|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Data Sheet, Nov. 2008 Control integrated Power System (CIPOSTM) IKCS12F60AA IKCS12F60AC http://www.infineon.com/cipos Power Management & Drives Never stop thinking. CIPOSTM IKCS12F60AA IKCS12F60AC Revision History: Previous Version: Page 4 10 14 2009-04 2.2 Subjects (major changes since last revision) High temperature stress tests duration Changed VIT,HYS Updated Zth-diagram of Diode Rev. 2.3 Authors: W. Frank, W. Brunnbauer Edition 2007-07 Published by Infineon Technologies AG 85579 Neubiberg, Germany (c) Infineon Technologies AG 4/6/09. All Rights Reserved. Attention please! The information given in this data sheet shall in no event be regarded as a guarantee of conditions or characteristics ("Beschaffenheitsgarantie"). With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office or representatives (http://www.infineon.com). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office or representatives. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. TrenchStop(R) is a registered trademark of Infineon Technologies AG. CIPOSTM, CoolMOSTM, CoolSETTM, DuoPackTM and thinQ!TM are trademarks of Infineon Technologies AG. Data Sheet 2/19 Rev. 2.2, Nov. 2008 CIPOSTM IKCS12F60AA IKCS12F60AC Table of Contents CIPOSTM Control integrated Power System..................................................................................................4 Features........................................................................................................................................................4 Target Applications .....................................................................................................................................4 Description...................................................................................................................................................4 System Configuration .................................................................................................................................4 Internal Electrical Schematic...........................................................................................................................5 Pin Assignment.................................................................................................................................................6 Pin Description ............................................................................................................................................6 /HIN1,2,3 and /LIN1,2,3 (Low side and high side control pins, Pin 15 - 20) .............................................. 6 EN (enable, Pin 24) .................................................................................................................................... 7 ITRIP (Over-current detection function, Pin 21) ......................................................................................... 7 VDD, VSS (control side supply and reference, Pin 22, 23)........................................................................ 7 VB1,2,3 and VS1,2,3 (High side supplies, Pin 1, 2, 4, 5, 7, 8)................................................................... 7 VRU, VRV, VRW (low side emitter, Pin 12, 13, 14) ................................................................................... 7 V+ (positive bus input voltage, Pin 10)....................................................................................................... 7 Absolute Maximum Ratings ............................................................................................................................8 Module Section ............................................................................................................................................8 IGBT and Diode Section .............................................................................................................................8 Control Section............................................................................................................................................9 Recommended Operation Conditions............................................................................................................9 Static Parameters ...........................................................................................................................................10 Dynamic Parameters ......................................................................................................................................11 Integrated Components .................................................................................................................................12 Circuit of a Typical Application.....................................................................................................................12 Characteristics................................................................................................................................................13 Test Circuits and Parameter Definiton .........................................................................................................15 Package Outline IKCS12F60AA ....................................................................................................................18 Package Outline IKCS12F60AC ....................................................................................................................19 Data Sheet 3/19 Rev. 2.2, Nov. 2008 CIPOSTM IKCS12F60AA IKCS12F60AC CIPOSTM Control integrated Power System Single In-Line Intelligent Power Module 3-bridge 600V / 12A @ 25C Features * * * * * * * * * * * * * Fully isolated Single In-Line molded module TrenchStop(R) IGBTs with lowest VCE(sat) Optimal adapted antiparallel diode for low EMI Integrated bootstrap diode and capacitor Rugged SOI gate driver technology with stability against transient and negative voltage Temperature monitor and over temperature shutdown Overcurrent shutdown Undervoltage lockout at all channels Matched propagation delay for all channels Low side emitter pins accessible for all phase current monitoring (open emitter) Cross-conduction prevention Lead-free terminal plating; RoHS compliant Qualified according to JEDEC1 (high temperature stress tests for 1000h) for target applications Description The CIPOSTM module family offers the chance for integrating various power and control components to increase reliability, optimize PCB size and system costs. This SIL-IPM is designed to control AC motors in variable speed drives for applications like air conditioning, compressors and washing machines. The package concept is specially adapted to power applications, which need extremely good thermal conduction and electrical isolation, but also EMI-save control and overload protection. The features of Infineon TrenchStop(R) IGBTs and antiparallel diodes are combined with a new optimized Infineon SOI gate driver for excellent electrical performance. System Configuration * 3 halfbridges with TrenchStop(R) IGBT & FWEmConTM diodes * 3 SOI gate driver * Bootstrap diodes for high side supply * Integrated 100nF bootstrap capacitance * Temperature sensor, passive components for adaptions * Isolated heatsink * Creepage distance typ. 3.2mm Target Applications * Washing machines * Consumer Fans and Consumer Compressors Certification UL 1577 (UL file E314539) 1 J-STD-020 and JESD-022 4/19 Rev. 2.2, Nov. 2008 Data Sheet CIPOSTM IKCS12F60AA IKCS12F60AC Internal Electrical Schematic V+ (10) Tr1, U-HS D1 Tr3, V-HS D3 Tr5, W-HS D5 Tr2, U-LS D2 Tr4, V-LS D4 Tr6, W-LS D6 VRU (12) VRV (13) VRW (14) U, VS1 (8) V, VS2 (5) W, VS3 (2) RH1 RL1 RH2 RL2 RH3 RL3 VB3 (1) VB2 (4) VB1 (7) CbsH1 Dbs1Dbs3 CbsH2 CbsH3 Rbs VDD (22) /HIN1 (15) /HIN2 (16) /HIN3 (17) /LIN1 (18) /LIN2 (19) /LIN3 (20) ITRIP (21) EN (24) C1 VCC /HIN1 /HIN2 /HIN3 /LIN1 /LIN2 /LIN3 Driver-IC R RTS For integrated components see Table C2 VSS (23) Figure 1: Internal Schematic Data Sheet 5/19 Rev. 2.2, Nov. 2008 CIPOSTM IKCS12F60AA IKCS12F60AC Pin Assignment Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Pin Name VB3 W,VS3 n.a. VB2 V,VS2 n.a. VB1 U,VS1 n.a. V+ n.a. VRU VRV VRW /HIN1 /HIN2 /HIN3 /LIN1 /LIN2 /LIN3 ITRIP VDD VSS EN Pin Description high side floating IC supply voltage motor output W, high side floating IC supply offset voltage None high side floating IC supply voltage motor output V, high side floating IC supply offset voltage None high side floating IC supply voltage motor output U, high side floating IC supply offset voltage None positive bus input voltage None low side emitter low side emitter low side emitter input gate driver high side 1/U input gate driver high side 2/V input gate driver high side 3/W input gate driver low side 1/U input gate driver low side 2/V input gate driver low side 3/W input overcurrent shutdown module control supply module negative supply input logic enable, output temperature monitoring Pin Description /HIN1,2,3 and /LIN1,2,3 (Low side and high side control pins, Pin 15 - 20) These pins are active low and they are responsible for the control of the integrated IGBT The Schmitt-trigger input threshold of them are such to guarantee LSTTL and CMOS compatibility down to 3.3V controller outputs. Pull-up resistor of about 75 kOhm is internally provided to pre-bias inputs during supply start-up and a zener clamp is provided for pin protection purposes. Input schmitt-trigger and noise filter provide beneficial noise rejection to short input pulses. It is recommended for proper work of CiPoSTM not to provide input pulse-width lower than 1us. The integrated gate drive provides additionally a shoot through prevention capability which avoids the simultaneous on-state of two gate drivers of the same leg (i.e. HO1 and LO1, HO2 and LO2, HO3 and LO3). Figure 2: Input pin structure Data Sheet 6/19 Rev. 2.2, Nov. 2008 CIPOSTM IKCS12F60AA IKCS12F60AC A minimum deadtime insertion of typ 380ns is also provided, in order to reduce cross-conduction of the external power switches. EN (enable, Pin 24) The signal applied to pin EN controls directly the output stages. All outputs are set to LOW, if EN is at LOW logic level. The internal structure of the pin is the same as Figure 2 made exception of the switching levels of the Schmitt-Trigger, which are here VEN,TH+ = 2.1 V and VEN,TH- = 1.3 V. The typical propagation delay time is tEN = 900 ns. The IC shuts down all the gate drivers power outputs, when the VCC supply voltage is below VDDUV- = 10.4 V. This prevents the external power switches from critically low gate voltage levels during on-state and therefore from excessive power dissipation. VB1,2,3 and VS1,2,3 (High side supplies, Pin 1, 2, 4, 5, 7, 8) VB to VS is the high side supply voltage. The high side circuit can float with respect to VSS following the external high side power device emitter/source voltage. Due to the low power consumption, the floating driver stage is supplied by an integrated bootstrap circuit connected to VDD. This includes also Figure 3: Internal Circuit at pin EN This pin may also be used for reading out the temperature close to the gate drive IC. Please refer to section "Integrated Components" for the specification of the integrated parts. ITRIP (Over-current detection function, Pin 21) CiPoSTM provides an over-current detection function by connecting the ITRIP input with the motor current feedback. The ITRIP comparator threshold (typ 0.46V) is referenced to VSS ground. A input noise filter prevents the driver to detect false over-current events. Over-current detection generates a hard shut down of all outputs of the gate driver after the shutdown propagation delay of typically 900ns. The fault-clear time is set to typically to 4.7 ms. VDD, VSS (control side supply and reference, Pin 22, 23) VDD is the low side supply and it provides power both to input logic and to low side output power stage. Input logic is referenced to VSS ground as well as the under-voltage detection circuit. The under-voltage circuit enables the device to operate at power on when a supply voltage of at least a typical voltage of VDDUV+ = 12.1 V is at least present. Figure 4: Input filter timing diagram integrated bootstrap capacitors of 100 nF at each floating supply, which are located very close to the gate drive circuit. The under-voltage detection operates with a rising supply threshold of typical VBSUV+ = 12.1 V and a falling threshold of VDDUV- = 10.4 V according to Figure 4. VS1,2,3 provide a high robustness against negative voltage in respect of VSS of -50 V. This ensures very stable designs even under rough conditions. VRU, VRV, VRW (low side emitter, Pin 12, 13, 14) The low side emitters are available for current measurements of each phase leg. It is recommended to keep the connection to pin VSS as short as possible in order to avoid unnecessary inductive voltage drops. V+ (positive bus input voltage, Pin 10) The high side IGBT are connected to the bus voltage. It is recommended, that the bus voltage does not exceed 500 V. Data Sheet 7/19 Rev. 2.2, Nov. 2008 CIPOSTM IKCS12F60AA IKCS12F60AC Absolute Maximum Ratings (Tc = 25C, if not stated otherwise) Module Section Description Condition Symbol Min Storage temperature range Operating temperature control PCB1 Solder temperature Insulation test voltage Mounting torque Mounting pressure on surface Creepage distance External bootstrap capacitor single capacitor charging, VDD = 15V Wave soldering, 1.6mm (0.063in.) from case for 10s Value max 125 125 260 -40 - Unit C C C Tstg TPCB Tsol RMS, f=50Hz, t =1min VISOL 2500 3.1 0.6 150 19 V Nm N/mm mm F M3 screw and washer MS Package flat on mounting surface NMC dS Cbs,ext IGBT and Diode Section Description Condition Symbol min Max. blocking voltage DC output current Repetitive peak collector current Short circuit withstand time2 (SCSOA) IGBT reverse bias safe operating area (RBSOA) Power dissipation per IGBT Operating junction temperature range VIN=5V, IC=0.25mA Tc = 25C,TvJ < 150C Tc = 80C,TvJ < 150C tp limited by TvJmax VDD = 15V,VDC 400V, Tj 150C VDD = 15V,VDC 500V, Tj = 150C, IC = 6A VCEmax = 600V Value max 12 6 18 5 Unit VCES Iu, Iv, Iw Iu, Iv, Iw tsc 600 -12 -6 -18 - V A A s Full Square Ptot TvjI TvjD -40 -40 35 150 150 W C Tc = 25C IGBT Diode 1 2 Monitored by pin 24 Allowed number of short circuits: <1000; time between short circuits: >1s. 8/19 Rev. 2.2, Nov. 2008 Data Sheet CIPOSTM IKCS12F60AA IKCS12F60AC Description Condition Symbol min Value typ max 3.0 4.2 Unit Single IGBT thermal resistance, junction-case Single diode thermal resistance, junction-case Control Section Description Module supply voltage High side floating supply voltage (VB vs. VS) High side floating IC supply offset voltage Input voltage Operating junction temperature1 Max. switching frequency tp < 500ns LIN, HIN, EN, ITRIP Condition RthJC RthJCD - K/W Symbol VDD VBS VS1,2,3 Vin TJ,IC fPWM -1 -1 Value min max 20 20 600 10 125 20 Unit V V V V C kHz VDD-VBS-6 VDD-VBS-50 -1 - Recommended Operation Conditions All voltages are absolute voltages referenced to VSS -Potential unless otherwise specified. Description Symbol Value min High side floating supply offset voltage High side floating supply voltage (VB vs. VS) Low side power supply Logic input voltages LIN,HIN,EN,ITRIP VS VBS VDD VIN -3 12.5 12.5 0 max 500 17.5 17.5 5 V Unit 1 Monitored by pin 24 9/19 Rev. 2.2, Nov. 2008 Data Sheet CIPOSTM IKCS12F60AA IKCS12F60AC Static Parameters (Tc = 25C, if not stated otherwise) Description Condition Symbol min Collector-Emitter blocking voltage Collector-Emitter saturation voltage VIN = 5V, IC = 0.25mA VDD = 15V, Iout = +/- 6A 25C 150C VIN =5V, Iout = +/- 6A 25C 150C VCE = 600V, VIN = 5V Tj = 25C Tj = 150C VDD = 15V, tSC 5s VDC = 400V, TvJ = 150C V(BR)CES VCE(sat) 600 1.7 0.7 1.9 1.1 360 45 11.0 9.5 1.2 9.0 Value typ 1.6 1.9 1.65 1.6 40 2.1 0.9 2.1 1.3 460 75 12.1 10.4 1.7 10.1 360 2.0 55 110 75 180 30 max 2.1 2.05 A 40 1000 2.4 1.1 2.3 1.5 540 12.8 11.0 13.0 550 3.0 100 200 120 300 A V V V V mV mV V V V V A mA A A A A A V Unit Diode forward voltage VF Zero gate voltage collector current of IGBT Short circuit collector current1 Logic "0" input voltage (LIN,HIN) Logic "1" input voltage (LIN,HIN) EN positive going threshold EN negative going threshold ITRIP positive going threshold ITRIP input hysteresis VDD and VBS supply undervoltage positive going threshold VDD and VBS supply undervoltage negative going threshold VCC and VBS supply undervoltage lockout hysteresis Input clamp voltage (/HIN, /LIN, EN, ITRIP) Quiescent VBx supply current (VBx only) Quiescent VDD supply current (VDD only) Input bias current Input bias current ITRIP Input bias current EN Input bias current Leakage current of high side ICES IC(SC) 2 VIH VIL VEN,TH+ VEN,THVIT,TH+ VIT,HYS VDDUV+ VBSUV+2 VDDUVVBSUV-2 VDDUVH VBSUVH2 IIN = 4 mA VHIN = low VIN = float VIN = 5V VIN = 0V VITRIP = 5V VEN = 5V Tj,IC = 125C, VS = 600V VINCLAMP IQB IQDD IIN+ IINIITRIP+ IEN+ ILVS2 1 2 Allowed number of short circuits: <1000; time between short circuits: >1s. Test is not subject of product test, verified by characterisation 10/19 Rev. 2.2, Nov. 2008 Data Sheet CIPOSTM IKCS12F60AA IKCS12F60AC Dynamic Parameters (Tc = 25C, if not stated otherwise) Description Condition Symbol min Turn-on propagation delay High side or low side Turn-on rise time High side or low side Turn-off propagation delay High side or low side Turn-off fall time High side or low side Shutdown propagation delay ENABLE Shutdown propagation delay ITRIP Input filter time ITRIP Input filter time at LIN for turn on and off and input filter time at HIN for turn on only Input filter time at HIN for turn off Input filter time at HIN for turn off Input filter time EN Fault clear time after ITRIP-fault Min. deadtime between low side and high side Deadtime of gate drive circuit IGBT Turn-on Energy (includes reverse recovery of diode) IGBT Turn-off Energy Iout = 6A, VDC = 300V Tvj = 25C Tvj = 150C Iout = 6A, VDC = 300V Tvj = 25C Tvj = 150C Iout = 6A, VDC = 300V Tvj = 25C Tvj = 150C VLIN,HIN = 0 V & 5V VITRIP = 0 V VLIN,HIN = 0V; Iout = 6A, VDC = 300V Iout = 6A, VDC = 300V VLIN,HIN = 5V VLIN,HIN = 5V; Iout = 6A, VDC = 300V Iout = 6A, VDC = 300V VLIN,HIN = 0V VEN = 0V, Iu, Iv, Iw = 6A VITRIP = 1V, Iu, Iv, Iw = 6A VITRIP = 1V VLIN,HIN = 0 V & 5V td(on) tr td(off) tf tEN tITRIP tITRIPmin tFILIN 155 120 Value typ 617 21 832 29 900 900 210 270 max 380 ns ns ns ns ns ns ns ns Unit VHIN = 5V VHIN = 5 V tFILIN1 tFILIN2 tFILEN tFLTCLR DTPWM DTIC Eon 300 - 220 400 430 4.7 1 380 145 195 122 160 31 81 - ns ns ns ms s ns J Eoff J J - Diode recovery Energy Erec Data Sheet 11/19 Rev. 2.2, Nov. 2008 CIPOSTM IKCS12F60AA IKCS12F60AC Integrated Components Description Condition Symbol1 min Resistor (0.25 W) Resistor Resistor B-Constant of NTC (Negative Temperature Coefficient) Bootstrap diode forward voltage Capacitor Capacitor Bootstrap Capacitor TNTC = 25C TNTC = 25C IFDbs = 100mA Rbs R RTS B25 VFDbs C1 C2 CbsHx Value typ 10 24 100 4250 1.9 100 2.2 100 max 2.05 K V nF k Unit Circuit of a Typical Application 1 Symbols according to Figure 1 12/19 Rev. 2.2, Nov. 2008 Data Sheet CIPOSTM IKCS12F60AA IKCS12F60AC Characteristics 1000ns td(off) td(on) 1000ns td(off) td(on) t, SWITCHING TIMES 100ns tr t, SWITCHING TIMES 100ns tf tf 10ns tr 10ns 25C 0A 5A 10A 15A 50C 75C 100C 125C IC, COLLECTOR CURRENT Figure 5. Typical switching times as a function of collector current (inductive load, TJ=150C, VCE = 300V, VDD = 15V Dynamic test circuit in Figure A) TvJ, JUNCTION TEMPERATURE Figure 6. Typical switching times as a function of junction temperature (inductive load, VDD= 15V, VCE = 300V, IC = 6A Dynamic test circuit in Figure A) Eon E, SWITCHING ENERGY LOSSES E, SWITCHING ENERGY LOSSES 1.25mJ Eon 0.15mJ Eoff 1.00mJ 0.75mJ 0.10mJ 0.50mJ Eoff 0.05mJ Erec 0.25mJ Erec 0.00mJ 25C 50C 75C 100C 125C 0.00mJ 0A 5A 10A 15A IC, COLLECTOR CURRENT Figure 7. Typical switching energy losses as a function of collector current (inductive load, TJ = 150C, VCE = 300V, VDD = 15V Dynamic test circuit in Figure A) TvJ, JUNCTION TEMPERATURE Figure 8. Typical switching energy losses as a function of junction temperature (inductive load, VCE = 300V, VDD = 15V, IC = 6A Dynamic test circuit in Figure A) Data Sheet 13/19 Rev. 2.2, Nov. 2008 CIPOSTM IKCS12F60AA IKCS12F60AC 12V 10V 15A VGE=25C 125C 150C VEN, VOLTAGE AT PIN EN 8V IC, COLLECTOR CURRENT 75C 100C 12A 6V 9A 4V Vdd = 2V 10.3V 15V 20V 6A 3A 0V 25C 50C 0A 0V 1V 2V 3V TC, CASE TEMPERATURE Figure 9. Typical voltage at pin EN as a function of case temperature VCE, COLLECTOR EMITTER VOLTAGE Figure 10. Typical output characteristic of IGBT as a function of collector emitter voltage (VDD = 15V) 15A ZthJC, TRANSIENT THERMAL RESISTANCE Single Pulse IGBT Diode 10 K/W 0 IF, forward CURRENT 12A 9A 6A VGE=25C 3A 125C 150C 10 K/W -1 0A 0V 1V 2V 10 K/W -2 1s 10s 100s 1ms 10ms 100ms 1s VF, forward VOLTAGE Figure 11. Typical diode forward current as a function of forward voltage tP, PULSE WIDTH Figure 24. Transient thermal impedance as a function of pulse width (D=tP/T) Data Sheet 14/19 Rev. 2.2, Nov. 2008 CIPOSTM IKCS12F60AA IKCS12F60AC C, MAXIMUM EXT. BOOTSTRAP CAPACITOR 100F 10F 1F 10V 12V 14V 16V 18V VDD, SUPPLY VOLTAGE Figure 12. Maximum ext. bootstrap capacitor as a function of supply voltage VDD (TJ=25C, single capacitor charging) Data Sheet 15/19 Rev. 2.2, Nov. 2008 CIPOSTM IKCS12F60AA IKCS12F60AC Test Circuits and Parameter Definition Erec = vD i F dt 0 t Erec Figure A: Dynamic test circuit Leakage inductance L =180nH Stray capacitance C =39pF Figure B: Definition of diodes switching characteristics Figure C: Definition of Enable and ITRIP propagation delay LIN1,2,3 HIN1,2,3 2.1V 0.9V td(off) tf td(on) tr 90% 10% tEoff t Eoff iCU, iCV, iCW vCEU, vCEV, vCEW 90% 10% 10% tEon 2% 2% Eoff = vCEx i Cx dt 0 Eon = vCEx i Cx dt 0 t Eon Figure D: Switching times definition and switching energy definition Data Sheet 16/19 Rev. 2.2, Nov. 2008 CIPOSTM IKCS12F60AA IKCS12F60AC tFILIN HIN LIN tFILIN LIN on off on off high LO HO LO low a) HIN tFILIN1 toff,HINx tFILIN2 toff,HINx < tFILIN1 high HO b) HIN toff,HINx toFILIN1 < toff,HINx < tFILIN2 HO c) HIN toff,HINx toff,HINx > tFILIN2 HO Figure E: Short Pulse suppression Data Sheet 17/19 Rev. 2.2, Nov. 2008 CIPOSTM IKCS12F60AA IKCS12F60AC Package Outline IKCS12F60AA Note: There may occur discolourations on the copper surface without any effect on the thermal properties. Data Sheet 18/19 Rev. 2.2, Nov. 2008 CIPOSTM IKCS12F60AA IKCS12F60AC Package Outline IKCS12F60AC Description Condition Symbol min Value typ 17 max - Unit Weight mP - g Note: There may occur discolourations on the copper surface without any effect on the thermal properties. Data Sheet 19/19 Rev. 2.2, Nov. 2008 |
Price & Availability of IKCS12F60AA |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |