View HMC807LP6CE_4802647.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HMC807LP6CE
v00.0609
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 12.4 - 13.4 GHz
Features
* 24 bit Step Size, Resolution 3 Hz typ * 225 MHz, 14-bit reference path input * Direct FSK Modulation Mode * Cycle Slip Prevention * Read / Write Serial Port, Chip ID * 40 Lead 6x6mm SMT Package: 36mm2
Features
* RF Bandwidth: 12.4 GHz to 13.4 GHz * Fractional or Integer Modes * Ultra Low Phase Noise 12.9 GHz; 50 MHz Ref. -95 / -98 dBc/Hz @ 10 kHz (Frac / Int) -132 dBc/Hz @ 1 MHz (Open Loop) * Figure of Merit (FOM) -221 / -226 dBc/Hz (Frac / Int)
Typical Applications
12
PLLS w/ INTEGRATED VCO - SMT
* VSAT Radio * Point-to-Point / Multi-Point Radio * Test Equipment & Industrial Control
* Military End-Use * Phased Array Applications
Functional Diagram
[1] Please refer to the pin description table for details
12 - 44
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC807LP6CE
v00.0609
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 12.4 - 13.4 GHz
General Description
The HMC807LP6CE is a fully functioned Fractional-N Phase-Locked-Loop (PLL) Frequency Synthesizer with an Integrated Voltage Controlled Oscillator (VCO). The input reference frequency range is 100 kHz to 220 MHz while the advanced delta-sigma modulator design in the fractional synthesizer allows both ultra-fine step sizes and very low spurious products. The highly integrated structure provides excellent phase noise performance over temperature, shock and process. The HMC807LP6CE is packaged in a leadless QFN 6x6 mm surface mount package. The output power is 8 dBm typical, making the HMC807LP6CE ideal for driving the LO port of many of Hittite's Hi Linearity and I/Q mixer products. For theory of operation and register map refer to the "PLLs w/ Integrated VCO - Microwave VCOs" Operating Guide. To view the Operating Guide, please visit www.hittite.com and choose HMC807LP6CE from the "Search by Part Number" pull down menu.
Electrical Specifi cations, TA = +25 C; VCCVCO, VDDCP, VCCCP = +5V; AVCC, VCCPS
VDDPFD, AVDD, RVDD, DVDD, DVDDM, DVDDQ, VDDIO = +3.3V; AGND = DGND = 0V
Parameter Condition Min. Typ. Max. Units
12
PLLS w/ INTEGRATED VCO - SMT
12 - 45
RF Output Characteristics
VCO Output Frequency Range VCO Output Power VCO Tuning Voltage VCO Tuning Sensitivity Frequency Pulling (into a 2:1 VSWR) Frequency Pushing Frequency Drift Rate Sub Harmonic (1/2) Harmonic (2nd) Harmonic (3rd) VCO SSB Phase Noise @ 100 kHz Offset (Open Loop) Synthesizer In-Band SSB Phase Noise @ 10 kHz Offset (Frac/Int) Synthesizer Normalized In-Band SSB Phase Noise Floor (Frac/Int) Synthesizer Fractional Spurs [1] Synthesizer Frequency Settling Time (100 MHz Step) 16-Bit Divider Range (Int) 16-Bit Divider Range (Frac) From 13 GHz to 12.9 GHz Loop BW = 100 kHz N Divider Ratio 216+31 N Divider Ratio 216 -1 32 36 V TUNE = +5V Fvco = 12.9 GHz Fref = 50 MHz Fvco = 12.9 GHz Loop BW = 100 kHz V TUNE = +5V V TUNE = +5V 12.4 4 2 190 5 6 1.2 25 18 35 -110 -95 / -98 -221 / -226 -65 104 65567 65535 12.9 8 13.4 10 13 GHz dBm V MHz/V MHz pp MHz/V MHz/ C dBc dBc dBc dBc/Hz dBc/Hz dBc/Hz dBc us
REF Input Characteristics
Max Ref Input Frequency (3.3V) Min Ref Input Frequency Ref Input Sensitivity Max Ref Input Ref Input Capacitance 14-Bit Ref Divider Range 16383 AC Coupled DC Coupled 0 200 225 100 500 200 700 VDDIO 5 1 MHz kHz mVpp V pF
[1] Actual spur level is dependent on loop parameters and will increase at division ratios closest to integer boundaries. Number listed is average value.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC807LP6CE
v00.0609
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 12.4 - 13.4 GHz
Electrical Specifi cations (Continued)
Parameter Condition Min. Typ. Max. Units
Phase Detector
Max Phase Detector Frequency (Frac) Max Phase Detector Frequency (Int) Min Phase Detector Frequency 70 140 105 160 100 MHz MHz kHz
Charge Pump
Max Output Current Min Output Current Charge Pump Noise Input referred 50 MHz Ref. 2 500 -145 mA A dBc/Hz
Logic Inputs
12
PLLS w/ INTEGRATED VCO - SMT
VIH Input High Voltage VIL Input Low Voltage
VDDIO-0.4 0
VDDIO 0.4
V V
Logic Outputs
VOH Output High Voltage VOL Output Low Voltage Serial Port Max Clock VDDIO-0.4 0 50 VDDIO 0.4 V V MHz
Power Supply Voltages
Analog 3.3V Supplies: AVCC, VDDPFD, AVDD, RVDD, VCCPS Digital Internal Supplies: DVDD, DVDDQ, DVDDM Digital I/O Supplies: VDDIO Analog 5V Supplies: VCCVCO, VDDCP, VCCCP Logic I/O VCCCP must equal VDDCP AVDD must equal DVDD 3 3 1.8 4.75 3.3 3.3 3.3 5 3.45 3.45 5.5 5.25 V V V V
Power Supply Currents
Total Current Consumption (5V) Total Current Consumption (3.3V) Power Down Current [1] CSP Disabled CSP Enabled Measured with 10 G meter 1.880 205 90 1 450 1.920 1.960 250 110 10 mA mA A A V
Bias Reference Voltage
[1] Refers only to the Synthesizer portion of the HMC807LP6CE
12 - 46
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC807LP6CE
v00.0609
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 12.4 - 13.4 GHz
SSB Phase Noise vs. Frequency, Integer Mode
-60 -70 PHASE NOISE (dBc/Hz) -80 -90 -100 -110 -120 -130 -140 -150 10
2
SSB Phase Noise vs. Temperature @ 12.9 GHz, Integer Mode
-60 -70 PHASE NOISE (dBc/Hz) -80 -90 -100 -110 -120 -130 -140 -150 2 10 Fref = 50MHz Loop BW = 100kHz
3 4 5 6 7
12.4 GHz 12.9 GHz 13.4 GHz
+25 C +85 C -40 C
Temp = 25C Fref = 50MHz Loop BW = 100kHz
3 4 5 6 7
10
10
10
10
10
10
10
10
10
10
OFFSET FREQUENCY (Hz)
OFFSET FREQUENCY (Hz)
12
PLLS w/ INTEGRATED VCO - SMT
12 - 47
SSB Phase Noise Fractional Spurs @ 12.902 GHz
-60 -70 PHASE NOISE (dBc/Hz)
SSB Phase Noise vs. Reference Freq. & Loop BW @ 12.9 GHz, Integer Mode
-60 -70 PHASE NOISE (dBc/Hz) -80 -90 -100 -110 -120 -130 -140 Fref = 10MHz Loop BW= 10kHz Fref = 50MHz Loop BW=100kHz
-80 -90 -100 -110 -120 -130 -140 -150 2 10 Temp = 25C Fref = 50MHz Loop BW = 100kHz
3 4 5 6 7
10
10
10
10
10
-150 2 10
10
3
10
4
10
5
10
6
10
7
OFFSET FREQUENCY (Hz)
OFFSET FREQUENCY (Hz)
Example of Cycle Slip Prevention Hop from 13.2 to 12.7 GHz
13.3 13.2 FREQUENCY (GHz)
Typical Reference Sensitivity vs. Frequency, 3.3V [1]
20 10 SENSITIVITY (dBm) 0 -10 -20 -30 -40 -50 R = 3, +25C R = 3, +85C R = Max, +25C R = Max, +85C
13.1 13 12.9 12.8 12.7 12.6 -10
CSP ON CSP OFF
0
10
20 30 TIME (SEC)
40
50
0
50
100
150
200
250
300
FREQUENCY (MHz)
[1] R refers to the reference path division ratio
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC807LP6CE
v00.0609
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 12.4 - 13.4 GHz
Frequency vs. Tuning Voltage, T= 25C
14 OUTPUT FREQUENCY (GHz) OUTPUT FREQUENCY (GHz) 13.6 13.2 12.8 12.4 12 11.6 11.2 10.8 0 1 2 3 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (VOLTS)
Vcc=4.75V Vcc=5.0V Vcc=5.25V
Frequency vs. Tuning Voltage, Vcc= +5V
14 13.6 13.2 12.8 12.4 12 11.6 11.2 10.8 0 1 2 3 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (VOLTS)
+25C +85C -40C
12
PLLS w/ INTEGRATED VCO - SMT
800 700 600 500 400 300 200 100 0 0 1 2 3 SENSITIVITY (MHz/Volt)
Sensitivity vs. Tuning Voltage, Vcc= +5V
Output Power vs. Tuning Voltage, Vcc= +5V
12 10 8 6 4 2 0
+25C +85C -40C
OUTPUT POWER (dBm)
+25C +85C -40C
4
5
6
7
8
9
10
11 12
13
0
1
2
3
4
5
6
7
8
9
10
11 12
13
TUNING VOLTAGE (VOLTS)
TUNING VOLTAGE (VOLTS)
Open Loop VCO SSB Phase Noise @ Vtune = +5V
0 SSB PHASE NOISE (dBc/Hz) -20 -40 -60 -80
+25C +85C -40C
Open Loop VCO SSB Phase Noise vs. Tuning Voltage
0 SSB PHASE NOISE (dBC/Hz) -20 -40 -60 -80
10 kHz Offset 100 kHz Offset
-100 -120 -140 -160 3 10
-100 -120
10
4
10
5
10
6
10
7
1
2
3
4
5
6
7
8
9
10
11
12
13
OFFSET FREQUENCY (Hz)
TUNING VOLTAGE (VOLTS)
12 - 48
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC807LP6CE
v00.0609
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 12.4 - 13.4 GHz
Pin Descriptions
Pin Number 1, 9 - 13, 22, 36 2 - 4, 7, 37, 39 5 8 40 6 14 Function N/C GND [1] GND VCCVCO2 [2] +5V Power Supply for VCO VCCVCO1 VTUNE ACG Control Voltage Input. Modulation port bandwidth dependent on drive source impedance. AC Ground. This pin must be connected to an external capacitor to ground. Analog Power supply pin for the RF Section. A decoupling capacitor to the ground plane should be placed as close as possible to this pin. Nominally 3.3V +5V Power Supply for charge pump digital section +5V Power Supply for the charge pump analog section Charge pump output Analog Power supply for the phase frequency detector, Nominally 3.3V External bypass decoupling for precision bias circuits, 1.920V 20 mV is generated internally Analog Power supply for analog ref paths, Nominally 3.3V Reference input (Negative or AC coupled to GND) Reference input (Positive) Ref path supply Digital supply for Substrate, Nominally 3.3V Chip Enable Serial port latch enable input Serial port clock input Serial port data input Power supply pin for internal digital circuitry. Nominally 3.3V Power Supply for digital I/O driver Lock Detect, Main Serial Data Output or VCO Serial Port Data Out Analog Power Supply for Prescaler, Nominally 3.3V Digital Power Supply for M-Counter, Nominally 3.3V RF output (AC coupled). Description No Connection. These pins may be connected to RF/DC ground. Performance will not be affected. These pins must be connected to RF/DC Ground These pins and package bottom must be connected to RF/DC Ground
15 16 17 18 19 20 21 23 24 25 26 27 28 29 30 31 32 33 34 35 38
AVCC VDDCP VCCCP CP VDDPFD BIAS [3] AVDD REFN REFP RVDD DVDDQ CE SEN SCK SDI DVDD VDDIO LD_SDO VCCPS DVDDM RFOUT
12
PLLS w/ INTEGRATED VCO - SMT
12 - 49
[1] This pin is not connected internally, however, this pin must be connected to GND to maintain product family pin for pin compatibility. [2] This pin is not connected internally, however, this pin must be connected to Vcc to maintain product family pin for pin compatibility. [3] BIAS ref voltage (pin 20) cannot drive an external load, and must be measured with a 10 GOhm meter such as Agilent 34410A; a typical 10 Mohm DVM will read erroneously.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC807LP6CE
v00.0609
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 12.4 - 13.4 GHz
Pin Schematic Equivalents
Pins Equivalent Schematic
RFOUT
VCCVCO1
12
VTUNE
PLLS w/ INTEGRATED VCO - SMT
GND
SEN, CE, SCK, SDI
LD_SDO
CP
12 - 50
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC807LP6CE
v00.0609
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 12.4 - 13.4 GHz
Pin Schematic Equivalents (Continued)
Pins Equivalent Schematic
Bias
12
PLLS w/ INTEGRATED VCO - SMT
12 - 51
REFN, REFP
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
12
2
JP1
1
2
40 39 38 37 36 35 34 33 32 31
5016 TP5
1
SYNTH
50 Ohm Trace
100NF C40
3 FOUT
VCCVCO1 GND RFOUT GND NC DVDDM VCCPS LD_SDO VDDIO DVDD
SDO
JP2
C32 4.7UF
2
C38 1NF
11 12 13 14 15 16 17 18 19 20
NC NC NC ACG AVCC VDDCP VCCCP CP VDDPFD BIAS
JP3
1
12 - 52
3VANALOG C12 100NF C10 10PF C8 10PF C9 100NF 3VDIGITAL
PLLS w/ INTEGRATED VCO - SMT
Evaluation Circuit
Header to USB Board
J1 3VDIGITAL
3 5 7 9 11 12 NC 10 NC 8 NC 6 NC 4 1 2
3VDIGITAL
R8 100K 3VDIGITAL
CEN
C14 100NF R1 100K TLW-106-05-T-D 3VDIGITAL C5 10PF 3VANALOG C2 10PF C3 100NF C7 100NF J3
1
C13 10PF
SCK SDI SDO SEN CEN
R20 1K
RFout
50 Ohm Co-Planar Trace 100PF
C15
3/5VVCO C4 4.7UF C1 1NF
LD
TP6
C29
v00.0609
REFin
1
J2
5016 C34 100NF R6
GND
TCXO
Y2
GND 2 VDD VC 4 1
1 2 3 4 5 6 7 8 9 10
30 NC SDI 29 GND SCK 28 GND SEN HMC807LP6CE 27 GND CE U1 26 GND DVDDQ 25 VTUNE HMC764/HMC807LP6CE RVDD 24 GND REFP 23 VCCVCO2 REFN 22 NC NC 21 NC AVDD
C21 1NF C35 100NF R2 120 R7 120 100NF 56
R9 C6 10PF C28 100NF 10 R24
DEPOP
3VTCXO
C31 100PF
R23 0 R28
DEPOP
C30
DEPOP
R10 0
C65 L1
DEPOP
DEPOP
R27
DEPOP
C61 3.9NF 3VANALOG C18 C16 10PF 100NF 3VANALOG C22 10PF C23 100NF
R21 30
DEPOP
R12 C62 R4 C33 1.2NF 620 C64 C37 39NF
DEPOP DEPOP
R3 1K C63
DEPOP
R13 200
+15V
7 2 6 DEPOP 3
TP4 R25
FB4
5VCP C24 10PF C25 100NF
5016 U5
4 DEPOP
TP3 THS4031IDGN R15 10K C60 1NF R14 10K JP6
1 2
C57 22UF R22 R26 0
1000
C58 4.7UF
C39 1NF
FB3
3VANALOG C26 10PF C27 100NF
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
5VCP
5016
1000
HMC807LP6CE
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 12.4 - 13.4 GHz
GND
Evaluation Circuit - Continued
5.5V
5016 TP1 FB1 1000 5016 R41 1K U9
/SD 6 ADJ BPASS VOUT GND 3 1 VIN 8 4
2
TP2
FB2 1000 C42 100NF C59 4.7UF
GND
JP5
1
R11 4.02K
5
R40 4.02K LP3878MR-ADJ C73 10NF
C67 1.2NF C41 100NF
C74 4.7UF
3/5VVCO C36 100NF C68 4.7UF
v00.0609
R17 1K U8
/SD 6 ADJ BPASS VOUT GND 3 1 VIN 8 4
R16 4.02K
5
C44 1.2NF LP3878MR-ADJ C47 10NF
C43 100NF
C48 4.7UF
5VCP C46 100NF C45 4.7UF
U2 LP5900-3_3V 3VANALOG
1 VOUT GND EN 3 4 VIN 6
C19 10PF
C20 100NF
R5 10K
C11 100NF
C17 4.7UF
U4 LP5900-3_3V
1 VOUT VIN 6 4 GND EN 3
3VDIGITAL C51 10PF C52 100NF
R18 10K
C50 100NF
C49 4.7UF
U6 LP5900-3_3V
1 VOUT VIN GND EN 3
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
3VTCXO C55 10PF C56 100NF
6 4
R19 10K
1
JP4
2
HMC807LP6CE
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 12.4 - 13.4 GHz
C54 100NF
C53 4.7UF
12
12 - 53
PLLS w/ INTEGRATED VCO - SMT
HMC807LP6CE
v00.0609
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 12.4 - 13.4 GHz
Absolute Maximum Ratings
Nominal 3.3V Supplies to GND Nominal Digital Supply to 3.3V Analog Supply Nominal 5V Supply to GND Vtune Storage Temperature Max Peak Reflow Temperature ESD Rating -0.3V to +3.6V -0.3V to +0.3V -0.3 to +5.5V 0 to +15V -65 to +150C 260 C Class 1A
Reliability Information
Junction Temperature to Maintain 1 Million Hour MTTF Nominal Junction Temperature (T=85 C) Thermal Resistance (Junction to GND Paddle, 5V Supply) Operating Temperature 135 C 120 C 34.2 C/W -40 to +85C
12
PLLS w/ INTEGRATED VCO - SMT
Outline Drawing
NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN.
Package Information
Part Number HMC807LP6CE Package Body Material RoHS-compliant Low Stress Injection Molded Plastic Lead Finish 100% matte Sn MSL Rating MSL3 Package Marking [1] H807 XXXX
[1] 4-Digit lot number XXXX
12 - 54
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC807LP6CE
v00.0609
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 12.4 - 13.4 GHz
Evaluation PCB
12
PLLS w/ INTEGRATED VCO - SMT
12 - 55
The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC807LP6CE
v00.0609
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 12.4 - 13.4 GHz
List of Materials for Evaluation PCB 127283 [1]
Item J1 J2, J3 JP1 - JP6 C1, C21, C38 - C39, C60 C2, C5, C6, C8, C10, C13, C16, C19, C22, C24, C26, C51, C55 C3, C7, C9, C11, C12, C14, C18, C20, C23, C25, C27 - C29, C34 - C36, C40 - C43, C46, C50, C52, C54, C56 C4, C17, C32, C45, C48, C49, C53, C68, C74 C15, C31 C33, C44, C67 C37 Description Dual Row Terminal Strip PCB Mount SMA RF Connector Single Row Terminal Strip 1000 pF Capacitor, 0402 Pkg. 10 pF Capacitor, 0402 Pkg.
0.1 F Capacitor, 0402 Pkg.
4.7 F Capacitor, 0805 Pkg. 100 pF Capacitor, 0402 Pkg. 1200 pF Capacitor, 0402 Pkg. 0.039 F Capacitor, 0603 Pkg. 10,000 pF Capacitor, 0402 Pkg. 22 F Tantalum Capacitor, Case D 4.7 F Tantalum Capacitor, Case B 3900 pF Capacitor, 0402 Pkg. 1000 Ohm 200 mA Ferrite Chip, 0805 Pkg. 100k Ohm Resistor, 0402 Pkg. 120 Ohm Resistor, 0402 Pkg. 1k Ohm Resistor, 0402 Pkg. 620 Ohm Resistor, 0402 Pkg. 10k Ohm Resistor, 0402 Pkg. 56 Ohm Resistor, 0402 Pkg. 10 Ohm Resistor, 0402 Pkg. Zero Ohm Resistor, 0402 Pkg. 4.02k Ohm Resistor, 0402 Pkg. 200 Ohm Resistor, 0402 Pkg. 30 Ohm Resistor, 0402 Pkg. Test Point PC Compact SMT HMC764LP6CE Fractional-N Synthesizer, with Integrated VCO Low Noise 3.3V, 100 mA Linear Regulator Low Noise Op-Amp, THS4031IDGN 5V, 800mA Voltage Regulator 3.3V, 50 MHz VCXO Crystal Oscillator 125536 Eval Board
12
PLLS w/ INTEGRATED VCO - SMT
C47, C73 C57 C58, C59 C61 FB1 - FB4 R1, R8 R2, R7 R3, R17, R20, R41 R4 R5, R14, R15, R18, R19 R6 R9 R10, R22, R23 R11, R16, R40 R13 R21 TP1 - TP6 U1 U2, U4, U6 U5 U8, U9 Y2 PCB [2]
[1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon 25FR and FR4
12 - 56
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC807LP6CE
v00.0609
FRACTIONAL-N SYNTHESIZER WITH INTEGRATED VCO, 12.4 - 13.4 GHz
Notes:
12
PLLS w/ INTEGRATED VCO - SMT
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
12 - 57

▲Up To Search▲

Price & Availability of HMC807LP6CE

	To Download HMC807LP6CE Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .