mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. october 2006 - rev 19-oct-06 mimix broadband ? s 36.0-42.0 ghz gaas transmitter has a +17.0 dbm output third order intercept across the band. this device is a balanced, resistive phemt mixer followed by a distributed output amplifier and includes an integrated lo doubler and lo buffer amplifier. the use of integrated lo doubler and lo buffer amplifier makes the provision of the lo easier than for fundamental mixers at these frequencies. i and q mixer inputs are provided and an external 90 degree hybrid is required to select the desired sideband. this device uses mimix broadband ? s 0.15 m gaas phemt device model technology, and is based upon electron beam lithography to ensure high repeatability and uniformity. this device is well suited for millimeter-wave point-to-point radio, lmds, satcom and vsat applications. 36.0-42.0 ghz gaas transmitter qfn, 7x7 mm electrical characteristics (ambient temperature t = 25 o c) page 1 of 8 sub-harmonic, image reject transmitter integrated mixer, lo doubler/buffer & output amplifier +17.0 dbm output third order intercept (oip3) +2.0 dbm lo drive level 5.0 db conversion gain 100% rf and dc testing features units ghz ghz ghz ghz db db dbm dbm dbm dbm vdc vdc vdc vdc ma ma min. 36.0 36.0 16.0 dc - - - - - - - - - -2.0 - - typ. - - - - 10.0 5.0 +2.0 -25.0 -10.0 +17.0 +4.0 -0.4 -0.5 - 240 0.0 max. 42.0 42.0 26.0 4.0 - - - - - - - - - 0.0 - - parameter frequency range (rf) upper side band frequency range (rf) lower side band frequency range (lo) frequency range (if) output return loss rf (s22) small signal conversion gain if/rf (s21) lo input drive (p lo ) leakage @ rf port lox1 leakage @ rf port lox2 output third order intercept (oip3) drain bias voltage (vd) gate bias voltage (vg1) gate bias voltage (vg2) mixer, doubler dynamic range control (vc) supply current (id) (vd=4.0v) supply current (ic) (1) measured using constant current. (2) measured using lo input drive level of +2.0 dbm. 1,2 2 general description absolute maximum ratings supply voltage (vd) supply current (id) gate bias voltage (vg) input power (pin) storage temperature (tstg) operating temperature (ta) channel temperature (tch) esd - human body model esd - machine body model +6.0 vdc 350 ma +0.3 vdc +0.0 dbm -65 to +165 deg c -55 to mttf table 1 mttf table 1 class 1a class m1 (1) channel temperature affects a device?s mttf. it is recommended to keep channel temperature as low as possible for maximum life u1006-qb
36.0-42.0 ghz gaas transmitter qfn, 7x7 mm page 2 of 8 transmitter measurements mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. xu1006-qb, usb conv. gain (db) and image rejection (dbc) -25 -20 -15 -10 -5 0 5 10 36 37 38 39 40 41 42 rf usb (ghz) [if=2 ghz] cg (db) and ir (dbc) conv gain image rej xu1006-qb, lsb conv. gain (db) and image rejection (dbc) -25 -20 -15 -10 -5 0 5 10 36 37 38 39 40 41 42 rf lsb (ghz) [if=2 ghz] cg (db) and ir (dbc) conv gain image rej xu1006-qb, 1xlo to rf leakage (dbm), p_lo=+2dbm -30 -25 -20 -15 -10 -5 0 17.0 17.5 18.0 18.5 19.0 19.5 20.0 20.5 lo (ghz) 1xlo to rf leakage (dbm) xu1006-qb, 2xlo to rf leakage (dbm), p_lo=+2dbm -30 -25 -20 -15 -10 -5 0 17.0 17.5 18.0 18.5 19.0 19.5 20.0 20.5 lo (ghz) 2xlo to rf leakage (dbm) rfout-2xlo (dbc) vs. lo freq p_lo=+2 dbm, if_in=-10dbm 0 5 10 15 20 25 17.0 17.5 18.0 18.5 19.0 19.5 20.0 20.5 lo freq (ghz) rfout-2xlo (dbc) xu1006-qb, output ip3 (dbm) 0 2 4 6 8 10 12 14 16 18 20 36 37 38 39 40 41 42 rf (ghz) oip3 (dbm) usb lsb october 2006 - rev 19-oct-06 u1006-qb
36.0-42.0 ghz gaas transmitter qfn, 7x7 mm page 3 of 8 transmitter measurements (cont.) mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. xu1006-qb, input ip3 (dbm) 0 2 4 6 8 10 12 14 16 18 36 37 38 39 40 41 42 rf (ghz) iip3 (dbm) usb lsb xu1006-qb, conv gain and iip3 vs vc (dynamic range) rf=38ghz, if=2ghz, p_if=-3dbm/tone -30 -25 -20 -15 -10 -5 0 5 10 15 20 -2.0 -1.8 -1.6 -1.4 -1.2 -1 .0 -0.8 -0.6 -0.4 -0.2 0.0 vc (v) cg (db) and iip3 (dbm) cg @ usb cg @ lsb iip3 @ usb iip3 @ lsb october 2006 - rev 19-oct-06 u1006-qb
36.0-42.0 ghz gaas transmitter qfn, 7x7 mm page 4 of 8 physical dimensions mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. package pin-out table functional schematic balanced image reject mixer x2 lo buffer 1 2 3 4 5 6 7 8 9 10 11 12 13 14 21 20 19 18 17 16 15 28 27 26 25 24 23 22 rf out lo in gnd gnd gnd gnd vg1 vg2 vd gnd gnd if2 if1 gnd gnd pa vc pin number pin name pin function nominal value unit 4 rf out rf out 7 vc gain control -2.0 to 0.0 volts 8 vg1 lna, lo amp -0.4 volts 9 vg2 mixer, doubler -0.5 volts 11 if2 if2 input 18 lo in lo input +2.0 dbm 25 if1 if1 input 27 vd1 drain bias +4.0 volts all other pins gnd ground october 2006 - rev 19-oct-06 u1006-qb
36.0-42.0 ghz gaas transmitter qfn, 7x7 mm page 5 of 8 recommended layout mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. october 2006 - rev 19-oct-06 u1006-qb environmental msl - gross test leak compliant
36.0-42.0 ghz gaas transmitter qfn, 7x7 mm page 6 of 8 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. mttf mttf is calculated from accelerated life-time data of single devices and assumes an isothermal back-plate. app note [1] biasing - app note [1] biasing - the device is operated by biasing vd=4.0v with id=240ma. additionally, a mixer and doubler bias are also required with vg2=-0.5v. adjusting vg2 above or below this value can adversely affect conversion gain, image reje ction and intercept point performance. the vc bias pin controls an integrated attenuator where vc=-1.3 v provides the minimum attenuation and vc = 0.0 v provides the maximum attenuation (approximately 25 db). it is recommended to use active biasing to keep the currents constant as the rf power and temperature vary; this gives the most reproducible results. depending on the supply voltage available and the power dissipation constraints, the bias circuit may be a single transistor or a low power operational amplifier, with a low value resistor in series with the drain supply used to sense the cu rrent. the gate of the phemt is controlled to maintain correct drain current and thus drain voltage. the typical gate voltage needed to do this i s vg1= -0.4v. typically the gate is protected with silicon diodes to limit the applied voltage. also, make sure to sequence the applied volta ge to ensure negative gate bias is available before applying the positive drain supply. typical application mimix broadband's 36.0-42.0 ghz xu1006-qb gaas transmitter can be used in saturated radio applications and linear modulation schemes up to 128 qam. the transmitter can be used in upper and lower sideband applications from 36.0-42.0 ghz. mixer mimix broadband mmic-based 35.0-45.0 ghz transmitter block diagram (changing lo and if frequencies as required allows design to operate as high as 42 ghz) rf out 37.0-39.5 ghz xu1006-qb xp1005 coupler if in 2 ghz lo(+2.0dbm) 17.5-18.75 ghz (usb operation) 19.5-20.75 ghz (lsb operation) buffer x2 x xu1006-qb, mttf (yrs) vs. backplate temperature (c) 1.0e+00 1.0e+01 1.0e+02 1.0e+03 1.0e+04 1.0e+05 55 65 75 85 95 temperature (c) mttf (years) bias conditions: vd=4.0v, id=240 ma october 2006 - rev 19-oct-06 u1006-qb
36.0-42.0 ghz gaas transmitter qfn, 7x7 mm page 7 of 8 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. app note [3] usb/lsb selection - usb lsb if1 if2 an alternate method of selection of usb or lsb: for lower side band operation (lsb): with if1 and if2 connected to the direct port (0o) and coupled port (90o) respectively as shown in the diagram, the lsb signal will reside on the input port. the isolated port must be loaded with 50 ohms. with if1 and if2 connected to the direct port (0o) and coupled port (90o) respectively as shown in the diagram, the usb signal will reside on the isolated port. the input port must be loaded with 50 ohms. for upper side band operation (usb): -90 o in phas e combiner usb in phas e combiner lsb -90 o if2 if1 if2 if1 factory automation and identification mimix designator -qb package type qfn (7x7mm) p 1 component pitch 12mm p 0 hole pitch 4mm w tape width 16mm number of leads offered 28 reel diameter 329mm (13in) units per reel 1000 tape and reel packaging per the following conditions: tape width: 16 mm tape pitch (part to part): 12 mm component orientation: parts are to be oriented with the pin 1 closest to the tape's round sprocket holes on the tape?s trailing edge. reel diameter: 329 mm (13 inch) note: tape and reel packaging is ordered with a -000t suffix. package is available in 500 unit reels through designated sales c hannels. minimum order quantities should be discussed with your local sales representative. october 2006 - rev 19-oct-06 u1006-qb
36.0-42.0 ghz gaas transmitter qfn, 7x7 mm page 8 of 8 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. caution! - mimix broadband mmic products contain gallium arsenide (gaas) which can be hazardous to the human body and the environment. for safety, observe the following procedures: do not ingest. do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed. observe government laws and company regulations when discarding this product. this product must be discarded in accordance with methods specified by applicable hazardous waste procedures. life support policy - mimix broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the president and general counsel of mimix broadband. as used herein: (1) life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) a critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to aff ect its safety or effectiveness. package attachment - this packaged product from mimix broadband is provided as a rugged surface mount package compatible with high volume solder installation. the package is a low-cost plastic package. vacuum tools or other suitable pick and place equipment may be used to pick and place this part. care should be taken to ensure that there are no voids or gaps in the solder connection so that good rf, dc and ground connections are maintained. voids or gaps can eventually lead not only to rf performance degradation, but reduced reliability and life of the product due to thermal stress. mimix lead-free rohs compliant program - mimix has an active program in place to meet customer and governmental requirements for eliminating lead (pb) and other environmentally hazardous materials from our products. all mimix rohs complian t components are form, fit and functional replacements for their non-rohs equivalents. lead plating of our rohs compliant parts i s 100% matt tin (sn) over copper alloy and is backwards compatible with current standard snpb low-temperature reflow processes as well as higher temperature (260c reflow) ?pb free? processes. part number for ordering description XU1006-QB-0L00 ni/pd/au plated rohs compliant qfn 7x7 28l surface mount package in bulk quantity xu1006-qb-0l0t ni/pd/au plated rohs compliant qfn 7x7 28l surface mount package in tape and reel xu1006-qb-ev1 xu1006-qb evaluation module we also offer this part with alternative plating options. please contact your regional sales manager for more information regar ding different plating types. reflow profile ramp up rate activation time and temperature time above melting point max peak temperature time within 5 oc of peak ramp down rate snpb 3-4 oc/sec 60-120 sec @ 140-160 oc 60-150 sec 240 oc 10-20 sec 4-6 oc/sec pb free 3-4 oc/sec 60-180 sec @ 170-200 oc 60-150 sec 265 oc 10-20 sec 4-6 oc/sec october 2006 - rev 19-oct-06 u1006-qb
|
