 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| JGC0118 Page 1 of 5 These lamps are of the so-called 1206 size, measuring approximately 1.5 x 3.0 mm. PART NO. JGC0118 Chip Material AlGaInP Emitted Color Green Lens Color Water Clear * Specifications subject to change without notice. Dimensions are in mm 0.1 unless stated otherwise. IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304 0902 JGC0118 Page 2 of 5 Absolute Maximum Ratings at Ta = 25 C Parameter Forward Current Reverse Voltage Operating Temperature Storage Temperature Electrostatic Discharge Power Dissipation Peak Forward Current (Duty 1/10 @ 1KHz) Soldering Temperature Symbol IF VR Topr Tstg ESD Pd IFP Tsol Rating 25 5 -40 to +85 -40 to +90 2000 60 60 Units mA V C C V mW mA Reflow Soldering: 260C for 10 sec. Hand Soldering: 350C for 3 sec. Electronic Optical Characteristics (Ta = 25 C) Parameter Luminous Intensity Viewing Angle Peak Wavelength Dominant Wavelength Spectrum Radiation Bandwidth Forward Voltage Reverse Current Symbol IV 21/2 p d VF IR Min. 29 -- -- -- -- 1.7 -- Typ. 39 60 575 573 20 2.0 -- Max. -- -- -- -- -- 2.4 10 Units mcd deg nm nm nm V A VR = 5 V IF = 20 mA Condition * Specifications subject to change without notice. Dimensions are in mm 0.1 unless stated otherwise. IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304 0902 JGC0118 Page 3 of 5 Typical Electro-Optical Characteristics Curves: * Specifications subject to change without notice. Dimensions are in mm 0.1 unless stated otherwise. IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304 0902 JGC0118 Page 4 of 5 Reel Dimensions: Carrier Tape Dimensions: * Specifications subject to change without notice. Dimensions are in mm 0.1 unless stated otherwise. IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304 0902 JGC0118 Page 5 of 5 Precautions for Use 1. Over-current prevention: A series resistor must be used for protection against over-current. Since slight voltage shifts can cause large current changes and possibly damage the LED. 2. Storage: 2.1. Store the LEDs in the sealed moisture proof bag until ready to use. 2.2. The storage conditions should be below 30C and 90% RH or less. 2.3. Unused portions of LEDs may be stored in moisture proof packages for up to 1 year if kept under 30C and at no more than 60% RH. 2.4. If there is evidence of moisture absorption or if the LEDs have been stored for a long time, bake the LEDs at 60C 5C for 24 hours prior to using. 3. Reflow Soldering Conditions: 3.1. Pb-free solder temperature profile (see figure): 3.2. Reflow solder no more than two times and must include time interval for the board to cool. 3.3. When soldering, do not put stress on the LEDs during heating. 3.4. After soldering, do not warp the circuit board. 4. Hand Soldering: Use a low wattage soldering iron (below 25 watts) with a tip temperature no more than 350C for 3 sec or less on one terminal. Wait at least two seconds before soldering the next terminal to avoid overheating the LED and damaging it. 5. Avoid reworking a soldered LED. It is best to simply replace it with a new part. * Specifications subject to change without notice. Dimensions are in mm 0.1 unless stated otherwise. IDEA, Inc., 1351 Titan Way, Brea, CA 92821 Ph: 714-525-3302, 800-LED-IDEA; Fax: 714-525-3304 0902 |
Price & Availability of JGC0118
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |