95 subminiature basic switch ssg subminiature basic switch conforming to en61058-1 (iec1058-1), ul1054, and csa c22.2 no.54 a wide operating temperature range of 25 c to 125 c is available for at high-temperature use. a wide variety of terminals: solder, tab (#110), and pcb terminal models. pcb t erminal models are resistant to flux. ordering information actuator rating of max. solder (see note) t ab (#1 10) pcb (see note) pin plunger 0.1 a 1.50 n ssg-01h ssg-01t ssg-01p pu ge 0.50 n ssg-01h-5 ssg-01t-5 ssg-01p-5 5 a 1.50 n ssg-5h SSG-5T ssg-5p 0.50 n ssg-5h-5 SSG-5T-5 ssg-5p-5 hinge lever 0.1 a 0.60 n ssg-01l1h ssg-01l1t ssg-01l1p geee 0.20 n ssg-01l1h-5 ssg-01l1t-5 ssg-01l1p-5 5 a 0.60 n ssg-5l1h ssg-5l1t ssg-5l1p 0.20 n ssg-5l1h-5 ssg-5l1t-5 ssg-5l1p-5 simulated hinge lever 0.1 a 0.60 n ssg-01l3h ssg-01l3t ssg-01l3p s uaed geee 0.20 n ssg-01l3h-5 ssg-01l3t-5 ssg-01l3p-5 5 a 0.60 n ssg-5l3h ssg-5l3t ssg-5l3p 0.20 n ssg-5l3h-5 ssg-5l3t-5 ssg-5l3p-5 hinge roller lever 0.1 a 0.60 n ssg-01l2h ssg-01l2t ssg-01l2p ge oe ee 0.20 n ssg-01l2h-5 ssg-01l2t-5 ssg-01l2p-5 5 a 0.60 n ssg-5l2h ssg-5l2t ssg-5l2p 0.20 n ssg-5l2h-5 ssg-5l2t-5 ssg-5l2p-5 note: en61058-1 (iec1058-1) approved by tv rheinland.
ssg ssg 96 specifications ratings 1. general ratings non-inductive load inductive laod resistive load lamp load inductive load motor load rated voltage nc no nc no nc no nc no 125 v ac 5 (0.1) a (see note 1) 1.5 a 0.7 a 3 a 2.5 a 1.3 a 250 v ac 3 a 1 a 0.5 a 2 a 1.5 a 0.8 a 8 vdc 5 a 2 a 5 a 3 a 14 vdc 5 a 2 a 4 a 3 a 30 vdc 4 (0.1) a (see note 1) 2 a 3 a 3 a 125 vdc 0.4 a 0.05 a 0.4 a 0.05 a 250 vdc 0.2 a 0.03 a 0.2 a 0.05 a note: 1. the values in the parentheses are for the ssg-01. 2. the above current ratings are the values of the steady-state current. 3. inductive load has a power factor of 0.7 min. (ac) and a time constant of 7 ms max. (dc). 4. lamp load has an inrush current of 10 times the steady-state current. 5. motor load has an inrush current of 6 times the steady-state current. 6. if the switch is used in a dc circuit and is subjected to a surge current, connect a surge suppressor across the switch. 2. tv rheinland approved rating (en61058-1/iec1058-1) ssg-5 series: 5 a at 250 v ac (t125, 50,000 operations) ssg-01 series: 0.1 a at 30 vdc (t125, 50,000 operations) 3. ul, csa approved rating ssg-5 series: 5 a at 125 v ac, 3 a at 250 vac (6,000 operations) ssg-01 series: 0.1 a at 125 v ac, 0.1 a at 30 vdc (6,000 operations) characteristics operating speed 0.1 mm to 1 m/s (at pin plunger) operating frequency mechanical: 400 operations/min electrical: 60 operations/min insulation resistance 100 m w min. contact resistance of 1.50 n: ssg-5 series: 30 m w max. ssg-01 series: 50 m w max. of 0.50 n ssg-5 series: 50 m w max. ssg-01 series: 100 m w max. dielectric strength 1,000 v ac, 50/60 hz for 1 min between contacts of the same polarity (600 v ac for ssg-01h and ssg-01t series) 1,500 v ac, 50/60 hz for 1 min between each terminal and ground 1,500 v ac, 50/60 hz for 1 min between each terminal and non-current-carrying metal part inrush current ssg-5: no: 20 a max. nc: 10 a max. ssg01: no: 1 a max. nc: 1 a max. v ibration resistance malfunction: 10 to 2,000 hz, 196 m/s 2 (20g) (contact open: 10 m s max., lever position: at ttp) shock resistance malfunction: 490 m/s 2 (approx. 50g) (contact open: 10 m s max., lever position: at ttp) life expectancy mechanical: 10,000,000 operations min. (ot : rated value) electrical: 200,000 operations min. (5 a at 125 v ac for ssg-5, 0.1 a at 125 v ac for ssg-01, resistive ot:full) degree of protection (ip code) ip00 (iec1058-1) degree of protection against electrical shock class i (iec1058-1) proof tracking index 175 v (iec1058-1) switch category (iec335-1) d (iec1058-1)
ssg ssg 97 contact item ssg-5 ssg-01 specification rivet crossbar material silver pgs alloy safety standards certification body standard file no. tv rheinland en61058-1 (iec1058-1) t9451449 ul ul1054 e32667 csa c22.2 no.54 lr21642 operating characteristics solder/tab terminal type pin plunger hinge lever simulated hinge lever hinge roller lever ssg-01 ssg-5 ssg-01 -5 ssg-5 -5 ssg-01l1 ssg-5l1 ssg-01l1 -5 ssg-5l1 -5 ssg-01l3 ssg-5l3 ssg-01l3 -5 ssg-5l3 -5 ssg-01l2 ssg-5l2 ssg-01l2 -5 ssg-5l2 -5 of max. 1.50 n (153 gf) 0.50 n (51 gf) 0.60 n (61 gf) 0.20 n (20 gf) 0.60 n (61 gf) 0.20 n (20 gf) 0.60 n (61 gf) 0.20 n (20 gf) rf min. 0.25 n (25 gf) 0.04 n (4 gf) 0.06 n (6 gf) 0.02 n (2 gf) 0.06 n (6 gf) 0.02 n (2 gf) 0.06 n (6 gf) 0.02 n (2 gf) pt max. 0.6 mm 1.0 mm 1.0 mm 1.0 mm ot min. 0.4 mm 0.8 mm 0.8 mm 0.8 mm md max. 0.1 mm --- --- --- fp max. --- 13.6 mm 15.5 mm 19.0 mm op 8.4 0.3 mm 8.8 +1.0 / 0.6 mm 10.7 +1.0 / 0.6 mm 14.5 +1.0 / 0.6 mm pcb terminal type pin plunger hinge lever simulated hinge lever hinge roller lever ssg-01p ssg-5p ssg-01p-5 ssg-5p-5 ssg-01l1p ssg-5l1p ssg-01l1p-5 ssg-5l1p-5 ssg-01l3p ssg-5l3p ssg-01l3p-5 ssg-5l3p-5 ssg-01l2p ssg-5l2p ssg-01l2p-5 ssg-5l2p-5 of max. 1.50 n (153 gf) 0.50 n (51 gf) 0.60 n (61 gf) 0.20 n (20 gf) 0.60 n (61 gf) 0.20 n (20 gf) 0.60 n (61 gf) 0.20 n (20 gf) rf min. 0.25 n (25 gf) 0.04 n (4 gf) 0.06 n (6 gf) 0.02 n (2 gf) 0.06 n (6 gf) 0.02 n (2 gf) 0.06 n (6 gf) 0.02 n (2 gf) pt max. 0.6 mm 1.0 mm 1.0 mm 1.0 mm ot min. 0.4 mm 0.8 mm 0.8 mm 0.8 mm md max. 0.1 mm --- --- --- fp max. --- 17.0 mm 18.9 mm 22.4 mm op 11.8 0.4 mm 12.2 +1.1 / 0.7 mm 14.4 +1.1 / 0.7 mm 17.9 +1.1 / 0.7 mm
ssg ssg 98 dimensions note: 1. all units are in millimeters unless otherwise indicated. 2. every actual model number includes the code instead of for the kind of terminals incorporated by the model. 3. unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. terminal model solder/tab terminal pin plunger ssg-01 ssg-5 ssg-01 -5 ssg-5 -5 2.2 +0.1 0 1.8 7.5 0.3 2.2 2.5 dia. 5.1 8.9 (see note) 7.2 (see note) 9.5 0.1 0.5 6.9 7.7 3.5 3.2 6.4 0.2 three, 1.6 dia. holes note: at switch bottom 6.1 19.8 2.2 +0.1 0 dia. hole cnonc 1.6 (see note) pt op hinge lever ssg-01l1 ssg-5l1 ssg-01l1 -5 ssg-5l1 -5 simulated hinge lever ssg-01l3 ssg-5l3 ssg-01l3 -5 ssg-51l3 -5 8.9 (see note) 6.9 5.3 0.4 6.9 7.7 t0.3 stainless lever 2.2 +0.1 0 3.6 6.1 2.2 5.1 2.5 dia. 7.2 (see note) 0.5 note: at switch bottom 9.5 0.1 2.2 +0.1 0 dia. hole 3.2 6.4+0.2 three, 1.6 dia. holes cnonc 3.2 6.4 0.2 three, 1.6 dia. holes 7.7 6.1 2.2 19.8 5.1 2.5 dia. t0.3 stainless lever 0.5 note: at switch bottom 9.5 0.1 3.6 2.2 +0.1 0 dia. hole r 1.3 6.3 0.4 19.8 cnonc 8.9 (see note) 7.2 (see note) 1.6 (see note) 2.2 +0.1 0 1.6 (see note) op fp op fp
ssg ssg 99 hinge roller lever ssg-01l2 ssg-5l2 ssg-01l2 -5 ssg-5l2 -5 3.8 5 0.4 6.9 7.7 6.1 2.2 3.2 6.4 0.2 19.8 5.1 2.5 dia. t0.3 stainless lever 0.5 note: at switch bottom 4.8 3.2 dia. acetal resin roller 9.5 0.1 2.2 +0.1 0 three, 1.6 dia. holes cnonc 8.9 (see note) 7.2 (see note) 1.6 (see note) 2.2 +0.1 0 dia. hole op fp pcb terminal pin plunger ssg-01p ssg-5p ssg-01p-5 ssg-5p-5 hinge lever ssg-01l1p ssg-5l1p ssg-01l1p-5 ssg-5l1p-5 c 1.3 0.3 0.5 0.05 6.4 0.2 2.87 0.1 4.8 0.3 3.4 0.1 2.5 dia. 5.15 7.62 0.2 1.8 7.62 0.2 3.5 4 0.3 1.8 three, 1.2 0.1 three, 0.8 7.7 nc no 2.2 +0.1 0 19.8 6.9 2.2 +0.1 0 dia. hole 9.5 0.1 pt op 6.9 5.3 0.4 19.8 5.15 2.5 dia. t0.3 stainless lever 7.62 0.2 3.4 0.1 2.2 +0.1 0 2.87 0.1 9.5 0.1 7.62 0.2 three, 0.8 three, 1.2 0.1 cnc no 1.3 0.3 0.5 0.05 6.4 0.2 4 0.3 3.6 7.7 2.2 +0.1 0 dia. hole 1.8 op fp
ssg ssg 100 simulated hinge lever ssg-01l3p ssg-5l3p ssg-01l3p-5 ssg-51l3p-5 2.2 +0.1 0 dia. hole 6.9 three, 1.2 0.1 t0.3 stainless lever r 1.3 6.3 0.4 7.7 19.8 5.15 2.5 dia. 7.62 0.2 3.4 0.1 2.2 +0.1 0 2.87 0.1 9.5 0.1 7.62 0.2 three, 0.8 no 1.3 0.3 0.5 0.05 6.4 0.2 1.8 4 0.3 3.6 cnc op fp hinge roller lever ssg-01l2p ssg-5l2p ssg-01l2p-5 ssg-5l2p-5 three, 1.2 0.1 6.9 no 4.8 3.2 dia. acetal resin roller 1.3 0.3 0.5 0.05 6.4 0.2 1.8 4 0.3 5 0.4 19.8 5.15 2.5 dia. t0.3 stainless lever 7.62 0.2 3.4 0.1 2.87 0.1 9.5 0.1 7.62 0.2 three, 0.8 c nc 2.2 +0.1 0 three, 1.2 0.1 3.8 2.2 +0.1 0 dia. hole op fp 7.7
ssg ssg 101 kind of terminals solder terminals tab terminals (#110) pcb terminals pcb mounting 2.2 +0.1 0 1.8 7.5 0.3 2.2 2.5 dia. 5.1 8.9 (see note) 7.2 (see note) 9.5 0.1 0.5 6.9 7.7 3.5 3.2 6.4 0.2 three, 1.6 dia. holes note: at switch bottom 6.1 19.8 2.2 +0.1 0 dia. hole cnonc 1.6 (see note) pt op 2.2 +0.1 0 1.8 7.5 0.3 2.2 2.5 dia. 5.1 9.5 0.1 0.5 19.8 6.9 7.7 3.5 3.2 6.4 0.2 three, 1.2 dia. holes note: at switch bottom 2.8 0.2 10.6 no nc 7.2 (see note) 7.1 2.2 +0.1 0 dia. hole 8.9 (see note) 1.6 (see note) c pt op 2.78 0.1 c 1.3 0.3 0.5 0.05 6.4 0.2 2.87 0.1 4.8 0.3 3.4 0.1 2.5 dia. 5.15 7.62 0.2 1.8 7.62 0.2 3.5 4 0.3 1.8 three, 1.2 0.1 three, 0.8 7.7 nc no 7.62 0.1 9.5 0.1 three, 1.35 dia. to 1.5 dia. 2.2 +0.1 0 19.8 6.9 15.24 0.1 2.2 +0.1 0 dia. hole 9.5 0.1 pt op
ssg ssg 102 precautions mounting use two 2.2 mounting screws with spring washers to mount the switch. tighten the screws to a torque of 0.20 to 0.25 n m (2 to 2.5 kgf cm). mounting holes 9.5 0.1 the switch does not have a ground terminal. the minimum distance through insulation (iec1058-1) is 0.9 mm. if proper insulation for the end product cannot be secured, additional insulation such as a sep - arator or insulation cover should be attached. soldering when soldering switch terminals, apply a soldering iron rated at 60 w max. and finish soldering quickly within 3 seconds. during sol - dering and 1 minute after soldering, do not apply external force to the terminals. solder terminal is provided with a hole so that a conductor can be secured mechanically . the conductors for a soldering terminal (h type) should be flexible and its cross section should be a wg18 to 20 for the ssg-5h series and a wg20 to 22 for the ssg-01h series. to automatically solder the switch to a pcb in a soldering bath, com - plete soldering within 5 seconds at a flux temperature of 250 c and avoid the overflow of flux onto the surface of the pcb where the switch or other parts are mounted. actuating make sure that the operating speed and frequency are within the permissible range of the switch. 1. do not use the switch in an application where the operating speed is extremely slow or the switching operation could become unstable or malfunctioning could result due to contact failure or contact welding. 2. do not use the switch in an application where the operating speed is too fast, or the switch will be broken due to a shock or the movable contact will not keep up with the speed. the reliability of a switch is maintained within the permissible oper - ating speed and frequency of the switch. the life of a switch is deter - mined at a specified operating speed, therefore, it varies with the ac - tual operating speed and frequency . the switch should be set so that its stroke will be in the range of 60% to 90% of the rated ot when the switch is operated. the stroke must not exceed the rated ot value. malfunctioning can result if the switch is set with its stroke exceed - ing the rated ot . therefore the proper adjustment of the mounting position is essential when installing the switch. do not apply excessive force to the actuator . be very careful not to apply force in the opposite and lateral directions relative to the oper - ating direction. all dimensions shown are in millimeters. to convert millimeters into inches, multiply by 0.03937. t o convert grams into ounces, multiply by 0.03527. cat. no. b096-e1-1
|
