View SLH2815DKR_4686263.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Crane Aerospace & Electronics Power Solutions
sLH single and dual dc/dc converters
28 VoLt input - 1.5 Watt - pending reVision c reLease
Features
small size, 0.8 inches2 (5.16 cm2)
* Operating temperature -55 to +125C
* Qualified to MIL-PRF-38534 Class H and K * Input voltage range 16 to 40 VDC * Fully isolated, magnetic feedback * Inhibit function * Indefinite short circuit protection
* Radiation hardness assurance (RHA) to level R 100 kRad(Si)
* High power density, 88% efficiency
VDC Output SIngLES 5 12 15 DUALS 5 12 15
MODELS
description
With a miniature footprint of just 0.8 square inches, the SLH SeriesTM of 28 V DC/DC converters delivers 1.5 watts of output power while saving significant board area. The wide input voltage range of 16 to 40 VDC accepts the varying voltages of space, military, or aerospace bus power and tightly regulates output voltages to protect downstream components. Single output models feature outputs of 5, 12, or 15 volts, and dual output models feature outputs of 5, 12 and 15 volts.
When used with Interpoint's STF28-461 filter, the combination will meet the requirements of MIL-STD-461C, CE03.
inhibit Function
Screening
SLH converters offer the following screening options: Space Prototype (O), Class H, or Class K. Radiation tolerant to Radiation Hardness Assurance (RHA) levels of "-" (O) or "R", per MIL-STD-38534. Interpoint model numbers use an "O" in the RHA designator position to indicate the "-" (dash) Radiation Hardness Assurance level of MIL-PRF-38534, which is defined as "no RHA". See "Class H and K, QML Screening" tables for more information.
The SLH Series incorporates an inhibit terminal that can be used to disable internal switching. The converter is inhibited when an active low ( 0.5 V) signal is applied to the inhibit pin (pin 7). In the inhibit mode the inhibit pin sources up to 2 mA maximum. The converter resumes normal operation when an open circuit is applied to the inhibit pin. The open circuit voltage of the inhibit is 7 to 8 volts. Do not apply an external pull-up to the converter.
Protection FeatureS
All models include a soft-start function to prevent large current draw and minimize overshoot. The converters provide short circuit protection (by restricting the current) and output overload protection.
converter DeSign
convenient Packaging
SLH Series DC/DC converters incorporate a flyback topology with a variable switching frequency. Feedback provides output voltage regulation. Output voltage is magnetically fed back to the input side of the PWM to regulate output voltage. Up to 80% of the load of the dual output models may be on one output providing that the other output carries a minimum of 20% of the total load. The dual models can be used as a single output voltage by connecting the load between positive and negative outputs, leaving the common unconnected resulting in double the output voltage. (for example, SLH2805D can be used as a 10 VDC output.)
Crane Aerospace & Electronics Electronics group (Interpoint Brand) PO Box 97005 * Redmond WA 98073-9705 425.882.3100 * power@crane-eg.com www.interpoint.com
The SLH Series converters are packaged in hermetically sealed metal cases which provide EMI/RFI shielding.
Page 1 of 10 Rev C - 20090318 - Pending Revision C Release
Crane Aerospace & Electronics Power Solutions
sLH single and dual dc/dc converters
28 VoLt input - 1.5 Watt - pending reVision c reLease
Operating COnditiOns and CharaCteristiCs
input Voltage range * 16 to 40 VDC continuous * 50 V for 50 msec transient
inhibit
output power * 1.5 W
Lead soldering temperature (10 sec per lead) * 300C storage temperature range (case) * -65C to +150C
* Active low (output disabled) InH referenced to input common Active low 0.5 V max Inhibit pin current < 2mA * Active high (output enabled) Open collector or unconnected Pin voltage 7 to 8 volts, typical (open circuit) Do not apply external pull-up
capacitive Load * Single output models 100 F * Dual output models 100 F
input to output capacitance * 100 to 170 pF typical
output Voltage temperature coefficient * 100 ppm/C typical
case operating temperature (tc) * -55C to +125C full power * -55C to +135C absolute
isolation * 100 megohm minimum at 500 VDC * Any pin to case, except case pin
conversion Frequency (kHz), 28 Vin, full load * 25C, 280 typ * -55C to +125C; 220 min, 320 max
derating output power/current (tc) * Linearly from 100% at 125C to 0% at 135C
meChaniCal and envirOnmental
size (maximum) * 0.980 x 0.805 x 0.270 inches (24.89 x 20.45 x 6.86 mm) * See case A2 for dimensions. Weight (maximum) * 12 grams screening Space Prototype (O), Class H, or Class K Radiation tolerant to Radiation Hardness Assurance (RHA) levels of "-" (O) or "R", per MIL-STD-38534. Interpoint model numbers use an "O" in the RHA designator position to indicate the "-" (dash) Radiation Hardness Assurance level of MIL-PRF-38534, which is defined as "no RHA". See "Class H and K, QML Screening" tables, page 10. Available configurations: OO, HR, KR
www.interpoint.com
Rev C - 20090318 - Pending Revision C Release
Page 2 of 10
Crane Aerospace & Electronics Power Solutions
sLH single and dual dc/dc converters
28 VoLt input - 1.5 Watt - pending reVision c reLease
pin out
pin 1 2 3 4 5 6 7 single output Positive Input Input Common Positive Output Output Common Case ground no connection Inhibit dual output Positive Input Input Common Positive Output Output Common Case ground negative Output Inhibit
Squared corner and dot on top of cover indicate pin one.
12
3
4
Bottom View
7 6 5
See case A2 for dimensions.
Figure 1: pin Out
www.interpoint.com
Rev C - 20090318 - Pending Revision C Release
Page 3 of 10
Crane Aerospace & Electronics Power Solutions
sLH single and dual dc/dc converters
28 VoLt input - 1.5 Watt - pending reVision c reLease
ModeL nuMbering Key
Base Model Input Voltage SLH 28 12 D / K R
StanDarD MiCrOCirCuit Drawing (SMD) 5962R0052601KXC 5962R0052701KXC 5962R0052801KXC 5962R0250401KXC 5962R9955601KXC 5962R9852901KXC
sMd nuMbers
SLH SiMiLar part SLH2805S/KR SLH2812S/KR SLH2815S/KR SLH2805D/KR SLH2812D/KR SLH2815D/KR
Output Voltage Number of Outputs (S = single, D = dual)
Screening Radiation Hardness Assurance (RHA)
The SMD number shown is for Class K screening and Radiation Hardness Assurance (RHA) level R. See the SMD for the numbers for other screening and radiation levels. For exact specifications for an SMD product, refer to the SMD drawing. Call your Interpoint representative for status on the SMTR SMD releases which are "in process." SMDs can be downloaded from: http://www.dscc.dla.mil/programs/smcr
enter SLH28 BASE MODEL VOUT VALUE 5 12 15
ModeL seLection
One
SeLeCtiOn
FrOM eaCH CategOry
/ nUMBER OF OUTPUTS 1 s d CASE OPTIOn2 nO CASE OPTIOnS FOR SLH SCREEnIng 3 o H K RHA 4 o r
notes: 1. S is a single output and D is a dual output 2. There are not case options for the SLH. Only the standard case is available. 3. A screening level of O is a Space Prototype and is only used with RHA O. 4. Interpoint model numbers use an "O" in the RHA designator position to indicate the "-" (dash) Radiation Hardness Assurance level of MIL-PRF-38534, which is defined as "no RHA. RHA O is only available with Screening level O. For more information see page 10.
www.interpoint.com
Rev C - 20090318 - Pending Revision C Release
Page 4 of 10
Crane Aerospace & Electronics Power Solutions
sLH single and dual dc/dc converters
28 VoLt input - 1.5 Watt - pending reVision c reLease
Electrical Characteristics: -55 to + 125C Tc, 28 VDC Vin, 100% load, unless otherwise specified.
SIngLE OUTPUT MODELS paraMeter Output VOLtage 2 -55 Output Current Output pOwer Output rippLe COnDitiOnS 25C
tO
SLH2805S MIn 4.95 4.80 -- -- -- -- -- -- 16 -- -- -- -- 72 69 -- -- -- -- -- -- --
1
SLH2812S MAX 5.05 5.20 300 1.5 150 250 300 700 40 50 17 5 250 -- -- 1.5 30 400 400 600 500 20 500 100 MIn 11.88 11.52 -- -- -- -- -- -- 16 -- -- -- -- 80 69 -- -- -- -- -- -- -- -- -- TYP 12.00 -- -- -- 35 -- 60 380 28 -- 2.3 1.3 75 87 -- 0.3 -- 220 -- -- 1 -- -- MAX 12.12 12.48 125 1.5 200 300 400 700 40 50 17 5 300 -- -- 1.2 30 700 400 600 500 20 500 100 MIn 14.85 14.40 -- -- -- -- -- -- 16 -- -- -- -- 80 69 -- -- -- -- -- -- -- -- --
SLH2815S TYP 15.00 -- -- -- 60 -- 60 410 28 -- 2.4 1.3 60 88 -- 0.3 -- 220 -- -- -- 1 -- -- MAX 15.15 15.60 100 1.5 200 300 650 700 40 50 17 5 300 -- -- 1.2 30 700 400 600 500 20 500 100
TYP 5.00 -- -- -- 65 -- 115 440 28 -- 2.9 1.3 85 79 -- 0.4 -- 250 -- -- -- 1 -- --
unitS VDC mA W mV p-p mV mV VDC V mA mA p-p
+125 C
tO tO
Vin = 16 Vin = 16 25C, 10
40 VDC 40 VDC 2 MHz
kHz tO
-55 tO +125 C, 10 kHz tO 2 MHz Line reguLatiOn LOaD reguLatiOn input VOLtage Vin = 16
tO
40 VDC
tO
LOaD 10%
100%
nO LOaD tO FuLL COntinuOuS TRAnSIEnT 50 ms 1 nO LOaD inHiBiteD
input Current input rippLe Current 3 eFFiCienCy -55 LOaD FauLt 4, 5
10
kHz
- 10 MHz
25C, FuLL LOaD
tO
+125 C, FuLL LOaD
% W ms mV pk s mV pk s ms mV pk F
SHOrt CirCuit pOwer DiSSipatiOn reCOVery 1, 8 50% - 100% - 50% tranSient reCOVery tranSient reCOVery 1, 8 DeLay OVerSHOOt 25 C, nO eFFeCt On DC perFOrManCe
Step LOaD reSpOnSe 1,5 Step Line reSpOnSe 6 16 - 40 -16 VDC Start-up7 CapaCitiVe LOaD 1
-- --
notes: all temperatures refer to case temperature, tc. 1. guaranteed by design, not tested. 2. Specified at 50% load. 3. With a series inductor on the Vin power lead (Lin = 6 H). 4. Maximum duration of short circuit: 90 seconds at 25C, 30 seconds at 125C.
5. Load fault is a short circuit into 1 . Recovery is into resistive full load. 6. Transition > 10 s. 7. Measured from release of inhibit until Vout settles to within 1% of final value at full load with Vin at 28V. 8. Recovery = time to settle to within 1% of Vout final value.
www.interpoint.com
Rev C - 20090318 - Pending Revision C Release
Page 5 of 10
Crane Aerospace & Electronics Power Solutions
sLH single and dual dc/dc converters
28 VoLt input - 1.5 Watt - pending reVision c reLease
Electrical Characteristics: -55 to + 125C Tc, 28 VDC Vin, balanced 100% load, unless otherwise specified.
DUAL OUTPUT MODELS paraMeter Output VOLtage 2 -55 -55 Output Current
7
tO tO
SLH2805D MIn 4.95 -4.95 4.80 -4.80 -- -- -- -- -- -- -- -- -- 16 -- -- -- -- 72 69 -- -- -- -- -- -- -- -- -- TYP 5.00 -5.00 -- -- 150 -- -- 75 -- 75 65 310 300 28 -- 3.1 1.4 80 80 -- 0.3 -- 150 -- -- -- 1 -- -- MAX 5.05 -5.05 5.20 -5.20 240 300 1.5 150 250 400 400 700 700 40 50 17 5 250 -- -- 1.5 30 400 600 600 500 20 500 100 MIn 11.88 -11.88 11.52 -11.52 -- -- -- -- -- -- -- -- -- 16 -- -- -- -- 80 69 -- -- -- -- -- -- -- -- -- +VOut -VOut
SLH2812D TYP 12.00 -12.00 -- -- 62.5 -- -- 40 -- 75 70 350 350 28 -- 3.1 1.4 90 87 -- 0.3 -- 170 -- -- -- 2 -- -- MAX 12.12 -12.12 12.48 -12.48 100 125 1.5 200 400 700 700 700 700 40 50 17 5 300 -- -- 1.2 30 600 360 600 500 20 500 100 MIn 14.85 -14.85 14.40 -14.40 -- -- -- -- -- -- -- -- -- 16 -- -- -- -- 80 69 -- -- -- -- -- -- -- -- --
SLH2815D TYP 15.00 -15.00 -- -- 50 -- -- 65 -- 85 85 370 370 28 -- 3.3 1.4 100 87 -- 0.3 -- 200 -- -- -- 2 -- -- MAX 15.15 -15.15 15.60 -15.60 80 100 1.5 300 500 650 650 700 700 40 50 17 5 300 -- -- 1.2 30 700 600 600 500 20 500 100
COnDitiOnS 25C 25C
unitS
+125 C +VOut +125 C -VOut
VDC
EITHER OUTPUT Vin = 16 tO 40 VDC tOtaL, Vin = 16 VDC
tO
mA
40
Output pOwer Output rippLe VOut Line reguLatiOn Vin = 16 tO 40 VDC LOaD reguLatiOn 8 BALAnCED, 10% tO 100% input VOLtage
Vin = 16
tO
40 VDC
W
25C 10 kHz tO 2 MHz 10
kHz tO
2 MHz +VOut -VOut +VOut -VOut
mV p-p mV mV VDC V mA mA p-p
nO LOaD tO FuLL COntinuOuS TRAnSIEnT 50 ms 1 nO LOaD inHiBiteD 10
kHz
input Current input rippLe Current 3 eFFiCienCy LOaD FauLt 4 VOut Step LOaD reSpOnSe 5 VOut BaLanCeD LOaD Step Line reSpOnSe 1,5 VOut, 16 - 40 -16 VDC
- 10 MHz
25C, FuLL LOaD FuLL LOaD SHOrt CirCuit pOwer DiSSipatiOn reCOVery 1 50% - 100% - 50% tranSient reCOVery 1 tranSient reCOVery DeLay6 OVerSHOOt 1 25 C, nO eFFeCt On DC perFOrManCe
% W ms mV pk s mV pk s ms mV pk F
Start-up VOut
CapaCitiVe LOaD1
notes (see following page)
www.interpoint.com
Rev C - 20090318 - Pending Revision C Release
Page 6 of 10
Crane Aerospace & Electronics Power Solutions
sLH single and dual dc/dc converter cases
28 VoLt input - 1.5 Watt
Electrical Characteristics: -55 to + 125C Tc, 28 VDC Vin, balanced 100% load, unless otherwise specified.
notes SLH Dual Output Models: all temperatures refer to case temperature, tc 1. guaranteed by design, not tested. 2. Specified at 50%/50% balanced load. 3. With a series inductor on the Vin power lead (Lin = 6 H). 4. Load fault is a short circuit into 1 . Recovery is into resistive full load. 5. Transition > 10 s. Recovery is time for Vout to settle to within 1% of final value. 6. Measured from release of inhibit until Vout settles to within 1% of final value at full load with Vin at 28V. 7. Maximum specification indicates 80% of the converter's total power is available from either output, provided the other output carries 20% of the total power. 8. Although no minimum load is required, at no load the output voltage may exceed rating by up to 15%.
BOTTOM VIEW CASE A2
Projection Weld
0.805 max. (20.45) 0.697 (17.70) 0.018 0.002 dia. (0.46 0.05) 0.097 (2.46) 0.000 0.000 0.000 0.270 max (6.98) 0.27 0.02 (6.9 0.5)
Squared corner and dot on top of case indicate pin one.
12 3 4
7
6
5
0.135 (3.43) 0.235 (5.97)
0.435(11.05) 0.535 (13.59)
0.835 (21.21)
Case dimensions in inches (mm) Tolerance 0.005 (0.13) for three decimal places 0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300C for 10 seconds per pin Materials Header Kovar/Nickel/Gold Cover Kovar/Nickel Pins Kovar/Nickel/Gold matched glass seal
Case A2, Rev D, 20081119 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice.
Figure 2: CaSe a2
www.interpoint.com
Page 7 of 10 Rev C - 20090318 - Pending Revision C Release
0.980 max. (24.89)
Crane Aerospace & Electronics Power Solutions
sLH single and dual dc/dc converters
28 VoLt input - 1.5 Watt - pending reVision c reLease
Class H and K, MIl-PRF-38534 ElEMEnt EvaluatIon
COmpOnent-level test perfOrmed
spaCe prOtOtype (O) nOn-Qml1 m/s2 p3
no no N/A no no N/A N/A N/A N/A no no no no N/A no yes no no no no no no no no N/A no no no no no yes yes yes no no no no no no N/A N/A yes yes no no
Class h Qml m/s2 p3
yes yes N/A no no N/A N/A N/A N/A no no yes yes N/A yes
Class K Qml m/s2
yes yes yes yes yes yes yes yes yes N/A N/A yes yes yes no
p3
yes yes N/A yes yes N/A N/A N/A N/A yes yes yes yes N/A yes
Element Electrical Element Visual Internal Visual Temperature Cycling Constant Acceleration Interim Electrical Burn-in Post Burn-in Electrical Steady State Life Voltage Conditioning Aging Visual Inspection Final Electrical Wire Bond Evaluation4 SEM SLAMTM/C-SAM: Input capacitors only (Add'l test, not req. by H or K)
Notes: 1. Non-QML products do not meet all of the requirements of MIL-PRF-38534. 2. M/S = Active components (Microcircuit and Semiconductor Die) 3. P = Passive components 4. Not applicable to EMI filters that have no wirebonds. Definitions: Element Evaluation: Component testing/screening per MIL-STD-883 as determined by MIL-PRF-38534 SEM: Scanning Electron Microscopy SLAMTM: Scanning Laser Acoustic Microscopy C-SAM: C - Mode Scanning Acoustic Microscopy
www.interpoint.com
Rev C - 20090318 - Pending Revision C Release
Page 8 of 10
Crane Aerospace & Electronics Power Solutions
sLH single and dual dc/dc converters
28 VoLt input - 1.5 Watt - pending reVision c reLease
Class H and K, MIl-PRF-38534 EnvIRonMEntal sCREEnIng
end item-level test perfOrmed
Non-destruct bond pull2 Method 2023 Pre-cap Inspection Method 2017, 2032 Temperature Cycle (10 times) Method 1010, Cond. C, -65C to 150C, ambient Constant Acceleration Method 2001, 3000 g PIND Test Method 2020, Cond. A Pre burn-in test Burn-in Method 1015, 125C case, typical 96 hours 160 hours 2 x 160 hours (includes mid-BI test) Final Electrical Test MIL-PRF-38534 Group A, Subgroups 1 through 6 -55C, +25C, +125C case Radiography Method 2012 Post Radiography Electrical Test Room temperature Hermeticity Test Fine Leak, Method 1014, Cond. A Gross Leak, Method 1014, Cond. C Final visual inspection Method 2009
spaCe prOtOtype (O) nOn-Qml1
no yes
Class h Qml
yes3 yes
Class K Qml
yes yes
yes yes no yes
yes yes yes3 yes
yes yes yes yes
yes no no
no yes no
no no yes
yes N/A N/A yes yes yes
yes N/A N/A yes yes yes
yes yes yes3 yes yes yes
Test methods are referenced to MIL-STD-883 as determined by MIL-PRF-38534. Notes: 1. Space Prototype (O), non-QML products, do not meet all of the requirements of MIL-PRF-38534. 2. Not applicable to EMI filters that have no wirebonds. 3. Not required by DSCC but performed to assure product quality.
www.interpoint.com
Rev C - 20090318 - Pending Revision C Release
Page 9 of 10
Crane Aerospace & Electronics Power Solutions
sLH single and dual dc/dc converters
28 VoLt input - 1.5 Watt
Class H and K, MIl-PRF-38534 RadIatIon assuRanCE
envirOnmental sCreening levels radiatiOn hardness assUranCe levels
O1: Standard, no radiation guarantee OO HO N/A
spaCe prOtOtype (O) nOn-Qml2
Class h Qml
Class K Qml
r3: Radiation tolerant-Tested lots up to 100 K Rads (Si) total dose SEU guarantee up to 40 MeV
N/A
HR
KR
Notes: 1. Interpoint model numbers use an "O" in the RHA designator position to indicate the "-" (dash) Radiation Hardness Assurance level of MIL-PRF-38534, which is defined as "no RHA". 2. Space Prototype (O), non-QML, products do not meet all of the requirements of MIL-PRF-38534. 3. Redmond site, Interpoint, has a Radiation Hardness assurance plan on file with DSCC.
SLH Single and Dual, Rev C - 20090318 - Pending Revision C Release. This revision supersedes all previous releases. All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. SLH Series is a trademark of Interpoint. Copyright (c) 1999 - 2009 Interpoint Corporation. All rights reserved. www.interpoint.com
Page 10 of 10

▲Up To Search▲

Price & Availability of SLH2815DKR

	To Download SLH2815DKR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .