 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Voltage Variable Absorptive Attenuator, 20 dB AT-309 DC - 2 GHz V 2.00 Features q q q q q q q q SO-8 20 dB Voltage Variable Attenuation Very Low Power Consumption: 50 W Low Intermodulation Products Dual Voltage Control 0 to -4 Volts Nanosecond Switching Speed Temperature Range: -40C to +85C Low Cost SOIC8 Plastic Package Tape and Reel Packaging Available1 Description M/A-COM's AT-309 is a GaAs MMIC voltage variable absorptive attenuator in a low cost SOIC 8-lead surface mount plastic package. The AT-309 is ideally suited for use where attenuation fine tuning, fast switching and very low power consumption are required. Typical applications include radio, cellular, and GPS equipment and other Automatic Gain/Level Control circuits. The AT-309 is fabricated with a monolithic GaAs MMIC using a mature 1-micron process. The process features full chip passivation for increased performance and reliability. Ordering Information Part Number AT-309 PIN AT-309TR AT-309RTR Package SOIC 8-Lead Plastic Package Forward Tape & Reel Reverse Tape & Reel Electrical Specifications, TA = +25C Parameter Insertion Loss Test Conditions2 DC - 0.1 GHz DC - 0.5 GHz DC - 1.0 GHz DC - 2.0 GHz DC - 0.1 GHz DC - 0.5 GHz DC - 1.0 GHz DC - 2.0 GHz 10% to 90% RF, 90% to 10% RF 50% Control to 90% RF, 50% Control to 10% RF In Band Input Power (Over Attenuation Range) Measured Relative (Over Attenuation Range) to Input Power (Over Attenuation Range) (for two-tone input power up to +5 dbm) Measured Relative (Over Attenuation Range) to Input Power (Over Attenuation Range) (for two-tone input power up to +5 dbm) 0.05 GHz 0.5 - 2.0 GHz 0.05 GHz 0.5 - 2.0 GHz Unit dB dB dB dB dB dB dB dB nS nS mV dBm dBm dBm dBm dBm Min. Typ. 0.7 0.8 0.9 1.2 +/-0.5 +/-0.5 +/-0.8 +/-1.0 1.4:1 6 8 10 5 47 40 39 32 Max 0.9 1.0 1.2 1.4 +/-0.8 +/-0.8 +/-1.0 +/-1.2 Flatness (Peak to Peak) VSWR (Matched) Trise, Tfall Ton, Toff Transients One dB Compression IP2 IP3 1.Refer to "Tape and Reel Packaging"Section, or contact factory. 2.All measurements at 1 GHz in a 50 system, unless otherwise specified.The A and B control voltages vary 0 to -4V @ 20 A typ. Powered by ICminer.com Electronic-Library Service CopyRight 2003 Voltage Variable Absorptive Attenuator, 20 dB Absolute Maximum Ratings1 Parameter Max. Input Power 50 MHz 500-2000 MHz Control Voltage Operating Temperature Storage Temperature Absolute Maximum +27 dBm +30 dBm +5V, -8.5V -40C to +85C -65C to +150C AT-309 V 2.00 Functional Schematic 1.Operation of this device above any one of these parameters may cause permanent damage. Electrical Schematic RF 1 Q1 Q3 RF 2 Pin Configuration Pin No. Description GND RF1 GND A B GND RF2 GND 1 2 3 4 5 6 7 8 Q2 A B Typical Performance Powered by ICminer.com Electronic-Library Service CopyRight 2003 |
Price & Availability of AT-309RTR
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |