features * ideal for printed circuit board maximum ratings and electrical characteristics ratings at 25 o c ambient temperature unless otherwise specified. single phase, half wave, 60hz, resistive or inductive load. for capacitive load, derate current by 20%. dimensions in inches and (millimeters) voltage range - 50 to 1000 volts current - 2.0 amperes rectifier specialists r dc components co., ltd. technical specifications of single-phase silicon bridge rectifier mechanical data * case: molded plastic * epoxy: ul 94v-0 rate flame retardant * terminals: mil-std-202e, method 208 guaranteed * polarity: symbols molded or marked on body HBL2A thru hbl2m * mounting position: any * surge overload rating: 50 amperes peak hbl .060(1.5).045(1.1) .080(2.0).065(1.7) .125(3.2) 45o chamfer .81(20.6).77(19.6) .095(2.4).065(1.6) .44(11.2) .42(10.7) .209(5.3).189(4.8) spacing ac .187(4.7).148(3.8) .045(1.1).035(0.9) .68(17.3).62(15.7) .020(0.5).015(0.4) maximum recurrent peak reverse voltage maximum rms bridge input voltage maximum dc blocking voltage maximum average forward output current at t a = 50 o c peak forward surge current 8.3 ms single half sine-wave superimposed on rated load (jedec method) symbol v rrm v dc i o i fsm v rms volts volts amps 2.0 amps units volts maximum dc reverse current at rated dc blocking voltage per element v f i r 1.0 500 maximum forward voltage drop per element at 1.0a dc volts @t a = 25 o c @t a = 100 o c 10 mamps i2t rating for fusing (t*8.3ms) i2t 93 a2sec typical junction capacitance ( note1) cj 40 pf typical thermal resistance (note 2) rqja 19 0c/w notes : 1. measured at 1 mh z and applied reverse voltage of 4.0 volts 2.thermal resistance from junction to case per element unit mounted on 300x300x1.6mm aluminum plate heat-sink. operating temperature range t j -55 to +150 0 c stg 0 storage temperature range t -55 to +150 0 c 50 HBL2A hbl2b hbl2d hbl2g hbl2j hbl2k hbl2m 50 100 200 400 600 800 1000 35 70 140 280 420 560 700 50 100 200 400 600 800 1000
r dc components co., ltd. rating and characteristic curves (HBL2A thru hbl2m) single phase half wave 60hz inductive or resistive load case temperature, ( oc) 0 50 100 150 fig. 2 - typical forward current derating curve 5 4 3 2 1 average forward output current, (a) fig. 1 - maximum non-repetitive forward surge current peak forward surge current, (a) number of cycles at 60hz 1 2 5 10 20 50 100 0 250 200 150 100 50 8.3ms single half sine-wave (jedec mathod) 300 instantaneous forward voltage, (v) .6 .8 1.0 1.2 1.4 2.0 pulse width=300ms1% duty cycle fig. 3 - typical instantaneous forward characteristics 100 10 1 .1 1.8 1.6 instantaneous forward current, (a) tj=25oc percent of rated peak reverse voltage, (%) 0 20 40 60 80 100 120 140 fig. 4 - typical reverse characteristics 10 1.0 .1 .01 instantaneous reverse current, ( ma) tj=25oc tj=100oc
|
