GFE1300-547 1300 nm edge emitting led outline dimensions in inches (mm) description st is a registered trademark of at & t. the GFE1300-547 is a high performance 1300 nm edge emitting led specifically designed for coupling high power into monomode optical fibers. when pulsed at 100ma typical coupled power into 9/125 m fiber is 15 w. bandwidth is typically 200 mhz. where applicable, standard pin orientation aligns pin 2 with the receptacle keyway. this orientation will be supplied unless requested otherwise. the heatsink tab is removed to allow alignment in some receptacles. this device is very susceptible to damage by electrostatic discharge. all dimensions are in millimetres. tolerances are 0.10 mm unless otherwise stated. receptacle illustrated with typical active device installed. high precision ceramic bore. device alignment to fibre tested with at&t st2 connector. features typically 15 w into 9/125 m fibre with 1ms pulse at 100 ma pulse at 100 ma spectral width 60 nm bandwidth of 200 mhz operating temperature-10?c to +65?c odim_234.tif opho_229.doc pinout 1. cathode 2. anode 3. case honeywell reserves the right to make changes in order to improve design and supply the best products possible. 240 h
GFE1300-547 1300 nm edge emitting led typ min units t est condition s parameter symbol max electro-optical characteristics i? = 100 ma power ( 9/125 m na0.11 ) p???? w 815 1ms p ulse power ( 50/125 m na 0.20 ) 40 50 power ( 62.5/125 m na 0.27 ) 70 i? = 100 ma peak emission wavelen g th ?? nm 1270 1300 1330 i? = 100 ma s p ectral width between half p ower p oint ? nm 60 100 = 100 ma +20 ma p- -3db bandwidth f mhz 200 i? = 100 ma forward volta g e v? v 1.6 2.0 [] connectorised p ower re p eatabilit y db 1.5 notes 1. applies to 9/125 m fibre terminated with a recommended ceramic ferrule in group b receptacles. typ min units t est condition s parameter symbol max limiting values continuous forward current i? ma 110 50% dut y c y cle re p etitive p eak forward current i??? ma 150 reverse volta g e v? v 1.0 o p eratin g tem p erature t? ?c -10 +65 stora g e tem p erature t??? ?c -40 +65 2 mm form solderin g tem p erature t? ?c the case for 10 s 260 typ min units t est condition s parameter symbol max thermal characteristics radiant p ower tem p erature coefficient dp/dt %/?c -3.5 wavelen g th tem p erature coefficient d?/dt nm/?c 0.8 absolute maximum ratings (25?c free-air temperature unless otherwise noted) -55 to +100?c storage temperature -40 to +100?c case operating temperature 260?c, 10s lead solder temperature 100 ma continuous forward current (heat sinked) 1 v @ 10 a reverse voltage stresses greater than those listed under "absolute maximum ratings" may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods of time may affect reliability. honeywell reserves the right to make changes in order to improve design and supply the best products possible. h 241
GFE1300-547 1300 nm edge emitting led description catalog listing order guide GFE1300-547 1300 nm surface emitting led the inherent design of this component causes it to be sensitive to electrostatic discharge (esd). to prevent esd-induced damage and/or degradation to equipment, take normal esd precautions when handling this product. c a u ti o n fig. 1 ogra_159.tif fig. 2 ogra_160.tif fig. 3 ogra_161.tif honeywell reserves the right to make changes in order to improve design and supply the best products possible. 242 h
|
