|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
KOA SPEER ELECTRONICS, INC. SS-193 R7 AHA 6/29/06 Chip Inductors Type KQ 0805 1. Scope of Application CERTIFIED CERTIFIED This specification shall be applied to chip inductors KQ series produced by KOA Corporation. 2. Dimensions and Construction L W1 Flat Top Film t h d Magnetic Inner Wire Coating W2 Ceramic/ Ferrite Core Electrode Size Code L W1 Dimensions inches (mm) W2 t h d .016.006 KQ0805 .079.008 .059.008 .053.004 .051.008 (0.400.15) .018.004 (2.00.2) (1.50.2) (1.350.1) (1.30.2) (0.450.1) 3. Type Designation Type designation shall be as the following form. New Type KQ Type 0805 Size T Termination Material T: Sn (Other termination styles available, contact factory for options) TE Packaging TE: 7" Embossed Plastic TD: 7" Paper Tape 10N Nominal Inductance 10N: 10nH R10: 0.1H 1R0: 1.0H J Tolerance G: 2% J: 5% K: 10% M: 20% 0805 PAGE 1 OF 7 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-193 R7 4. Standard Applications Part Designation KQ0805TTE3N3* KQ0805TTE6N8* KQ0805TTE8N2* KQ0805TTE12N* KQ0805TTE15N* KQ0805TTE18N* KQ0805TTE22N* KQ0805TTE27N* KQ0805TTE33N* KQ0805TTE39N* KQ0805TTE47N* KQ0805TTE56N* KQ0805TTE68N* KQ0805TTE82N* KQ0805TTER10* KQ0805TTER12* KQ0805TTER15* KQ0805TTER18* KQ0805TTER22* KQ0805TTER27* KQ0805TTER33* KQ0805TTER39* KQ0805TTER47* KQ0805TTER56* KQ0805TTER68* KQ0805TTER82* Marking 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 Nominal Inductance (nH) 3.3 6.8 8.2 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 L Measuring Frequency Inductance Tolerance J: 5% K: 10% M:20% 50 250 G: 2% J: 5% K: 10% M:20% 55 500 60 200 Q Quality Factor Minimum Q Self Resonant DC Allowable Measuring Frequency Resistance DC Current Frequency Minimum Maximum Maximum (MHz) (MHz) () (mA) 1500 1000 6000 5500 4700 4000 3400 3300 2600 2500 2050 2000 1650 1550 1450 1300 1200 1100 920 870 850 650 600 560 375 340 188 215 0.08 0.11 0.12 0.15 0.17 0.20 0.22 0.25 0.27 0.29 0.31 0.34 0.38 0.42 0.46 0.51 0.56 0.64 0.70 1.0 1.4 1.5 1.76 1.9 2.2 2.35 600 500 150 G: 2% J: 5% K: 10% 100 65 400 50 250 48 50 25 J: 5% K: 10% 33 23 100 50 350 310 290 250 230 190 180 * Add tolerance character (G, J, K, M) 5. Rating No. 1 2 Item Storage temperature range Operating temperature range Specification -40C ~ +100C -40C ~ +125C 5.1 Measurement Method Nominal Inductance Range 3.3 nH to 820 nH Measuring Frequency Listed Table-1 PAGE 2 OF 7 Bolivar Drive I Test Equipment 4291A RF Impedance analyzer (H.P) Fixture 16193A Test fixture Setup E.L = 1.4 cm OSC = 500 mV P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-193 R7 6. Test Conditions Unless otherwise specified, the test shall be performed at the temperature of 2015C and at a relative humidity of 6520%. Reverse for the test conditions shall be performed at the temperature of 202C and at a relative humidity of 655%. 7. Reliability Tests 7-1 Electrical Characteristics Item Dielectric withstanding voltage Insulation resistance Flammability Requirement No evidence of flaming, fuming, or breakdown 1000M and over IEC 695-2-2 Test Methods 5 seconds at AC 500 V applied between both terminals and film. 1 minute at DC 100 V measured between both terminals and film. Withstands needle-flame test. 7-2 Mechanical Characteristics Item Terminal pull strength Terminal bending strength Requirement No evidence of damage No evidence of breakdown Test Methods Terminals shall withstand a pull of 10 N in a horizontal direction. Specimen shall be soldered on bend test board and force applied to the opposite side to cause a 10 mm deflection 2 hours in each direction of X, Y, Z, on PCB at a frequency range of 10-55-10Hz with 1.5 mm amplitude Dropping 1 m on the ground of concrete 1 time Immerse in the solder at 2605C for 101 seconds Immerse in the solder at 2305C for 30.5 seconds Accordance with MIL-STD-202F Method 215 PAGE 3 OF 7 Bolivar Drive I Vibration L/L within 5% Q/Q within 10% No evidence of damage L/L within 5% Q/Q within 10% No evidence of outer damage L/L within 5% Q/Q within 10% 95% of the terminal should be covered with new solder No damage and marking must remain legible Dropping Resistance to soldering heat Solderability Resistance to solvent P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-193 R7 7-3 Environmental Characteristics Item Low temperature storage High temperature storage Moisture endurance Requirement No evidence of damage L/L within 5% Q/Q within 10% No evidence of damage L/L within 5% Q/Q within 10% No evidence of damage L/L within 5% Q/Q within 10% No evidence of damage L/L within 5% Q/Q within 10% No evidence of damage L/L within 5% Q/Q within 10% No evidence of damage L/L within 5% Q/Q within 10% L/L within 5% Test Methods Store at -402C, for 1000 hours Store at +1252C, for 1000 hours Store at 402C, 90~95% RH for 1000 hours Biased to full rated current at +125C for 1000 hours Biased to 10% rated current at +85C, 85% RH for 1000 hours 100 cycles between -40C/hour and +125C/hour L/L to be measured at the temperature of between -40C and +125C as based on the inductance at 20C Load life High temperature High Humidity Thermal shock Temperature characteristics Unless otherwise specified, measurements shall be performed within 2 hours after leaving test samples for more than one hour at the normal temperature and at the normal humidity. PAGE 4 OF 7 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-193 R7 8. Packaging 8-1 Taping The tapes for taping shall be embossed carrier tapes of 8 mm width and 4 mm pitches. The standard quantity per reel shall be 2,000 pieces. (1) Dimensions of Carrier Tape Feeding hole* T2 oD0 A E F W Chip pocket T1 Chip inductor oD1 B P1 P2 P0 Tape running direction * 20 Pitches accumulation of feeding holes shall be 80 0.15 mm. Top tape peeling strength: 0.1N ~ 0.7N Dimensions in inches (mm) Series A B W E F T1 0.062 0.003 0.087 0.003 0.059 0.003 3N3~R39 (1.60 0.1) (2.22 0.1) 0.314 0.007 0.068 0.003 0.137 0.001 (1.5 0.1) (1.75 0.1) (3.5 0.05) 0.057 0.003 0.066 0.003 0.086 0.003 (8.0 0.2) R47~R82 (1.7 0.1) (2.20 0.1) (1.45 0.1) Dimensions in inches (mm) Series 3N3~R39 R47~R82 T2 P0 P1 P2 oD0 oD1 0.009 0.001 0.157 0.003 0.157 0.003 0.078 0.001 0.059 . 0.003 .. 0.039 . 0.007 .. ... ... 0 0 0.2 0.1 (0.25 0.05) (4.0 0.1) (4.0 0.1) (2.0 0.05) (1.5 0 ) (1.0 0 ) PAGE 5 OF 7 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-193 R7 (2) Taped Configurations (conforming to EIA-481 standard) Empty space Chip mounting space Empty space Leader space End 11.80 (160) min. Dimensions in inches (mm) 9.04 (230) min. Drawing out direction 10.62 (160) min. Beginning (3) Reel Dimensions and Indication .448 (11.4 1.0) .079 (2.0 0.5) .511 (13 0.2) 2.36 (60 1.0) .826 (21 0.8) Indicate position The following items shall be indicated on the reel. * Type (KQ 0805 TE) * Nominal inductance and tolerance * Quantity * Production lot number * Manufacturer's name or trade mark 7.08 (180 0 ) 3 Dimensions in inches (mm) .354 (9.0 0.3) PAGE 6 OF 7 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-193 R7 9. General Information (1) Storage Chip inductors shall not be stored under high temperature and high humidity conditions. Especially, do not store taping where they are exposed to heat or direct sunlight. Otherwise, the packing material may be deformed, causing problems during mounting. (2) Mounting Placement force should not be excessive. (3) Soldering Flow soldering should be done at 260C for less than 10 seconds. Reflow soldering should be done at 240C for less than 30 seconds. When using a soldering iron, temperature shall not exceed 350C and within 3 seconds. Soldering iron time of each electrode shall be allowed only one time. After soldering, chip inductors shall not be stressed excessively. (4) Cleaning There is no problem using organic solvents. Since this chip inductor is a coil of ultra-fine wire, it is susceptible to vibration. If an ultrasonic cleaning unit is used for cleaning, check for any possibility of problem generation before practical use since such cleaning units considerably differ in vibration level and mode. Although the conditions differ depending on the printed board size, ultrasonic cleaning is generally used in the conditions described below as examples. Power: Within 20 W/L Cleaning times: Within 5 minutes (5) Pattern design The land pattern is recommended as follows. .110 (2.80) Inductor position Solder resist .016 (0.40) .07 (1.78) .03 (0.76) Dimensions in inches (mm) PAGE 7 OF 7 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. |
Price & Availability of KQ0805TTER22 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |