MNR15 r e s i s t o r s rev.b 1/4 chip resistor networks MNR15 (0603 5 size) z f eatu r es 1) suit able for pull-up and pull-dow n resistors. 2) no direction to be mounted by placing common electrode w i th sy mmetry . 3) convex electrodes easy to check the fillet af ter soldering is finished. 4) high-density mounting can be mounted even densely than eight 0402chip s (mcr01), and mounting cost s are low e r . 5) comp atible w i th a w i de range of mounting machines. squared corners make it excellent for mounting using image recognition machines. 6) ro hm resistors have appr oved iso - 9001 certification. d e s i gn a n d sp ec ific at io ns ar e s u b j ect to c h a n g e w i t h o u t n o tic e . ca ref u ll y c h e ck the s p ecif ic ati o n sh e e t su p p l i e d w i th the product before using or ordering it. z ra tings item conditions specifications 0.031w (1 / 32w) rated power rated voltage operating temperature nominal resistance power must be derated according to the power derating curve in figure 1 when ambient temperature exceeds 70 c. ? 55 c to + 125 c at 70 c limiting element voltage 12.5 v the voltage rating is calculated by the following equation. if the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. e : rated voltage (v) p : rated power (w) r : nominal resistance ( ? ) e = p r 0 20 40 60 80 100 ? 55 0 7 0 100 125 ambient temperature ( c) power load (%) fig.1 see table 1. j ( 5%) 56 r 100k (e24) 200 table 1 resistance tolerance resistance range ( ? ) resistance temperature coefficient (ppm / c ) ? before using components in circuits where they will be exposed to transients such as pulse loads(short-duration, high-level loa ds), be certain to evaluate the component in the mounted state. in addition, the reliability and performance of this component ca nnot b e guaranteed if it is used with a steady state voltage that is greater than its rated voltage.
MNR15 r e s i s t o r s rev.b 2/4 z ch aracteristics item test conditions (jis c 5201-1) resistor type guaranteed value resistance variation of resistance with temperature solderability damp heat, steady state endurance at 70 c endurance rapid change of temperature bend strength of the end face plating resistance to solvent resistance to soldering heat overload (2.0% + 0.1 ? ) (1.0% + 0.05 ? ) (3.0% + 0.1 ? ) j : 5% no remarkable abnormality on the appearance. a new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. without mechanical damage such as breaks. jis c 5201-1 4.5 jis c 5201-1 4.8 measurement : + 25 / + 125 c jis c 5201-1 4.18 soldering condition : 260 5 c duration of immersion : 10 1s. jis c 5201-1 4.24 40 c, 93%rh test time : 1,000h to 1,048h (3.0% + 0.1 ? ) (3.0% + 0.1 ? ) (1.0% + 0.05 ? ) (1.0% + 0.05 ? ) (1.0% + 0.05 ? ) jis c 5201-1 4.25.1 rated voltage, 70 c 1.5h : on ? 0.5h : off test time : 1,000h to 1,048h jis c 5201-1 4.25.3 125 c test time : 1,000h to 1,048h jis c 5201-1 4.29 23 5 c , immersion cleaning, 5 0.5mi n. solvent : 2-propanol jis c 5201-1 4.19 test temp. : ? 55 c to + 125 c 5cyc jis c 5201-1 4.33 jis c 5201-1 4.17 rosinethanol (25%wt) soldering condition : 235 5 c duration of immersion : 2.0 0.5s. jis c 5201-1 4.13 rated voltage 2.5, 2s. maximum overload voltage : 25v see table.1 z ex te r n a l dime ns ions (unit : mm) material no. thick dielectric glaze of oxide metal thick film of silver for electrode nickel-coated electrode external electrode coated with sn alumina substrate overcoating (resin) 1 1 cross sectionb ? b' maqnification cross section a ? a' 3.2 0.1 ?? ? ? ? 0.64 1.6 0.1 0.3 0.1 0.35 0.1 0.5 0.1 b a a : 0.48 0.15 b : 0.32 0.15 b b b' a' a ? pitch of the upper electrode.
MNR15 r e s i s t o r s rev.b 3/4 z equiv a le nt c i rc uit r1 = r2 = r3 = r4 = r5 = r6 = r7 = r8 r4 r3 r8 r2 r7 r1 r6 r5 z packag in g 0 2 0 4 0 6 0 8 0 2 0 4 0 6 0 8 c ab d label ab c d reel taping p 0 p 2 p 1 a 0 e f w t2 d 0 chip network resistors eiaj et-7200b compliant thick paper mount (underside paper tape) square punchout hole heat crimp cover / tape b 0 (unit: mm) (unit : mm) f p 0 3.5 0.05 4.0 0.1 e p 1 1.75 0.1 4.0 0.1 a 0 p 2 1.8 0.1 2.0 0.05 b 0 t 2 3.4 0.1 max. 1.1 w d 0 8.0 0.3 1 0 1 1 0 1 1 0 1 1 0 1 180 0 ? 1.5 60 + 1 0 9 + 1.0 0 13 0.2 1.5 +0.1 0 z pr oduc t de s i gna tion n mr 1 r e0 j resistance tolerance part no. nominal resistance 5 p e0rp 5 , 000 MNR15 paper tape (4mm pitch) 180mm (7in.) j is also used for jumper j 5% resistance code,3 digits, 000 denotes jumper type. p ackaging specifications code part no. resistance tolerance j ( 5% ) code packaging specifications reel basic ordering unit (pcs) reel ( 180) : jeita et-7200b : standard product
MNR15 r e s i s t o r s rev.b 4/4 z electrical ch aracteristics resistance ( ? ) dc resistance (%) fig.2 resistance ? 6.0 ? 5.0 ? 4.0 ? 3.0 ? 2.0 ? 1.0 0 2.0 1.0 4.0 3.0 6.0 5.0 56 100 1k 10k 100k jis c 5201-1 4.5 sample size : n = 24pcs 20 c 65%rh ? 400 ? 300 ? 200 ? 100 0 100 200 300 400 resistance ( ? ) temperature coeficient (ppm/ c) jis c 5201-1 4.8 sample size : n = 24pcs 25 c / 125 c 56 100 1k 10k 100k fig.3 vatiation resistance with temperature resistance ( ? ) ? r/r (%) fig.4 overload ? 4.0 ? 3.0 ? 6.0 ? 5.0 ? 2.0 ? 1.0 0 2.0 3.0 1.0 4.0 5.0 6.0 56 100 1k 10k 100k jis c 5201-1 4.13 sample size : n = 24pcs rated voltage 2.5times 2s maximum overload voltage : 25v resistance ( ? ) ? r/r (%) fig.5 resistance to soldering hea t ? 2.0 ? 3.0 ? 1.0 0 1.0 2.0 3.0 56 100 1k 10k 100k jis c 5201-1 4.18 sample size : n = 24pcs soldering condition : 260 c 10s resistance ( ? ) ? r/r (%) fig.6 rapid change of temperatur e ? 2.0 ? 3.0 ? 1.0 0 1.0 2.0 3.0 56 100 1k 10k 100k jis c 5201-1 4.19 sample size : n = 24pcs ? 55 c / 125 c 5cyc resistance ( ? ) ? r/r (%) fig.7 damp heat, steady state ? 4.0 ? 3.0 ? 5.0 ? 6.0 ? 2.0 ? 1.0 0 2.0 1.0 3.0 4.0 5.0 6.0 56 100 1k 10k 100k jis c 5201-1 4.24 sample size : n = 24pcs 40 c 93%rh with no load 1000h resistance ( ? ) ? r/r (%) fig.8 endurance at 70 c ? 4.0 ? 5.0 ? 3.0 ? 6.0 ? 2.0 ? 1.0 0 2.0 1.0 3.0 4.0 5.0 6.0 56 100 1k 10k 100k jis c 5201-1 4.25.1 sample size : n = 24pcs 70 c 1,000h overload : the rated voltage resistance ( ? ) ? r/r (%) fig.9 endurance ? 4.0 ? 5.0 ? 3.0 ? 6.0 ? 2.0 ? 1.0 0 2.0 1.0 3.0 4.0 5.0 6.0 56 100 1k 10k 100 k jis c 5201-1 4.25.3 sample size : n = 24pcs 125 c with no load 1,000h
appendix appendix1-rev1.1 the products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. notes no technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of rohm co.,ltd. the contents described herein are subject to change without notice. the specifications for the product described in this document are for reference only. upon actual use, therefore, please request that specifications to be separately delivered. application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. rohm co.,ltd. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by rohm co., ltd. is granted to any such buyer. products listed in this document are no antiradiation design. about export control order in japan products described herein are the objects of controlled goods in annex 1 (item 16) of export trade control order in japan. in case of export from japan, please confirm if it applies to "objective" criteria or an "informed" (by miti clause) on the basis of "catch all controls for non-proliferation of weapons of mass destruction.
|
