 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Prepared Checked Approved Product Specifications Ref No. Total Page A- 1 12 1 AN7586 Structure Appearance Application Function Silicon Monolithic Bipolar IC SIL-7 Pins Plastic Package (Power Type With Fin) Low Frequency Amplifier Page No. Mono 10W Audio Power Amplifier, with standby circuit and incorporating protection circuits A No. 1 2 3 4 5 6 7 8 Item Storage Temperature Absolute Maximum Ratings Symbol Tstg Topr Popr Gopr Sopr Vcc Icc PD Ratings -55 ~ +150 -25 ~ +75 1.013x10 0.61x10 (1.0 0.6) 5 5 Unit C C Pa (atm) Note 1 1 2 2 Operating Ambient Temperature Operating Ambient Pressure Operating Constant Acceleration Operating Shock Power Supply V oltage Power Supply Current Power Dissipation 9,810 (1,000) 4,900 (500) m/s (G) m/s (G) 35.0 2.0 18.7 V A W 2 Operating Supply V oltage Range Vcc 10.0 V ~ 32.0 V Note : 1) Except these items, all other measurements are taken at Ta = 25 C. 2) Ta = 75 C with infinite heat sink. Eff. Date 11-Feb-1999 Eff. Date Eff. Date Eff. Date Matsushita Electronics Corporation FMSC-PSDA-002-01 Prepared Checked Approved Product Specifications Ref No. Total Page A -2 12 2 AN7586 Absolute Maximum Ratings Item Pin Voltage (Pin 3) Page No. A No. 1 Symbol V3 Ratings -0.3 ~ +3.0 Unit V Note Note) For the above mentioned terminals do not apply a voltage or current that is outside the described range. Eff. Date 11-Feb-1999 Eff. Date Eff. Date Eff. Date Matsushita Electronics Corporation FMSC-PSDA-002-01 Prepared Checked Approved Product Specifications Ref No. Total Page B-1 12 3 AN7586 Page No. B No. 1 2 3 4 5 6 7 8 Item Electrical Characteristics (Ambient temperature is 25C2C unless otherwise specified) Symbol Test Cct. Icq Vno Gv THD Po RR Vstb-on Vstb-off Condition Vin=0mV No input, Rg=10k Limit Unit Note Min Typ Max - Quiescent Current Output End Noise Voltage V oltage Gain Total Harmonic Distortion Maximum Output Power 30 0.22 34 0.2 10.0 55 - 60 0.4 36 0.4 - mA mV dB % W dB 2 2 Vin=57mV 32 - Vin=57mV Vcc=26V , THD=10% Vr=1 Vrms, fr=120Hz,Rg=10k No input Icc 0.1mA No input Icc 9.5mA 8.0 45 - Ripple Rejection Ratio Stand-by On Voltage Stand-by Off Voltage - 5.0 - V V 8.5 Note : 1) f=1kHz, RL=8, Vcc=26V, unless otherwise stated 2) For this measurement, use the 20Hz~20kHz (12dB/OCT) filter. Eff. Date 11-Feb-1999 Eff. Date Eff. Date Eff. Date Matsushita Electronics Corporation FMSC-PSDA-002-01 Prepared Checked Approved Product Specifications Ref No. Total Page C-1 12 4 AN7586 Page No. Description of Test Circuits and Test Methods Test Circuit : AN7586 1 + 2 3 + 1000 Rg 10k RL 8 (20W) 4 5 6 + 7 1000 100 STB 1 2 Vcc + 1 Vin V out Vcc Note: For ' OPERATIONAL MODE ', connect STB to Vcc. Eff. Date 11-Feb-1999 Eff. Date Eff. Date Eff. Date Matsushita Electronics Corporation FMSC-PSDA-002-01 Prepared Checked Approved Product Specifications Ref No. Total Page D-1 12 5 AN7586 Page No. Circuit Function Block Diagram + - Protection Circuit -Temperature -Over-voltage -Over-current -Load short Ripple Filter RF 1 GND (Input) 2 In 3 Out 4 GND (Output) 5 VCC Stand-by 6 7 Pin Descriptions Pin No. 1 2 3 4 Pin Descriptions Ripple Filter GND (input) Input Output Pin No. 5 6 7 Pin Descriptions GND (output) Vcc Standby Eff. Date 11-Feb-1999 Eff. Date Eff. Date Eff. Date Matsushita Electronics Corporation FMSC-PSDA-002-01 Prepared Checked Approved Product Specifications Ref No. Total Page Page No. E-1 12 6 AN7586 Package Name FP - 7S Unit : mm 3.6 6.4 0.25 7.7 0.3 7.8 0.25 7 5 17.2 0.3 15.3 0.3 7.6 0.25 0.60.1 6 R1.8 4 3 2 1 1.2 0.1 +0.1 0.25 -0.05 2.54 0.6 3.5 0.3 Company insignia Date Code Name of item Polarity Eff. Date 11-Feb-1999 FMSC-PSDA-002-01 Eff. Date Eff. Date Eff. Date Matsushita Electronics Corporation 16.90.3 Prepared Checked Approved Product Specifications Ref No. Total Page Page No. F 12 7 AN7586 SiN, Fe group, Ag plating, Solder plating, Ag paste, PSG, Cu group, Au plating, Solder dip, (Structure Description) Chip surface passivation Lead frame material Inner lead surface process Outer lead surface process Chip mounting method Wire bonding method Wire material Mold material Molding method Heat Fin Material Others ( Others ( Others ( Others ( ) ) ) ) ) ) ) ) ) ) 1 2, 6 2 6 3 4 4 5 5 7 Au-Si alloy, Solder, Others ( Others ( 38 m Others ( Others ( Multiplunger mold, Cu group, Others ( Others ( Thermalsonic bonding, Au, Epoxy, Transfer mold, Fe group, Diameter Package FP-7S 1 4 3 5 6 7 2 Eff. Date 11-Feb-1999 FMSC-PSDA-002-01 Eff. Date Eff. Date Eff. Date Matsushita Electronics Corporation Prepared Checked Approved Product Specifications Ref No. Total Page G-1 12 8 AN7586 Page No. Application Circuit VCC 100 R.F. VCC 1000 1 Operational Mode 6 Ripple Filter Standby Mode STB 7 1 Vin 10k 3 4 1000 SP 8 Protection Cct -Temperature -Over-Voltage -Over-Current -Load Short 5 Output GND 2 Input GND Operational Mode Standby Mode VCC 0V Eff. Date 11-Feb-1999 Eff. Date Eff. Date Eff. Date Matsushita Electronics Corporation FMSC-PSDA-002-01 Prepared Checked Approved Product Specifications (Technical Data) Ref No. Total Page Page No. G-2 12 9 AN7586 Pin No. 1 Function Ripple Filter 6 Adjacent Circuitry Pins Description / Signal This is the pin to connect the positive terminal of a ripple filter capacitor. DC Bias (V) Vcc-1.5VBE 30k 1 20k 15k 2 15.7k 2 Input GND Input ground pin. 0V 3 Input 3 This is the amplifier input pin. 200 400 30k 2 0V Eff. Date 11-Feb-1999 Eff. Date Eff. Date Eff. Date Matsushita Electronics Corporation FMSC-PSDA-002-01 Prepared Checked Approved Product Specifications (Technical Data) Ref No. Total Page Page No. G-2 12 10 AN7586 Adjacent Circuitry Pin Function No. 4 Output Pins Description / Signal DC Bias (V) 6 Output pin Pre Amp Driver Cct 4 Vcc/2 + _ 600 5 30k Vcc/2 5 Output Gnd Output ground. 0V 6 Vcc This is the power supply pin. Typ: 26V 7 Standby 6 Standby control pin. Standby Mode =0V Operational Mode = Vcc 7 5k 5k 3k 4 2 Eff. Date 11-Feb-1999 Eff. Date Eff. Date Eff. Date Matsushita Electronics Corporation FMSC-PSDA-002-01 Prepared Checked Approved Product Specifications Ref No. Total Page G-3 12 11 AN7586 FP-7S Page No. Power Dissipation vs. Ambient Temperature 1 Infinity Heat Sink 2 No Heat Sink : : Rth(j-c) = 4 C/W Rth(j-a) = 53.2 C/W 32 30 28 26 24 Power Dissipation PD (W) 22 20 18 16 14 12 10 8 6 4 2 0 0 31.25W 1 2.35W 2 40 60 80 100 120 140 20 Ambient Temperature Ta (C) Eff. Date 11-Feb-1999 FMSC-PSDA-002-01 Eff. Date Eff. Date Eff. Date Matsushita Electronics Corporation Prepared Checked Approved Product Specifications Ref No. Total Page Page No. H 12 12 AN7586 Application's Precautions (1) External heatsink is needed when used. External heatsink should be fixed to the chassis. Fin of the IC can be connected to GND. Please prevent "Output to VCC short", "Output to GND short", "Pin Shift" in direction of Pin 7 and "Reverse Insertion" to avoid damaging the IC. The temperature protection circuit will operate at Tj around 150C. However, if temperature decrease, the protection circuit will automatically be deactivated and resume normal operation. (2) (3) (4) Eff. Date 11-Feb-1999 FMSC-PSDA-002-01 Eff. Date Eff. Date Eff. Date Matsushita Electronics Corporation |
Price & Availability of AN7586
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |