View SPEAR-09-H022_1126130.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

preliminary data this is preliminary information on a new product now in development or undergoing evaluation. details are subject to change without notice. rev 2 december 2005 1/55 55 SPEAR-09-H022 spear? head arm 926, 200k customizable easic? gates, large ip portfolio soc features arm926ej-s - f max 266 mhz, 32 ki - 16 kd cache, 8 ki - kd tcm, etm9 and jtag interfaces 200k customizable equivalent asic gates (16k lut equivalent) with 8 channels internal dma high speed accelerator function and 112 dedicated general purpose i/os multilayer amba 2.0 compliant bus with f max 133 mhz programmable internal clock generator with enhanced pll function, specially optimized for e.m.i. reduction 16 kb single port sram embedded dynamic ram interface: 16 bit ddr, 32 / 16 bit sdram spi interface connecting serial rom and flash devices 2 usb 2.0 host independent ports with integrated phys usb 2.0 device with integrated phy ethernet mac 10/100 with mii management interface 3 independent uarts up to 115 kbps (software flow control mode) i 2 c master mode - fast and slow speed 6 general purpose i/os adc 8 bits, 230 ksps, 16 analog input channels real time clock watchdog 4 general purpose timers operating temperature: - 40 to 85 c package: pbga 384+36 6r (23x23x2.16 mm) overview spear head is a powerful digital engine belonging to spear family, the innovative customizable system on chips. the device integrates an arm core with a large set of proven ips (intellectual properties) and a configurable logic block that allows very fast customization of unique and/or proprietary solutions, with low effort and low investment. optimized for embedded applications. order codes pbga420 part number op. temp. range, c package packing SPEAR-09-H022 -40 to 85 pbga420 (23x23x2.16 mm) tray www.st.com
SPEAR-09-H022 2/55 contents 1 reference documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.1 cpu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.2 internal bus structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.3 clock system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.4 interrupt controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.5 memory system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.6 high speed connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.7 low speed connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.8 general pourpose i/os . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.9 analog to digital converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.10 real time clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.11 watchdog timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.12 general purpose timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.13 customizable logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4 pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4.1 functional pin groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4.2 special ios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 4.2.1 usb 2.0 transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 4.2.2 dram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 5 power on sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 5.1 spear head sw architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 5.1.1 boot process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 5.1.2 booting sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 6 ip description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 6.1 arm926ej-s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 6.2 clock and reset system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
SPEAR-09-H022 3/55 6.2.1 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 6.2.2 reset and pll change parameters sequence . . . . . . . . . . . . . . 30 6.3 vectored interrupt controller . . . . . . . . . . . . . . . . . . . . . . . . . . 31 6.3.1 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 6.3.2 interruptr sources in spear head . . . . . . . . . . . . . . . . . . . . . . . . . . 32 6.4 multi-port memory controller . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 6.4.1 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 6.4.2 multi-port memory controller delay lines . . . . . . . . . . . . . . . . 34 6.4.3 sstll pin configration register . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 6.5 spi memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 6.6 dma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 6.6.1 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 6.6.2 dma control state machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 6.7 usb 2.0 host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 6.7.1 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 6.8 usb 2.0 device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 6.8.1 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 6.9 ethernet mac 110 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 6.10 uart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 6.11 i 2 c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 6.11.1 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 6.11.2 i 2 c operating mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 6.11.3 i 2 c functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.12 general pourpose i/os . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 6.13 adc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 6.13.1 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 6.13.2 adc operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 6.14 watchdog timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 6.15 real time clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 6.16 general pourpose timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 6.17 customizable logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 6.17.1 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 6.17.2 custom project development . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 6.17.3 customization process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 6.17.4 power on sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
SPEAR-09-H022 4/55 6.17.5 bitstream download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 6.17.6 connection startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 6.17.7 programming interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 7 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 7.1 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 7.2 dc elettrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 7.2.1 supply voltage specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 7.2.2 i/o voltage specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 9 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
SPEAR-09-H022 1 reference documentation 5/55 1 reference documentation [1] arm926ej-s - technical reference manual [2] amba 2.0 specification [3] eia/jesd8-9 specification [4] usb2.0 specification [5] ochi specification [6] echi specification [7] utmi specification [8] usb specification [9] ieee 802.3 specification [10] i 2 c - bus specification
2 product overview SPEAR-09-H022 6/55 2 product overview spear head is a powerful system on chip based on 110nm hcmos and consists of 2 main parts: an arm based architecture and an embedded customizable logic block. the high performance arm architecture frees the user from the task of developing a complete risc system. the customizable logic block allows user to design custom logic and special functions. spear head is optimized for embedded applications and thanks to its high performance can be used for a wide range of different purposes. main blocks description: 1. cpu: arm926ej-s running at 266 mhz. it has: ? mmu ? 32 kb of instruction cache ? 16 kb of data cache ? 8 kb of instruction tcm (tightly coupled memory) ? 8 kb of data tcm ? amba bus interface ? coprocessor interface ?jtag ? etm9 (embedded trace macro-cell) for debug; large size version. 2. main bus system: a complete amba bus 2.0 subsystem connects different masters and slaves. the subsystem includes: ? ahb bus, for high performance devices ? apb bus, for low power / lower speed devices connectivity ? bus matrix, for improving connection between the peripherals parts of these buses are available for the customizable logic block. 3. clock and reset system: fully programmable block with: ? separated set up between clocks of ahb bus and apb bus peripherals ? e.m.i. reduction mode, replacing all traditional drop methods for electro-magnetic interference ? debug mode, compliant with arm debug status 4. interrupt controller: the interrupt controller has 32 interrupt sources which are prioritized and vectorized. 5. on-chip memory: 4 independent static ram cuts, 4 kb each, are available. they can be used on ahb bus or directly by the custom logic. 6. dynamic memory controller: it is a multi-port memory controller which is able to connect directly to memory sizes from 16 to 512 mbits; the data size can be 8 or 16 bits for both ddr and sdram, also 32 bits for sdram. the external data bus can be maximum 32 bit wide at maximum clock frequency of 133 mhz and have up to 4 chip selects; the accessible memory is 256 mb. internally it handles 7 ports supporting the following masters: ahb bus, bus matrix, 2 usb 2.0 hosts, usb 2.0 device, ethernet mac, easic macrocell.
SPEAR-09-H022 2 product overview 7/55 the multi-port memory controller block has a programmable arbitration scheme and the transactions happen on a different layer from the main bus. 7. serial peripheral interface: it allows a serial connection to rom and flash. the block is connected as a slave on the main ahb bus, through the bus matrix. the default bus size is 32 bit wide and the accessible memory is 64 mb at a maximum speed of 50 mhz 8. usb 2.0 hosts: these peripherals are compatible with usb 2.0 high-speed specification. they can work simultaneously either in full-speed or in high-speed mode. the peripherals have dedicated channels to the multi-port memory controller and 4 slave ports for cpu programming. the phys are embedded. 9. usb 2.0 device: the peripheral is compatible with usb 2.0 high-speed specifications. a dedicated channel connects the peripheral with the multi-port memory controller and registers and internal fifo are accessible from the cpu through the main ahb bus. an usb-plug detector block is also available to verify the presence of the vbus voltage. the port is provided with the following endpoints on the top of the endpoint 0: ? 3 bulkin / bulkout endpoints ? 2 isochronous endpoints. the phy is integrated. 10. ethernet media access control (mac) 10/100: this peripheral is compatible with ieee 802.3 standard and supports the mii management interface for the direct configuration of the external phy. it is connected to the multi-port memory controller through a dedicated channel. the ethernet controller and the configuration registers are accessible from the main ahb bus. 11. adc: 8 bit resolution, 230 ksps (kilo-sample per second), with 16 analog input channels. connected to apb bus. 12. uarts: 3 independent interfaces, up to 115 kbps each, support software flow control. connected to apb bus. 13. i 2 c supporting master mode protocol in low and full speed. connected to apb bus. 14. 6 general purpose i/o signals are available for user configuration. connected to apb bus. 15. embedded features: programmable clock system and dithered function, real time clock, watchdog, 4 general purpose timers. all blocks are interfaced with apb bus. 16. customizable logic: it consists of an embedded macro where it is possible to map up to 200k equivalent asic gates. the same logic can be alternatively used to implement 32 kbytes of sram. logic gates and ram bits can be mixed in the same configuration so that processing elements, tightly coupled with embedded memories, can be easily implemented. the macrocell has 2 dedicated buses, each of them connected with a 4 channel dma in order to speed up the data flow with the main memories. 8 interrupt lines and 112 dedicated general purpose i/os are available. to allow a simple development of project, customizable logic can be emulated by an external fpga, where customer can map his logic; fpga is easy linkable and keeps the access to all on-chip and i/os interfaces of the macro.
2 product overview SPEAR-09-H022 8/55 figure 1. block diagram 200k easic? gates 4 kb sram 4 kb sram 4 kb sram 4 kb sram 3 uarts adc 8 bits, 16 channels i2c 6 gp i/os dithered system clock wdt 4 gpts real time clock programmable interface gdma0 gdma1 bus matrix multi-port memory ctrl spi for rom, flash arm926ej-s usb 2.0 host + phy usb 2.0 host + phy usb 2.0 device + phy ethernet mac l o w s p e e d c o n n e c t i v i t y h i g h s p e e d c o n n e c t i v i t y m e m o r y i n t e r f a c e s c u s t o m e r i / o s bus bridge vic a h b b u s a p b b u s 200k easic? gates 4 kb sram 4 kb sram 4 kb sram 4 kb sram 4 kb sram 4 kb sram 4 kb sram 4 kb sram 3 uarts adc 8 bits, 16 channels i2c 6 gp i/os dithered system clock wdt 4 gpts real time clock programmable interface gdma0 gdma1 bus matrix multi-port memory ctrl spi for rom, flash arm926ej-s usb 2.0 host + phy usb 2.0 host + phy usb 2.0 device + phy ethernet mac l o w s p e e d c o n n e c t i v i t y h i g h s p e e d c o n n e c t i v i t y m e m o r y i n t e r f a c e s c u s t o m e r i / o s bus bridge vic a h b b u s a p b b u s
SPEAR-09-H022 3 features 9/55 3 features 3.1 cpu arm926ej-s risc processor f max 266 mhz (downward scalable) virtual address support with mmu 32 kb instruction cache (4 way set associative) 16 kb data cache (4 way set associative) 8 kb instruction tcm 8 kb data tcm coprocessor interface jtag etm9 (rev 2.2), large size fifo 3.2 internal bus structures multilayer structure amba 2.0 compliant f max 133 mhz high speed i/os with embedded dma function 3.3 clock system programmable clock generator pll with e.m.i. reduction low jitter pll for usb 2.0 3.4 interrupt controller irq and fiq interrupt generations support up to 32 standard interrupts support up to 16 vectored interrupts software interrupt generation 3.5 memory system memory on chip 16 kbytes single-port sram connected to easic macrocell. it can be used on ahb bus or directly by the custom logic.
3 features SPEAR-09-H022 10/55 spi 4 chip selects for asynchronous devices (rom, flash) supports normal mode 20 mhz and fast mode 50 mhz ahb slave accessible memory: 64 mb 8 / 16 / 32 bit widths programmable wait states multi-port memory controller maximum clock frequency 133 mhz support up to 7 ahb master requests ahb slave support for 8, 16 and 32 bit wide sdram support for 8 and 16 bit wide ddram 4 chip selects physical addressable memory up to 256 mb memory clock tuning to match the timing of different memory vendors 3.6 high speed connectivity usb 2.0 host 2 usb 2.0 host controllers with their utmi phy port embedded high-speed / full-speed / low-speed modes usb 2.0 complaint dma fifo 4 ahb slaves for configuration and fifo access 4 ahb masters for data transfer usb 2.0 device udc 2.0 controller with embedded phy high-speed / full-speed / low-speed modes usb 2.0 complaint usb self-power mode dma fifo ahb master interface for dma transfer ahb slaves for: configuration, fifo access, plug autodetect endpoints on the top of endpoint 0: 3 bulkin / bulkout, 2 isochronous ethernet 10/100 mac110 controller compliant with ieee 802.3 standard supporting mii 10/100 mbits/s mii management protocol interface tx fifo (512x36 dual port)
SPEAR-09-H022 3 features 11/55 rx fifo (512x36 dual port) ahb dma master connected to memory system ahb slave for configuration 3.7 low speed connectivity uart support for 8 bit serial data tx and rx selectable 2 / 1 stop bits selectable even, odd and no parity parity, overrun and framing error detector max transfer rate: 115 kbps i 2 c standard i 2 c mode (100 khz) / fast i 2 c mode (400 khz) master interface only master functions control all i 2 c bus specific sequencing, protocol, arbitration and timing detection of bus errors during transfers 3.8 general pourpose i/os 6 programmable gp i/os 3.9 analog to digital converter 8 bit resolutions 230 ksps 16 analog input channels (0 - 3.3 v) inl 1 lsb dnl 0.5 lsb programmable conversion speed - minimum conversion time 4.3 s 3.10 real time clock real time clock-calendar (rtc) 14 digit (yyyy mm dd hh mm ss) precision clocked by 32.768 khz low power clock input separated power supply (1.2 v)
3 features SPEAR-09-H022 12/55 3.11 watchdog timer programmable 16 bit watchdog timer with reset output signal (more than 200 system clock period to initial peripheral devices) programmable period 1 ~ 10 sec for recovery from unexpected system hang-up 3.12 general purpose timers four 16 bit timers with 8 bit prescaler frequency range: 3.96 hz - 66.5 mhz operating mode: auto reload and single shot 3.13 customizable logic 200k equivalent asic gate configurable either custom logic or 32 kbytes single-port sram or mixing logic and ram 2 dedicated buses, each of them connected with a 4 channel dma 8 interrupt lines (level type) available 112 dedicated gp i/os single via mask configurable interconnections emulation by an external fpga, keeping on-chip and i/o interfaces
SPEAR-09-H022 4 pin description 13/55 4 pin description 4.1 functional pin groups with reference to figure 14 . package schematic - section 8 , here follows the pin list, sorted by their belonging ip. all supply and ground pins are classified as power signals and gathered in the table 2 . table 1. pin description by functional groups group signal name ball direction function pin type adc ain[0] v20 input adc analog input channel analog buffer, 3.3 v capable ain[1] v19 ain[2] v18 ain[3] v17 ain[4] v16 ain[5] v15 ain[6] v14 ain[7] v12 ain[8] v11 ain[9] v10 ain[10] v9 ain[11] v8 ain[12] u22 ain[13] u21 ain[14] u20 ain[15] u19 test_out v13 output adc output test pad debug test0 e22 input test configuration port. for the functional mode they have to be set to 0 ttl input buffer, 3.3 v capable, with pull down test1 e21 test2 d22 test3 d21 pll_bypass y5 input enable / disable pll bypass ttl schmitt trigger input buffer, 3.3 v capable easic easicgp_io[0] g4 i/o easic general purpose io ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability easicgp_io[1] g3
4 pin description SPEAR-09-H022 14/55 easic easicgp_io[2] g2 i/o easic general purpose io ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability easicgp_io[3] f5 easicgp_io[4] f4 easicgp_io[5] f3 easicgp_io[6] f2 easicgp_io[7] e9 easicgp_io[8] e8 easicgp_io[9] e7 easicgp_io[10] e6 easicgp_io[11] e5 easicgp_io[12] e4 easicgp_io[13] e3 easicgp_io[14] e2 easicgp_io[15] d8 easicgp_io[16] d7 easicgp_io[17] d6 easicgp_io[18] d5 easicgp_io[19] d4 easicgp_io[20] d3 easicgp_io[21] d2 easicgp_io[22] c8 easicgp_io[23] c7 easicgp_io[24] c6 easicgp_io[25] c5 easicgp_io[26] c4 easicgp_io[27] c3 easicgp_io[28] c2 easicgp_io[29] b8 easicgp_io[30] b7 easicgp_io[31] b6 easicgp_io[32] b5 easicgp_io[33] b4 easicgp_io[34] b3 table 1. pin description by functional groups (continued) group signal name ball direction function pin type
SPEAR-09-H022 4 pin description 15/55 easic easicgp_io[35] b2 i/o easic general purpose io ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability easicgp_io[36] a8 easicgp_io[37] a7 easicgp_io[38] a6 easicgp_io[39] a5 easicgp_io[40] a4 easicgp_io[41] a3 easicgp_io[42] a2 easicgp_io[43] d9 easicgp_io[44] c9 easicgp_io[45] b9 easicgp_io[46] a9 easicgp_io[47] e10 easicgp_io[48] d10 easicgp_io[49] c10 easicgp_io[50] b10 easicgp_io[51] a10 easicgp_io[52] e11 easicgp_io[53] d11 easicgp_io[54] c11 easicgp_io[55] b11 easicgp_io[56] a11 easicgp_io[57] e12 easicgp_io[58] d12 easicgp_io[59] c12 easicgp_io[60] b12 easicgp_io[61] a12 easicgp_io[62] e13 easicgp_io[63] d13 easicgp_io[64] c13 easicgp_io[65] b13 table 1. pin description by functional groups (continued) group signal name ball direction function pin type
4 pin description SPEAR-09-H022 16/55 easic easicgp_io[66] a13 i/o easic general purpose io ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability easicgp_io[67] e14 easicgp_io[68] d14 easicgp_io[69] c14 easicgp_io[70] b14 easicgp_io[71] a14 easicgp_io[72] e15 easicgp_io[73] d15 easicgp_io[74] c15 easicgp_io[75] b15 easicgp_io[76] a15 easicgp_io[77] e16 easicgp_io[78] d16 easicgp_io[79] c16 easicgp_io[80] b16 easicgp_io[81] a16 easicgp_io[82] e17 easicgp_io[83] d17 easicgp_io[84] c17 easicgp_io[85] b17 easicgp_io[86] a17 easicgp_io[87] l18 easicgp_io[88] k18 easicgp_io[89] j18 easicgp_io[90] h18 easicgp_io[91] g18 easicgp_io[92] f18 easicgp_io[93] e18 easicgp_io[94] d18 easicgp_io[95] c18 easicgp_io[96] b18 easicgp_io[97] a18 easicgp_io[98] j19 table 1. pin description by functional groups (continued) group signal name ball direction function pin type
SPEAR-09-H022 4 pin description 17/55 easic easicgp_io[99] h19 i/o easic general purpose io ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability easicgp_io[100] g19 easicgp_io[101] f19 easicgp_io[102] e19 easicgp_io[103] d19 easicgp_io[104] c19 easicgp_io[105] b19 easicgp_io[106] a19 easicgp_io[107] g20 easicgp_io[108] f20 easicgp_io[109] e20 easicgp_io[110] d20 easicgp_io[111] c20 easic_ext_clock b21 easic_pi_clock r18 eaisc program interface out clock ttl bidirectional buffer, 3.3 v capable, 8 ma drive capability easic_clk g5 easic output clock config_devel a20 input external fpga emulation mode ttl input buffer, 3.3 v capable with pull down ethernet tx_clk j20 input ethernet input tx clock ttl bidirectional buffer, 5 v tolerant, 4 ma drive capability, with pull down txd[0] j21 output ethernet tx output data txd[1] j22 txd[2] k19 txd[3] k20 tx_en k21 ethernet tx enable crs k22 input carrier sense input col l19 collision detection input rx_clk l20 ethernet input rx clock rxd[0] l21 ethernet rx input data rxd[1] l22 rxd[2] m19 rxd[3] m20 input rx_dv m21 input data valid on rx rx_er m22 input data error detected table 1. pin description by functional groups (continued) group signal name ball direction function pin type
4 pin description SPEAR-09-H022 18/55 ethernet mdc n19 output output timing reference for mdio ttl bidirectional buffer, 5 v tolerant, 4 ma drive capability, with pull down mdio n20 i/o i/o data to phy gpi/os gp_io[0] t22 i/o general purpose io ttl bidirectional buffer, 3.3 v capable, 8 ma drive capability gp_io[1] t21 gp_io[2] t20 gp_io[3] t19 gp_io[4] r22 gp_io[5] r21 i2c sda n21 i 2 c serial data ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability, with pull up scl n22 jtag tdo a21 output jtag tdo ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability tdi a22 input jtag tdi ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability, with pull up tms b20 input jtag tms rtck b22 output jtag output clock tck c21 input jtag clock ntrst c22 output jtag reset master clock mclk_in t1 input 12 mhz input cristal oscillator 3.3 v capable mclk_out u1 output 12 mhz output cristal master reset mreset h4 input master reset ttl schmitt trigger input buffer, 3.3 v capable mpmc mpmcdata[0] aa12 i/o ddr / sdram data lvttl / sstl classii bidirectional buffer mpmcdata[1] y12 mpmcdata[2] w12 mpmcdata[3] ab13 mpmcdata[4] aa13 mpmcdata[5] y13 mpmcdata[6] w13 table 1. pin description by functional groups (continued) group signal name ball direction function pin type
SPEAR-09-H022 4 pin description 19/55 mpmc mpmcdata[6] w13 i/o ddr / sdram data lvttl / sstl classii bidirectional buffer mpmcdata[7] aa14 mpmcdata[8] aa16 mpmcdata[9] ab18 mpmcdata[10] ab19 mpmcdata[11] ab20 mpmcdata[12] ab21 mpmcdata[13] aa21 mpmcdata[14] ab22 mpmcdata[15] aa22 mpmcdata[16] aa18 i/o sdram data ttl bidirectional buffer, 3.3 v capable, 8 ma drive capability mpmcdata[17] aa17 mpmcdata[18] y22 mpmcdata[19] y21 mpmcdata[20] y20 mpmcdata[21] y19 mpmcdata[22] y18 mpmcdata[23] y17 mpmcdata[24] y16 mpmcdata[25] w22 mpmcdata[26] w21 mpmcdata[27] w20 mpmcdata[28] w19 mpmcdata[29] w18 mpmcdata[30] w17 mpmcdata[31] w16 mpmcaddrout[0] ab8 output ddr / sdram data lvttl / sstl classii bidirectional buffer mpmcaddrout[1] aa8 mpmcaddrout[2] y8 mpmcaddrout[3] w8 mpmcaddrout[4] ab9 mpmcaddrout[5] aa9 mpmcaddrout[6] y9 mpmcaddrout[7] w9 mpmcaddrout[8] ab10 table 1. pin description by functional groups (continued) group signal name ball direction function pin type
4 pin description SPEAR-09-H022 20/55 mpmc mpmcaddrout[9] aa10 output ddr / sdram data lvttl / sstl classii bidirectional buffer mpmcaddrout[10] y10 mpmcaddrout[11] w10 mpmcaddrout[12] ab11 mpmcaddrout[13] aa11 mpmcaddrout[14] y11 nmpmcdycsout[0] ab6 ddr / sdram chip select nmpmcdycsout[1] aa6 nmpmcdycsout[2] y6 nmpmcdycsout[3] w6 mpmcckeout[0] w11 ddr / sdram clock enable output mpmcckeout[1] ab12 mpmcclkout[0] ab17 ddr / sdram output clock 1 lvttl / sstl classii bidirectional differential buffer nmpmcclkout[0] ab16 ddr / sdram output clock 1 neg. mpmcclkout[1] ab15 ddr / sdram output clock 2 nmpmcclkout[1] ab14 ddr / sdram output clock 2 neg. mpmcdqmout[0] y14 ddr / sdram data mask out lvttl / sstl classii bidirectional buffer mpmcdqmout[1] w15 mpmcdqmout[2] aa19 sdram data mask out ttl bidirectional buffer, 3.3 v capable, 8 ma drive capability mpmcdqmout[3] aa20 mpmcdqs[0] aa15 ddr data strobe lvttl / sstl classii bidirectional buffer mpmcdqs[1] y15 nmpmccasout y7 ddr / sdram cas output strobe nmpmcrasout aa7 nmpmcweout ab7 ddr / sdram write enable sstl_vref w14 input voltage reference sstl / cmos mode. this pin is used both as logic state and as power supply analog buffer, 3.3 v capable rtc rtcxo ab5 output 32 khz output crystal oscillator 1.2 v capable rtcxi ab4 input 32 khz input crystal smi smincs[0] g22 output serial flash chip select ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability table 1. pin description by functional groups (continued) group signal name ball direction function pin type
SPEAR-09-H022 4 pin description 21/55 smi smincs[1] g21 serial flash chip select ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability smincs[2] f22 smincs[3] f21 smiclk h20 output serial flash output clock ttl bidirectional buffer, 3.3 v capable, 8 ma drive capability smidatain h21 input serial flash data in ttl bidirectional buffer, 3.3 v capable, 8 ma drive capability, with pull up smidataout h22 output serial flash data out ttl bidirectional buffer, 3.3 v capable, 8 ma drive capability uarts uart1_rxd p19 input uart1 rx data ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability, with pull down uart1_txd p20 output uart1 tx data ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability uart2_rxd p21 input uart2 rx data ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability, with pull down uart2_txd p22 output uart2 tx data ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability uart3_rxd r19 input uart3 rx data ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability, with pull down uart3_txd r20 output uart3 tx data ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability table 1. pin description by functional groups (continued) group signal name ball direction function pin type
4 pin description SPEAR-09-H022 22/55 usbs dmns w1 i/o d - port of usb device analog buffer, 5 v tolerant dpls v1 i/o d + port of usb device host1_dp p1 i/o d - port of usb host1 host1_dm n1 i/o d + port of usb host1 host2_dp l1 i/o d - port of usb host2 host2_dm k1 i/o d + port of usb host2 host1_vbus h2 output usb host1 vbus signal ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability host2_vbus h1 output usb host2 vbus signal overcurh1 g1 i/o usb host1 overcurrent ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability, with pull down overcurh2 f1 i/o usb host2 overcurrent ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability vbus h3 i/o usb device vbus signal ttl bidirectional buffer, 3.3 v capable, 4 ma drive capability, with pull down rref k5 input usb reference resistor analog buffer, 3.3 v capable table 2. pins belonging to power group group signal name ball function power vdde3v3 note 1 digital 3.3 v power vdd note 2 digital 1.2 v power gnde note 3 digitalground vdd3core v22 dedicated adc 3.3 v power vsscore u18 dedicated adc ground vrefp_adc v21 adc positive reference voltage vrefn_adc t18 adc pegative reference voltage group signal name ball function table 1. pin description by functional groups (continued) group signal name ball direction function pin type
SPEAR-09-H022 4 pin description 23/55 note: 1 signal spread on the following balls: f7, f8, f9, f12, f13, f14, f17, g17 h6, j6, k7, l7, m5, n6, p6, p7,r7, u6, u16. 2 signal spread on the following balls: f6, f10, f11, f15, f16, g6, h17, j17, k6, l6, m17, n17, r6, t6, t17, u17. 3 signal spread on the following balls: j9 to j14, k9 to k14, l9 to l14, m9 to m14, n9 to n14, p9 to p14. 4 signal spread on the following balls: u7 to u15 power vdd3core w7 ddr / sdr dedicated digital pll 3.3 v power vsscore v7 drr / sdr dedicated digital pll ground sstl_vref w14 voltage reference sstl / cmos mode. this pin is used both as logic state and as power supply vdde3v3 note 4 ddr / sdr digital 3.3 / 2.5v power vdde3v3 ab2 3.3 v dedicated power for rtc vdd aa5 1.2 v dedicated power for rtc gnd aa4 dedicated digital ground for rtc gnde ab3 dedicated digital ground for rtc vdd3core r2 dedicated usb pll analog 3.3 v power vsscore p4 dedicated usb pll analog ground vddcore r4 dedicated usb pll digital 1.2 v power vsscore u2 dedicated usb pll digital ground vddcore w3 dedicated usb 1.2 v power vddcore u4 dedicated usb 1.2 v power vddcore u3 dedicated usb 1.2 v power vdd p2 dedicated usb 1.2 v power vddcore n5 dedicated usb 1.2 v power vddcore n3 dedicated usb 1.2 v power vddcore l4 dedicated usb 1.2 v power vddcore k4 dedicated usb 1.2 v power vddcore k3 dedicated usb 1.2 v power vddcore j4 dedicated usb 1.2 v power vdd3core w4 dedicated usb 3.3 v power vdde3v3 p5 dedicated usb 3.3 v power vdd3core l3 dedicated usb 3.3 v power vdd3core j3 dedicated usb 3.3 v power vsscore w5 dedicated usb ground vsscore w2 dedicated usb ground vsscore u5 dedicated usb ground gnde r3 dedicated usb ground gnd n4 dedicated usb ground vsscore n2 dedicated usb ground vsscore m2 dedicated usb ground table 2. pins belonging to power group (continued)
4 pin description SPEAR-09-H022 24/55 4.2 special ios 4.2.1 usb 2.0 transceiver spear head has three usb 2.0 utmi + multimode atx transceivers. one transceiver will be used by the usb device controller, and two will be used by the hosts. these are all integrated into a single usb three-phys macro. 4.2.2 dram data and address buses of multi-port memory controller used to connect to the banks memory are constituted of programmable pins.
SPEAR-09-H022 5 power on sequence 25/55 5 power on sequence 5.1 spear head sw architecture 5.1.1 boot process memory mapping a major consideration in the design of an embedded arm application is the layout of the memory map, in particular the memory that is situated at address 0x0. following reset, the core starts to fetch instructions from 0x0, so there must be some executable code accessible from that address. in an embedded system, this requires rom to be present, at least initially. serial flash at 0x0 the spear head has been designed to use the remap concept into its ahb primary bus decoder. the decoder selection for the initial address range (first 64 mb) is conditioned with the content of a ahb remap register, which can be programmed by software at any time. the serial flash memory space is accessible in the address range 0x9600_0000 - 0x99ff_ffff (64 mb), with or without remap. at reset, before remapping, the serial flash memory is 'aliased' at 0x0, which means that the ahb decoder selects the serial flash space when accessing the address range 0x0000_0000 to 0x03ff_ffff. table 3. memory mapping at reset - before remapping dram at 0x0 after reset, the boot program makes the remapping, so that the system will be able to access the complete 256 mb of logic memory space associated to dram in the range 0x0000_0000 - 0x0fff_ffff. table 4. memory mapping after reset after remapping address range size [mb] description 0x9600_0000 - 0x99ff_ffff 64 serial flash unreachable in this state n. a. dram 0x0000_0000 - 0x03ff_ffff 64 serial flash (remap) address range size [mb] description 0x9600_0000 - 0x99ff_ffff 64 serial flash 0x0000_0000 - 0x0fff_ffff 256 dram
5 power on sequence SPEAR-09-H022 26/55 5.1.2 booting sequence a simple initial description of the boot process is showed in the following steps: 1. power on to fetch the reset vector at 0x0000_0000 (from the aliased-copy of serial flash). 2. perform any critical cpu initialization at this time. 3. load into the program counter (pc) the address of a routine that will be executed directly from the non-aliased mapping of serial flash (0x9600_0000 + addr_of_routine) and which main objectives are: ? un-map the aliased-copy of the serial flash (set remap = 1) ? copy the program text and data into dram. 4. returning from this routine will set the program counter back to dram.
SPEAR-09-H022 6 ip description 27/55 6 ip description in this section you can find the description of the ip's embedded in spear head. 6.1 arm926ej-s the processor is the powerful arm926ej-s, targeted for multi-tasking applications. belonging to arm9 general purposes family microprocessor, it principally stands out for the memory management unit, which provides virtually memory features, making it also compliant with windowsce, linux and symbianos operating systems. the arm926ej-s supports the 32 bits arm and 16 bit thumb instruction sets, enabling the user to trade off between high performance and high code density and includes features for efficient execution of java byte codes. besides, it has the arm debug architecture and includes logic to assist in both hardware and software debug. its main features are: f max 266 mhz (downward scalable) mmu 32 kb of instruction cache 16 kb of data cache 8 kb of instruction tcm (tightly coupled memory) 8 kb of data tcm amba bus interface coprocessor interface jtag etm9 (embedded trace macro-cell) for debug; large size version.
6 ip description SPEAR-09-H022 28/55 figure 2. arm926ej-s block diagram
SPEAR-09-H022 6 ip description 29/55 6.2 clock and reset system 6.2.1 overview the clock system is a fully programmable block able to generate every clock necessary at the chip (except for usb 2.0 host and device controllers, which have a dedicated pll); they are: clock @ 266 mhz for arm system clock @133mhz for all ips on ahb bus clock @ 66.5 mhz for apb bridge and apb peripherals clock for easic macrocell clock for easic programmable interface the block has an embedded pll, featuring electro-magnetic interference reduction. user has the possibility to set up the pll in order to add a triangular wave to the vco clock; the resulting signal will have the spectrum (and the power) spread on a small range (programmable) of frequencies centred on f 0 ( vco freq.), obtaining minimum electromagnetic emissions. this method replace all the other traditional methods of e.m.i. reduction, as filtering, ferrite beads, chokes, adding power layers and ground planets to pcbs, metal shielding etc., allowing sensible cost saving for customers. figure 3. clock system block interfaces the i/o signals accessible from off-chip are listed in tabl e 5 . clock system i/o off-chip interface: table 5. clock system i/o off-chip interface signals direction size [bit] description mclk_in input 1 oscillator input (12 mhz) pll_bypass input 1 external clock in test mode mclk_out output 1 oscillator output. it supplies the signal mclk_in inverted mreset input 1 asynchronous reset mclk_out mclk_in clock system mreset pll_bypass internal clocks mclk_out mclk_in clock system mreset pll_bypass internal clocks
6 ip description SPEAR-09-H022 30/55 the reference clock frequency is 12 mhz and it is used to generate the 266 mhz clock by an internal pll. then starting by this, output signals are generated programming the clock system registers, via apb bus. the purpose of pll_bypass mainly is let the rest of the chip working properly even in case of pll failure. 6.2.2 reset and pll change parameters sequence figure 4 shows a simplified flow chart of clock system fsm. the system remains in an idle state until reset signal is asserted: reset 0. when reset = 0 the fsm change state and reaches the pll_pwr-up state; when pll locks (pll_lock = 1), means that the pll_out signal oscillates at 264 mhz and the pll starts to work, so that the fsm advances in the next states. in clock_enabled state the clocks can propagate in the system; then the fsm goes in system_on state; it remains in this state in the normal chip working. figure 4. state machine of clock system to reach at a clock frequency of 266 mhz, pll had to be appropriately programmed because this frequency isn't an integer multiple of 12 mhz. after this programming, the fsm stops all the clocks and exits from system on state proceeding in pll setting state; here the new parameters are stored in the pll. if the pll isn't in dithered mode the fsm waits for pll lock, going in lock wait state, and then will reach system on state when pll locks.
SPEAR-09-H022 6 ip description 31/55 if the pll is in dithered mode, the lock signal loses his meaning and there's no need to wait for pll lock, so the fsm jumps directly from pll setting to system on. when fsm is in system on, all clocks are enabled. 6.3 vectored interrupt controller 6.3.1 overview the vector interrupt controller provides a software interface to interrupt system, in order to determine the source that is requesting a service and where the service routing is loaded. it supplies the starting address, or vector address, of the service routine corresponding to the highest priority requesting interrupt source. in an arm system 2 level of interrupt are available: fast interrupt request (fiq) for low latency interrupt handling interrupt request (irq) for standard interrupts generally, you only use a single fiq source at a time to provide a true low-latency interrupt. this has the following benefits: you can execute the interrupt service routine directly without determining the source of the interrupt it reduces interrupt latency. you can use the banked registers available for fiq interrupts more efficiently, because you do not require a context save the interrupt inputs must be level sensitive, active high, and held asserted until the interrupt service routine clears the interrupt. edge-triggered interrupts are not compatible. the interrupt inputs do not have to be synchronous to ahb clok. the main features of vectored interrupt controller are: compliance to amba specification rev. 2.0 irq and fiq interrupt generation ahb mapped for faster interrupt hardware priority support for 32 standard interrupts support for 16 vectored interrupts software interrupt generation interrupt masking interrupt request status. since 32 interrupts are supported, there are 32 interrupt input lines, coming from different sources. they are selected by a bit position and the software controls every line to generate software interrupts; it can generate 16 vectored interrupts. a vectored interrupt can generate only an irq interrupt. the interrupt priority is controlled by hardware and it is as follow: 1. fiq interrupt 2. vectored irq interrupt. the higher priority is 0; the lower is 15 3. non vectored irq interrupt
6 ip description SPEAR-09-H022 32/55 6.3.2 interruptr sources in spear head table 6. interrupt sources in spear head interrupt line source 0easic0 1easic1 2easic2 3easic3 4spi 5rtc 6 usb host 1 ? ohci 7 usb host 2 ? ohci 8 usb host 1 ? ehci 9 usb host 2 ? ehci 10 usb device 11 mac 12 i2c 13 gpt4 14 gpt3 15 gdma1 16 gdma0 17 gpt2 18 gpt1 19 uart2 20 uart1 21 uart0 22 adc 23 reserved 24 reserved 25 reserved 26 reserved 27 reserved 28 easic4 29 easic5 30 easic6 31 easic7
SPEAR-09-H022 6 ip description 33/55 6.4 multi-port memory controller 6.4.1 overview the dram interface is controlled by the on-chip multi-port memory controller. its main features are: supports for sdram up to 32 bit wide supports for ddr up to 16 bit wide maximum clock frequency 133 mhz 8 ahb port connections 4 chip selects total addressable memory: 256 mb maximum memory bank size: 64 mb read and write buffers to reduce latency programmable timings table 7. supported memory cuts size [mb] bank number row length column length 16 (2 mb x 8 bits) 2 11 9 16 (1 mb x 16 bits) 2 11 8 64 (8 mb x 8 bits) 4 12 9 64 (4 mb x 16 bits) 4 12 8 64 (2 mb x 32 bits) 4 11 8 128 (16 mb x 8 bits) 4 12 10 128 (8 mb x 16 bits) 4 12 9 128 (4 mb x 32 bits) 4 12 8 256 (32 mb x 8 bits) 4 13 10 256 (16 mb x 16 bits) 4 13 9 256 (8 mb x 32 bits) 4 13 8 512 (64 mb x 8 bits) 4 13 11 512 (32 mb x 16 bits) 4 13 10 table 8. multi-port memory controller ahb port assignment port size [bit] priority master 032 maxbus matrix 1- reserved 232 easic 3 32 usb 2.0 device 4 32 usb 2.0 host 1
6 ip description SPEAR-09-H022 34/55 the table is compiled in decreasing order of priority. the i/o interfaces accessible from off-chip are listed here: 6.4.2 multi-port memory controller delay lines as shown in figure 5 , there are 4 dlls. the clockout delay line is used to tuner the clock driven from multi-port memory controller to external dram to match setup / hold constraints on external memory. this delay lines is used in the "clock delay methodology". the hclk delay lines delays the dram command signal (addr, cas, ras, ...) to capture easily read data from dram; this technique is called "command delay". the dqsinl and dqsinh delay lines delay respectively the dqs0 (least 8 bit data strobe) and dqs1 (highest 8 bit of data strobe) signals coming from ddr. delay lines are setting by programming their register through apb bus. port size [bit] priority master 5 32 usb 2.0 host 2 6 32 ethernet mac 7 32 min main ahb system bus table 9. multi-port memory controller off-chip interfaces signal direction size [bit] description mpmcdqs input 2 data strobe mpmcdata bidirectional 32 read / write data mpmcclkout output 2 dram clock nmpmcclkout output 2 dram inverted clock mpmcckeout output 2 dram clock enable mpmcdqmout output 4 data mask nmpmcrasout output 1 ras (active low) nmpmccasout output 1 cas (active low) nmpmcweout output 1 write enable (active low) nmpmcdycsout output 4 chip select (active low) mpmcaddrout output 15 address sstl_vref input 1 voltage reference sstl / cmos mode: sstl 1.25 v cmos 0 v this pin is used both as logic state and as power supply. table 8. multi-port memory controller ahb port assignment (continued)
SPEAR-09-H022 6 ip description 35/55 figure 5. multi-port memory controller dll 6.4.3 sstll pin configration register the stub series-terminated logic (sstl) interface standard is intended for high-speed memory interface applications and specifies switching characteristics such that operating frequencies up to 200 mhz are attainable. the primary application for sstl devices is to interface with ddrs. in spear head the sstl pins are: mpmcdata[15:0] mpmcaddrout mpmcclkout nmpmcclkout. these pins are set through configuration registers on apb bus. 6.5 spi memories spear head supports the spi memory devices flash and eeprom. spi controller provides an ahb slave interface to spi memories and allows cpu to use them as data storage or code execution. main features are spi master type up to 20 mhz clock speed in standard read mode and 50 mhz in fast read mode 4 chip selects up to 16 mbytes address space per bank selectable 3-bytes addressing for flash and 2-bytes addressing for eeprom programmable clock prescaler external memory boot mode capability mpmc ddr clockout dll addr, cas, ras, we, .. data_out data_in dqs dram command driver hclk dll hclk hclk_dly dqsinl dqsinu dll sdr ddr mpmc ddr clockout dll addr, cas, ras, we, .. data_out data_in dqs dram command driver hclk dll hclk hclk_dly dqsinl dqsinu dll sdr ddr
6 ip description SPEAR-09-H022 36/55 32, 16 or 8 bit ahb interface interrupt request on write complete or software transfer complete the compatible spi memories are: ? stmicroelectronics m25pxxx, m45pxxx ? stmicroelectronics m95xxx except m95040, m95020 and m95010 ? atmel at25fxx ?ymc y25fxx ? sst sst25lfxx the i/o interfaces accessible from off-chip are listed here: table 10. smc signal interfaces description at power on the boot code is enabled from the static memory bank0 by default; this has to be a flash bank memory. moreover, at power on, the memory clock signal is 19 mhz, the "release from deep power down" is 29 s and the base address for external memories is 0x0. 6.6 dma 6.6.1 overview spear head has 2 dma controllers used to transfer data between aasic? macrocell and memory. a dma controller can service up to 4 data streams at one time; a data transfer consists of a sequence of a dma data packet transfers. there are two types of a data packet transfer one is from the source to the dma controller one other is from dma controller to the destination. each dma controller has an ahb master interface to transfer data between dma controller and either a source or a destination, and has an apb slave interface used to program its registers. signal direction size [bit] description smidatain input 1 memory input smidataout output 1 memory output smiclk output 1 clock smincs output 4 bankchip selects (active low)
SPEAR-09-H022 6 ip description 37/55 6.6.2 dma control state machine figure 6. dma state machine diagram the dma control sm is always reset into the idle state. as a channel request is asserted, sm moves to read state and the ahb master will start a data packet transfer; sm selects appropriate source address. when sm is in write state, it selects the destination address and the data width from the data stream register and the ahb master will transfer all data from the fifo to the destination. when the ahb master has transferred the data packet, it asserts a packend signal and the sm will move to the next state, which depends on the channel request signals. the state transitions from the read or write states can occur only when a whole data packet has been transferred. figure 7. data packet transfer
6 ip description SPEAR-09-H022 38/55 6.7 usb 2.0 host 6.7.1 overview two blocks drive the usb 2.0 host interfaces on spear head. the first is the usb2.0phy that executes the serialization and the de-serialization and implements the transceiver for the usb line. the second part is the uhc (usb2.0 host controller). it is connected on ahb bus and generates the commands for usb2.0phy in utmi+ interface. as there are two usb hosts, there is one phy and one uhc for each usb host port. 6.7.1.1 usb2.0phy the usb2.0phy is a hard macro designed using standard cells and custom cells. in this way has been possible to reach the max speed of usb: 480 mbits/sec. the block is able to set his speed in ls / fs for usb 1.1 and in hs for usb 2.0. 6.7.1.2 uhc the uhc is able to detect the usb speed configuration: usb 1.1 (ls / fs), usb 2.0 (hs) via utmi+ interface. when the speed is detected, the controller uses 2 sub-controllers: ehci (enhanced host controller interface) for 2.0 configuration and ohci (open host controller interface) for 1.1 configuration. there is an ahb master and a slave for everyone of these controllers.
SPEAR-09-H022 6 ip description 39/55 6.8 usb 2.0 device 6.8.1 overview three blocks drive the usb 2.0 device interface on spear head. the first one is the usb2.0phy, which executes the serialization and the de-serialization and implements the transceiver for the usb line. the second is the udc (usb 2.0 device controller). it is connected on ahb bus and generates the commands for usb2.0phy in utmi+ interface. the last block is the usb plug detect, which detects the connection of the device. 6.8.1.1 usb2.0phy the usb2.0phy is a hard macro designed using standard cells and custom cells. in this way is possible to reach the max speed hs of usb: 480 mbits/sec. 6.8.1.2 udc the udc is able to detect the usb connection speed via utmi+ interface. there is an ahb master and three slaves. the udc contains 6 endpoints (0 control, 1 bulk in, 2 bulk out, 3 iso in, 4 iso out, 5 interrupt in) and 4 configurations. 6.9 ethernet mac 110 the ethernet media access controller (mac 110) incorporates the requirements for operation of an ethernet / ieee 802.3 compliant node and provides interface between the host system and the media independent interface (which is embedded in spear head). mac 110 core features are: it can operate either in 100 mbps mode or 10 mbps mode, depending on the clock provided on the mii interface it can operate both in half-duplex mode and full-duplex mode. when operating in the half-duplex mode, the mac110 core is fully compliant to section 4 of iso / iec 8802-3 (ansi / ieee standard) and ansi / ieee 802.3. when operating in the full-duplex mode, the mac110 core is compliant to the ieee 802.3x standard for full-duplex operations. it is also compatible with home pna 1.1. the mac110 core provides programmable enhanced features designed to minimize host supervision, bus utilization, and pre- or post-message processing. these features include: ability to disable retires after a collision dynamic fcs generation on a frame-by-frame basis automatic pad field insertion and deletion to enforce minimum frame size attributes automatic retransmission and detection of collision frames. the mac110 core can sustain transmission or reception of minimal-sized back-to-back packets at full line speed with an inter-packet gap (ipg) of 90.6 s for 10 mb/s and 0.96 s for 100 mb/s.
6 ip description SPEAR-09-H022 40/55 the five primary attributes of the mac block are: 1. transmit and receive message data encapsulation ? framing (frame boundary delimitation, frame synchronization) ? error detection (physical medium transmission errors) 2. media access management ? medium allocation (collision detection, except in full-duplex operation) ? contention resolution (collision handling, except in full-duplex operation) 3. flow control during full duplex mode ? decoding of control frames (pause command) and disabling the transmitter ? generation of control frames 4. interface to the phy ? support of mii protocol to interface with a mii based phy 5. management interface support on mii ? generation of phy management frames on the mdc / mdi / mdo. to minimize the cpu load during the data transfer is available a local dma with fifo capable to fetch itself the descriptors for the data blocks and to manage the data according to the instruction included on the descriptor. figure 8. block diagram of ethernet controller 6.10 uart uart provides a standard serial data communication with transmit and receive channels that can operate concurrently to handle a full-duplex operation. two internal fifo for transmitted and received data, deep 16 and wide 8 bits, are present; these fifo can be enabled or disabled through a register. interrupts are provided to control reception and transmission of serial data. local fifo mii i/f mim mac block dma rx and tx logic conguration register array ahb master ahb slave data configuration local fifo mii i/f mim mac block dma rx and tx logic conguration register array ahb master ahb slave data configuration
SPEAR-09-H022 6 ip description 41/55 the clock for both transmit and receive channels is provided by an internal baud-rate generator that divides the ahb bus clock by any divisor value from 1 to 255. the output clock frequency of baud generator is sixteen times the baud rate value. the maximum speed achieved is 115 kbauds. in spear head there are 3 uart's, apb bus slaves. 6.11 i 2 c 6.11.1 overview the controller serves as an interface between the apb bus and the serial i 2 c bus. it provides master functions, and controls all i 2 c bus-specific sequencing, protocol, arbitration and timing. supported standard (100 khz) and fast (400 khz) i 2 c mode. figure 9. i 2 c controller block diagram main features are: parallel-bus apb / i 2 c protocol converter standard i 2 c mode (100 khz) / fast i2c mode (400 khz) master interface (only). detection of bus errors during transfers control of all i 2 c bus-specific sequencing, protocol, arbitration and timing in addition to receiving and transmitting data, this interface converts it from serial to parallel format and vice versa, using either an interrupt or a polled handshake. the interrupts can be enabled or disabled by software. the interface is connected to the i 2 c bus by a data pin (sda) and by a clock pin (scl). sda signal is synchronized by scl signal. 6.11.2 i 2 c operating mode communication flow in master mode, it initiates a data transfer and generates the clock signal. a serial data transfer always begins with a start condition and ends with a stop condition. both start and stop conditions are generated by software. apb interface register array slc control sda control apb bus i2c bus apb interface register array slc control sda control apb bus i2c bus
6 ip description SPEAR-09-H022 42/55 the first byte following the start condition is the address byte; it is always transmitted in master mode. a 9 th clock pulse follows the 8 clock cycles of a byte transfer, during which the receiver must send an acknowledge bit to the transmitter. figure 10. i 2 c timing acknowledge may be enabled and disabled by software. the i 2 c interface address and / or general call address can be selected by software. the speed of the i 2 c interface may be selected between standard (0 - 100 khz) and fast (100 - 400 khz). sda / scl line control transmitter mode: the interface holds the clock line low before transmission to wait for the microcontroller to write the byte in the data register. receiver mode: the interface holds the clock line low after reception to wait for the microcontroller to read the byte in the data register. the scl frequency (fscl) is controlled by a programmable clock divider which depends on the i 2 c bus mode. when the i 2 c cell is enabled, the sda and scl ports must be configured as floating open-drain output or floating input. in this case, the value of the external pull-up resistance used depends on the application. 6.11.3 i 2 c functional description master mode the i 2 c clock is generated by the master peripheral. the interface operates in master mode through the generation of the start condition: start bit set to 1 in the control register and i2c not busy (busy flag set to 0). once the start condition is sent, if interrupts are enabled, an event flag bit and a start bit are set by hardware. then the master waits for a read of the register used to observe bus activity (sr1 register) followed by a write in the data register dr with the slave address byte, holding the scl line low (see figure 11 transfer sequencing ev5). then the slave address byte is sent to the sda line via the internal shift register.
SPEAR-09-H022 6 ip description 43/55 after completion of these transfers, the event flag bit is set by hardware with interrupt generation. then the master waits for a read of the sr1 register followed by a write in the control register cr (for example set the peripheral enable bit), holding the scl line low (see figure 11 transfer sequencing ev6). next the master must enter receiver or transmitter mode. master receiver following the address transmission and after sr1 and cr registers have been accessed, the master receives bytes from the sda line into the dr register via the internal shift register. after each byte the interface generates in sequence: 1) acknowledge pulse if the acknowledge bit ack in the control register is set 2) event flag and the byte transfer finish bits are set by hardware with an interrupt. then the interface waits for a read of the sr1 register followed by a read of the dr register, holding the scl line low (see figure 11 transfer sequencing ev7). to close the communication: before reading the last byte from the dr register, set the stop bit to generate the stop condition. in order to generate the non-acknowledge pulse after the last received data byte, the ack bit must be cleared just before reading the second last data byte. master transmitter following the address transmission and after sr1 register has been read, the master sends bytes from the dr register to the sda line via the internal shift register. the master waits for a read of the sr1 register followed by a write in the dr register, holding the scl line low (see figure 11 transfer sequencing ev8). when the acknowledge bit is received, the interface sets event flag and the byte transfer finish bits with an interrupt. to close the communication: after writing the last byte to the dr register, set the stop bit to generate the stop condition. error cases berr: detection of a stop or a start condition during a byte transfer. in this case, the event flag and berr bits are set by hardware with an interrupt. af: detection of a non-acknowledge bit. in this case, the evf and af bits are set by hardware with an interrupt. to resume, set the start or stop bit. in all these cases, the scl line is not held low; however, the sda line can remain low due to possible 0 bits transmitted last. it is then necessary to release both lines by software.
6 ip description SPEAR-09-H022 44/55 figure 11. transfer sequencing legend: s=start, p=stop, a=acknowledge, na=non-acknowledge evx=event (with interrupt if ite=1) ev5: evf=1, sb=1, cleared by reading sr1 register followed by writing dr register. ev6: evf=1, cleared by reading sr1 register followed by writing cr register (for example pe=1). ev7: evf=1, btf=1, cleared by reading sr1 register followed by reading dr register. ev8: evf=1, btf=1, cleared by reading sr1 register followed by writing dr register. 6.12 general pourpose i/os the gpio block consists of 6 general purpose ios which act as buffers between the i/o pins and the processor core: data is stored in the gpio block and can be written to and read from by the processor via the apb bus. figure 12. gpio block diagram
SPEAR-09-H022 6 ip description 45/55 6.13 adc 6.13.1 overview the adc-apb bus controller provides connection between apb bus and st-adc8mux16 analog to digital converter: it handles the acquisition request from apb bus and generates control and configuration signals to drive adc and also the interrupt signal when acquisition is ready. for any adc input channel the controller can realize a single acquisition or an average up to 128 samples. there are two operating mode: normal mode: it handles all the digital ports of st-adc8mux16. test mode: the st-adc8mux16 is directly accessible by means of external pins as a stand-alone adc. this will allow stand-alone testing procedures (digital and analog) adc positive and negative reference voltages are supply by: ? positive vrefp_adc pin ? negative vrefn_adc pin 6.13.2 adc operating modes normal mode when the enable bit is set to 1, the conversion starts and as it finishes a bit of conversion ready (interrupt signal) is set to 1. at this point the reading of the data could begin and when it finishes, conversion ready and the enable bits becomes 0. in normal mode the signals accessible off-chip are listed in table 11 external pins of adc macro in normal mode. table 11. external pins of adc macro in normal mode test mode test mode is set by assigning the following logic state to the test pins: test0 0 test1 1 test2 0 test3 1 in this mode st-adc8mux16 is accessible for the testing procedure and its signals are switched to the following pins: signal direction description aid[15:0] input analog channels
6 ip description SPEAR-09-H022 46/55 table 12. external pads of adc macro in test mode 6.14 watchdog timer the wdt is based on a programmable 8 bit counter and generates a hot reset (single pulse) when it overflows. the timer should be cleared by the software before it overflows. the counter is clocked by a slow signal comi ng from a 21 bit prescaler clocked by the apb clock. so that, as apb bus has a frequency of 66.5 mhz, the maximum elapsing time is 8.07 second, while the minimum is 31.52 ms. the wdt is an apb slave device. 6.15 real time clock the real time clock block implements 3 functions: time-of-day clock in 24 hour mode calendar alarm time and calendar value are stored in binary code decimal format. date and time are stored in dedicated registers, so that the rtc can start to count the time. an alarm time can be defined and when the value of time and date is equal to the value on alarm registers, an interrupt is generated, if enabled. for debug the prescaler, that define the seconds, they can be bypassed to obtain a faster counter of the time. signal pin direction description test_out test_out output analog test point output test tx_en input test mode select start crs input start conversion en col input conversion enable clk rxd[0] input clock eoc scl output end of conversion d_0 rxd[1] output data output d_1 rxd[2] output data output d_2 rxd[3] output data output d_3 rx_dv output data output d_4 rx_er output data output d_5 mcd output data output d_6 mdio output data output d_7 sda output data output sel[0 to 3] tx[0 to 3] input selection line ? input analog mux
SPEAR-09-H022 6 ip description 47/55 a further option available is that if the seconds are masked, an interrupt for any second is generated. in the same way for minutes, hours, days, months or years. the rtc provides also a self-isolation mode, which allows it working even if power isn't supplied to the rest of the device. the rtc is an apb bus. 6.16 general pourpose timer spear head has 4 gpts, connected as apb bus slaves. a gpt is constituted by 2 channels and each one consists of a programmable 16 bit counter and a dedicated 8 bit timer clock prescaler. the programmable 8 bit prescaler unit performs a clock division by 1, 2, 4, 8, 16, 32, 64, 128, and 256, allowing a frequency range from 3.96 hz to 66.5 mhz. two modes of operation are available for each gpt: auto reload mode. when the timer is enabled, the counter is cleared and starts incrementing. when it reaches the compare register value, an interrupt source is activated, the counter first is automatically cleared and then restarts incrementing. the process is repeated until the timer is disabled. single shot mode. when the timer is enabled, the counter is cleared and starts incrementing. when it reaches the compare register value, an interrupt source is activated, the counter stopped and the timer disabled. the current timer counter value could be read from a register. 6.17 customizable logic 6.17.1 overview the customizable logic consists of an embedded macro where it is possible to map up to 200k equivalent asic gates. the logic is interfaced with the rest of the system so that it is possible to implement: ahb sub-systems with masters and slaves (via 1 ahb full master, 1 ahb full slave, 1 ahb master lite, 2 ahb slave ports) ahb master lite connected to dram controller ahb memories (via ahb slave ports) implemented by configuring the logic cells as sram elements. i/o protocol handlers (via the 112 dedicated gpio connections) 8 interrupt channels 8 dma requests 4 independent sram data channels (via dedicated connection to on-chip 16 kbyte sram) all of the above configuration scenarios can be mixed together in the same user-defined logic.
6 ip description SPEAR-09-H022 48/55 6.17.2 custom project development the custom project to design in the customizable logic can be implemented on an external fpga, which emulates easic logic cells. the purpose of this characteristic is allowing the user to develop his project both under real-time constraints and compliant to easic macrocell features. this mode is enabled by using the gpio interface, which is internally configured to support full- master and full-slave ahb ports. the figure 13 highlights the described behavior. in order to enable the "development mode", the configuration pin has to be set to state logic 1. after this configuration the logic implemented in the external fpga can completely interact with the following scenarios: ? ahb sub-systems with masters and slaves connected to the main system bus (full masters and full slaves peripherals) ? i/o protocol handlers (via 112 dedicated fpga i/os) ? 4 interrupt channels ? 4 dma requests all the above scenarios can be mixed in the same fpga configuration can be tested in order to verify the accordance with easic macrocell features, by running the arm926ej-s software debugger on a pc connected to spear head. once this test has been completed successfully, then the user-defined logic is ready to be moved without any additional changes within the on-chip easic configurable logic figure 13. emulation with external fpga 6.17.3 customization process the customization process requires two separate steps, executed at different times: 1. programming layer fabrication (single via-mask). 2. bitstream download. easic? ahb bus ahb bus custom design fpga configuration pad set to development mode spear? head
SPEAR-09-H022 6 ip description 49/55 the step 1 defines the interconnection between the customizable logic cells and is executed at fabrication level on top of the silicon wafers stored in the fab. the step 2 defines the logic function for each customizable logic cell and is executed after that the system has been powered up by dedicated software routines running on the arm926 microprocessor. both bitstream and via-mask realize the user-defined customization for the entire device. the easic mapping flow starts from the rtl description of the user-defined customization, with the purpose to generate the via-mask and configuration bitstream. 6.17.4 power on sequence once the system is powered-on, the easic logic has to be properly configured before its usage. in order to accomplish this task, two main operations have to be performed (both using dedicated software routines running on the arm9 microprocessor): 1 bitstream download 2 startup of connection between the easic macrocell and the rest of the device both steeps are driven by a control register programmable via apb bus. 6.17.5 bitstream download the bitstream download operation is responsible for the easic logic initialization, since each configurable cell of the customizable logic is loaded with a data stream that represents the mapped logic function. each operation of this download is performed by a dedicated software routine that read and writes data across the control register. the bitstream is a 32 kbyte data that is stored in the external non-volatile memory of the spear device. 6.17.6 connection startup once the easic logic is up and running due to the bitstream initialization, next steep is its reset, in order to allow connections to the other ips of the chip. the reset routine is activated by programming the control register. last steep is the enabling of needed connections, by setting the status register. 6.17.7 programming interface in order to achieve the bitstream download and the reset routine, a dedicate logic has been embedded in the spear head: the programming interface, which also includes the control register.
7 electrical characteristics SPEAR-09-H022 50/55 7 electrical characteristics 7.1 absolute maximum ratings this product contains devices to protect the inputs against damage due to high static voltages; however it is advisable to take normal precaution to avoid application of any voltage higher than the specified maximum rated voltages. table 13. absolute maximum rating values the average chip-junction temperature, tj, can be calculated using the following equation: t j = t a + (p d ja ) where : t a is the ambient temperature in c ja is the package junction-to-ambient thermal resistance, which is 34 c/w p d = p int + p port ?p int is the chip internal power ?p port is the power dissipation on input and output pins ; user determined if p port is neglected, an approximate relationship between p d is: p d = k / (tj + 273 c) and, solving first equations: k = p d (t a + 273 c) + ja x p d 2 k is a constant for the particular, which can be determined through last equation by measuring p d at equilibrium, for a know t a using this value of k, the value of p d and t j can be obtained by solving first and second equation, iteratively for any value of t a . symbol parameter value unit vdd core supply voltage core 2.1 v vdd i/o supply voltage i/o 6.4 v vdd pll supply voltage pll 6.4 v vdd sdr supply voltage sdram 6.4 v vdd ddr supply voltage ddr 5.4 v vdd rtc supply voltage rtc 2.1 v vi ttl input voltage ttl (3.3 and 5 v tollerant) 6.4 v vi sram input voltage sdram 6.4 v vi ddr input voltage ddr 5.4 v vi usbds input voltage usb (host and device) data signal interfaces 6.4 v vi usbrr input voltage usb reference resistor 6.4 v vi an analog input voltage adc 6.4 v tj junction temperature -40 to 125 c tstg storage temperature -55 to 150 c
SPEAR-09-H022 7 electrical characteristics 51/55 7.2 dc elettrical characteristics 7.2.1 supply voltage specifications the recommended operating conditions are listed in the following table: table 14. recommended operating conditions 7.2.2 i/o voltage specifications 7.2.2.1 lvttl i/o (c0mpliiant with eia/jedec standard jesd8-b) for lvttl (3.3 and 5 v tolerant) pins, the allowed i/o voltages are: table 15. low voltage ttl dc input specification (3 < vdd < 3.6) table 16. low voltage ttl dc output specification (3 < vdd < 3.6) * x is the source / sink current under worst case conditions and it is reflected in the na me of the i/o cell according to the drive capability. table 17. pull-up and pull-down characteristics symbol description min. typ. max. unit vdd core supply voltage core 1.14 1.2 1.26 v vdd i/o supply voltage i/o 3 3.3 3.6 v vdd pll supply voltage pll 3 3.3 3.6 v vdd sdr supply voltage sdram 3 3.3 3.6 v vdd ddr supply voltage ddr 2.3 2.5 2.7 v vdd rtc supply voltage rtc 1.14 1.2 1.26 v top operating temperature -40 85 c symbol parameter test condition min. max. unit vil low level input voltage 0.8 v vih high level input voltage 2 v vhyst schmitt trigger hysteresis 0.495 0.620 v symbol parameter test condition min. max. unit vol low level output voltage iol = x ma * 0.15 v voh high level output voltage ioh = x ma * vdd - 0.15 v symbol parameter test condition min. typ. max. unit ipu pull-up current vi = 0 v 40 60 110 a ipd pull-down current vi = vdd 30 60 133 a rup equivalent pull-up resistance vi = 0 v 32 50 75 kohm rpd equivalent pull-down resistance vi = vdd 27 50 100 kohm
7 electrical characteristics SPEAR-09-H022 52/55 7.2.2.2 lvcmos/sstl i/o if the i/os are set as lvcmos (for sdram memories), the dc electrical characteristics are the following: table 18. lvcmos dc input specification (3 < vdd < 3.6) table 19. lvcmos dc output specification (3 < vdd < 3.6) instead when they are set as (for ddr memories), refer to following tables: table 20. dc input specification of bidirectional sstl pins (2.3 < vdd ddr < 2.7) table 21. dc input specification of bidirectional differentialsstl pins (2.3 < vdd ddr < 2.7) symbol parameter test condition min. max. unit vil low level input voltage vout voh (min) or vout vol (max) -0.3 0.8 v vih high level input voltage 2 vdd+0.3 v iin input current vin = 0 or vin =vdd 5 a symbol parameter test condition min. max. unit vol low level output voltage vdd = min, iol = 100 a 0.2 v voh high level output voltage vdd = min, ioh = -100 a vdd - 0.2 v symbol parameter min. max. unit vil low level input voltage -0.3 sstl_vref ? 0.15 v vih high level input voltage sstl_vref + 0.15 vdd ddr ? 0.15 v symbol parameter min. max. unit vil low level input voltage -0.3 vdd ddr + 0.3 v vih high level input voltage 0.36 vdd ddr ? 0.6 v
SPEAR-09-H022 8 package information 53/55 8 package information in order to meet environmental requirements, st offers these devices in ecopack ? packages. these packages have a lead-free second level interconnect. the category of second level interconnect is marked on the package and on the inner box label, in compliance with jedec standard jesd97. the maximum ratings related to soldering conditions are also marked on the inner box label. ecopack is an st trademark. ecopack specifications are available at: www.st.com. figure 14. pbga420 mechanical data & package dimensions outline and mechanical data dim. mm inch min. typ. max. min. typ. max. a 2.16 0.085 a1 0.30 0.012 a2 1.53 0.060 b 0.50 0.60 0.70 0.020 0.024 0.027 d 22.80 23.00 23.20 0.8976 0.905 0.913 d1 21.00 0.827 d2 20.00 0.787 e 22.80 32.00 23.20 e1 21.00 e2 20.00 e 1.00 0.039 f 1.00 0.039 ddd 0.20 0.008 eee 0.25 0.010 fff 0.10 0.004 pbga420 (23x23x2.16mm) ball grid array package 7740354 a
SPEAR-09-H022 54/55 9 revision history date revision changes 17-oct-2005 1 initial release. 1-dec-2005 2 changed the part number from spear-09-h020 to SPEAR-09-H022. modified/added some dates in the chapter 7.
SPEAR-09-H022 55/55 information furnished is believed to be accurate and reliable. however, stmicroelectronics assumes no responsibility for the co nsequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of stmicroelectronics. specifications mentioned in this publicati on are subject to change without notice. this publication supersedes and replaces all information previously supplied. stmicroelectronics prod ucts are not authorized for use as critical components in life support devices or systems without express written approval of stmicroelectro nics. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners ? 2005 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of SPEAR-09-H022

	To Download SPEAR-09-H022 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .