View HY-1602H-803_149049.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

C-7 :(086)0755-26919178 : (086)0755 -26911092 Http://www.av-display.com.cn
SHENZHEN AV-DISPLAY CO.,LTD Address: North East C-7 Building, Wenchang Street Eastern District, OCT, ShenZhen, China TEL: (086)0755-26919178 FAX: (086)0755-26911092
Http://www.av-display.com.cn
www..com
SPECIFICATION FOR LCM MODULE
MODULE NO.: HY-1602H-803 DOC.REVISION: 00
Customer Approval:
SIGNATURE PREPARED BY (RD ENGINEER) PREPARED BY (QA ENGINEER) CHECKED BY APPROVED BY
DATE Oct-13-2005
DOCUMENT REVISION HISTORY
Version 00 DATE Oct-13-2005 DESCRIPTION First issue CHANGED BY
www..com
CONTENTS
1. Functions & Features 2. Mechanical specifications 3. Block diagram 4. Dimensional Outline
www..com 5. Pin description
1 1 1 2 3 3 4~5 6 7 8 8 9~17
6. Maximum absolute limit 7. Electrical characteristics 8. Control and display command 9. Character Generator Rom 10. Backlight characteristics 11.Electrol-Optical characteristics 12. Quality Specifications
1. FUNCTIONS & FEATURES
1.1. Format 1.2. LCD mode 1.3. Viewing direction 1.4. Driving scheme 1.5. Power supply voltage (VDD) 1.6. LCD driving voltage(Vop) 1.7. Operation temp 1.8. Storage temp 1.9. Backlight color 2.0. Driver IC
www..com
: 16x2 characters : STN / Negative Transmissive Mode / Blue : 6 o'clock : 1/16 Duty , 1/5 Bias : 5.0V : 4.2V : -20~70 : -30~80 : White : S6A0069X01-COCX
2. MECHANICAL SPECIFICATIONS
2.1. Module size 2.2. Viewing area 2.3 Character pitch 2.4 Character size 2.5. Dot pitch 2.6. Dot size 2.7. Weight : 85.0mm(L)*30.0mm(W)*13.4max mm(H) : 65.0mm(L)*17.2mm(W) : 3.65mm(L)*5.05mm(W) : 2.95mm(L)*4.35mm(W) : 0.60mm(L)*0.55mm(W) : 0.55mm(L)*0.50mm(W)
: Approx.
3. BLOCK DIAGRAM
VSS VDD Vo RS E R/W DB0-DB7
LEDA LEDK
CONTROL LSI S6A0069X01
LCD Panel LCD MODULE Backlight
VDD(+5.0V) Vo VR(0~20K) VSS(0V) LEDA(+5.0V) LEDK(0V)
Figure1. Block diagra
1
www..com
14 13
B
300.3 16 24 17.2(V.A)
4. DIMENSIONAL OUTLINE
A
K
21
41.
9.4(A.A)
81 850.3
Figure 2. Dimensional outline
0.60 0.55
1 2
C
PIN 1 2 3 4 5 6 7 CONNECTOR VDD VSS V0 RS R/W E DB0 9 10 11 12 13 14 PIN 8 CONNECTOR DB1 DB2 DB3 DB4 DB5 DB6 DB7
0.55 0.50
SCALE:
D
2.95 3.65
PART NO:
FAV-HY-1602H-803-02
1
2
3
4
5 .2 R1
0
7.9
2
57.7(A.A)
4-
2
2 4
REV A00 A01 A02 DESCRIPTION First issue 1 Change IC chance 2 Change LED color DATE MAY-24-2005 MAY-25-2005 MAY-26-2005
1
3
5 6
A
730.2 65(V.A) 2 10.6 13.4(MAX)
A
6.5
2.54
B
(P2.54X6) 15.24 4.35 5.05
PROJECTION
270.2
14 -
1.6
1. 0
C
FIT
SHEET:
MODEL NUMBER
1
GENERAL TOL: APPROVALS
OF 0.3
1
UNIT mm DATE
D
HY-1602H-803
DO NOT SCALE THIS DRAWING.
APP: CHK: DWN:
5
6
5. PIN DESCRIPTION
No. 1 2 3 4 5 6 7~14 A K www..com Symbol VDD VSS V0 RS R/W E D0~D7 LEDA LEDK Function Power supply for Logic(+5V) GND(0V) Power supply for LCD drive Register selection (H:Data registor, L:Instruction registor) Read/write selection (H:Read,L:Write) Enable signal for LCM Data Bus line Power supply for Blacklight(+5V) Power supply for Blacklight(0V)
6. MAXIMUM ABSOLUTE LIMIT
NOTE: Voltage greater than above may damage the circuit. VDD >V1 > V2 > V3 >V4 > V5
3
7. ELECTRICAL CHARACTERISTICS
7.1 DC CHARACTERISTICS (VDD = 4.5V ~ 5.5V, Ta = -30 ~ +85)
www..com
4
7.2 AC Characteristics (VDD = 4.5V ~ 5.5V, Ta = -30 ~ +85)
www..com
Figure 6. Write Mode Timing Diagram
Figure 7. Read Mode Timing Diagram
5
8. CONTROL AND DISPLAY INSTRUCTION
www..com
NOTE: When an MPU program with checking the Busy Flag (DB7) is made, it must be necessary 1/2 Fosc is necessary for executing the next instruction by the falling edge of the 'E' signal after the Busy Flag (DB7) goes to "Low".
6
9. Character Generator Rom
www..com
7
10.BACK LIGHT CHARACTERISTICS
LCD Module with side LED Backlight ELECTRICAL RATINGS Ta = 25C
Item Forward Voltage Reverse Current Luminous Intensity (With LCD dots off) Wave length Color www..com Symbol Condition Min Typ Max Unit
VF IR IV
IF=30mA VR=0.8V IF=30mA IF=30mA
3.8 --151
4.0 35 201
4.2 -------
V mA Cd/m2 nm
----White
11. ELECTRO-OPTICAL CHARACTERISTICS
( VOP = 4.2V, Ta = 25C ) Item Symbo l Operating Voltage Response time Contrast Viewing angle range Vop Tr Tf Cr Condition Ta = -20C Ta = 25C Ta = 70C Ta = 25C Ta = 25C Cr2 Min 4.5 4.0 3.5 -------40 -40 Typ 4.7 4.2 3.7 185 200 4.2 ----Max 4.9 4.5 3.9 ------+40 +40 Unit V ms ms --deg deg
8
12.QUALITY SPECIFICATIONS
12.1 Standard of the product appearance test
Manner of appearance test: The inspection should be performed in using 20W x 2 fluorescent lamps. Distance between LCM and fluorescent lamps should be 100 cm or more. Distance between LCM and inspector eyes should be 30 cm or more. Viewing direction for inspection is 45 from vertical against LCM.
www..com
Fluorescent Lamps 30cm
o 45 o 45 min
100cm min
LCD LCM
Definition of zone:
A Zone B Zone
A Zone: Active display area (minimum viewing area). B Zone: Non-active display area (outside viewing area).
12.2 Specification of quality assurance
AQL inspection standard Sampling method: MIL-STD-105E, Level II, single sampling
9
Defect classification (Note: * is not including)
Classify Major Display state Item Short or open circuit LC leakage Flickering No display Wrong viewing direction
www..com
Note 1
AQL 0.65
Contrast defect (dim, ghost) Back-light Non-display Flat cable or pin reverse Wrong or missing component
2 1,8 10 11 2 3 4 5 6 7 12 3 9 10 13 1.0
Minor
Display state
Background color deviation Black spot and dust Line defect, Scratch Rainbow Chip Pin hole Protruded
Polarizer Soldering Wire TAB
Bubble and foreign material Poor connection Poor connection Position, Bonding strength
10
Note on defect classification
No. 1 Item Short or open circuit LC leakage Flickering No display
www..com
Criterion Not allow
Wrong viewing direction Wrong Back-light
2
Contrast defect Background color deviation
Refer to approval sample
3
Point defect, Black spot, dust (including Polarizer)
Y X
Point
Size <0.10 0.10<0.20 0.20<0.25 0.25<0.30 >0.30
Acceptable Qty.
Disregard 3 2 1 0
= (X+Y)/2
Unitmm 4 Line defect, Scratch
W L
Line
L W --0.015W 3.0L 0.03W 2.0L 0.05W 1.0L 0.1W
--0.05Acceptable Qty.
Disregard 2 1
Applied as point defect
Unit: mm 5 Rainbow Not more than two color changes across the viewing area.
11
No 6 Chip
Item
Criterion Acceptable criterion X Y t
2
0.5mm
X
Remark: X: Length direction Y: Short direction
www..com
Y
Z
t/2
Z
Z: Thickness direction t: Glass thickness W: Terminal Width
Z
X
Y
Acceptable criterion X Y
2
0.5mm
Z
t
Acceptable criterion X Y Y X
3 2 shall not reach to ITO
Z
t
W
Y
Acceptable criterion X Y Z
Disregard 0.2
Z
t
X
Y
Acceptable criterion X Y
5 2
Z
t/3
X
Z
12
No. 7
Item Segment pattern W = Segment width = (X+Y)/2 (1) Pin hole
Criterion
< 0.10mm is acceptable. X
X
Point Size
Acceptable Qty
Disregard 1 0
Y
www..com
W 8 9 Back-light Soldering
1/4W Y 1/4W< 1/2W 1/2W
Unit: mm
(1) The color of backlight should correspond its specification. (2) Not allow flickering (1) Not allow heavy dirty and solder ball on PCB. (The size of dirty refer to point and dust defect) (2) Over 50% of lead should be soldered on Land.
Lead Land
50% lead
10 Wire (1) Copper wire should not be rusted (2) Not allow crack on copper wire connection. (3) Not allow reversing the position of the flat cable. (4) Not allow exposed copper wire inside the flat cable. 11* PCB (1) Not allow screw rust or damage. (2) Not allow missing or wrong putting of component.
13
No 12
Item Protruded W: Terminal Width
W
Criterion
Acceptable criteria:
Y
Y 0.4
X
www..com
13
TAB
1. Position
W H H1 TAB W1 ITO W11/3W H11/3H
2 TAB bonding strength test F
TAB
P (=F/TAB bonding width) 650gf/cm ,(speed rate: 1mm/min) 5pcs per SOA (shipment)
14
Total no. of acceptable Defect
A. Zone Maximum 2 minor non-conformities per one unit. Defect distance: each point to be separated over 10mm B. Zone It is acceptable when it is no trouble for quality and assembly in customer's end product.
14
12.3 Reliability of LCM
Reliability test condition: Item High temp. Storage High temp. Operating Low temp. Storage Low temp. Operating
www..com
Condition 80C 70C -30C -20C 40C/ 90%RH 0C 25C 50C (30 min 5 min 30min)
Time (hrs) 48 48 48 48 48 10cycles
Assessment
No abnormalities in functions and appearance
Humidity
Temp. Cycle
Recovery time should be 24 hours minimum. Moreover, functions, performance and appearance shall be free from remarkable deterioration within 50,000 hours under ordinary operating and storage conditions room temperature (20+8C), normal humidity (below 65% RH), and in the area not exposed to direct sun light.
15
12.4 Precaution for using LCD/lCM
LCD/LCM is assembled and adjusted with a high degree of precision. Do not attempt to make any alteration or modification. The followings should be noted. General Precautions: 1. LCD panel is made of glass. Avoid excessive mechanical shock or applying strong pressure onto the surface of display area. 2. The polarizer used on the display surface is easily scratched and damaged. Extreme care should be taken when handling. To clean dust or dirt off the display surface, wipe gently with cotton, or other soft material soaked with isoproply alcohol, ethyl alcohol or trichlorotriflorothane, do not www..com use water, ketone or aromatics and never scrub hard. 3. Do not tamper in any way with the tabs on the metal frame. 4. Do not made any modification on the PCB without consulting AV. 5. When mounting a LCM, make sure that the PCB is not under any stress such as bending or twisting. Elastomer contacts are very delicate and missing pixels could result from slight dislocation of any of the elements. 6. Avoid pressing on the metal bezel, otherwise the elastomer connector could be deformed and lose contact, resulting in missing pixels and also cause rainbow on the display. 7. Be careful not to touch or swallow liquid crystal that might leak from a damaged cell. Any liquid crystal adheres to skin or clothes, wash it off immediately with soap and water.
Static Electricity Precautions: 1. CMOS-LSI is used for the module circuit; therefore operators should be grounded whenever he/she comes into contact with the module. 2. Do not touch any of the conductive parts such as the LSI pads; the copper leads on the PCB and the interface terminals with any parts of the human body. 3. Do not touch the connection terminals of the display with bare hand; it will cause disconnection or defective insulation of terminals. 4. The modules should be kept in anti-static bags or other containers resistant to static for storage. 5. Only properly grounded soldering irons should be used. 6. If an electric screwdriver is used, it should be grounded and shielded to prevent sparks. 7. The normal static prevention measures should be observed for work clothes and working benches. 8. Since dry air is inductive to static, a relative humidity of 50-60% is recommended.
16
Soldering Precautions: 1. 2. 3. 4. 5. 6. 7. Soldering should be performed only on the I/O terminals. Use soldering irons with proper grounding and no leakage. Soldering temperature: 280C+10C Soldering time: 3 to 4 second. Use eutectic solder with resin flux filling. If flux is used, the LCD surface should be protected to avoid spattering flux. Flux residue should be removed.
Operation Precautions:
www..com 1. The viewing
angle can be adjusted by varying the LCD driving voltage Vo. 2. Since applied DC voltage causes electro-chemical reactions, which deteriorate the display, the applied pulse waveform should be a symmetric waveform such that no DC component remains. Be sure to use the specified operating voltage. 3. Driving voltage should be kept within specified range; excess voltage will shorten display life. 4. Response time increases with decrease in temperature. 5. Display color may be affected at temperatures above its operational range. 6. Keep the temperature within the specified range usage and storage. Excessive temperature and humidity could cause polarization degradation, polarizer peel-off or generate bubbles. 7. For long-term storage over 40C is required, the relative humidity should be kept below 60%, and avoid direct sunlight.
Limited Warranty AV LCDs and modules are not consumer products, but may be incorporated by AV's customers into consumer products or components thereof, AV does not warrant that its LCDs and components are fit for any such particular purpose. 1. The liability of AV is limited to repair or replacement on the terms set forth below. AV will not be responsible for any subsequent or consequential events or injury or damage to any personnel or user including third party personnel and/or user. Unless otherwise agreed in writing between AV and the customer, AV will only replace or repair any of its LCD which is found defective electrically or visually when inspected in accordance with AV general LCD inspection standard . (Copies available on request) 2. No warranty can be granted if any of the precautions state in handling liquid crystal display above has been disregarded. Broken glass, scratches on polarizer mechanical damages as well as defects that are caused accelerated environment tests are excluded from warranty. 3. In returning the LCD/LCM, they must be properly packaged; there should be detailed description of the failures or defect.
17

▲Up To Search▲

Price & Availability of HY-1602H-803

	To Download HY-1602H-803 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .