embedded power for business-critical continuity aif series 600 watts special features ? 600w continuous power at 100c baseplate temperature ? 108w/in 3 (6.6w/cm 3 ) ? high efficiency - up to 90% ? low output ripple and noise ? positive and negative enable function ? excellent transient response ? ovp, ocp, v adj control with alp tm analog mode linear control, or through i 2 c bus with digital mode control. ? paralleable with accurate current sharing ? eu directive 2002/95/ec compliant for rohs total power: 600 watts (12v@50amps) input voltage: 300v # of outputs: single electrical specifications safety input input ra nge 250 - 420 vdc input surge 450v / 100ms efficiency 90%@5.0v (typical) output load regulation 0.2% typical down to no load line regulation 0.2% typical noise / ripple 100mv typical (below 5v); 2% typical (5v and above) remote sense up to 0.5v output voltage adjust range +/-20% for 5v and above; +10%/ -50% for below 5v transient response 5% max for 3.3v and above, 150mv for 1.8v, deviation with 25% to 75% full load 250 s (max) recovery current share accuracy 3% typical overvoltage protection 115% vo (nominal) current limit 115% io maximum control voltage adjust 80 to 120% vo linear programming for 12v, 15v, 24v, 48v 50% to 110% for 1.8v - 5.0v enable ttl compatible (positive & negative enable options) current limit adjust 20 to 100% io linear programming or digital mode control clock input (external sync) 3.3 to 5.5vp-p @ 800khz 10% clock output (internal clock) 4.5vp-p typical@ 800khz 5% power good identification high (vo) = power good temperature monitor output 10mv/k (2.73 = 0c) current monitor output 0 to 1ma (1ma = 100% i o rated ) over voltage protection adjust 110 to 150% vo linear programming by voltage or resistor, or digital mode control notes nominal values apply with sense pins connected and other control pin unconnected. alp: astec linear programming ul 60950 recognized cul 60950 recognized tuv en60950 licensed ce ce mark rev. 05.23.07 aif series 1 of 2 rohs
emerson network power and the emerson network power logo are trademarks and service marks of emerson electric co. ?2005 emerson electric co. embedded power for business-critical continuity emerson network power. the global leader in enabling business-critical continuity. emersonnetworkpower. com ac power connectivity dc power embedded power inbound power integrated cabinet solutions outside plant precision cooling site monitoring and services pin assignments input (ac) output (dc) control pins 31. positive 21. positive 1. +sense 32. negative 22. positive 2. temp mon 23. positive 3. c mon 24. positive 4. c share 25. negative 5. clk out 26. negative 6. clk in 27. negative 7. pg/id 28. negative 8. c lim adj 9. ovp adj 10. v adj 11. enable 12. -sense mechanical drawing americas 5810 van allen way carlsbad, ca 92008 usa telephone: +1 760 930 4600 facsimile: +1 760 930 0698 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom telephone: +44 (0) 1384 842 211 facsimile: +44 (0) 1384 843 355 asia (hk) 16th - 17th floors, lu plaza 2 wing yip street, kwun tong kowloon, hong kong telephone: +852 2176 3333 facsimile: +852 2176 3888 for global contact, visit: www.astecpower.com www.artesyn.com technicalsupport@astec.com technicalsupport@artesyn.com while every precaution has been taken to ensure accuracy and completeness in this literature, emerson network power assumes no responsibility, and dis- claims all liability for damages resulting from use of this information or for any errors or omissions. operating temperature -20c to +100c (case temperature) start up temperature -40c to +100c (case temperature) storage temperature -40c to +125c overtemperature protection 110c max environmental specifications ordering information input voltage output voltage efficiency model number 300v 1.8v @ 120a 80% (typ) aif120y300 300v 3.3v @ 120a 87% (typ) AIF120F300 300v 5.0v @ 80a 90% (typ) aif80a300 300v 12v @ 50a 90% (typ) aif50b300 300v 15v @ 40a 90% (typ) aif40c300 300v 24v @ 25a 90% (typ) aif25h300 1. for negative enable, add suffix -n. 2. for non-thread hole, add suffix -nt. 3. for rohs 6, add suffix -l. default is rohs 5. rev. 05.23.07 aif series 2 of 2
|
