jp2, jp3 3-pin jumper resistor 3v3 +3.3 v 5v0 +5.0 v cn4 565790576 cn9 pjs008-2000 ddd1 st_logo ddd2, ddd4 roh1 ddd3 roh2 gnd gnd hole1, hole2, hole3, hole4 distance hole table 30. bill of material (continued) designator value comment
um0896 bom of the board doc id 17009 rev 1 41/43 l3, l4 mls0805-4s4-300 rxupd, txupd update sw1 joystick u1 stm32f107vct6_256k u2 l5973d st:l5973d u4 stmps2141str u7 usblc6-2p6 u9 zg2100m table 30. bill of material (continued) designator value comment
revision history um0896 42/43 doc id 17009 rev 1 9 revision history table 31. document revision history date revision changes 12-mar-2010 1 initial release.
um0896 doc id 17009 rev 1 43/43 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at an y time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a particular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by an authorized st representative, st products are not recommended, authorized or warranted for use in military, air craft, space, life saving, or life sustaining applications, nor in products or systems where failure or malfunction may result in personal injury, death, or severe property or environmental damage. st products which are not specified as "automotive grade" may only be used in automotive applications at user?s own risk. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2010 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of EVL6563S-400W

	To Download EVL6563S-400W Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .