 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 7 A H-Bridge for DC-Motor Applications TLE 6209 R Data Sheet 1 1.1 * * * * * * * * * * * * * * * * * * Overview Features Delivers up to 6 A continuous and 7 A peak current Optimized for DC motor management applications Very low RDS ON of typ. 150 m @ 25 C per switch Operates at supply voltages of up to 40V Overvoltage Protection against transients up to 45 V Outputs fully short circuit protected PG-DSO-20-37 Standard SPI-Interface, daisy chain capability Adjustable chopper current regulation of up to 7 A Temperature monitor with prewarning, warning and shutdown Over- and Undervoltage-Lockout Open load detection Detailed load failure diagnosis by SPI Minimized power dissipation due to active free-wheeling Low EMI due to voltage slope regulation Very low current consumption (typ. 20 A @ 25 C) in stand-by (Inhibit) mode Enhanced power PG-DSO-Package Green Product (RoHS compliant) AEC Qualified Package PG-DSO-20-37 Type TLE 6209 R Functional Description The TLE 6209 R is an integrated power H-Bridge with D-MOS output stages for driving bidirectional loads such as DC-Motors. The design is based on Infineons Smart Power Technology SPT which allows bipolar, CMOS and power D-MOS devices on the same monolithic circuit. Operation modes forward (cw), reverse (ccw) and brake are invoked by two control pins PWM and DIR. Protection and a reliable diagnosis of overcurrent, openload, short-circuit to ground, to the supply voltage or across the load are integrated. Detailed diagnostic Data Sheet, Rev.3.1 1 2007-08-01 TLE 6209 R information is given via the 8 bit SPI status word. An integrated chopper current limitation limits the current e.g. to reduce power dissipation during mechanical block of a DC motor. Several device parameters can be set by the SPI control word. A three-level temperature monitoring with prewarning, warning and shutdown is included for controlled operation under critical power loss conditions. The full protection and diagnosis capability make the device suitable especially for safety relevant applications, e.g. in automotive ECUs. 1.2 Pin Configuration (top view) TLE 6209R 1 GND OUT 1 OUT 1 VS SCLK SDI SDO CSN INH GND GND OUT 2 OUT 2 VS DRV VCC PWM DIR DIS GND 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 Metal slug, connected to GND Pin Definitions and Functions VS DRV SDI SCLK OUT PWM DIS Power Supply Voltage Input for Charge pump buffer capacitor Serial Data Input Serial Clock Input Power Output PWM Input Disable Input 2 VCC GND SDO CSN - DIR INH 5 V Logic Supply Ground Serial Data Output Chip-Select-Not Input - Direction Input Inhibit 2007-08-01 Data Sheet, Version 3.1 TLE 6209 R 1.2.1 1, 10, 11, 20 2,3 4,17 Pin Definitions and Functions GND OUT1 Ground; internally connected to cooling tab (heat slug); to reduce thermal resistance place cooling areas and thermal vias on PCB. Output 1; output of D-MOS half bridge 1; external connection between pin 2 and pin 3 is necessary. Power supply; needs a blocking capacitor as close as possible to GND; 47 F electrolytic in parallel to 220 nF ceramic is recommended; external connection between pin 4 and pin 17 is necessary. Serial clock input; clocks the shiftregister; SCLK has an internal active pull down and requires CMOS logic levels Serial data input; receives serial data from the control device; serial data transmitted to SDI is an 8 bit control word with the Least Significant Bit (LSB) being transferred first; the input has an active pull down and requires CMOS logic levels; SDI will accept data on the falling edge of SCLK-signal; see Table 1 for input data protocol. Serial-Data-Output; this tri-state output transfers diagnosis data to the control device; the output will remain tri-stated unless the device is selected by a low on Chip-Select-Not (CSN); SDO state changes on the rising edge of SCLK; see Table 4 for diagnosis protocol. Chip-Select-Not input; CSN is an active low input; serial communication is enabled by pulling the CSN terminal low; CSN input should only be transitioned when SCLK is low; CSN has an internal active pull up and requires CMOS logic levels. Inhibit input; has an internal pull down; device is switched in standby condition by pulling the INH terminal low. Disable input; has an internal pull up; the output stages are switched in tristate condition by pulling the DIS terminal high. Direction input; has an internal pull down; TTL/CMOS compatible input. PWM input; has an internal pull down; TTL/CMOS compatible input. Logic supply voltage; needs a blocking capacitor as close as possible to GND; 10 F electrolytic in parallel to 220 nF ceramic is recommended. Pin No. Symbol Function VS 5 6 SCLK SDI 7 SDO 8 CSN 9 12 13 14 15 INH DIS DIR PWM VCC Data Sheet, Version 3.1 3 2007-08-01 TLE 6209 R 1.2.1 16 18,19 Pin Definitions and Functions (cont'd) DRV OUT2 Drive; Input for external charge pump capacitor CDRV Output 2; output of D-MOS half bridge 2; external connection between pin 2 and pin 3 is necessary. Pin No. Symbol Function 1.3 Functional Block Diagram VCC 15 Bias DRV 16 Charge Pump VS 4,17 INH DIS CSN SDI SCLK SDO PWM DIR 9 12 8 6 5 7 14 13 Inhibit FaultDetect Driver 8 Bit Logic and Latch & GateControl 18,19 OUT 2 2,3 S P I OUT 1 Direct Input UV OV TSD 1,10,11,20 GND 1 Figure 1 Block Diagram Data Sheet, Version 3.1 4 2007-08-01 TLE 6209 R 2 2.1 Circuit Description Serial Peripheral Interface (SPI) The SPI is used for bidirectional communication with a control unit. The 8-bit programming word or control word (see Table 1) is read in via the SDI serial data input, and this is synchronized with the serial clock input SCLK. The status word appears synchronously at the SDO serial data output (see Table 4). The transmission cycle begins when the chip is selected with the chip-select-not (CSN) input (H to L). When the CSN input changes from L to H, the word which has been read into the shift register becomes the control word. The SDO output switches then to tristate status, thereby releasing the SDO bus circuit for other uses. The SPI allows to parallel multiple SPI devices by using multiple CSN lines. Due to the full duplex shift register, the TLE 6209 R can also be used in daisy-chain configuration. The settings made by the SPI control word become active at the end of the SPI transmission and remain valid until a different control word is transmitted or a power on reset occurs. At each SPI transmission, the diagnosis bits as currently valid in the error logic are transmitted. The behavior of the diagnosis bits is described in Section 2.5. Table 1 Bit 7 6 5 4 3 2 1 0 Status Register Reset: H = reset OVLO: H = on, L = off not used MSB of 2bit chopper-OFF-time LSB of 2bit chopper-OFF-time PWM Operation mode: H = Fast decay, L = Slow decay MSB of 2 bit chopper current limit LSB of 2 bit chopper current limit Input Data Protocol Data Sheet, Version 3.1 5 2007-08-01 TLE 6209 R Table 2 Bit 1 0 0 1 1 Programmable Chopper Current Limit IL_xx Bit 0 0 1 0 1 Current limit IL_00 IL_01 IL_10 IL_11 Note: For actual values, see page 16 Table 3 Bit 4 0 0 1 1 Programmable Chopper OFF-time tOFF_xx Bit 3 0 1 0 1 Chopper-OFF-time tOFF_00 tOFF_01 tOFF_10 tOFF_11 Note: For actual values, see page 16 Table 4 Bit 7 6 5 4 3 2 1 0 Diagnosis Data Protocol H = Error/L = no error Power supply fail not used, always H Short to VS or across the load Short to GND Open load MSB of Temperature Monitoring LSB of Temperature Monitoring Error-Flag Table 5 Bit 2 0 0 Temperature Monitoring Bit 1 0 1 Chip Temperature Below Prewarning Temperature Prewarning Data Sheet, Version 3.1 6 2007-08-01 TLE 6209 R Table 5 Bit 2 1 1 2.2 2.2.1 Temperature Monitoring Bit 1 0 1 Supply Logic Supply Voltage, Power-On-Reset Chip Temperature Temperature Warning Overtemperature Shutdown The logic is supplied with 5 V by the VCC pin, separated from the power stage supply VS. The advantage of this system is that information stored in the logic remains intact even in the event of failures in the supply voltage VS. The power supply failure information can be read out via the SPI. If VCC falls below typically 4.5 V, the logic is shut down, all internally stored data is deleted and the Output Stages are switched to tristate. The IC is restarted on rising VCC with a hysteresis of typically 80 mV After this restart at increasing VCC, or if the device is activated after having been set into inhibit mode (INH L to H), the IC is initialized by Power-On-Reset (POR). After POR, all SPI control bits are set to L. This setting remains valid until first SPI communication. Also the error bits are reset by POR. 2.2.2 Power Supply Voltage The power stages are connected to the supply voltage VS. This voltage is monitored by over voltage (OV) and under voltage (UV) comparators as described in Section 2.5.6. The power supply voltage needs a blocking capacitor to GND. 2.3 2.3.1 Direct Inputs Inhibit (sleep mode) The INH input can be used to cut off the complete IC. By pulling the INH input to low, the power stages are switched to tristate, and the current consumption is reduced to just a few A at both the VS and the VCC input. It also leads to the loss of any data stored. The TLE 6209 R is reinitialized with POR if INH is put to high again. The pin has an internal pull-down. 2.3.2 Disable The DIS input can be used to disable the output stages. By pulling the DIS input to high the power stages are switched to tristate, regardless of the signals at the DIR and PWM inputs. The DIS input can be used as an emergency disable without resetting the SPI data stored in the IC. It has an internal pull-up. Data Sheet, Version 3.1 7 2007-08-01 TLE 6209 R 2.3.3 Direction and PWM The power stages are controlled by the direct inputs DIR and PWM as given in Table 6 and further illustrated in Figure 2. The DIR input gives the direction of output current, while the PWM input controls whether the current is increased or reduced. The SPI control bit 2 sets the decay mode, i.e. determines what happens if PWM = L. In pulsewidth modulated applications, this control scheme allows to supply the PWM-signal always through the same port, using less controller resources. Table 6 DIR 0 0 1 1 0 0 1 1 Functional Truth Table PWM 1 0 1 0 1 0 1 0 1 (fast decay) MODE (Bit 2) 0 (slow decay) OUT1 H H L H H L L H OUT2 L H H H L H H L Comments Motor turns clockwise Freewheel with slow decay Motor turns counterclockwise Freewheel with slow decay Motor turns clockwise Fast decay Motor turns counterclockwise Fast decay Slow Decay PWM = H PWM = L M M Fast Decay PWM = H PWM = L M M Figure 2 DIR/PWM Control with Slow- and Fast Decay Data Sheet, Version 3.1 8 2007-08-01 TLE 6209 R 2.4 Power Stages The output stages consist of a DMOS H-bridge built by two highside switches and two lowside switches. Integrated circuits protect the outputs against overcurrent and overtemperature if there is a short-circuit to ground or to the supply voltage or across the load. Positive and negative voltage spikes, which occur when switching inductive loads, are limited by integrated freewheeling diodes. 2.4.1 Charge Pump To realize the fast switching times, the charge pump, which generates the voltage necessary to switch on the n-channel D-MOS high-side switches, must be highly efficient. It requires an external capacitor CDRV which is connected to VS and the charge pump buffer input, DRV. It should be placed as close to the pins as possible. 2.4.2 Chopper Current Limitation To limit the output current, a chopper current limitation is integrated as shown in Figure 3. The current is measured by sense cells integrated in the low-side switches. As soon the current limit IL is reached, the low-side switch is switched off for a fixed time tOFF. IL and tOFF can be set by the SPI control bits 0,1, 3 and 4. current limit IL IOUT off-time tOFF time Figure 3 2.4.3 Chopper current limitation Active Freewheeling When drivng inductive loads with PWM operation, the dissipated power can be significantly reduced by activating the transistor located parallel to the internal freewheeling diode. This is realized in the TLE 6209 R. When switching an output from L to H, the high-side switch is turned on after a certain dead-time to avoid cross currents flowing through the half bridge. Data Sheet, Version 3.1 9 2007-08-01 TLE 6209 R 2.5 2.5.1 Protection and Diagnosis Short of Output to Ground The high-side switches are protected against a short of the output to ground by an over current shutdown. If a high-side switch is turned on and the current rises above the highside shutdown threshold ISDH for longer than the shutdown delay time tdOC, all output transistors are turned off and bit 4 the SPI diagnosis word is set. During the delay time, the current is limited to ISC (typically 20 A). The output stages stay off and the error bit set until a status register reset (bit 7 of SPI control word) is received or a power-on reset is performed. 2.5.2 Short of Output to VS Due to the chopper current regulation, the low-side switches are protected against a short to the supply voltage. To detect the short, the first time the current limit is reached, the off-command for the low-side switch is blanked out for 10 s. If the current rises above the low-side shutdown threshold ISDL during this time, all output transistors are turned off and bit 5 in the SPI diagnosis word is set. The value of the shutdown threshold depends on the current limit that is set via the SPI. The shutdown threshold is 1 A higher than the current limit. The output stages stay off and the error bit set until a status register reset (bit 7 of SPI control word) is received or a power-on reset is performed. 2.5.3 Short Across the Load The short circuit protection circuits of the high- and low-side switches work independently of each other. In most cases, a short across the load will be detected as a short to VS because of the longer filter time in the high-side switches tdOC and the higher shutdown threshold ISDH. 2.5.4 Open Load If the current through the low side transistor is lower than the reference current IdOL in ON-state (PWM = H), a timer is started. After a filter time tdOC an open load failure will be recognized and the status bit 3 is set. If the current exceeds the reference current IdOL the open load timer is reset. If the H-bridge is switched to OFF-state (PWM = L) the timer is stopped but not reset. The timer continues if the H-bridge is switched to ON-state again. There is no reset of the open load timer if the direction is changed using the DIR input in open load condition. The open load error bit is latched and can be reset by the status register reset bit 7 of the SPI control word or a POR. 2.5.5 Temperature Monitoring Temperature sensors are integrated in the power stages. The temperature monitoring circuit compares the measured temperature to the prewarning, warning and shutdown Data Sheet, Version 3.1 10 2007-08-01 TLE 6209 R thresholds. As soon as a threshold is reached, the according status bits are set in the SPI diagnosis word (c.f. Table 5). If the overtemperature shutdown threshold is reached, the output stages are turned off. The temperature monitoring messages and the over temperature shutdown are latched and can be reset by the status register reset bit 7 of the SPI control word or a POR. 2.5.6 Power Supply Fail The power supply Voltage is monitored for over- and under voltage lockout: * Under Voltage Lockout If the supply voltage VS drops below the switch off voltage VUV OFF, all output transistors are switched off and the power supply fail bit (bit 7 of the SPI diagnosis word) is set. If VS rises again and reaches the switch on voltage VUV ON, the power stages are restarted. The error bit, however, is latched and has to be reset by the status register reset bit 7 of the SPI control word. * Over Voltage Lockout If the supply voltage VS rises above the switch off voltage VOV OFF, all output transistors are switched off and the power supply fail bit (bit 7 of the SPI diagnosis word) is set. If VS falls again and reaches the switch on voltage VOV ON, the power stages are restarted. The error bit, however, is latched and has to be reset by the status register reset bit 7 of the SPI control word. The OVLO is only active if control bit 6 is H. If the bit is low, the OVLO is deactivated. 2.5.7 Error Flag Bit 0 of the SPI diagnosis word is an OR of the status bits 1 to 7. It can be read out without full SPI communication as described in Figure 8. Data Sheet, Version 3.1 11 2007-08-01 TLE 6209 R 3 3.1 Parameter Characteristics Absolute Maximum Ratings Symbol Limit Values min. max. Unit Remarks Voltages Supply voltage Supply voltage Logic supply voltage Logic input voltages (SDI, SCLK, CSN, INH, DIS, PWM, DIR) Logic output voltage (SDO) Output voltage (OUT1, OUT2) Charge pump buffer voltage (DRV) Currents Output current (cont.) Output current (peak) VS VS VCC VI - 0.3 -1 - 0.3 - 0.3 40 45 5.5 5.5 V V V V - t < 0.5 s; IS > - 2 A 0 V < VS < 40 V 0 V < VS < 40 V 0 V < VCC < 5.5 V 0 V < VS < 40 V 0 V < VCC < 5.5 V 0 V < VS < 40 V 0 V < VS < 40 V VO VOUT VDRV - 0.3 5.5 V - - - 0.3 V VS + 1,5V VS - 0.3 V VS + 15 V IOUT IOUT - - - - A A internally limited, see page 16 and page 17. Temperatures Junction temperature Storage temperature Tj Tstg - 40 - 50 150 150 C C - - Note: Maximum ratings are absolute ratings; exceeding any one of these values may cause irreversible damage to the integrated circuit. Data Sheet, Version 3.1 12 2007-08-01 TLE 6209 R 3.2 Parameter Operating Range Symbol Limit Values min. max. V V/s V After VS rising above VUV ON - - Outputs in tristate Outputs in tristate - - - Unit Remarks Supply voltage Supply voltage slew rate Logic supply voltage Supply voltage increasing Supply voltage decreasing Logic input voltage (SDI, SCLK, CSN, INH) SPI clock frequency Junction temperature Thermal Resistances Junction pin Junction ambient VS dVS /dt VUV OFF 40 -10 4.75 - 0.3 - 0.3 - 0.3 - - 40 10 5.50 VCC VS VS VI fCLK Tj VUV ON V VUV OFF V VCC V 2 150 MHz C RthjC RthjA - - 1.5 50 K/W K/W measured to pin 1, 10, 11, 20 - Data Sheet, Version 3.1 13 2007-08-01 TLE 6209 R 3.3 Electrical Characteristics 8 V < VS < 40 V; 4.75 V < VCC < 5.25 V; INH = High; all outputs open; - 40 C < Tj < 150 C; unless otherwise specified Parameter Symbol Limit Values min. Current Consumption Quiescent current Quiescent current typ. max. Unit Test Conditions IS IS - - - 10 50 30 A A INH = Low; VS = 13.2 V INH = Low; VS = 13.2 V; Tj = 25 C INH = Low - - Logic-Supply current Logic-Supply current Supply current ICC ICC IS - - - - 2.0 2.8 20 4.0 5.0 A mA mA Over- and Under-Voltage Lockout UV-Switch-ON voltage UV-Switch-OFF voltage UV-ON/OFF-Hysteresis OV-Switch-OFF voltage OV-Switch-ON voltage OV-ON/OFF-Hysteresis VUV ON VUV OFF VUV HY VOV OFF VOV ON VOV HY - 4.4 0.2 34 28 - 5.4 4.9 0.5 37 32 5.0 5.7 5.2 - 40 36 - V V V V V V VS increasing VS decreasing VUV ON - VUV OFF VS increasing VS decreasing VOV OFF - VOV ON Data Sheet, Version 3.1 14 2007-08-01 TLE 6209 R 3.3 Electrical Characteristics (cont'd) 8 V < VS < 40 V; 4.75 V < VCC < 5.25 V; INH = High; all outputs open; - 40 C < Tj < 150 C; unless otherwise specified Parameter Symbol Limit Values min. Outputs OUT1-2 Static Drain-Source-On Resistance Source (High-Side) IOUT = - 3 A typ. max. Unit Test Conditions RDS ON H - 140 170 m 5.2 V < VS < 40 V Tj = 25 C; CDRV = 33 nF 5.2 V < VS < 40 V CDRV = 33 nF 5.2 V < VS < 40 V Tj = 25 C; CDRV = 33 nF 5.2 V < VS < 40 V CDRV = 33 nF - Sink (Low-Side) IOUT = 3 A 280 160 m m RDS ON L - 130 - 270 m Clamp Diodes Forward Voltage Upper Lower VFU VFL - - 1.0 1.0 1.5 1.5 V V IF = 3 A IF = 3 A Data Sheet, Version 3.1 15 2007-08-01 TLE 6209 R 3.3 Electrical Characteristics (cont'd) 8 V < VS < 40 V; 4.75 V < VCC < 5.25 V; INH = High; all outputs open; - 40 C < Tj < 150 C; unless otherwise specified Parameter Symbol Limit Values min. Open Circuit/Underload Detection Detection current Delay time Current Limits Current limit Current limit Current limit Current limit typ. max. Unit Test Conditions IOCD tdOC 30 2 - - 130 8 mA ms - - IL_00 IL_01 IL_10 IL_11 3.4 4.25 5.1 5.95 4 5 6 7 4.6 5.75 6.9 8.05 A A A A Bit 0 = L; Bit 1 = L; Bit 0 = H; Bit 1 = L; Bit 0 = L; Bit 1 = H; Bit 0 = H; Bit 1 = H; Low-Side Switch Overcurrent Shutdown Threshold ISDL 0.5 1.0 1.5 A ISDL = ISDL - IL Note: low-side shutdown threshold is guaranteed by design Switch-OFF Time during Current Limitation (Chopper OFF-Time) OFF-time OFF-time OFF-time OFF-time tOFF_00 tOFF_01 tOFF_10 tOFF_11 16 32 48 64 24 43 62 80 28 51 74 96 s s s s Bit 3 = L; Bit 4 = L; Bit 3 = H; Bit 4 = L; Bit 3 = L; Bit 4 = H; Bit 3 = H; Bit 4 = H; Data Sheet, Version 3.1 16 2007-08-01 TLE 6209 R 3.3 Electrical Characteristics (cont'd) 8 V < VS < 40 V; 4.75 V < VCC < 5.25 V; INH = High; all outputs open; - 40 C < Tj < 150 C; unless otherwise specified Parameter Symbol Limit Values min. High-Side Switch Overcurrent High-side shutdown threshold Shutdown delay time Short circuit current typ. max. Unit Test Conditions ISDH tdSD ISC 8 15 - 12 25 - 18 40 25 A s A - - during tdSD Note: For short circuit current definition, see Figure 5. Short circuit current is guaranteed by design Leakage Current / Output Current in Tristate Source-Output-Stage Sink-Output-Stage IQLH IQLL - 120 - 50 - 0.5 - 1 A mA VOUT = 0 V VOUT = VS Output Delay Times (device not in stand-by for t > 1 ms) High-side ON High-side OFF Low-side ON Low-side OFF td ON H td OFF H td ON L td OFF L - - - - 4 0.6 2 2.5 10 1 3.5 4 s s s s VS = 13.2 V, Resistive load of 12 Output Switching Times (device not in stand-by for t > 1 ms) High-side switch rise time High-side switch fall time Low-side switch rise time Low-side switch fall time tRISE H tFALL H tRISE L tFALL L - - 2 2 1.8 0.2 6.5 4.3 3.5 0.8 11 6.5 s s s s VS = 13.2 V, Resistive load of 12 Note: For switching time definitions, see Figure 6. Data Sheet, Version 3.1 17 2007-08-01 TLE 6209 R 3.3 Electrical Characteristics (cont'd) 8 V < VS < 40 V; 4.75 V < VCC < 5.25 V; INH = High; all outputs open; - 40 C < Tj < 150 C; unless otherwise specified Parameter Symbol Limit Values min. Inhibit Input typ. max. Unit Test Conditions VIINHH VIINHL L-input voltage threshold Hysteresis of input voltage VIINHHY Pull down current (low) IIINHL Pull down current (high) IIINHH H-input voltage threshold Disable Input - 0.2 50 10 - - - 300 25 - 0.7 - 500 50 80 VCC VCC mV A A - - - VIINH = 0.2 x VCC VIINH = 0.7 x VCC VIDISH VIDISL L-input voltage threshold Hysteresis of input voltage VIDISHY IIDISH Pull up current (high) Pull up current (low) IIDISL H-input voltage threshold Direction/PWM Input - 0.2 50 - 50 - 50 - - 300 - 25 - 0.7 - 500 - 10 - VCC VCC mV A A - - - VIDIS = 0.7 x VCC VIDIS = 0.2 x VCC VIH L-input voltage threshold VIL Hysteresis of input voltage VIHY Pull down current (low) II Pull down current (high) II H-input voltage threshold - 0.2 50 10 - - - 300 25 - 0.7 - 500 50 50 VCC VCC mV A A - - - VI= 0.2 x VCC VI= 0.7 x VCC Data Sheet, Version 3.1 18 2007-08-01 TLE 6209 R 3.3 Electrical Characteristics (cont'd) 8 V < VS < 40 V; 4.75 V < VCC < 5.25 V; INH = High; all outputs open; - 40 C < Tj < 150 C; unless otherwise specified Parameter Symbol Limit Values min. SPI-Interface Delay Time from Stand-by to Data In/Power on Reset Setup time typ. max. Unit Test Conditions tset - - 100 s - Logic Inputs SDI, SCLK and CSN VIH VIL L-input voltage threshold Hysteresis of input voltage VIHY Pull up current at pin CSN IICSNH H-input voltage threshold (high) Pull up current at pin CSN (low) - 0.2 50 - 50 - 50 10 - - - - 300 - 25 - 25 - 10 0.7 - 500 - 10 - 50 50 15 VCC VCC mV A A A A pF - - - VCSN = 0.7 x VCC VCSN = 0.2 x VCC VSDI (VSCLK) = 0.2 x VCC VSDI (VSCLK) = 0.7 x VCC 0 V < VCC < 5.25 V IICSNL Pull down current at pin SDI IISDIL and SCLK (low) (IISCLKL) Pull down current at pin SDI IISDIH and SCLK (high) (IISCLKH) Input capacitance at pin CSN, SDI or SCLK CI Note: Input capacitances are guaranteed by design. Data Sheet, Version 3.1 19 2007-08-01 TLE 6209 R 3.3 Electrical Characteristics (cont'd) 8 V < VS < 40 V; 4.75 V < VCC < 5.25 V; INH = High; all outputs open; - 40 C < Tj < 150 C; unless otherwise specified Parameter Symbol Limit Values min. Logic Output SDO H-output voltage level L-output voltage level Tri-state leakage current Tri-state input capacitance typ. max. Unit Test Conditions VSDOH VSDOL ISDOLK CSDO VCC -1.0 - - 10 - VCC -0.85 0.25 - 10 - 0.4 10 15 V V A pF ISDOH = 1 mA ISDOL = - 1.6 mA VCSN = VCC 0 V < VSDO < VCC VCSN = VCC 0 V < VCC < 5.25 V Note: Input capacitances are guaranteed by design. Data Sheet, Version 3.1 20 2007-08-01 TLE 6209 R 3.3 Electrical Characteristics (cont'd) 8 V < VS < 40 V; 4.75 V < VCC < 5.25 V; INH = High; all outputs open; - 40 C < Tj < 150 C; unless otherwise specified Parameter Symbol Limit Values min. Serial Data Input Timing Serial Clock period Serial Clock high time Serial Clock low time Serial Clock low before CSN low CSN setup time SCLK setup time Clock low after CSN high SDI setup time SDI hold time Input signal rise time at pin SDI, SCLK and CSN typ. max. Unit Test Conditions tPSCLK tSCLKH tSCLKL tbef tlead tlag tbeh tSDISU tSDIHO trSIN 500 250 250 250 250 250 250 125 125 - - - - - - - - - - - - - - - - - - - - - - 100 100 ns ns ns ns ns ns ns ns ns ns ns - - - - - - - - - - - Input signal fall time tfSIN at pin SDI, SCLK and CSN Serial Data Output Timing SDO rise time SDO fall time SDO enable time SDO disable time SDO valid time trSDO tfSDO tENSDO tDISSDO tVASDO - - - - - 25 25 - - 50 50 50 125 125 125 ns ns ns ns ns CL = 100 pF CL = 100 pF low impedance high impedance VDO < 0.2 VCC; VDO > 0.7 VCC; CL = 100 pF Data Sheet, Version 3.1 21 2007-08-01 TLE 6209 R 3.3 Electrical Characteristics (cont'd) 8 V < VS < 40 V; 4.75 V < VCC < 5.25 V; INH = High; all outputs open; - 40 C < Tj < 150 C; unless otherwise specified Parameter Symbol Limit Values min. typ. max. Unit Test Conditions Thermal Prewarning, Warning and Shutdown Thermal prewarning junction temperature Temperature prewarning hysteresis Thermal warning junction temperature Temperature prewarning hysteresis TjPW T 120 - 140 - 160 - 1.07 1.06 140 20 160 20 180 20 1.14 1.13 160 - 180 - 200 - - - C K C K C K - - - - - - - - - - TjW T Thermal shutdown junction TjSD temperature Temperature shutdown hysteresis Ratio of W to PW temperature Ratio of SD to W temperature T TjW / TjPW TjSD / TjW Note: Temperature thresholds are guaranteed by design. Data Sheet, Version 3.1 22 2007-08-01 TLE 6209 R 4 Diagrams V 13.2V 9V 9V VOUT 0 tOFF_xx IOUT Figure 4 Switch-OFF time during current limitation (chopper OFF-time) Vs V Vs 5V PWM 0 OUT tdSD IOUT ISDH GND ISC Figure 5 Short circuit of high-side switch to GND Data Sheet, Version 3.1 23 2007-08-01 TLE 6209 R V 5 PW M Input 0 50% 50% t R ISE 100% 90% t FALL 90% V O UT 10% 10% t d1 DIR = L / H => V O UT = V O UT 1/2 Resistive load to V s => t R ISE = t RISE L , t FALL = t FAL L L t d1 = t d O FF L , t d2 = t d O N L td2 Resistive load to G ND => t R IS E = t R ISE H, t FALL = t FALL H t d1 = t d O N H, t d2 = t d O FF H Figure 6 Output Delay and Switching Time Definitions CSN High to Low & rising edge of SCLK: SDO is enabled. Status information is transfered to Output Shift Register CSN time CSN Low to High: Data from Shift-Register is transfered to Output Driver Logic SCLK 0 1 2 3 4 5 6 7 0 actual Data SDI 0 1 2 3 4 5 6 7 new Data 0 + SDI: Data will be accepted on the falling edge of CLK-Signal previous Status SDO _ 0 1 _ _ 2 _ 3 _ 4 _ 5 _ 6 _ 7 actual Status 0 SDO: State will change on the rising edge of CLK-Signal old Data actual Data Figure 7 Standard Data Transfer Timing Data Sheet, Version 3.1 24 2007-08-01 TLE 6209 R CSN High to Low & SCLK stays Low: Status information of Data Bit 0 ( Error Flag ) is transfered to SDO CSN time SCLK SDI SDI: Data is not accepted SDO tristate _ 0 tristate SDO: Status information of Data Bit 0 ( Error-Flag ) will stay as long as CSN is low Figure 8 Timing for Error Detection Only 0.7 VCC CSN 0.2 VCC tSCLKH 0.7 VCC SCLK 0.2 VCC tlead tbef tSDISU tSDIHO 0.7 VCC tSCLKL tlag tbeh SDI Dont care Valid Dont care Valid Dont care 0.2 VCC Figure 9 SPI-Input Timing Data Sheet, Version 3.1 25 2007-08-01 TLE 6209 R trSIN tfSIN 0.7 VCC SCLK trSDO 50 % 0.2 VCC 0.7 VCC SDO ( low to high ) 0.2 VCC tVASDO tfSDO 0.7 VCC SDO ( high to low ) 0.2 VCC Figure 10 DO Valid Data Delay Time and Valid Time tfSIN trSIN 0.7 VCC CSN tENSDO tDISSDO 50 % 0.2 VCC SDO 10 k Pullup to VCC 50 % tENSDO tDISSDO 10 k Pulldown 50 % to GND SDO Figure 11 SDO Enable and Disable Time Data Sheet, Version 3.1 26 2007-08-01 TLE 6209 R 5 Application Watchdog Reset Q TLE 4278G D CD 10nF I Vbat Z39 GND 100F 100nF CQ 22F CDRV WD R VCC VCC 15 DRV 16 33nF VS 4,17 Bias Charge Pump INH MicroController for EMS/ETC Function DIS CSN SDI SCLK SDO 9 12 8 6 5 7 Inhibit FaultDetect 2,3 S P I 8 Bit Logic and Latch Driver & Gate-Control 18,19 OUT 1 OUT 2 M PWM DIR 14 13 Direct Input UV 1 GND OV Micro-Controller for Evaluation Process Monitoring TSD GND GND Figure 12 Application Circuit Data Sheet, Version 3.1 27 2007-08-01 TLE 6209 R 6 Package Outlines PG-DSO-20-37 (Plastic Dual Small Outline Package) 3.5 max. 1.3 0.25 +0.0 7 - 1.2 -0.3 0 +0.15 3.25 0.1 0.02 11 0.15 1) 2.8 B 15.74 0.1 1.27 0.4 +0.13 0.1 0.25 M 6.3 14.2 0.3 A 20x Heatsink 0.95 0.15 0.25 M 20 11 Index Marking 1 1 x 45 10 A 1) Does not include plastic or metal protrusion of 0.15 max. per side 15.9 0.15 1) GPS05791 Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). You can find all of our packages, sorts of packing and others in our Infineon Internet Page "Products": http://www.infineon.com/products. SMD = Surface Mounted Device Data Sheet, Version 3.1 28 Dimensions in mm 2007-08-01 5 3 B TLE 6209 R 7 Version Rev. 3.1 Revision History Date Changes 2007-08-01 RoHS-compliant version of the TLE 6209 R * All pages: Infineon logo updated * Page 1: "AEC qualified" and "RoHS" logo added, "Green Product (RoHS compliant)" and "AEC qualified" statement added to feature list, package names changed to RoHS compliant versions, package pictures updated, ordering codes removed * Page 28: Package name changed to RoHS compliant version, "Green Product" description added * Revision History added * Legal Disclaimer added Data Sheet, Version 3.1 29 2007-08-01 Edition 2007-08-01 Published by Infineon Technologies AG 81726 Munich, Germany (c) 8/1/07 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. |
Price & Availability of TLE6209R07
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |